User Manual 45 35 Green Wire - Ground 1.Scan QR code and download the app iOS or Android version Features Installation Connection & Operation APP Operation WIFI Connection Mechanical ON/OFF Switch 1 0 5 0 7 Product Introduction
- Excellent design and high-quality materials to ensure long-
term stable and reliable service to users
- Wi-Fi connection has the most applicability, and has access
- Silent mechanical push button design provide the user's best Smart Switch V1.0 Normal 3 Way WiFi 802.11 b/g/n 2.4GHz N L L1 N L L1 Tra 100~240V AC 50~60Hz Relay 1 CH 15A 0.5W 500K times 105*45*42.5mm N L L1 Tra N L L1 Tra Red Wire - Tra (3 Way) e n L i l a r t u e N
e r i W e t i h W d a o L
e r i W d e R n i i e n L
e r i W k c a B l Wiring Instruction of 3 Way Wiring Instruction of Normal Black Wire Line In Red Wire Load White Wire Neutral Line Green Wire Ground Blue Wire Tra (3 Way) 1. Disconnect power by circuit breaker 2. Check the Line with voltage tester pen, make sure the power is o to prevent electric shock 3. Follow the wiring instructions, connect the dimmer wires to each other leads and check for short circuits 4. Screw the dimmer into the back box 5. Mounting switch cover plate 6. Connect circuit breaker restore power On/O Button Status LED 2. Register and log in The user needs to register by mobile phone number. in the After registration, you can use this username to log APP and proceed to the next step.
*Support some third-party accounts log in directly . 1. Once connect power correctly, the Green led on the bottom of switch will turn on, switch is ready to serve 2. Push on/o button to turn on/o the light Reset the product:
Press and hold ON/OFF button for 5 seconds then release, Green power indicator will ash, switch get into setup mode, please follow setup instruction to complete setup to start smart function APP Operation 3. Add Devices
+ eht kcilc ,nigol resu eht retfA icon in the upper right corner To ensure that the new switch power LED is ashing, select of the main page to enter the add device interface, select the the Wi-Fi and enter the password then click Next. Switch menu and click the switch device icon APP Operation 5. Add Devices Wait system to search the device, connect and congure the device will takes up to 3min. Once the device congure successfully, please also input preferred name and select location. APP Operation 6. Control switch with APP APP Operation FCC Caution. 8. All added devices can be viewed in the main menu of the APP is subject to the following two conditions: (1) This device may to multiple platforms feedback Specication Input Power:
Control:
Communication:
Control Channel:
Max Current:
Standby Power:
Button Life:
Dimension:
APP Operation 4. Add Devices 7. Add timer mode in the APP Remark:
1. Smart phone and device must connect to same Wi-Fi during setup mode 2. The device must be added to the account before it can be controlled remotely 3. After the device is successfully accessed, other users can obtain control of the product through the sharing function. Troubleshooting 1. Can not connect to Wi-Fi router a) Also make sure you have good Wi-Fi signal strength at the location of the switch b) Metal box and metal surface - wall board may block Wi-Fi signal c) Make sure input correct Wi-Fi password d) The switch only support 802.11 b/g/n 2.4GHz Wi-Fi signal, 5GHz NOT support This device complies with part 15 of the FCC Rules. Operation not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 15.21 Information to user. Any Changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.105 Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set environment. This equipment should be forth for an uncontrolled installed and operated with minimum distance 20 cm between the radiator and your body. ISED Statement
(2) subject device English:
This Operation following to the is device nd This must accept device. of operation the The apparatus digital French:
complies with any complies with Canada two conditions:
device Industry This including
(1) interference, interference licenseexempt not cause may that may standard(s). RSS interference, a undesired cause le de RF pas can RSS 102 CAN doit 3 (b). users obtain le licence. produire accepter Canadian exposure, 3 (b) / nmb information fonctionnement. Canadian aux prsentappareilestconforme Le exempts de ICES3 CNR d'Industrie L'exploitationestautorise aux deux de l'utilisateur l'appareildoit et
(2) brouillageest susceptible d'encompromettre
(B)/NMB3(B). applicables Canada aux appareils suivantes:
conditions
(1) l'appareil brouillageradi tout radio ne brouillage, olectriquesubi, mmesi l'appareil numrique du ciem conforme canadien peut This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and with compliance exposure and compliance. cet appareil est conforme l'exemption des cnr donnes canadiennes sur l'exposition aux champs rf et la conformit. This environment. This radiator & your body. Cet quipement est conforme Canada limites d'exposition aux radiations dans un environnement non contrl. Cet quipement doit tre install et utilis une distance minimale de 20 cm entre le radiateur et votre corps. limites d'valuation courante dans la section 2.5 du des should uncontrolled l'exposition utilisateurs equipment conformit equipment minimum exposure operated radiation complies between installed distance peuvent obtenir Canada 20cm limits forth avec with with and 102 102 aux set for the rss les on be de RF an rf, et