1. Power On 1. To check your camera image, You should turn on cameras, monitor, sensor, etc, before you turn on iDRS-3000. 2. Turn on iDRS-3000.
[POWER] lamp will light on, disk check(red LED) blinks then WINDOWS 98 starts. After booting main screen will appear as follows. 3. Main Screen 1) Activated icon will be turned green and show TIP of each icon, when mouse pointer get close to each icon. Inactivated icon will be turned yellow. 2) When consecutive recording, red lamp is 3) When motion recording, blue lamp is 4) When sensor recording, yellow lamp is 5) When [Record] lamp is on and off, it is displayed in OSD(Camera Name). displayed in OSD(Camera Name). displayed in OSD(Camera Name). consecutive recording, [Motion] lamp is on and off, it is motion recording, [Sensor] lamp is on and off, it is sensor recording. 6) Put your mouse pointer to image screen, click left button to enlarge corresponding screen. And click right button to extend to full screen. 7) Click right button in full screen mode to back to main screen. 8)
[System Shutdown] If you click this icon, confirmation message will appear as follows. If you select [OK] system will be shut down and automatically power OFF.
- 1 -
Single-Screeen Rotational Display 9) 10) [Motion Tracer] Enlarge a screen in which the motion is detected. 11) [Set up] Change iDRS-3000 set up configurations. (Refer to the 2. Set up Change) 12) [Image search/Playback] Search recorded image. (Refer to the 3. See * 3. Image Search) 13) [Camera ON/OFF] Camera ON/OFF icon. When P/T control select camera as 13). If you click this icon power off th4e corresponding camera. Quad(4)-screen Rotational All-Channel Display. 14) Camera Pan/Tilt Control Button.
[ - left / - right / - up / - down]
[Zoom] Control motorized zoom lens. 15) 16) [Focus] Control camera lens focus. Zooming In Zooming Out Focus gets closer. Focus gets further. 17) [Light ON/OFF] Control Lighting Equipment. 18) Clock : Indicate present time and date. 19) In case you need to shut down the system by force, push POWER button for 4-5 seconds. But shutting down by force may cause fatal damage to the system itself and data. Please always use [Shut Down] button.
- 2 -
2. Set up change ( ) 1) [Camera set up]
Input camera number Put each camera name for OSD(On-Screen Display) zone. Set up each camera. If you click
[TOTAL BOARD] : Show total number of iDRS-CARDs.
[TOTAL SPEED] : Show maximum recording speed. Click to select camera to change camera name iDRS CARD number
- 3 -
system will automatically detect connected camera. 2) [Schedule]
Set up each group. Total 10 groups are available (programmable)
- Select group.
- Set the days of the week.
- Connect cameras, motion detectors(software sensor), (external) sensor and D/O. If you want to record specific time, please designate [START TIME], [END TIME].
- 00:00 to 00:00 means whole day(24 hours) recording.]
After designation, active corresponding group. Automatically connect Set up date, Camera, Sensor, D/O by click. It is not saved with disconnected camera, sensor, D/O, and also disconnected date.(click once again to disconnect.) 3) [Recording Speed]
Designate normal recording speed (Frame Rate).
(Separate frame rate for each camera is available.)
- 4 -
Designate motion-detected recording Frame Rate.
(Separate frame rate for each camera is available.) When sensor recording designate camera FRAME.
(Separate frame rate for each camera is available.)
[Switch Speed] : Adjust interval for rotational display model.
[Motion Delay] : Keep on recording after motion detection is finished, during indicated time.
[Sensor Delay] : Keep on recording after sensor detection is finished, during indicated time.
[Sensor Beep] : Activate BEEP sound on sensor detection.
[Proportion] : When activated, only 1, 4, 9, 16 divisions are available, to keep the horizontal and vertical ratio of each screen.
[Image Quality] : Adjust compression rate. At 100% quality, recorded image is clear and vivid but the size of a frame is bigger (15-20KB). At lower percentage (higher compression rate) image quality is relatively low but size of a frame is smaller (3-8KB). 34-50% is recommended.
(4) [Motion] Motion Detector configuration Set up motion detection zone. It would be seen in red square(Maximum 10 areas per camera). If motion detector is connected in Schedule menu but no detection zone is defined, system will recognize whole screen as a detection zone. When motion recording mode, detection BEEP sound can be activated/inactivated. Detected motion is seen in blue unit square, and indicating red MOTION DETECTON.
[SENSITIVITY] : Setting sensitivity of software motion detector At high sensitivity even the very trivial motion will detected. Adjust it to proper level.(30% - 40% is recommended) Delete all motion detection zone.
- 5 -
5) [Password]
Set up password, to prevent other person than operator from changing setup. If you set up new password click [APPLY]
to use new password. Please do not forget password.
(Set up change is impossible) 6) [Close Set up] : Back to main screen. 3. Image Search( )
( ) 1) [Camera(Channel) Number] : Select camera number to playback.
- 6 -
2) [Date select] : Recorded date is checked with red mark automatically. Click date to search. Previous Month - Next month If there is no recorded data in other month(s) month selection buttons are inactivated. High speed Playback To last cut of recorded screen Move back 1minute Play Stop Move forward 1minute Move back 1 cut Move forward 1 Cut To first cut of recorded screen 3) Playback Screen adjustment
: Contrast of search screen. ( Level control)
: Brightness of search screen. ( Level control) 4) Other functions Low level High level
[Media information] Check available disk capacity and frame size. Disk capacity is 9270MB, recorded capacity is 1090MB. 11%
is used. Average recording capacity is 8.46KB. So the expected recording period is about 13 days (311 hours 40 minutes).
[FDD backup] Save present screen in image file (JPG or BMP) to the floppy disk. In 1 FDD about 100 image cuts can be saved by JPG file or 30 cuts by BMP file
- 7 -
BACK-UP 1 cut, now seen in monitor by JPEG file in Floppy disk.
[Print] Print out present image. Stop the image to print and click. Selected screen is printed by printer.(Continuous print is available for 30 cuts) Time stamp (YYYY/MM/DD HH:MM:SS) will automatically be included. Assigning cut name and printing is available, click [set up] to set up printer driver PRINT OUT 1 cut from present image without name.
[Time search] Select time(hour, minute) for fast and accurate search/playback
: Start Search
[Close Play-Back Screen] Back to main screen.
- 8 -
iDRS-3000 Hardware System Requirements ITEM Minimum Recommended Not Recommended CPU Pentium-II Celeron 600 MHz Pentium-III 550 MHz
(or Higher) AMD Athlon (Not Tested) MAIN BOARD Intel 440BX Intel i815E Intel i820 SiS, Via Chipset RAM 64 MB
> 128 MB
< 64 MB HDD 15 GB
> 30 GB
< 10 GB VGA AGP 8M (Savage 3D) Savage 3D, Savage 4 Pro Ati-Series, Matrox Riva TNT Series, i740 Voodoo Series iDRS-3000 Installation Procedure
. Booting and HDD Format 1) Prepare a Windows-98 bootable floppy diskette. Booting the system from FDD. 2) Execute FDISK.COM and make three partitions as follows :
A. Primary Partition (C:) : For Windows and iDRS program (500MB 1 GB) B. Extended Partition : For recording. C. Logical Partition (D:) : For Sound recording (About10GB, assuming that the HDD is 45GB)
(Even in case the sound recording is not necessary, this drive must be partitioned. For example, 200MB 500MB) D. Logical Partition (E:) : For Video recording. All the remaining capacity. E. All the drives after E:, if exist owing to the HDD expansion, are recognized as Video recording partition. F. Be sure to make the primary partition as Active (Bootable) partition. 3) Reboot and Format Drive C:, D:, E: (Formatting in DOS mode is recommended.)
- 9 -
. Windows 98 Setup 1) Insert Windows 98 CD in your CD-ROM Drive and execute SETUP.EXE. 2) Proceed setup process, no special operation required. Install VGA driver 1) Insert VGA device driver (CD or Disk, provided by VGA card manufacturer) and install the same. Please refer to the VGA manual, for this step. 2) Execute CONTROL PANEL. 3) Open DISPLAY. 4) Set the video display mode as : resolution 800 x 600, True Color (32 bit) 5) Disable power saving function, to prohibit the monitor from getting into the power saving mode. A. Software setting : CONTROL PANEL -> POWER MANAGEMENT B. Hardware setting : POWER MANAGEMENT menu in CMOS setup
. Install iDRS-3000 Software 1) Insert iDRS-3000 (CD or Disk) and run SETUP.EXE and proceed as instructed by setup wizard. 2) Reboot the system. The system automatically detects capture board(s) and shows camera detection screen. In some main boards, there can be a problems in rebooting. In that case, A. START menu -> RUN -> Type REGEDIT and click OK B. Go to HKEY_LOCAL_MACHINE -> SYSTEM -> CurrentControlSet -> Control -> Shutdown C. Toggle FastReboot (If the default is 1, make it 0. & default is 0, make it 1) D. If the system is already running the iDRS software, you can execute Task Manager by double-clicking the clock in lower part of the main screen. Then execute Explorer or Regedit. 3) To avoid any possible unstableness, iDRS software is automatically started on system booting and shut down system on its closing. In case the user wants to access windows :
A. During booting, push F8 key and start system by Command Prompt Only mode. B. Execute Edit.exe and open system.ini in C:\Windows folder C. Disable (or delete) the line shell=c:\zealot\standby.exe
- 10 -
IDRS----3000 IDRS 3000 3000 IDRS IDRS 3000 Sensor Connector Pin Sensor Connector Pin Sensor Connector Pin Sensor Connector Pin 13 25 1 14 PinPinPinPin Description Description Description Description Colo Colo Colo Colo rrrr Sensor 1 BLK 1 2 3 4 5 6 7 8 Sensor 2 BRW Sensor 3 RED Sensor 4 ORG Sensor 5 YEL Sensor 6 GRN Sensor 7 BLU Sensor 8 PUR Description Color PinPinPinPin Description Color Color Description Description Color PinPinPinPin Description Description Description Description Colo Colo Colo Colo rrrr WHT D/O 1 NC D/O 1 COM GRY D/O 1 NO D/O 2 NC BLU WHT D/O 2 COM GRY D/O 2 NO D/O 3 NC YEL WHT D/O 3 COM GRY D/O 3 NO D/O 4 NC ORG WHT D/O 4 COM GRY D/O 4 NO PUR 9 10 11 12 13 BLK BLK BLK BLK BLK GND GND GND GND GND 14 15 16 17 18 19 20 21 22 23 24 25
- 11 -