FCC ID: 2AWYXBC800 Body Weight Scale

BC800 3G Body Weight Scale Instruction Manual BC800 3G Summary Instruction Manual Package contents Display Indicators Operating Instructions Important Safety Information Speci cation Read the instruction manual before using the device Display Indicators Intended use: The Body Weight Scale BC800 3G is a digital monitor for home/domestic use which measures weight of persons 18 years of age or more. Time (hh:mm) Date (dd:mm:yyyy) Package contents Telecom signal strength Data send in progress Data send status *

Units

* Data sent successfully Data send failure Weight & measurement log:

If shows up, then total number of measurements sent is displayed. If shows up, then total number of measurements still stored on the scale is displayed. Body Weight Scale BC800 3G 4x1.5V AAA Alkaline batteries 1. Insert batteries 01 02 Place the scale upside down on a at surface being careful not to scratch it. the battery cover and Remove insert 41.5V AAA alkaline batteries with correct polarity. Overload Indicator Scale is overloaded (max. 180 kg, 396 lbs, 28.3 st) Low Battery Indicator Batteries are low and need to be replaced. Remove battery cover. 01 02 03 Insert batteries. Replace battery cover. 2. Operating Instructions Important Safety Information Place the scale on a hard, at surface. 04 Step on the scale and remain still during measurement. When the data send in progress indicator is displayed, the data is being sent and you may step off the scale. After a period of time, the data send status will be displayed. If it shows a data send failure, move the scale to a new location and try again. 01 02 03 Notes Weight measurements are possible withshoes and socks on. Calibration: if you place the body weight scale BC800 3G at new place, quickly step with one on it, until the display turns on. Step off and wait until the calibration gets performed(10-15 seconds)and the display switches off. If there is no signal strength indicator and you continue to receive a data send failure, contact your distribution partner. user should clean the glass surface before use. Please contact tonia@ebmtech.com for troubleshooting and maintenance. Automatic Shutdown If no measurement is being taken, the scale will automatically turn off in 10 seconds. Please read the entire instruction manual and safety precautions before using the Body Weight Scale BC800 3G. Unusual measurement values should be dis-

cussed with your doctor or health care pro-

fessional. Never change the dosage of any prescribed medications without rst consulting your doc-

tor or health care professional. Always perform the measurements on a hard and at surface. Uneven oors may affect the readings. If necessary, clean the Body Weight Scale BC800 3G with a damp cloth and a small amount of dishwashing liquid. When the sur-

face is dirty. Never immerse the scale in water or rinse it under running water. Protect the Body Weight Scale BC800 3G against knocks, moisture, dust, chemicals, drastic changes in temperature and electro-

magnetic elds. Keep the Body Weight Scale BC800 3G away from any sources of heat. Never step on the outer edge of the glass. This could cause the scale to tip or damage the glass. Keep packaging materials away from children. Store the Body Weight Scale BC800 3G hori-

zontally, not vertically. If the measurement appears inaccurate or if the LCD display does not show any gures, please check that the batteries are correctly inserted and the battery contacts are clean. If the Body Weight Scale BC800 3G will not be used for an extended period of time, remove the batteries from the Weight Scale BC800 3G and store it properly. Do not store other objects on top of it. Please use the device in a dry and clean envi-

ronment, and place the device on a at ground before use. Do not use hot water, volatile oil or rosin oil to clean the scale. Please store at room temperature, keep in a dry and cool place and avoid sun exposure. Do not run or jump near the Body Weight Scale BC800 3G. This product is applied parts(type BF).No maintenance required during the product life cycle. operation environment:

(1)

(2)

(1)

(C),/Relative Humidity Temperature

(%)/Atmospheric

(kPa):

10~40 C /15~90%RH / 70 kPa

~106 kPa Home healthcare. Pressure Temperature (oC),/Relative Humidity

(%)/Atmospheric Pressure (kPa):

-25~40C / 10~95%RH / 70 kPa

~106 kPa Transportation and storage environment:

Warning known contraindication: People are equipped with Pace Maker or other implant device shall not use this scale. Scale shall not be broke down or maintained in operation. Scale release a week current and it pass through the body. The current may affect electrical product and cause erroneous operation. The failure may become the cause of major accidents. Do not use a mobile phone or low frequency therapy device near the Scale. Prohibit any modi cation of the scale, it may cause hazards. EBM Technologies Inc. will provide circuit diagrams, component part lists, descriptions, calibration instructions to assist to service personnel in parts repair. 300 Measurements (Info: the Battery life depends on the used batteries. The time required for scale to warm from

-25oC between uses until scale is ready for its intended use when the ambient temperature is 20oC is 2 hours. The time required for the scale to cool from 40oC between uses until the scale is ready for its intended use when the ambient tempera-

ture is 20oC is 2 hours. If the degraded sensors and electrodes, or loosened electrodes, that can cause weight measurement failure .please contact EBM Technologies Inc. The waste products and batteries should fol-

low the domestic waste disposal regulation. Product life expectancy: 5 years To Avoid Injury Only use this device for its intended use and in accordance with the instruction manual. Do not use the device if it is damaged in any way. FCC compliance statement FCC SAR statement changes or modi cations not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter-

mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is con-

nected. Consult the dealer or an experienced radio/TV technician for help. Increase the separation between the equipment and receiver. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the speci c operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certi cation for use when properly worn on the body. Speci cation Sensors Maximum Capacity Increments Measurements Display Fault indications Data transmission Operating environment Frequency bands Output power High precision strain gauge sensors 180 kg / 396 lbs / 28.3 st 0.1 kg / 0.2 lbs / 0.01 st Weight White backlight LCD display Overload and low battery Over a 3G/2G mobile connection

(with Vodafone SIM card inside) Temperature 10~40C (50~104F) Humidity 15 %~90 % RH GSM/GPRS/EDGE: Dual band GSM 900/1800MHz UMTS/HSPA+: Dual band UMTS 900/2100MHz Class 4 (+33dBm 2dB) for EGSM900 Class 1 (+30dBm 2dB) for GSM1800 Class E2 (+27dBm 3dB) for GSM 900 8-PSK Class E2 (+26dBm +3 /-4dB) for GSM 1800 8-PSK Class 3 (+24dBm +1/-3dB) for UMTS 2100, WCDMA FDD BdI Class 3 (+24dBm +1/-3dB) for UMTS 900, WCDMA FDD BdVIII Automatic shutdown Yes, after 10 seconds Symbol Description Indicates the manufacturers serial number so that a speci c medical device can be identi ed. Indicates a medical device that needs to be protected from moisture. Indicates the need for the user to consult the instructions for use. Indicates the need for the user to consult the instructions for use for important cautionary information such as warnings and precautions that cannot, for a variety of reasons, be presented on the medical device itself. Hereby, EBM Technologies Inc. declares that the radio equipment type BC800 3Gis in compliance with directive FCC ID (FCC PART 22/24, IEEE 1528, KDB447498), IEC60601-1: 2005+A1:

2012, IEC60601-1-11: 2015, IEC606601-1-2: 2014, 2014/53/EU, 2014/30/EU, 2011/65/EU. EBM Technologies Inc. declares that the medical device weight scale BC800 3G is listing in FDA(Registered Establishment Number: 3004722076) Manufacturer EBM Technologies Inc. 5F. No. 516 Sec. 1 Neihu Road Taipei, Taiwan Distribution by Medisante USA, Inc. Suite 14A, 2077 Center Avenue

+1 973-851-6874 https://www.medisante-group.com/

Dennis.lottero@medisante-group.com Instruction Manual - Version 4, 2020/06 2017 Medisant. All rights reserved. 2AWYXBC800

BC800 3G Body weight Scale Serial number with digits IMEI: xxxxxxxxxxxx (digits) IMEI Barcode GTIN-13 4719878870016 FCC ID: 2AWYXBC800 IP21 15kg 180kg 4 x 1.5v AAA EBM Technologies Inc. 5F. No. 516 Sec. 1 Neihu Road Taipei, Taiwan Production DateDD/MM/YYYY Body Weight Scale BC800 3G This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 180mm/middle of device 55mm 55mm 38mm 30mm

SGS SGS North America Inc. 620 Old Peachtree Road Applicant Declaration SUITE 100 Suwanee, Georgia 30024

} United States Applicant Legal Business Name EBM Technologies Inc. Address 5F.,No.516,Sec.1,Neihu Road Taipei, Taiwan Grantee Code 2AWYX FCC ID 2AWY XBC800 Authorized Contact Name Jerry Huang Contact Email jerry@ebmtech.com Contact Phone 886-2-875 14567

|, the undersigned, certify that | am an authorized signatory for the Applicant and therefore declare;

a) b) c) qd) 9) in accordance with 47CFR2.911(d), all of the statements herein and the ex knowledge and belief.

's attached hereto are true and correct to the best of my in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

(1) labeling the equipment with the exact FCC ID as specified in this application,

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with IS$017065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing.

(2) the Applicant shail make provisions to always have a production sample available upon request by SGS, FCC and/or ISED.

(3) the Applicant shall, upon request by SGS, at the Applicant's expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or ibution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https:/Awww.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-requlations-title-47 Link to KDBs: https://a s.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https:/Avww.ic.gc.ca/eic/site/smt-gst.nsfleng/sf01130.html Applicant Signature: Date:

Z my Stary VO ; 0% 3 Print Name: _| Jerry Huang Title:

Regulatory Affairs Specialist NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Applicant Declaration Rev:0.0

EBM Technologies, Inc. TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: Confidentiality Request regarding application for FCC ID: 2AWYXBC800 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions Parts List / BOM Tune Up Procedure The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Print Name:Jerry huang Title: Regulatory Affairs Specialist Signature: ng Pry reo oy On behalf of Company: EBM Technologies, Inc. Telephone: 886-2-87514567 jerry@ebmtech.com

EBM Technologies, Inc. Date: 2020/08/03 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding:2AWYXBC800 To whom it may concern:

We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch and Keny Xu in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, | acknowledge that all responsibility for complying with the terms and con ied by SGS North America, Inc., still resides with EBM Technologies, Inc. nis valid until further written notice from the applicant. t Name: Jerry Huang Title: Regulatory Affairs Specialist Signature:

oe A Huang ALOU. of On behalf of Company: EBM Technologies, Inc. Telephone:886-2-87514567 jerry@ebmtech.com