Instruction Manual EN Instruction Manual ..............................................................................................................2 Congratulations on the purchase of your ECOVACS ROBOTICS DEEBOT! We hope it brings you many years of satisfaction. We believe that your new robot will help keep your home clean and give you more quality time to do other things. Live Smart. Enjoy Life. Should you encounter situations that have not been properly addressed in this Instruction Manual, please contact our Customer Service Center where a technician will be able to help you with your specific problem or question. For more information, please visit the ECOVACS ROBOTICS official website: HYPERLINK "http://www.ecovacs.com/" \h www. ecovacs.com The company reserves the right to make technological and/or design changes to this product for continuous improvement. Thank you for choosing WINBOT!
Contents 1. Important Safety Instructions ...........................................................................................................................................4 2. Package Contents and Technical Specifications ...........................................................................................................6 3. Operating WINBOT ..........................................................................................................................................................10 4. Maintenance .....................................................................................................................................................................19 5. Status Indicator Light and Sounds ................................................................................................................................23 6. Troubleshooting ..............................................................................................................................................................24 3 EN 1. Important Safety Instructions IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE SAVE THESE INSTRUCTIONS 1. This Appliance is not intended to be used by children under 8 or anyone lacking knowledge on proper use. Supervision may be necessary. Do not allow children to play with the Appliance. 2. Do not use the Appliance in extremely hot, cold or humid environments (below 0C/32F, above 40C/104F, above 65%
humidity). The Appliance can be used to clean outside windows if it is properly tethered to the Safety Pod, winds are calm, and it is not raining or snowing. 3. Do not leave the Appliance unattended when it is working. 4. For household use ONLY. Do not use the Appliance in commercial or industrial environments. 5. Do not use the Appliance on cracked glass, or glass with posters attached or raised dots on it. 6. Only use the Appliance as instructed by the instruction manual. Only use accessories recommended or supplied by the manufacturer. Only use the Rechargebale Battery and Power Adapter supplied by the manufacturer. 7. Please make sure your power supply voltage matches the power voltage marked on the Power Adapter. 8. Do not use the Appliance on a framed window with a frame smaller than 5mm (0.2 inches). 9. Do not use the Appliance on wet or greasy windows. 4 10. 1Store the Appliance away from heat and flammable materials. 11. Do not use the Appliance if it does not firmly attach to the glass or has visible signs of damage. 12. To reduce the risk of electrical shock, do not put the Appliance in water or other liquid. Do not place or store Appliance where it can fall or be pulled into a tub or sink. 13. Do not touch power plug or the Appliance with wet hands. 14. Do not charge the Appliance in extremely hot or cold environments, or it may affect battery life span. 15. When charging the Appliance, do not place it on other electrical appliances and keep it away from fire and liquid. 16. Take care not to damage the power cord. Do not pull on or carry the Appliance by the power cord, use the power cord as a handle, or put heavy weights on the power cord. Keep power cord away from hot surfaces. 17. Do not use with a damaged power cord or receptacle. Do not use the Appliance if it is not working properly, has been dropped, damaged, or come in contact with water. It must be repaired by the manufacturer or its service agent in order to avoid a hazard. 18. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent in order to avoid a hazard. 19. The plug must be removed from the receptacle before cleaning or maintaining the Appliance. 20. Do not unplug the Power Adapter by pulling on the power cord. 21. The Battery must be replaced by the manufacturer or its service agent in order to avoid a hazard. 22. The Battery must be removed and discarded according to local laws and regulations before disposal of the Appliance. EN 23. The Appliance must be disconnected from the receptacle before removing the battery for disposal of the Appliance. 24. Please dispose of used batteries according to local laws and regulations. 25. Do not incinerate the Appliance even if it is severely damaged. The battery can explode in a fire. 26. The Appliance must be used in accordance with the directions in this Instruction Manual. The manufacturer cannot be held liable or responsible for any damages or injuries caused by improper use. Class II Short-circuit-proof safety isolating transformer Switch mode power supply For indoor use only 1. Important Safety Instructions This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installedand used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) thisdevice must accept any interference received, including interference that may cause undesired operation. 5 EN 2. Package Contents and Technical Specifications 2.1 Package Contents WINBOT Power Adapter Instruction Manual Quick Start Guide Safety Pod with Batteries Remote Control with Batteries Cleaning Pads * 4 WINBOT Cleaning Solution Note: Figures and illustrations are for reference only and may differ from actual product appearance. Product design and specifications are subject to changes without notice. 6 EN 2. Package Contents and Technical Specifications 2.3 Product Diagram WINBOT 2.2 Specifications Model WA30 Working voltage 22.2V DC Rated power 60W Remote Control Rated output voltage 3V DC Power Adapter OH-1048A2701700U1-U Input 100-240V AC, 50/60Hz,1.5A Output 27V DC, 1.7A Note: Technical and design specifications may be changed in the course of continuous product improvement. Handle WINBOT Status Indicator Light/
START/ PAUSE Button Safety Pod Status Indicator Light Safety Pod Port Charging Port 7 EN 2. Package Contents and Technical Specifications Remote Control Cleaning Pad Velcro Cleaning Pad Driving Treads Direction Control Buttons Deep Cleaning Mode Button RESET Button Side Rollers Bottom WINBOT Status Indicator Light START/PAUSE Button Remote Control Pairing Button WINBOT Edge Detection Sensors Squeegee Fan Power Switch Bottom Safety Pod Status Indicator Light 8 EN Safety Pod Safety Pod Jack 2. Package Contents and Technical Specifications Battery Indicator Power Switch Safety Pod Pairing Button Battery Slot Quick Release Handle 9 EN 3. Operating and Programming 3.1 Notes Before Cleaning Do not use WINBOT on a framed window with a frame smaller than 5mm (0.2). WINBOT can clean framed or frameless glass, larger than 50cm x 50cm (19.7 x 19.7). If WINBOTs Status Indicator Light flashes RED, the battery requires charging. If the Battery Pods Battery Indicator Light flashes RED, the battery power is low, and the Safety Pod cannot work. Please change the battery. 10 EN 3. Operating and Programming If the window is covered with dirt, clean a small area on the glass before use and place WINBOT there. WINBOT can clean glass mounted at an angle but may not operate normally; in such a case, a person should be in the vicinity to assist should there be a problem. WINBOT can clean horizontally mounted glass but only when using the Direction Control Buttons on the Remote Control. WINBOT is intended to be used for maintenance cleaning on common windows. The product is not designed to replace heavy-duty or cleaning windows with heavy dust for the first time. Please refer to the glass manufacturer's care and cleaning instructions before using WINBOT on glass with an uneven surface, such as frosted, textured, patterned, or coated glass. The manufacturer cannot be responsible for damage due to improper use on these surfaces. Do not use WINBOT upside down. 11 EN 3. Operating and Programming 3.2 Using WINBOT 1 Assemble Power Adapter 3 Charge WINBOT 2 Power ON 4 Attach the Cleaning Pad Note: When WINBOT is charging, the Status Indicator Light flashes BLUE. When WINBOT is fully charged, WINBOT glows a continuous BLUE and then goes out. Note: Keep objects away from WINBOTs Fan to avoid blockage. 12 Note: Make sure the white side of the Cleaning Pad attaches to the Velcro. Make sure the Cleaning Pad does not cover the Squeegee or Edge Detection Sensors. The Cleaning Pad is not completely square and if attached improperly, covers part of the Squeegees. EN 3. Operating and Programming 5 Spray Cleaning Solution Note: It is recommended to use WINBOT with WINBOT Cleaning Solution from ECOVACS. Using tap water or other cleaners could have an adverse effect on cleaning performance. Using other cleaning solutions could potentially nullify the warranty. 1Step 2Step After spraying, wipe the bottom of WINBOT with a dry cloth. Note: The spray volume can be subject to the condition of dirt. 13 EN 3. Operating and Programming Warning: When using WINBOT to clean windows, Safety Pod must be used to guarantee the safety function of WINBOT. 6 Attach the Safety Pod 1Step 2Step 14 3Step 4Step 5Step EN 3. Operating and Programming 7 Start Cleaning 1Step
15 EN 3. Operating and Programming 2Step Make sure Safety Pod is attached at least 1.6 meters above ground, and the robot is suggested to be placed within an 1-meter radius of Safety Pod. 3Step
Note: WINBOT has successfully attached to the window when the WINBOT Status Indicator Light glows a continuous BLUE and beeps. Note: Please ensure there is a 15cm (5.9) clearance between the glass and obstacles in the room like curtains or furniture. Note: The Fan does not start until Safety Pod is firmly pressed on the glass and keep it away from hair or any debris.. Warning: If WINBOT is being used to clean an inside or outside windon, ALWAYS press Safety Pod FIRMLY on the INSIDE window. Make sure the Safety Pod is attached and securely in place. The length of the Safety Pod line is 2.5m. It is suggested to place the Safety Pod on the top corner of the window to ensure 1.6m above ground if the window is smaller. 16 EN AUTO Cleaning Mode 3. Operating and Programming Deep Cleaning Mode This mode is applicable for glass of more concentrated dirt or dust. 4Step This is the most commonly used mode and is good for regular cleaning. OR 9 Pause Note: WINBOT automatically chooses the suitable cleaning path in N or Z Cleaning Mode depending on the shape of the window. Note: Direct WINBOT to move using the Direction Control Buttons on the Remote Control when Paused. WINBOT cleans when the Direction Control Buttons are used. Note: Avoid moving WINBOT manually when it is cleaning or paused to ensure cleaning efficiency. 17 EN 3. Operating and Programming 10 Stop When WINBOT completes its cleaning cycle, it returns to the place it started and beeps. 1Step Note: Remove WINBOT from the window after the fan stops working. Polish away any marks left on the glass from the robots removal with a dry cloth If you want to stop the WINBOT during cleaning, please first press Start/Pause Button once to pause WINBOT and then press and hold this button for more than 5 seconds to stop WINBOT.. 3Step 4Step 2Step 18 Note: If WINBOT has a problem and the indicator Light flashes RED, it can be reset by pressing the RESET Button on the Remote Control. See Troubleshooting for details. EN Before performing cleaning and maintenance on WINBOT, Power OFF WINBOT and disconnect it from the Power Adapter. 4.1 Cleaning Pad 4.2 Fan, Sensors and Squeegee 4. Maintenance Fan Side Rollers Wash with mild detergent . Do NOT use a wet Cleaning Pad on WINBOT or it may slip on the window. Washing the Cleaning Pad regularly can extend its service life. If the Cleaning Pad becomes worn or no longer fits exactly within the Velcro area, replace it with a new one to achieve best cleaning performance. 19 EN 4. Maintenance Edge Detection Sensors 4.3 Driving Treads 1Step 2Step Inspect the Driving Treads by using the Direction Control buttons on the Remote Control. Stop the Driving Treads if dirt is seen on the Treads. Squeegee 20 EN 4Step 4. Maintenance 4.4 Safety Pod Note: Remove the Safety Pods battery if the robot will not be used for a long time. In case of battery leakage, please remove the battery and dispose of it according to local laws and regulations. 21 EN 4. Maintenance 4.5 Regular Maintenance To keep WINBOT running at peak performance, perform the maintenance and replacement according to the following frequency. Robot WINBOT Robot Part Cleaning Pad Fan Side Rollers Maintenance Frequency Replacement Frequency After each use Every 40 washings Edge Detection Sensors After each use
/
Squeegees Driving Treads Note: ECOVACS manufactures various replacement parts and assemblies. Please contact Customer Service for more information on replacement parts. 22 EN 5. Status Indicator Light and Sounds Indicator Description WINBOT Status Indicator Light flashes BLUE WINBOT Status Indicator Light glows a continuous BLUE 1. WINBOT is charging. 2. WINBOT has been paired with Safety Pod already and ready to be placed on the glass. 1. WINBOT has successfully adhered itself to the glass and is ready to clean. 2. The Safety Pod is in preparation. WINBOT Status Indicator Light flashes RED The robots battery is low. Charge WINBOT as described in Section 3.2. WINBOT Status Indicator Light glows a continuous RED Please refer to Section 6, Troubleshooting, for details. Safety Pod Status Indicator Light flashes GREEN Safety Pod Status Indicator Light glows a continuous GREEN The Safety Pod is not prepared to be pressed onto the glass:
1.The Safety Pod Jack is not inserted into WINBOT. 2.The Safety Pod is not paired with WINBOT. 3.The Safety Pod is not attached to the glass safely and firmly. 4.The Safety Pod is pairing with WINBOT. The Safety Pod is working normally. WINBOT can start working. Safety Pod Status Indicator Light flashes RED The Safety Pods battery is low. Replace the battery as described in Section 3.2. Safety Pod Status Indicator Light glows a continuous RED Please refer to Section 6, Troubleshooting, for details. Battery Indicator glows a continuous GREEN The Safety Pods battery is sufficient. WINBOT Safety Pod Battery Indicator flashes RED The Safety Pods battery is low. Please replace the battery as described in Section 3.2. 23 EN 6. Troubleshooting No. Malfunction Possible Causes Solutions 1 The robots fan does not work Safety Pod malfunction When WINBOT is cleaning, only the START/
PAUSE Button works on the Remote Control. The Remote Control is not paired with WINBOT.
(WINBOT arrives from the factory paired with its Remote Control. If the Remote Control becomes un-paired or is replaced, it can be re-paired.) 2 Remote Control does not work Check the Safety Pod Status Indicator Light on the WINBOT, and refer to Section 5 for details. Pause WINBOT by pressing the START/PAUSE button on the robot or Remote Control. Other buttons on the Remote Control will function when WINBOT is paused. Power ON WINBOT. Press and hold START/PAUSE Button on WINBOT and Pairing button on the Remote Control at the same time. Pairing is complete when START/PAUSE Button blinks RED and BLUE beeps. WINBOT Status Indicator Light glows a continuous RED. Press and hold RESET on the Remote Control to initialize WINBOT and then the remote control functions. The batteries are not installed in the Remote Control or need to be changed. Install or replace the batteries in the Remote Control. 24 EN 6. Troubleshooting No. Malfunction Possible Causes Solutions The Cleaning Pad is attached incorrectly and is covering the fan or the Edge Detection Sensors. Remove the Cleaning Pad and re-attach it making sure it is placed exactly within its Velcro area and does not cover the fan or the Edge Detection Sensors. Edge Detection Sensor malfunction. 3 WINBOT Status Indicator Light flashes BLUE after the product is placed on the glass. Fan malfunction. Glass is too dirty for WINBOT to adhere properly. A. Remove the Cleaning Pad and re-attach it making sure it will not cover or affect the Edge Detection Sensors. B. Clean the Edge Detection Sensors as described in section 4. C. If the problem persists, please contact Customer Service. A. Clean the Fan as described in section 4. B. If the problem persists, please contact Customer Service. Clean a small area on the glass before using and placing WINBOT there, or clean the window by hand first and use WINBOT for regular cleaning after that.
* WINBOT is intended to be used for maintenance cleaning on common windows. The product is not designed to replace heavy-duty or windows with heavy dust for the first time. 25 EN 6. Troubleshooting No. Malfunction Possible Causes Solutions 4 WINBOT Status Indicator Light of the product glows a continuous RED WINBOT has moved over a problem area and is losing suction. Edge Detection Sensor are dirty. A. Press the RESET Button on the Remote Control. Use the Direction Control buttons on the Remote Control to move WINBOT away from the problem area and at least 10cm/4 from window corners and obstacles. Restart WINBOT. B. Check if WINBOT meets an obstacle of window handle. Press the RESET Button on the Remote Control, and then use the Direction Control Buttons to direct WINBOT to clean around the area around the handle. Wipe the Edge Detection Sensors clean as described in section 4. If the problem persists, please contact Customer Service. The Safety Pod is not paired with WINBOT. WINBOT arrives from the factory paired with its Safety Pod. If the Safety Pod becomes un-
paired or is replaced, it can be re-paired. Power ON WINBOT. At the same time, press and hold START/PAUSE Button on WINBOT and Pairing button on the Safety Pod. Pairing is complete when Safety Pod Status Indicator Light blinks RED and GREEN and beeps. 5 Safety Pod Status Indicator Light of the product glows a continuous RED Safety Pod is losing its suction. Remove the Safety Pod, and re-press it onto the glass until the Safety Pod Status Indicator Light glows a continuous GREEN. Safety Pod is in Sleep Mode. Power off the Safety Pod then Power it on. Safety Pod Jack is not connected with WINBOT Safety Pod Port. Insert the Safety Pod Jack into the Port as described in section 3.2 26 EN No. Malfunction Possible Causes Solutions 6. Troubleshooting 6 WINBOT moves in an irregular pattern during cleaning. There is too much dirt and debris on the window. 7 WINBOT is stuck, and cannot move, be controlled by the Remote Control, or be reset by pressing RESET. Insufficient suction or Edge Detection Sensor signal abnormity. 8 WINBOT will not charge. WINBOT is not powered ON. A. Spray additional Cleaning Solution on the Cleaning Pad. B. Clean the Driving Treads as described in section 4. C. Replace the Cleaning Pad and restart the cleaning cycle. D. Use the Remote Control to control the cleaning by pressing Direction Buttons.
* WINBOT is intended to be used for maintenance cleaning on common windows. The product is NOT designed to replace heavy duty or first time cleaning. Press the RESET Button on the Remote Control and then press and hold it until the WINBOT Status Indicator Light glows a continuous BLUE or Safety Pod Status Indicator Light glows a continuous GREEn to switch WINBOT to Manual Override Mode. In Manual Override Mode, the Direction Control Buttons on the Remote Control are activated. Use the Direction Control Buttons to move WINBOT to a position away from edges and where you can safely reach it. Remove WINBOT from the window and power OFF. Power ON and restart.
*When using the Manual Override Mode, do not leave WINBOT attached to the glass unattended. If the problem persists, please contact Customer Service. Move the robots Bottom Power Switch to the ON position. 27 EN Ecovacs Robotics Co., Ltd No. 18 You Xiang Road, Wuzhong District, Suzhou City, Jiangsu Province, P.R.China WA30-EN01-IM2017R00