FCC ID: 2AJMW-KBMS25K Wireless Keyboard

KBMS250K KBMS250M IMPORTANT SAFETY INSTRUCT IONS

Read these instructions carefully.

Keep these instructions in a safe place and follow all instructions.

Do not use this product near water.

Cleaning: Do not use liquid cleaners or aerosol cleaners. Clean only with a dry damp cloth.

Do not place near any heat sources such as radiators, heat registers, stoves, or other apparatuses (including amplifiers) that produce heat.

Only use attachments/accessories specified by the manufacturer.

Refer all servicing to qualified service personnel. Servicing is required when the product has been damaged in any way, such as objects have fallen into the product, does not operate normally, or has been dropped. FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. WARNING Changesormodificationstothisunitnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidtheuser'sauthority to operatetheequipment. IC Warning This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. RF exposure statement:

The equipment complies with IC Radiation exposure limit set forth for uncontrolled environment. Cet appareil contient des metteurs / rcepteurs exempts de licence conformes aux RSS

(RSS) d'Innovation, Sciences et Dveloppement conomique Canada. Le fonctionnement est soumis aux deux conditions suivantes:

(1) Cet appareil ne doit pas causer d'interfrences.

(2) Cet appareil doit accepter toutes les interfrences, y compris celles susceptibles de provoquer un fonctionnement indsirable de l'appareil. Tout changement ou modification non expressment approuv par la partie responsable de la conformit pourrait annuler l'autorit de l'utilisateur utiliser l'quipement. Dclaration d'exposition RF:

L'quipement est conforme la limite d'exposition aux rayonnements IC tablie pour un environnement non contr ThisdevicecomplieswithCanadianICES-003andRSS-210 FCC ID: 2AJMW-KBMS25K FCC ID: 2AJMW-KBMS25M IC: 20174-KBMS25K IC: 20174-KBMS25M Thank you for your purchase. E-1 INSTALLING BATTERIES E-2 1. Remove the top mouse cover 2. Remove the USB dongle 3. Insert 1 x AA size battery (not included) in the correct polarity position and replace the mouse cover 4. Remove the battery compartment cover on the back side of the keyboard 5. Insert 2 x AAA size batteries (not included) in the correct polarity position and replace the battery cover CAUTION 1. Do not mix old and new batteries. 2. Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries. 3. If the unit is not to be used for an extended period of time, remove the batteries. Old or leaking batteries can cause damage to the unit and may void the warranty. 4. Do not dispose of batteries in fire, batteries may explode or leak. BATTERY DISPOSAL Do not dispose of the batteries in normal household waste. For disposal and recycling, please contact your local waste management authorities. CONNECTING THE KEYBOARD AND MOUSE 1. Turn on your desktop computer or laptop 2. Insert the USB dongle into an available USB port on your desktop computer or laptop 3. Your plug-and-play keyboard and mouse will be ready to use E-3 Need help? Please call us. If you encounter any difficulties with this product, please call or email us and our representatives will be ready to help you. Toll free: 1-800-593-6669 (Monday to Friday: 9am 5pm EST) Email: support@borne-lifestyle.com Thank you for your purchase. We want you to start enjoying your product. LIMITED WARRANTY Warning: Some Products may contain components that are small enough to be swallowed. Keep out of the reach of children. Before returning your Product for service under this Warranty, (i) please read the instruction manual carefully and visit our website at www.borne-lifestyle.com for product updates and extended support documentation (e.g., Frequently Asked Questions, Common Troubleshooting Guides); (ii) please contact Edco Electronics Support if you are still having trouble with your Product. Subject to the terms and conditions herein, Edco Electronics warrants to the original purchaser of the Product (Customer) that the Product will be free from defects in material or workmanship under normal, noncommercial use (Defects) for a period of 1 year. Warranty Period encompasses separate Coverage Periods for Parts and Labor, with each Coverage Period to begin from the original date of Customer purchase. Parts are covered for a period of 1yr. Labour is covered for 90 days. If Customer returns a defective Product during the applicable Warranty Period, Edco Electronics will, at its option during the specified Coverage Periods for Parts and Labor (as applicable), either: (i) repair the Product or (ii) replace the Product with a new or refurbished Product, in either case free of charge to Customer for Parts and/or Labor (as applicable) during the specified Coverage Period only, and excluding applicable shipping charges for which the Customer is responsible. The foregoing states the Customers exclusive remedy and Edco Electronics sole liability for breach of the limited warranty contained herein. This Warranty specifically excludes any Product (or, as applicable, any component thereof) that has Defects resulting from: (a) any neglect or misuse by a Customer, an accident, improper application, violation of operating instructions for the Product, any other Customer-induced damage, or the alteration or removal of any Product serial number; (b) any modification or repair to Product by any party other than Edco Electronics or a party authorized in writing by Edco Electronics; (c) any damage to Product due to power surges, incorrect electrical voltage, misconnection to any device, or malfunction of any device used with the Product; (d) cosmetic damage to the Product caused by normal wear and tear; (e) shipping damage that occurs while the Product is in transit; (f) damage caused by heat sources, sunlight, electromagnetic conditions, or other climatic conditions; or (g) any acts of God. Product is sold to Customer for personal, non-commercial use only. Product is not warranted for Customers commercial or rental use. In addition, Product is not warranted against failure, and should not be used by Customer for any application where (i) there is a risk that any data stored on Product will be breached or otherwise compromised, or (ii) the data stored on Product is relied upon for medical or lifesaving applications. Edco Electronics expressly disclaims any warranty for any of the foregoing uses to the fullest extent permitted by law. Customer assumes any and all risks associated with such uses of Product, and agrees to indemnify Edco Electronics for any damages claimed against Edco Electronics for such uses. This Warranty specifically and expressly excludes any Product that is purchased by Customer as a floor or display model. Any such Product is purchased by Customer AS IS and Edco Electronics disclaims any Warranties, express or implied, in relation thereto. EXCEPT FOR THE EXPRESS WARRANTIES STATED ABOVE AND TO THE MAXIMUM EXTENT PERMITTED BY LAW, THE PRODUCT IS PROVIDED AS IS, AND EDCO ELECTRONICS DISCLAIMS ALL OTHER WARRANTIES, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF (I) MERCHANTABILITY, (II) FITNESS FOR A PARTICULAR PURPOSE, OR (III) E-4 NON-INFRINGEMENT OF THIRD PARTY RIGHTS. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT WILL EDCO ELECTRONICS BE LIABLE TO CUSTOMER OR ANY THIRD PARTY FOR ANY INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL, EXEMPLARY OR PUNITIVE DAMAGES, INCLUDING, WITHOUT LIMITATION, ANY LOST PROFITS OR REVENUES, LOSS OR INACCURACY OF ANY DATA OR COST OF SUBSTITUTE GOODS, REGARDLESS OF THE THEORY OF LIABILITY (INCLUDING NEGLIGENCE). ADDITIONALLY, EVEN IF EDCO ELECTRONICS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, EDCO ELECTRONICS AGGREGATE LIABILITY TO CUSTOMER FOR ACTUAL DIRECT DAMAGES FOR ANY CAUSE WHATSOEVER SHALL BE LIMITED TO THE CUMULATIVE PRODUCT COSTS PAID BY THAT CUSTOMER FOR THE PRODUCT CAUSING SUCH DAMAGES, IF ANY. This Warranty gives Customer specific rights, and Customer may also have other rights that vary from jurisdiction to jurisdiction. To obtain Warranty service, Customer must call Edco Electronics Support prior to making a Product Return. Customer must include with Product Return the following items: (i) a dated sales receipt that indicates the place of purchase, model number of Product, and amount paid; (ii) a detailed description of Customers problem with Product; (iii) Customers full name, phone number, and return address, and; (iv) a money order for any applicable shipping costs made out to Edco Electronics Inc. to cover return shipping charges to US and Canadian destinations only. Edco Electronics will not make return shipments to a P.O. Box. For shipping to international addresses, actual freight will be charged to Customer. Failure to enclose any of these items may delay the processing of your Warranty claim. Return your Product freight-prepaid in its original packaging, or packaging that affords an equal measure of protection. Please allow 4 to 6 weeks for the processing of your claim. Edco Electronics Inc. 8484 Esplanade, Montreal, Quebec H2P 2R7 Canada Toll Free: 1-800-593-6669 (Monday to Friday: 9am to 5pm EST) Email: support@borne-lifestyle.com E-5

Page 1 of 1 FCC ID: 2AJMW-KBMS25K LABEL AND LOCATION Wireless Keyboard Model: KBMS250K FCC ID: 2AJMW-KBMS25K

(Size: L: 2.0cm x W: 1.5cm) Label Location Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: webmaster@lcs-cert.com | Web: www.lcs-cert.com Scan code to check authenticity

C5266091_X24_Ed.2 Edco Electronics Inc. Attestation Statements TO:

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules for covered telecommunications equipment and video surveillance equipment produced by entities identified on the Commissions Covered List1, which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) that prohibit equipment authorization Applicant Company name: Edco Electronics Inc. Grantee code: 2AJMW FCC ID: 2AJMW-KBMS25K Contact Name: Jonathan Lee Address:

Telephone No:

Fax No:

Email: jonathan@borne-lifestyle.com 8484 Avenue de l'Esplanade Montreal, Quebec H2P 2R7 Canada 1-438-738-5163 1-514-858-1588 i. ii.

[Edco Electronics Inc.] (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification.

[Edco Electronics Inc.] (the applicant) certifies that, as of the date of the filing of the application, the applicant [is not] (as a specifically named entity or any of its subsidiaries or affiliates) identified on the Covered List as an entity producing covered equipment. The applicant must sign this certification.

[Edco Electronics Inc.] (the applicant) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered List as an entity producing coveredequipment . Date: 2023/05/31 Applicants Name: Jonathan Lee Title: Director of Product Development Signature 1 The Commissions Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commissions website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes covered equipment. https://www.fcc.gov/supplychain/coveredlist 1/1

Edco Electronics Inc. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Confidentiality FCC ID: 2AJMW-KBMS25K To Whom It May Concern, C5266091_X10_Ed.2 Date: 2023-05.31 Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality No No No No No NOTE 1 NOTE 1 No No Short-Term Confidentiality NOTE 2 No No No No No No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. 1/1 C5266091_X10_Ed.2 Sincerely, Signature:

Name: Jonathan Lee Title: Director of Product Development 2023.05.31 1/1

C5266091_X8_Ed.1 Edco Electronics Inc. Letter of Authorization Company: Edco Electronics Inc. Address: 8484 Avenue de l'Esplanade Montreal, Quebec H2P 2R7 Canada Product Name: Wireless Keyboard Model Number: KBMS250K FCC Identifier: 2AJMW-KBMS25K We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Jonathan Lee Date: 2023.05.31 Title: Director of Product Development Signature of applicant:

1/1

Edco Electronics Inc. Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 U.S. Agent Designation 5/31/23 Edco Electronics Inc. acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought

(FCC ID: 2AJMW-KBMS25K):

Contact Name: Samuel Weiss Company of U.S. agent: Molo Import Export LLC Physical U.S. address of agent: 2334 Crystal Mile CT, Toms River, NJ, 08755, USA FRN of U.S. agent: 0033490996 Email address of U.S. agent: 8259781@gmail.com Molo Import Export LLC acknowledges their obligation to accept service of process on behalf of Edco Electronics Inc. Edco Electronics Inc. with the FRN 0025849605 accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(d)(7). Sincerely, Signature Michael Choi Director of Product Development Edco Electronics Inc. Signature Samuel Weiss Manager Molo Import Export LLC 4 0 V

, U

) 7

) d

1 1 9 2 _ t n e g A _ S U

l e d o m

_ 8 4 The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB.