FCC ID: YZKEAP101N 802.11ax Dual-Band Enterprise Access Point

Quick Start Guide 802.11ax Dual-Band Enterprise Access Point EAP101 Package Contents 1 2 3 4 5 6 7 EAP101 access point 1. 2. AC power adapter with international socket converters 3. Mounting bracket accessory 4. Mounting bracket security screw Screw kit4 screws and 4 plugs

(Optional) Console cableRJ-45 to DB-9 5. 6. 7. QR code card Overview 1 2 3 4 5 6 1. 12 VDC power input 2. Restart/Reset button:

7 A quick press restarts the system. Press and hold for 5 seconds resets to factory defaults. 3. USB 2.0 port (reserved for future use) 4. Console port 5. 6. Uplink(PoE) Port: 2.5Gbps connection to 802.3at PoE LAN device. 7. LAN1/LAN2 Ports: 1Gbps connection to LAN devices. System LED Indicators:

2.4G: On (radio on), Blinking (traffic) 5G: On (radio on), Blinking (traffic) Status: On (power OK), Blinking (boot up) 8 8. Kensington lock slot Warning: For indoor use only. The access point, AC power adapter, and all connected cables are not for outdoor use. Installation b. Mounting on a Suspended Ceiling T-Bar Mount the AP 1 a. Mounting on a Wall 1 2 1. At the installation location on the wall, use the mounting bracket to mark four holes for the wall plugs and screws (included in the screw kit). Drill four holes for the wall plugs, and then insert the plugs and tap them flush with the wall surface. Use the four screws to secure the bracket to the wall. 2. With its ports facing down, slide the AP down onto the bracket until it snaps into its secured position. 1 2 3 3 1. Slide the bracket accessory onto the base of the AP until it clicks into its locked position. 2. Use the included security screw to secure the bracket to the AP. 3. Position the ceiling-mount clip holders on either side of the T-bar, and then turn the AP until the two clips lock it to the T-bar. Note: The AP mounting supports two different sizes of suspended ceiling T-bars. The position illustrated above is for 24.5 mm bars. Use the position at a 90 degrees angle for 15 mm bars. www.edge-core.com 1 E032021-CS-R01 c. Mounting on a Ceiling Without T-Bars 3 Check AP LEDs Quick Start Guide 1 2 1. At the installation location on the ceiling, use the mounting bracket to mark four holes for the plugs and screws (included in the screw kit). Drill four holes for the plugs, and then insert the plugs and tap them flush with the ceiling surface. Use the four screws to secure the bracket to the ceiling. 2. Slide the AP onto the bracket until it snaps into its secured position. 2 Connect Cables a. Connect LAN Cables 1 2 1. Connect Category 5e or better cable to the Uplink(PoE) 2.5G RJ-45 port. When connected to a PoE source, the Uplink(PoE) port connection provides power to the unit.

(Optional) Connect a local LAN switch or computer to the LAN1 or LAN2 1000BASE-T RJ-45 ports. 2. b. (Optional) Connect AC Power Adapter 1 1 2 1. 2.4G and 5G LEDs on green for radio enabled. 2. Power/Status LED on green for normal operation. 4 Connect to the Web User Interface 1. Connect a PC directly to the APs LAN1 or LAN2 port. 2. Set the PC IP address to be on the same subnet as the AP LAN port default IP address. (The PC address must start 192.168.2.x with subnet mask 255.255.255.0.) Enter the APs default IP address of 192.168.2.1 into the web browser address bar. Log in to the web interface using default settings:

Username = admin Password = admin 3. 4. Note: To connect to the web interface using the Uplink(PoE) port, the IP address is automatically assigned through DHCP by default. If a DHCP server is unreachable, the Uplink(PoE) port reverts to a fallback IP address of 192.168.1.10. 1. When not connected to a PoE source, connect the AC power adapter to the DC power jack on the AP and then plug the adapter into a nearby AC power source. Note: To reset the AP to factory default settings, press and hold down the APs Restart/Reset button for 5 seconds. 2 Safety and Regulatory Information the limits for a 15 of the FCC Rules. These limits FCC Class B This equipment has been tested and found to comply with Class B digital device, pursuant to Part are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

guarantee that interference will Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help FCC Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. the FCC Rules. Operation is subject For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This operated with minimum distance 24 cm between the radiator and your body. equipment should be installed and Professional Installation Instructions 1. Installation personnel This product is designed for specific by qualified personnel who have regulations. A general user shall not attempt to install or modify the equipment configuration. knowledge of RF and its related applications and should be installed 2. Installation location To meet regulatory RF exposure requirements, this product shall be installed at a location where, during normal operations, the radiating antenna is at least 23 cm away from any nearby persons. 3. External antenna Use only the antennas which have Using non-approved antenna(s) is prohibited and may produce unwanted spurious or excessive RF transmitting power which may lead to a violation of FCC limits. been approved by the applicant. 4. Installation procedure Please refer to this equipment's user manual for the procedure details. 5. Warning The installation position must be carefully selected so that the final output power does not exceed the regulations. Violation of output power regulations could lead to serious federal penalties. limit set forth in relevant Quick Start Guide Industry Canada This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-

exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil contient des metteurs /

sont conformes au (x) RSS (s) exempts et Dveloppement conomique Canada. Lopration est soumise aux deux conditions suivantes:

rcepteurs exempts de licence qui de licence dInnovation, Sciences

(1) Cet appareil ne doit pas provoquer dinterfrences.

(2) Cet appareil doit accepter toute interfrence, y compris les interfrences susceptibles de provoquer un fonctionnement indsirable de lappareil. The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes mmes canaux. de satellites mobiles utilisant les IMPORTANT NOTE:

IC Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 28 cm between the radiator & your body. Cet quipement est conforme aux limites dexposition aux rayonnements Cet quipement doit IC tablies pour un environnement non contrl. tre install et utilis avec un minimum de 28 cm de distance entre la source de rayonnement et votre corps. CE Statement This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This operated with minimum distance 24 body. equipment should be installed and cm between the radiator and your The device is restricted to indoor 5150 to 5350 MHz frequency range. use only when operating in the All operational modes:

2.4 GHz: 802.11b, 802.11g, 802.11n (HT20), 802.11n (HT40), 802.11ac (VHT20), 802.11ac (VHT40), 802.11ax (HE20), 802.11ax (HE40) 5 GHz: 802.11a, 802.11n (HT20), 802.11n (HT40), 802.11ac

(VHT20), 802.11ac (VHT40), 802.11ac (VHT80), 802.11ax (HE20), 802.11ax (HE40), 802.11ax (HE80) BLE 2.4 GHz: 802.15.1 The frequency and maximum transmitted power limit in EU are listed as below:

2412-2472 MHz: 20 dBm 5150-5350 MHz: 23 dBm 5500-5700 MHz: 30 dBm Professional installation is required 15.19(a)(3) Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. 3 AT BE BG CH CY CZ DE DK EE EL FR HR HU IE ES IS FI IT LI LT LU LV MT NL NO PL PT RO SE SI SK TR UK The abbreviations of the countries, as prescribed in above table, where any restrictions on putting into service or any requirements for authorization of use exist. CE Mark Declaration of Conformance for EMI and Safety (EEC) This information technology equipment is in compliance with the Directive 2014/53/EU and Directive 2014/35/EU. 2.4 GHz Radio IEEE 802.11b/g/n/ax 5 GHz Radio IEEE 802.11a/ac/n/ax Bluetooth Radio IEEE 802.15.1 The Declaration of Conformity (DoC) can be obtained from www.edge-core.com -> support -> download. Radio Frequencies Japan VCCI Statement Quick Start Guide Hardware Specifications AP Chassis Size (WxDxH) 195 x 195 x 39 mm (7.68 x 7.68 x 1.54 in.) Weight 0.65 kg (1.435 lb) Temperature Operating: 0 C to 50 C (32 F to 122 F) Storage: -40 C to 70 C (-40 F to 158 F) Humidity Operating: 5% to 95% (non-condensing) Network Interfaces Ports Uplink(PoE) RJ-45 Port: 2.5G, PoE PD LAN1 RJ-45 Port: 1000BASE-T LAN2 RJ-45 Port: 1000BASE-T 2.4 2.4835 GHz (US, Canada, ETSI) 5.15 5.25 GHz (lower band) US/Canada, Europe 5.725 5.825 GHz (upper band) US/Canada Power Specifications PoE Input Power 22.4 W max, 48 VDC55 VDC;

802.3at-compliant AC Power Adapter AC Input: 100240 VAC, 50-60 Hz DC Output: 12 VDC, 2 A Regulatory Compliances Radio EN300 328 V2.2.2 (2019-07) EN301 893 V2.1.1(2017-03) 47 CFR FCC Part 15.247 47 CFR FCC Part 15.407 NCC LP002 MIC certification Rule, Article 2 Paragraph 1 Item 19 MIC certification Rule, Article 2 Paragraph 1 Item 19-3 and 19-3-2 EN 301 489-1 V2.1.1 (2017-02) EN 301 489-17 V3.1.1 (2017-02) EN 55032:2015 EN 55024:2010/A1:2015 AS/NZS CISPR 32:2015, Class B 47 CFR FCC Rules and Regulations Part 15 Subpart B, Class B Digital Device CNS 13438 Low Voltage Directive (2014/35/EU, formerly 2006/95/EC, formerly 73/23/EEC) CNS 14336-1 IEC/EN 62368-1, IEC/EN 60950-1 Taiwan RoHS CNS 15663 5 GHz band (W52, W53): Indoor use only NCC Statement (Taiwan) NCC MPE

(MPE) 1mW/cm2 0.32982mW/cm2 24cm Emissions Warnings and Cautionary Messages Safety Warning: This product does not contain any serviceable user parts. Warning: Installation and removal of the unit must be carried out by qualified personnel only. Warning: When connecting this device to a power outlet, connect the field ground lead on the tri-pole power plug to a valid earth ground line to prevent electrical hazards. Caution: Wear an anti-static wrist strap or take other suitable measures to prevent electrostatic discharge when handling this equipment. Caution: Do not plug a phone jack connector in the RJ-45 port. This may damage this device. Caution: Use only twisted-pair cables with RJ-45 connectors that conform to FCC standards. 4

Ent: SRE 30 gf [Model : EAP101 Qooxrverryyzew &S Input: 12V==2; 2A 30x12mm No printing Made in XXXXX __ 246000002769H RBO FCC ID: YZKEAP101N |

a 27052-EAP101N '

037019 SC z &

RoHS

Edgecore Networks Corporation No. 1, Creation Rd. Ill, Science Park Hsin Chu 30077, Taiwan Class II Change Letter Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To Whom It May Concern:

Request for Class || Permissive Change FCC ID: YZKEAP101N / Grant Date: 04/06/2021 Pursuant to CFR 2.1043, Edgecore Networks Corporation hereby requests a Class II Permissive Change. Modification:

Adding U-NII-2A and U-NII-2C bands (5250~5350 MHz, 5470%5725 MHz) for this device. There is no change in hardware or in existing RF relevant portion. The product enables U-NII-2A and U-NII-2C bands via Firmware by factory. There is no any software that can be modified by end-user. Respectfully, Applicants company name : Edgecore Networks Corporation Science Park Hsin Chu 30077, Taiwan Applicants company address : No. 1, Creation Rd. Signature ;

Landa Sun ae Name and Job Title : Linda Sung / PM E-Mail : linda_sung@edge-core.com Tel : 886-3-5638888 Fax : 886-3-6686111 Date: 2022/1/12

Edgecore Networks Corporation No. 1, Creation Rd. Ill, Science Park Hsin Chu 30077, Taiwan Confidential Letter Date: 2022/1/12 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidenti FCC ID : YZKEAP101N To Whom It May Concern:

Long Term Confidentialit Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby respectfully request confidential treatment of information accompanying this application as outlined below:

@ Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The pub!

disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We understand that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Respectfully, Applicants company name : Edgecore Networks Corporation Applicants company address : No, 1, Creation Rd. Ill, Science Park Hsin Chu 30077, Taiwan Signature Lowden haan Name and Job Title : Linda Sung / PM E-Mail : linda_sung@edge-core.com Tel : 886-3-5638883 Fax : 886-3-6686111

Edgecore Networks Corporation No. 1, Creation Rd. Ill, Science Park Hsin Chu 30077, Taiwan Power of Attorney Date: 2022/1/12 Dear Sir,

| hereby have entrusted the following person to be a proxy regarding application for Type Certification. Sporton International Inc. Address : No.8, Lane 724, Bo-ai St., Jnubei City, HsinChu County 302, Taiwan, R.O.C. Name : Leo Huang Job Title : Manager e-mail : Leohuang@sporton.com.tw lam therefore responsible for the contents of the application. FCC ID: YZKEAP101N Respectfu Applicants company name : Edgecore Networks Corporation Applicants company address : No. 1, Creation Rd. Ill, Science Park Hsin Chu 30077, Taiwan Signature F Lands weet. Name and Job Title : Linda Sung / PM E-Mail : linda_sung@edge-core.com Tel : 886-3-56388838 Fax : 886-3-6686111

Edgecore Networks Corporation No. 1, Creation Rd. Ill, Science Park Hsin Chu 30077, Taiwan TPC Declaration Letter Date: 2022/1/12 FCC ID : YZKEAP101N To Whom It May Concern:

We, Edgecore Networks Corporation, declare that the device supports the TPC function in final F/W when EUT is sold to FCC market. Respectfully, Applicants company name : Edgecore Networks Corporation Applicants company address : No. 1, Creation Rd. Ill, Science Park Hsin Chu 30077, Taiwan Signature Lewd. Sunt Name and Job Title : Linda Sung / PM

: linda_sung@edge-core.com Tel : 886-3-5638888 Fax : 886-3-6686111

Edgecore Networks Corporation No. 1, Creation Rd. Ill, Science Park Hsin Chu 30077, Taiwan Confidential Letter Date: 2021/3/18 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID : YZKEAP101N To Whom It May Concern:

Long Term Confidentialit Pursuant to Sections 0.457 and 0.459 of the Commission's Rules, we hereby respectfully request confidential treatment of information accompanying this application as outlined below:

e@ Block Diagrams e@ Schematics e Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We understand that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Respectfully, Applicant's company name : Edgecore Networks Corporation Applicant's company address : No. 1, Creation Rd. Ill, Science Park Hsin Chu 30077, Taiwan Signature ;

avd wt Name and Job Title : Linda Sung / PM E-Mail : linda_sung@edge-core.com Tel : 886-3-5638888 Fax : 886-3-6686111

Edgecore Networks Corporation No. 1, Creation Rd. Ill, Science Park Hsin Chu 30077, Taiwan Power of Attorney Date: 2021/3/18 Dear Sir,

| hereby have entrusted the following person to be a proxy regarding application for Type Certification. Sporton International Inc. Address : No.8, Lane 724, Bo-ai St., Jnubei City, HsinChu County 302, Taiwan, R.O.C. Name : Leo Huang Job Title : Manager e-mail : Leohuvang@sporton.com.tw 1am therefore responsible for the contents of the application. FCC ID: YZKEAP101N Respectfully, Applicant's company name : Edgecore Networks Corporation Science Park Hsin Chu 30077, Taiwan Applicant's company address : No. 1, Creation Rd Signature ;

Livden Sunt =

Name and Job Title : Linda Sung / PM E-Mail : linda_sung@edge-core.com Tel : 886-3-5638888 Fax : 886-3-6686111

Edgecore Networks Corporation No. 1, Creation Rd. Ill, Science Park Hsin Chu 30077, Taiwan Professional Installation Declaration Date: 2021/3/18 FCC ID : YZKEAP101N To Whom It May Concern:

Please be advised that due to the unique Market and function targeted by this product, this product will need special trained professional in configuring and installing the product. We hereby declare that the product will be distributed through controlled distribution channel which has special trained professional to install this product and will not be sold directly to the general public through retail store. Respectfully, Applicant's company name : Edgecore Networks Corporation Applicant's company address : No. 1, Creation Rd. lll, Science Park Hsin Chu 30077, Taiwan Signature os iat Name and Job Title : Linda Sung / PM E-Mail : linda_sung@edge-core.com Tel 1 886-3-5638888 Fax > 886-3-6686111

Edgecore Networks Corporation No. 1, Creation Rd. Ill, Science Park Hsin Chu 30077, Taiwan SDoC Attestation Letter Date: 2021/3/18 We Edgecore Networks Corporation, as the grantee of this project (FCC ID; YZKEAP101N / Brand Name: Edgecore / Model No.: EAP101), would like to declare that the composite portion has been authorized under the Supplier's Declaration of Conformity procedures (Sporton report No.:

FD0029 13-02, FCC designation number: TW1096). The final product shall consequently comply with the FCC rule applied for SDoC Procedure. Respectfully, Applicant's company name : Edgecore Networks Corporation Applicant's company address: No. 1, Creation Rd. Ill, Science Park Hsin Chu 30077, Taiwan Signature Y Tada we) Name and Job Title : Linda Sung / PM E-Mail : linda_sung@edge-core.com Tel : 886-3-5638888 Fax : 886-3-6686111