Handbook ECW5210-L Enterprise Access Point FCC CAUTION ECW-5210-L Enterprise Access Point ENGLISH Handbook This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device is restricted to indoor use when operated in the 5.15 to 5.25 GHz frequency range. FCC requires this product to be used indoors for the frequency range 5.15 to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems. IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. i ECW-5210-L Enterprise Access Point ENGLISH Handbook CE CAUTION Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive) for European Community, Switzerland, Norway, Iceland, and Liechtenstein Model: ECW5210-L For 2.4 GHz radios, the device has been tested and passed the requirements of the following standards, and hence fulfills the EMC and safety requirements of R&TTE Directive within the CE marking requirement. Radio: EN 300.328:
EMC: EN 301.489-1, EN 301.489-17, EMC: EN 55022 Class B, EN 55024:+ A1 + A2 including the followings:
EN 61000-3-2, EN 61000-3-3. EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-4-11 Safety: EN 60950-1 + A11, Caution:
This declaration is only valid for configurations (combinations of software, firmware, and hardware) provided and supported by Edgecore Networks Corporation. The use of software or firmware not provided and supported by Edgecore Networks Corporation. may result in the equipment no longer being compliant with the regulatory requirements. European standards dictate maximum radiated transmit power of 100mW EIRP and frequency range 2.400-2.4835 GHz. This equipment is intended to be used in all EU and EFTA countries. Taiwan NCC Statement NCC :
5.25 ~ 5.35 ii ECW-5210-L Enterprise Access Point ENGLISH Handbook Package Contents 1. Edgecore ECW5210-L x 1 2. Handbook x 1 3. Wall Mount Kit x 1 4. Ceiling Mount Kit x 1 5. DC Extension plug x 1 It is recommended to keep the original packing material for possible future shipment when repair or maintenance is required. Any returned product should be packed in its original packaging to prevent damage during delivery. Preface Edgecore ECW5210-L is a high-end, dual radio 802.11 b/g/n + ac MIMO Access Point (AP) with the best performance for business and industrial applications and is compliant with the latest industrial wireless security standards that are required in the tightly secured enterprise network environments. ECW5210-L makes the wireless communication fast, secure and easy. It supports business grade security such as 802.1X, and Wi-Fi Protected Access
(WPA and WPA2). The ECW5210-L supports multiple point-to-point wireless links to form wider wireless network coverage. ECW5210-L also features multiple ESSIDs with VLAN tags and multiple Virtual APs; great for enterprise applications, such as separating traffic from different departments using different ESSIDs. The PoE Uplink port is able to receive power from Power over Ethernet (PoE) sourcing devices. This Handbook provides instructions and reference materials to get you started with Edgecore ECW5210-L. 0 System Overview ECW-5210-L Enterprise Access Point ENGLISH Handbook ECW5210-Ls Front Panel ECW5210-Ls Rear Panel 1 2 LED Indicators An LED indicator is available to show the uplink status 12V 2.5 A Attach power adaptor here 3 Uplink (PoE) Port Offers uplink connection. This port can be used to connect to a controller, gateway, or directly to the Internet. 802.3at PoE is also supported 1 123 Hardware Installation ECW-5210-L Enterprise Access Point ENGLISH Handbook Please follow the steps mentioned below to install the hardware of ECW5210-L:
1. Place the ECW5210-L at the best location. a) The best location for ECW5210-L is usually at the center of your intended wireless network. Wall Mounting
- Secure wall-mount bracket on wall
- Attach the Access Point to the dedicated slots on the mounting bracket
- Turn the Access Point clockwise as illustrated to fasten AP 2 Ceiling Mount ECW-5210-L Enterprise Access Point ENGLISH Handbook
- Secure ceiling-mount bracket on ceiling
- Attach the Access Point to the dedicated slots on the mounting bracket
- Turn the Access Point clockwise as illustrated to fasten AP 3 ECW-5210-L Enterprise Access Point ENGLISH Handbook 2. Connect the ECW5210-L to your network device. Connect one end of the Ethernet cable to the Uplink port of ECW5210-L and the other end of the cable to a switch, a router, or a hub. ECW5210-L is then connected to your existing wired LAN network. 3. Power on the ECW5210-L. There are two ways to supply power over to ECW5210-L.
- ECW5210-L Uplink port is capable of receiving DC currents. Connect an IEEE 802.3at-compliant PSE device (e.g. a PoE-switch) to the Uplink port of ECW5210-L with the Ethernet cable.
- Connect a 12V/2.5A adaptor (optional) to the DC power jack. If needed, use the DC extension plug included. Now, the Hardware Installation is complete. Using a different power adapter may damage this system. To verify the wired connection between ECW5210-L and you switch / router / hub, please also check the LED status indicator of the respective network devices. 4 Getting Started ECW-5210-L Enterprise Access Point ENGLISH Handbook Edgecore ECW5210-L supports web-based configuration. When hardware installation is complete, ECW5210-L can be configured through a PC by using a web browser such as Mozilla Firefox 2.0 or Internet Explorer version 6.0 and above. The default values of LAN IP address and subnet mask of ECW5210-L are:
IP Address: 192.168.1.10 Subnet Mask: 255.255.255.0 Steps:
1. To access the Web Management Interface, connect the administrator PC to the Uplink port of ECW5210-L via an Ethernet cable. Then, set a static IP address on the same subnet mask as ECW5210-L in TCP/IP of your PC, such as the following example:
IP Address: 192.168.1.100 Subnet Mask: 255.255.255.0 2. Launch the web browser on your PC by entering the IP address of ECW5210-L (http://192.168.1.10) in the address field, and then press Enter. Example of entering ECW5210-L's default IP Address via a web browser 3. The following Admin Login Page will appear. Enter admin for both the Username and Password fields, and then click Login. Administrator Login Page 5 ECW-5210-L Enterprise Access Point ENGLISH Handbook 4. After a successful login to ECW5210-L, a System Overview page of the Web Management Interface will appear, as depicted below. 5. To logout, simply click on the Logout button at the upper right hand corner of the interface to return to the The Web Management Interface - System Overview Page Administrator Login Page. Click OK to logout. 6 ECW-5210-L Enterprise Access Point ENGLISH Handbook Common Settings Step 1. Change Administrators Password Change Password Page Click on the Utilities icon on the main menu, and select the Change Password tab. Enter a new password with a length of up to 32 characters, and retype it in the Re-enter New Password field. Click SAVE to save the changes. 7 ECW-5210-L Enterprise Access Point ENGLISH Handbook Step 2. Configure General AP (Access Point) Settings Wireless General Settings Page Click on the Wireless icon on the main menu, and then select the General tab. Determine the Band, Protocol and Channel settings:
Select your preferred Band, Protocol and Channel for you wireless connection. For example, select 2.4GHz for the band, 802.11g+802.11n for the protocol and 6 for the channel. Note:
Admin should be aware of Dynamic Frequency Selection (DFS) mandated on some channels of the 5GHz band. When an ECW5210-L detects interference, this mechanism will limit the ability to broadcast the SSID on one of the channels listed below:
1) Country Code: 841 (US) DFS Channels: 52 56 60 64 100 104 108 112 116 132 136 140 149 153 157 161 165 2) Country Code: 250 (EU) DFS Channels: 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140 8 ECW-5210-L Enterprise Access Point ENGLISH Handbook Step 3. Configure VAP (Virtual Access Point) Profile Settings VAP Configuration Page (VAP-1 shown) ECW5210-L supports up to 16 virtual APs (VAPs) per RF Card. Configure VAP profile settings
(a) Select the VAP Configuration tab to configure the settings of the desired VAP.
(b) Enable a specific VAP from the drop-down menu of Profile Name and configure related settings below. Check VAP status After finishing VAP configuration, the status of enabled Virtual APs shall be reflected on the VAP Overview page. 9 ECW-5210-L Enterprise Access Point ENGLISH Handbook Virtual AP Overview Page 10 ECW-5210-L Enterprise Access Point ENGLISH Handbook Step 4. Configure WDS (Wireless Distribution System) Settings (Optional) To extend the wireless coverage, ECW5210-L supports up to 8 WDS links per RF card for connecting wirelessly to other WDS-capable APs (peer APs). By default, all WDS profiles are disabled. Click on the Wireless button on the main menu. Select the Repeater Settings tab. Choose WDS as the Repeater Type. Choose the desired WDS profile:
(a) Enable WDS.
(b) Enter the Remote AP MAC Address (peer AP) and then Click SAVE. If you are using another ECW5210-L as the peer AP, simply repeat the above-mentioned steps to configure another peer AP(s). Note:
On each and every configuration page, you may click SAVE to save the changes of your configured settings, but you must reboot the system for the changes to take effect. After clicking SAVE, the following message will appear: Some modifications have been saved and will take effect after APPLY. 11 Congratulations!
ECW-5210-L Enterprise Access Point ENGLISH Handbook Now, Edgecore ECW5210-L is installed and configured successfully. After ECW5210-L's network configuration is completed, please remember to change the IP Address of your PC Connection Properties back to its original settings in order to ensure that your PC functions properly in its real network environments. It is strongly recommended to make a backup copy of your configuration settings. P/N: V34220171018 12