FCC ID: NDD9572150901 150N Wireless LAN Access Point

150N Wireless LAN Access Point Users Manual Version 1.0

(February, 2009) COPYRIGHT Copyright 2009/2010 by this company. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, this company reserves the right to revise this publication and to make changes from time to time in the contents thereof without obligation to notify any person of such revision or changes. Federal Communication Commission Interference Statement FCC Part 15 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio technician for help. FCC Caution This equipment must be installed and operated in accordance with provided instructions and a minimum 20 cm spacing must be provided between computer mounted antenna and persons body (excluding extremities of hands, wrist and feet) during wireless modes of operation. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment. Federal Communication Commission (FCC) Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The equipment version marketed in US is restricted to usage of the channels 1-11 only. R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC

(Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000. Safety This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment. EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxembourg, the Netherlands, Portugal, Spain, Sweden, and the United Kingdom. The ETSI version of this device is also authorized for use in EFTA member states:

Iceland, Liechtenstein, Norway, and Switzerland. EU Countries Not intended for use None. C A T A L O G Chapter I: Product Information ................................................................ 1 1-1 Product Introduction ........................................................................................ 1 1-2 Safety Information ........................................................................................... 2 1-3 System Requirements ...................................................................................... 3 1-4 Package Contents ............................................................................................. 4 1-5 Familiar with your new wireless access point ................................................. 5 Chapter II: System and Network Setup .................................................... 7 2-1 Installing the access point to your Network .................................................... 7 2-2 Connecting to wireless access point by web browser...................................... 8 2-2-1 Windows 95/98/Me IP address setup ............................................................... 8 2-2-2 Windows 2000 IP address setup ..................................................................... 10 2-2-3 Windows XP IP address setup ........................................................................ 12 2-2-4 Windows Vista IP address setup ..................................................................... 14 2-2-5 Connecting to Web Management Interface .................................................... 17 2-3 View System Status and Information ............................................................ 19 2-4 Select an Operating Mode for Wireless Access Point ................................... 21 2-4-1 AP Mode......................................................................................................... 23 2-4-1-1 Multiple ESSID ................................................................................... 25 2-4-2 Station-Infrastructure ..................................................................................... 26 2-4-2-1 Wireless Site Survey ........................................................................... 28 2-4-3 AP Bridge-Point to Point Mode ..................................................................... 29 2-4-4 AP Bridge-Point to Multi-Point Mode ........................................................... 32 2-4-5 AP Bridge-WDS Mode .................................................................................. 34 2-4-6 Universal Repeater ......................................................................................... 36 2-5 WPS Setting ................................................................................................... 39 2-6 Advanced Wireless Settings........................................................................... 42 2-7 Wireless Security ........................................................................................... 45 2-7-1 Disable Security ............................................................................................. 47 2-7-2 WEP ............................................................................................................... 48 2-7-3 WPA Pre-shared Key ...................................................................................... 50 2-7-4 WPA RADIUS................................................................................................ 52 2-7-5 802.1x Authentication .................................................................................... 54 2-8 Radius Server ................................................................................................. 56 2-9 MAC Filtering ............................................................................................... 59 2-10 System Utilities............................................................................................ 61 2-10-1 Change Password ......................................................................................... 61 2-10-2 IP Address of the Wireless Access Point ...................................................... 62 2-10-3 DHCP Server ................................................................................................ 64 Chapter III: Advanced Configuration .................................................... 66 3-1 Configuration Backup and Restore................................................................ 66 3-2 Firmware Upgrade ......................................................................................... 67 3-3 System Reset.................................................................................................. 68 Chapter IV: Appendix .............................................................................. 69 4-1 Hardware Specification ................................................................................. 69 4-2 Troubleshooting ............................................................................................. 70 4-3 Glossary ......................................................................................................... 72 Chapter I: Product Information 1-1 Product Introduction Thank you for purchasing this wireless access point! With this high cost-efficiency wireless access point, computers and wireless devices which are compatible with 802.11 Draft-N can connect to existing wired Ethernet network via this wireless access point, at the speed of 150Mbps. Easy install procedures allows any computer users to setup a network environment in very short time - within minutes, even inexperienced users. Just follow the instructions given in this user manual, you can complete the setup procedure and release the power of this access point all by yourself!

Other features of this access point including:

Compatible with IEEE 802.11b/g wireless network standard - works with other 802.11b/g/Draft-N wireless devices. High speed wireless network, six times faster than conventional 802.11g wireless network (up to 150Mbps). Allow wireless devices to connect to existing wired network and share network resources. Supports DHCP server function. Supports 64/128-bit WEP, WPA, and WPA2 wireless data encryption. Supports MAC address filtering (Only allow specific wireless device of your choice to connect to this access point). Supports RADIUS server, only allow users listed in your authorization server to use wireless network. Supports WPS (Wi-Fi Protected Setup), simplifies wireless client setup procedures. Even inexperienced user can setup wireless network without network technicians help!

Easy to use web-based GUI (Graphical User Interface) for network configuration and management purposes. 1 1-2 Safety Information In order to keep the safety of users and your properties, please follow the following safety instructions:

1. This access point is designed for indoor use only; DO NOT place this access point outdoor. 2. DO NOT put this access point at or near hot or humid places, like kitchen or bathroom. Also, do not left this access point in the car in summer. 3. DO NOT pull any connected cable with force; disconnect it from the access point first. 4. If you want to place this access point at high places or hang on the wall, please make sure the access point is firmly secured. Falling from high places would damage the access point and its accessories, and warranty will be void. 5. Accessories of this access point, like antenna and power supply, are danger to small children under 3 years old. They may put the small parts in their nose or month and it could cause serious damage to them. KEEP THIS ACCESS POINT OUT THE REACH OF CHILDREN!

6. The access point will become hot when being used for long time (This is normal and is not a malfunction). DO NOT put this access point on paper, cloth, or other flammable materials. 7. Theres no user-serviceable part inside the access point. If you found that the access point is not working properly, please contact your dealer of purchase and ask for help. DO NOT disassemble the access point, warranty will be void. 8. If the access point falls into water when its powered, DO NOT use your hand to pick it up. Switch the electrical power off before you do anything, or contact an experienced electrical technician for help. 9. If you smell something strange or even see some smoke coming out from the access point or power supply, remove the power supply or switch the electrical power off immediately, and call dealer of purchase for help. 2 1-3 System Requirements Computer or network devices with wired or wireless network interface card. Web browser (Microsoft Internet Explorer 4.0 or above, Netscape Navigator 4.7 or above, Opera web browser, or Safari web browser). An available AC power socket (100 240 V, 50/60Hz) 3 1-4 Package Contents Before you starting to use this access point, please check if theres anything missing in the package, and contact your dealer of purchase to claim for missing items:

Wireless Access Point (main body, 1 pcs) 3dBi Dipole Antenna (1 pcs) User Manual (1 pcs) A/C Power Adapter (1 pcs) 4 1-5 Familiar with your new wireless access point Front Panel LED Name Light Status Description PWR WLAN On On Off The access point is switched on and correctly powered. Wireless WPS mode is enabled. Wireless network is switched off. Flashing Wireless LAN activity (transferring or receiving data). LAN On Off LAN port is connected LAN port is not connected Flashing LAN activity (transferring or receiving data) 5 Back Panel Item Name Description Antennas Two reserve SMA antenna connectors for screwing 3dBi Power LAN detachable antennas enclosed with the product. Power connector, connects to A/C power adapter. Local Area Network (LAN) port. Reset / WPS Reset the router to factory default settings (clear all settings) or start WPS function. Press this button and hold for 10 seconds to restore all settings to factory defaults, and press this button for less than 5 seconds to start WPS function. 6 Chapter II: System and Network Setup 2-1 Installing the access point to your Network Please follow the following instruction to build the network connection between your new wireless access point and your computers, network devices:

1. Connect the access point to ADSL modem, router, or switch/hub in your network through the LAN port of the access point by Ethernet cable. 2. Connect the A/C power adapter to the wall socket, and then connect it to the Power socket of the access point. 3. Please check all LEDs on the front panel. PWR LED should be steadily on, LAN LEDs should be on if the access point is correctly connected to the ADSL modem, router or switch/hub. If PWR LED is not on, or any LED you expected is not on, please recheck the cabling, or jump to 4-2 Troubleshooting for possible reasons and solution. 7 2-2 Connecting to wireless access point by web browser Before you can connect to the access point and start configuration After the network connection is built, the next step you should do is setup the access point with proper network parameters, so it can work properly in your network environment. procedures, your computer must be able to get an IP address automatically (use dynamic IP address). If its set to use static IP address, or youre unsure, please follow the following instructions to configure your computer to use dynamic IP address:

If the operating system of your computer is. 2-2-1 Windows 95/98/Me IP address setup 1. Click Start button (it should be located at lower-left corner of your computer), then click control panel. Double-click Network icon, and Network window will appear. Select TCP/IP, then click Properties.

- please go to section 2-2-1

- please go to section 2-2-2

- please go to section 2-2-3 please go to section 2-2-4 Windows 95/98/Me Windows 2000 Windows XP Windows Vista 8 2. Select Specify an IP address, then input the following settings in respective field:

IP address: 192.168.2.2 Subnet Mask: 255.255.255.0 click OK when finish. 9 2-2-2 Windows 2000 IP address setup 1. Click Start button (it should be located at lower-left corner of your computer), then click control panel. Double-click Network and Dial-up Connections icon, double click Local Area Connection, and Local Area Connection Properties window will appear. Select Internet Protocol

(TCP/IP), then click Properties 10 2. Select Use the following IP address, then input the following settings in respective field:

IP address: 192.168.2.2 Subnet Mask: 255.255.255.0 click OK when finish. 11 2-2-3 Windows XP IP address setup 1. Click Start button (it should be located at lower-left corner of your computer), then click control panel. Double-click Network and Internet Connections icon, click Network Connections, and then double-click Local Area Connection, Local Area Connection Status window will appear, and then click Properties 12 2. Select Use the following IP address, then input the following settings in respective field:

IP address: 192.168.2.2 Subnet Mask: 255.255.255.0 click OK when finish. 13 2-2-4 Windows Vista IP address setup 1. Click Start button (it should be located at lower-left corner of your computer), then click control panel. Click View Network Status and Tasks, then click Manage Network Connections..Right-click Local Area Netwrok, then select Properties. Local Area Connection Properties window will appear, select Internet Protocol Version 4 (TCP / IPv4), and then click Properties 14 2. Select Use the following IP address, then input the following settings in respective field:

IP address: 192.168.2.2 Subnet Mask: 255.255.255.0 click OK when finish. 15 16 2-2-5 Connecting to Web Management Interface All functions and settings of this access point must be configured via web management interface. Please start your web browser, and input 192.168.2.1 in address bar, then press Enter key. The following message should be shown:

Please input user name and password in the field respectively, default user name is admin, and default password is 1234, then press OK button, and you can see the web management interface of this access point:

17 NOTE: If you cant see the web management interface, and youre being prompted to input user name and password again, it means you didnt input username and password correctly. Please retype user name and password again. If youre certain about the user name and password you type are correct, please go to 4-2 Troubleshooting to perform a factory reset, to set the password back to default value. 18 2-3 View System Status and Information After you connected to the access point by web browser, the first thing you see is Status and Information page. All system and network related information of this access point will be displayed here. The information is very helpful when you want to know the detailed information of your access point, and when you try to fix the communication problem between this access point and other wired / wireless computer / devices. You can click Home on the left, and the system status and information will be displayed, as shown below:

Here are descriptions of every item:

Up time Displays the total passed time since the wireless access point is powered. Hardware Version Displays hardware version. This information is helpful when you need online help from the dealer of purchase. 19 Runtime Code Version Mode ESSID Displays current firmware version. If you want to perform firmware upgrade, this number will help you to determine if you need such upgrade. Displays current wireless operating mode (see next Section) Displays current ESSID (the name used to identify this wireless access point) Channel Number Displays current wireless channel number Security Displays current wireless security setting Displays current BSSID (a set of unique BSSID identification name of this access point, it can not be modified by user) Associated Clients Displays the number of connected wireless client IP Address Displays the IP address of this wireless access point Displays the net mask of IP address Subnet Mask Default Gateway Displays the IP address of default gateway MAC address Displays the MAC address of LAN interface 20 2-4 Select an Operating Mode for Wireless Access Point This access point can be operated in different modes; you can click Basic Setting on the left of web management interface to select an operating mode you want to meet for different needs:

You can click Mode dropdown menu to select operating mode, and there are 6 operating modes available:

AP Access point mode, allows wireless clients to connect to access point and exchange data with the devices connected to the wired network. Station-Infrastructure Enable the Ethernet device such us TV and Game player connected to the access point to a wireless client. Establish wireless connection with another wireless access point using the same mode, and link the wired network which these two wireless access points connected to together. Only one AP Bridge-Point to Point 21 AP Bridge-Point to Multi-Point AP Bridge-WDS Universal Repeater access point can be connected in this mode. Establish wireless connection with other wireless access points using the same mode, and link the wired network which these wireless access points connected to together. Up to 4 access points can be connected in this mode. This mode is similar to AP Bridge to Multi-Point, but access point is not work in bridge-dedicated mode, and will be able to accept wireless clients while the access point is working as a wireless bridge. This product can act as a wireless range extender that will help you to extend the networking wirelessly. The access point can act as Station and AP at the same time. It can use Station function to connect to a Root AP and use AP function to service all wireless clients within its coverage. Please select one wireless operating mode, for detailed descriptions of every operating mode; please refer to Section 2-4-1 to 2-4-6 listed below. 22 2-4-1 AP Mode This is the most common mode. When in AP mode, this access point acts as a bridge between 802.11b/g/Draft-N wireless devices and wired Ethernet network, and exchange data between them. When you select AP, the following options will be displayed:

Here are descriptions of every setup item:

Band Please select the wireless band you wish to use. By selecting different band setting, youll be able to allow or deny the wireless client of a certain band. If you select 2.4GHz (B), 2.4GHz (N), or 2.4GHz

(G), only wireless clients using the wireless band you select (802.11b, 802.11 Draft-N, or 802.11g) will be able to connect to this access point. If you select 2.4GHz (B+G), then only wireless clients using 802.11b and 802.11g band will be able to connect to this access point. If you want to allow 802.11b, 802.11g, and 802.11 Draft-N clients to connect to this access point, select 2.4GHz (B+G+N). Please input the ESSID (the name used to identify this wireless access point) here. You can input up to 32 alphanumerical characters. PLEASE NOTE 23 Main ESSID Multiple ESSID THAT ESSID IS CASE SENSITIVE. The access point supports multiple SSID function;

up to four SSIDs can be set. If you want to configure additional SSIDs, please click this button. For detailed descriptions of the function, please refer to Section 2-4-1-1. Channel Number Please select a channel number you wish to use. If you know a certain channel number is being used by other wireless access points nearby, please refrain from using the same channel number Associated Clients Click Show Active Clients button and a new popup window will appear which contains the information about all wireless clients connected to this access point. You can click Refresh button in popup window to keep information up-to-date. After you finish with setting, please click Apply, and the following message will be displayed:

When you see this message, the settings you made is successfully save. You can click Continue button to back to previous page and continue on other setting items, or click Apply button to restart the wireless access point and the changes will take effect after about 30 seconds. 24 2-4-1-1 Multiple ESSID This access point supports four SSIDs. Except the main SSID (It can be configure in Basic Setting page), you can configure another three of SSIDs here. With different SSIDs, you can separate the wireless networks with different SSID name, wireless security, WMM, and VLAN settings. NOTE: If you want to configure the wireless security for different SSID, please go to 2-7 Wireless Security for more information. Here are descriptions of every setup item:

No. Enable SSID Except Main SSID, you can configure additional three ESSID here. Select the box to enable the different additional ESSID. Please input the SSID name (the name used to identify this wireless access point) here. You can input up to 32 alphanumerical characters. PLEASE NOTE THAT ESSID IS CASE SENSITIVE. 25 Broadcast SSID WMM VLAN ID

(0:Untagged) Decide if the wireless access point will broadcast its own ESSID or not. You can hide the ESSID of your wireless access point (set the option to Disable), so only people those who know the ESSID of your wireless access point can get connected. WMM (Wi-Fi Multimedia) technology, which can improve the performance of certain network applications, like audio/video streaming, network telephony (VoIP), and others. When you enable WMM function, the access point will define the priority of different kinds of data, to give higher priority to applications which require instant responding. Therefore you can improve the performance of such network applications. If your network uses VLANs, you can assign the SSID to a VLAN on your network. Client devices that associate using the SSID are grouped into this VLAN. The VLAN ID range is from 1 to 4094. The VLAN ID is 0 by default, it means that disable the VLAN function for the ESSID. 2-4-2 Station-Infrastructure In this mode, you can connect the access point to Ethernet device such us TV and Game player to enable the Ethernet device be a wireless station and join to a wireless network through an access point or AP router. 26 Here are descriptions of every setup item:

Band Please select the wireless band you wish to use. By selecting different band setting, youll be able to allow or deny the wireless client of a certain band. If you select 2.4GHz (B), 2.4GHz (N), or 2.4GHz

(G), only wireless clients using the wireless band you select (802.11b, 802.11 Draft-N, or 802.11g) will be able to connect to this access point. If you select 2.4GHz (B+G), then only wireless clients using 802.11b and 802.11g band will be able to connect to this access point. If you want to allow 802.11b, 802.11g, and 802.11 Draft-N clients to connect to this access point, select 2.4GHz (B+G+N). Please input the ESSID (the name used to identify this wireless access point) here. You can input up to 32 alphanumerical characters. PLEASE NOTE THAT ESSID IS CASE SENSITIVE. When you use this access point as a wireless station for Ethernet network device to have wireless capability, you have to associate it with a working access point. Click Select Site Survey button, then a Wireless Site Survey Table will pop up. It will list all available access points near by. You can select one access point in the table and it will join wireless LAN through this access point. Please go to Section 2-4-2-1 for more information about the Wireless Site Survey Table. Main ESSID Site Survey After you finish with setting, please click Apply, and the following message will be displayed:

27 When you see this message, the settings you made is successfully save. You can click Continue button to back to previous page and continue on other setting items, or click Apply button to restart the wireless access point and the changes will take effect after about 30 seconds. 2-4-2-1 Wireless Site Survey The table will list the access points nearby as the access point is set to Station mode; you can select one of the access points to associate. Here are descriptions of every setup item:

28 Select Channel SSID BSSID Encryption Authentication Signal Mode Refresh Connection Click the radio button to select the access point. Display to channel number of the access point. Display the SSID name of the access point. Display the BSSID (MAC Address) of the access point. Display the encryption setting of the access points. If you have selected the access point with security setting, you have to go to 2-7 Wireless Security to set the same security with the access point you want to associate. Display the authentication type of the access point. The signal strength of each access point will be displayed here. The signal strength is stronger, the connection quality is better. Display the wireless modes include 11b, 11b/g or 11b/g/n or 11n only of the access points. Click this button to refresh the table. Select an access point and click this button to choose the network. The SSID name of the access point you have selected will be displayed in the Main SSID in the Basic Setting page. 2-4-3 AP Bridge-Point to Point Mode In this mode, this wireless access point will connect to another wireless access point which uses the same mode, and all wired Ethernet clients of both wireless access points will be connected together. You can use this mode to connect a network to another network which is physically isolated. Please note that when you set your access point to this mode, it will not accept regular wireless clients anymore. When you select AP Bridge-Point to Point, the following options will be displayed:

29 Here are descriptions of every setup item:

Band Please select the wireless band you wish to use. By selecting different band setting, youll be able to allow or deny the wireless client of a certain band. If you select 2.4GHz (B), 2.4GHz (N), or 2.4GHz

(G), only wireless clients using the wireless band you select (802.11b, 802.11 Draft-N, or 802.11g) will be able to connect to this access point. If you select 2.4GHz (B+G), then only wireless clients using 802.11b and 802.11g band will be able to connect to this access point. If you want to allow 802.11b, 802.11g, and 802.11 Draft-N clients to connect to this access point, select 2.4GHz (B+G+N). MAC address 1 Channel Number Please select a channel number you wish to use. The channel number must be same with another wireless access point you wish to connect Please input the MAC address of the wireless access point you wish to connect Click this button to select an encryption mode for this wireless link, a new popup window will appear. Please refer to Section 2-7 for detailed descriptions. Set Security After you finish with setting, please click Apply, and the following 30 message will be displayed:

When you see this message, the settings you made is successfully saved, you can click Continue button to back to previous page and continue on other setting items, or click Apply button to restart the wireless access point and the changes will take effect after about 30 seconds. 31 2-4-4 AP Bridge-Point to Multi-Point Mode In this mode, this wireless access point will connect to up to four wireless access points which uses the same mode, and all wired Ethernet clients of every wireless access points will be connected together. You can use this mode to connect a network to other networks which is physically isolated. Please note that when you set your access point to this mode, it will not accept regular wireless clients anymore. When you select AP Bridge-Point to Multi-Point, the following options will be displayed:

Here are descriptions of every setup item:

Band Please select the wireless band you wish to use. By selecting different band setting, youll be able to allow or deny the wireless client of a certain band. If you select 2.4GHz (B), 2.4GHz (N), or 2.4GHz

(G), only wireless clients using the wireless band you select (802.11b, 802.11 Draft-N, or 802.11g) will be able to connect to this access point. If you select 2.4GHz (B+G), then only wireless clients using 802.11b and 802.11g band will be 32 able to connect to this access point. If you want to allow 802.11b, 802.11g, and 802.11 Draft-N clients to connect to this access point, select 2.4GHz (B+G+N). MAC address 1-4 Channel Number Please select a channel number you wish to use. The channel number must be same with another wireless access point you wish to connect Please input the MAC address of the wireless access point you wish to connect Click this button to select an encryption mode for this wireless link, a new popup window will appear. Please refer to Section 2-7 for detailed descriptions. Set Security After you finish with setting, please click Apply, and the following message will be displayed:

When you see this message, the settings you made is successfully save. You can click Continue button to back to previous page and continue on other setting items, or click Apply button to restart the wireless access point and the changes will take effect after about 30 seconds. 33 2-4-5 AP Bridge-WDS Mode In this mode, this wireless access point will connect to up to four wireless access points which uses the same mode, and all wired Ethernet clients of every wireless access points will be connected together. You can use this mode to connect a network to other networks which is physically isolated. When you use this mode, this access point is still able to accept wireless clients. When you select AP Bridge-WDS, the following options will be displayed:

Here are descriptions of every setup item:

Band Please select the wireless band you wish to use. By selecting different band setting, youll be able to allow or deny the wireless client of a certain band. If you select 2.4GHz (B), 2.4GHz (N), or 2.4GHz

(G), only wireless clients using the wireless band you select (802.11b, 802.11 Draft-N, or 802.11g) will be able to connect to this access point. 34 If you select 2.4GHz (B+G), then only wireless clients using 802.11b and 802.11g band will be able to connect to this access point. If you want to allow 802.11b, 802.11g, and 802.11 Draft-N clients to connect to this access point, select 2.4GHz (B+G+N). Please input the ESSID (the name used to identify this wireless access point) here. You can input up to 32 alphanumerical characters. PLEASE NOTE THAT ESSID IS CASE SENSITIVE. The access point supports multiple SSID function;

up to four SSIDs can be set. If you want to configure additional SSIDs, please click this button. For detailed descriptions of the function, please refer to Section 2-4-1-1. MAIN ESSID Multiple ESSID Channel Number Please select a channel number you wish to use. The channel number must be same with another wireless access point you wish to connect MAC address 1-4 Associated Clients Click Show Active Clients button and a new popup window will appear which contains the information about all wireless clients connected to this access point. You can click Refresh button in popup window to keep information up-to-date. Please input the MAC address of the wireless access point you wish to connect Click this button to select an encryption mode for this wireless link, a new popup window will appear. Please refer to Section 2-7 for detailed descriptions. Set Security After you finish with setting, please click Apply, and the following message will be displayed:

35 When you see this message, the settings you made is successfully save. You can click Continue button to back to previous page and continue on other setting items, or click Apply button to restart the wireless access point and the changes will take effect after about 30 seconds. 2-4-6 Universal Repeater In this mode, the access point can act as a wireless repeater; it can be Station and AP at the same time. It can use Station function to connect to a Root AP and use AP function to service all wireless stations within its coverage. NOTE: For Repeater Mode, this access point will demodulate the received signal, checking if this signal is noise for the operating network then have the signal modulated and amplified again. The output power of this mode is the same as that of WDS and normal AP mode. 36 Here are descriptions of every setup item:

Band Please select the wireless band you wish to use. By selecting different band setting, youll be able to allow or deny the wireless client of a certain band. If you select 2.4GHz (B), 2.4GHz (N), or 2.4GHz

(G), only wireless clients using the wireless band you select (802.11b, 802.11 Draft-N, or 802.11g) will be able to connect to this access point. If you select 2.4GHz (B+G), then only wireless clients using 802.11b and 802.11g band will be able to connect to this access point. If you want to allow 802.11b, 802.11g, and 802.11 Draft-N clients to connect to this access point, select 2.4GHz (B+G+N). Please input the ESSID (the name used to identify this wireless access point) here. You can input up to 32 alphanumerical characters. PLEASE NOTE THAT ESSID IS CASE SENSITIVE. The access point supports multiple SSID function;

up to four SSIDs can be set. If you want to configure additional SSIDs, please click this button. For detailed descriptions of the function, please refer to Section 2-4-1-1. MAIN SSID Multiple ESSID Channel Number Please select a channel number you wish to use. The channel number must be same with another wireless access point you wish to connect Associated Clients Click Show Active Clients button and a new popup window will appear which contains the information about all wireless clients connected to this access point. You can click Refresh button in popup window to keep information up-to-date In Universal Repeater mode, this device can act as a station to connect to a Root AP. You should assign the SSID of the Root AP here or click Root AP SSID 37 Select Site Survey Click Select Site Survey button, then a Wireless Select Site Survey button to choose a Root AP. Site Survey Table will pop up. It will list all available access points near by. You can select one access point in the table and the access point will join wireless LAN through this access point. Please go to Section 2-4-2-1 for more information about the Wireless Site Survey Table. After you finish with setting, please click Apply, and the following message will be displayed:

When you see this message, the settings you made is successfully save. You can click Continue button to back to previous page and continue on other setting items, or click Apply button to restart the wireless access point and the changes will take effect after about 30 seconds. 38 2-5 WPS Setting Wi-Fi Protected Setup (WPS) is the simplest way to build connection between wireless network clients and this access point. You dont have to select encryption mode and input a long encryption passphrase every time when you need to setup a wireless client, you only have to press a button on wireless client and this access point, and the WPS will do the setup for you. This access point supports two types of WPS: Push-Button Configuration

(PBC), and PIN code. If you want to use PBC, you have to switch this access point to WPS mode and push a specific button on the wireless client to start WPS mode. You can push Reset/WPS button of this access point, or click Start PBC button in the web configuration interface to do this; if you want to use PIN code, you have to provide the PIN code of the wireless client you wish to connect to this access point and then switch the wireless client to WPS mode. The detailed instructions are listed follow:

To use WPS function to set encrypted connection between this access point and WPS-enabled wireless client by WPS, click WPS Setting on the left of web management menu, and the following information will be displayed:

Note: WPS function of this access point will not work for those wireless clients do not support WPS. 39 Here are descriptions of every setup item:

Enable WPS Wi-Fi Protected Setup Information Check this box to enable or disable WPS function All information related to WPS will be displayed here, theyre helpful when youre setting up connections by WPS. WPS Status: Displays WPS status. If data encryption settings of this access point has never been set, unConfigured message will be displayed her. (see Section 2-7 for detailed information); if data encryption settings has been set before, Configured message will be displayed here. Self PinCode: This is the WPS PIN code of this access point. This code is useful when you need to build wireless connection by WPS with other WPS-enabled wireless devices. SSID: Displays the SSID (ESSID) of this access point. 40 Authentication Mode: The wireless security authentication mode of this access point will be displayed here. If you dont enable security function of the access point before WPS is activated, the access point will auto set the security to WPA (AES) and generate a set of passphrase key for WPS connection. Passphrase Key: Displays the WPA passphrase here, all characters will be replaced by asterisk for security reason. If encryption is not set on this access point, nothing will be displayed here. There are Registrar and Enrollee modes for the WPS connection. When Registrar is enabled, the wireless clients will follow the access points wireless settings for WPS connection. When Enrolle mode is enabled, the access point will follow the wireless settings of wireless client for WPS connection. Click Start PBC to start Push-Button style WPS setup procedure. This access point will wait for WPS requests from wireless clients for 2 minutes. The WLAN LED on the access point will be steady on for 2 minutes when this access point is waiting for incoming WPS request. Please input the PIN code of the wireless client you via client wish to connect, and click Start PIN button. The WLAN LED on the access point will be steady on when this access point is waiting for incoming WPS request. Config Mode Start PBC Start PIN NOTE: When youre using PBC type WPS setup, you must press PBC button (hardware or software) of wireless client within 120 seconds; if you didnt press PBC button of wireless client within this time period, please press PBC button (hardware or software) of this access point again. 41 2-6 Advanced Wireless Settings This wireless access point has many advanced wireless features. Please note that all settings listed here are for experienced users only, if youre not sure about the meaning and function of these settings, please dont modify them, or the wireless performance will be reduced. You can click Advanced Setting on the left to enter advanced settings menu, and the following message will be displayed:

Here are descriptions of every setup item:

Fragment Threshold RTS Threshold Beacon Interval Set the Fragment threshold of wireless radio. Do not modify default value if you dont know what it is, default value is 2346 Set the RTS threshold of wireless radio. Do not modify default value if you dont know what it is, default value is 2347 Set the beacon interval of wireless radio. Do not modify default value if you dont know what it is, 42 DTIM Period Data Rate N Data Rate Channel Width Preamble Type default value is 100 Set the DTIM period of wireless radio. Do not modify default value if you dont know what it is, default value is 3 Set the wireless data transfer rate to a certain value. Since most of wireless devices will negotiate with each other and pick a proper data transfer rate automatically, its not necessary to change this value unless you know what will happen after modification. Set the data rate of 802.11 Draft-N clients, available options are MCS 0 to MCS 15, its safe to set this option to Auto and its not necessary to change this value unless you know what will happen after modification. Select wireless channel width (bandwidth taken by wireless signals of this access point). Its suggested to select Auto 20/40MHz. Do not change to 20 MHz unless you know what it is. Set the type of preamble of wireless radio, Do not modify default value if you dont know what it is, default setting is Short Preamble. WMM Broadcast ESSID Decide if the wireless access point will broadcast its own ESSID or not. You can hide the ESSID of your wireless access point (set the option to Disable), so only people those who know the ESSID of your wireless access point can get connected. WMM (Wi-Fi Multimedia) technology, which can improve the performance of certain network applications, like audio/video streaming, network telephony (VoIP), and others. When you enable WMM function, the access point will define the priority of different kinds of data, to give higher priority to applications which require instant responding. Therefore you can improve the performance of such network applications. Enabling this setting will reduce the chance of CTS Protect 43 TX Power radio signal collisions between 802.11b and 802.11g wireless access points. Its recommended to set this option to Auto. You can set the output power of wireless radio. Unless youre using this wireless access point in a really big space, you may not have to set output power to 100%. This will enhance security

(malicious / unknown users in distance will not be able to reach your wireless access point). After you finish with setting, please click Apply, and the following message will be displayed:

When you see this message, the settings you made is successfully save. You can click Continue button to back to previous page and continue on other setting items, or click Apply button to restart the wireless access point and the changes will take effect after about 30 seconds. 44 2-7 Wireless Security This wireless access point provides many types of wireless security

(wireless data encryption). When you use data encryption, data transferred by radio signals in the air will become unreadable for those people who dont know correct encryption key (encryption password). There are two ways to set wireless security:

1. Click Security on the left of web management interface. 2. Click Set Security button when the wireless operating mode you selected is AP Bridge-Point to Point, AP Bridge-Point to Multi-Point, or AP Bridge-WDS. 45 NOTE: If you have enabled Multiple SSID function, please select the SSID network you wish to configure in advance. There are four types of security level you can select: Disable (no security

- data encryption disabled), WEP, WPA Pre-shared Key, and WPA Radius. Please refer to the following sections for detailed instructions. Please remember its very important to set wireless security settings properly! Without a proper setting, hackers and intruders may gain access to your local network and do something bad to your computers and servers, which could cause serious problem. There are several things you can do to improve wireless security:

1. Always enable data encryption. Only disable it when you want to open your wireless access point to the public. 2. Never use simple words as encryption password. Use the random combination of symbols, numbers, and alphabets will greatly improve security. 3. Use WPA when possible - it's much safer than WEP. 4. Change encryption password when youve used it for too long time. 46 2-7-1 Disable Security Select the SSID you wish to configure. When you select Disable, wireless encryption for the network is disabled. After you finish with setting, please click Apply, and the following message will be displayed:

When you see this message, the settings you made is successfully save. You can click Continue button to back to previous page and continue on other setting items, or click Apply button to restart the wireless access point and the changes will take effect after about 30 seconds. 47 2-7-2 WEP WEP (Wired Equivalent Privacy) is a common encryption mode, its safe enough for home and personal use. But if you need higher level of security, please consider using WPA encryption (see next Section). However, some wireless clients dont support WPA, but only support WEP, so WEP is still a good choice for you if you have such kind of client in your network environment. When you select WEP as encryption type, the following messages will be displayed:

Here are descriptions of every setup item:

Key Length Key Format There are two types of WEP key length: 64-bit and 128-bit. Using 128-bit is safer than 64-bit, but will reduce some data transfer performance. There are two types of key format: ASCII and Hex. When you select a key format, the number of characters of key will be displayed. For example, if you select 64-bit as key length, and Hex as key format, youll see the message at the right of Key 48 Default Tx Key Encryption Key 1 to 4 Enable 802.1x Authentication Format is Hex (10 characters), which means the length of WEP key is 10 characters. You can set up to four sets of WEP key, and you can decide which key is being used by default here. If you dont know which one you should use, select Key 1. Input WEP key characters here, the number of characters must be the same as the number displayed at Key Format field. You can use any alphanumerical characters (0-9, a-z, and A-Z) if you select ASCII key format, and if you select Hex as key format, you can use characters 0-9, a-f, and A-F. You must enter at least one encryption key here, and if you entered multiple WEP keys, they should not be same with each other. Check this box to enable 802.1x user authentication. Please refer to Section 2-7-5 for detailed instructions. After you finish with setting, please click Apply, and the following message will be displayed:

When you see this message, the settings you made is successfully save. You can click Continue button to back to previous page and continue on other setting items, or click Apply button to restart the wireless access point and the changes will take effect after about 30 seconds. 49 2-7-3 WPA Pre-shared Key WPA Pre-shared key is the safest encryption method currently, and its recommended to use this encryption method to ensure the safety of your data. When you select WPA pre-shared key as encryption type, the following messages will be displayed:

Here are descriptions of every setup item:

WPA Unicast Cipher Suite Pre-shared Key Format Pre-shared Key Available options are: WPA (TKIP), WPA2 (AES), and WPA2 Mixed. You can select one of them, but you have to make sure your wireless client support the cipher you selected. Please select the format of pre-shared key here, available options are Passphrase (8 to 63 alphanumerical characters) and Hex (64 hexadecimal characters 0 to 9 and a to f). Please input pre-shared key according to the key format you selected here. For security reason, dont use simple words). After you finish with setting, please click Apply, and the following message will be displayed:

50 When you see this message, the settings you made is successfully save. You can click Continue button to back to previous page and continue on other setting items, or click Apply button to restart the wireless access point and the changes will take effect after about 30 seconds. 51 2-7-4 WPA RADIUS WPA Radius is the combination of WPA encryption method and RADIUS user authentication. If you have a RADIUS authentication server, you can check the identify of every wireless client by user database. When you select WPA RADIUS as encryption type, the following messages will be displayed:

Here are descriptions of every setup item:

WPA Unicast Cipher Suite Use internal MD5/PEAP RADIUS Server You can select WPA encryption type here. AES is safer than TKIP, but not every wireless client supports it. Please refer to the specification of your wireless client to decide which encryption type you should use. Uses built-in RADIUS Server (refer to Section 2-8) instead of external RADIUS server. If you check this box, the value in following three fields will be ignored. Please input the IP address of RADIUS authentication server here. Please input the port number of RADIUS authentication server here. Default value is 1812. Please input the password of RADIUS authentication server here. RADIUS Server IP address RADIUS Server Port RADIUS Server Password After you finish with setting, please click Apply, and the following 52 message will be displayed:

When you see this message, the settings you made is successfully save. You can click Continue button to back to previous page and continue on other setting items, or click Apply button to restart the wireless access point and the changes will take effect after about 30 seconds. 53 2-7-5 802.1x Authentication You can enable 802.1x user identification (based on RADIUS user authentication server) by checking Enable 802.1x Authentication box when you select Disable or WEP as encryption type, and the following message will be displayed:

Here are descriptions of every setup item:

Select SSID Use internal MD5/PEAP RADIUS Server Choose the SSID you wish to configure. Uses built-in RADIUS Server (refer to next Section) instead of external RADIUS server. If you check this box, the value of internal RADIUS server fields will be ignored. Enable or disable the use of 802.1x user authentication. Please input the IP address of RADIUS authentication server here. Please input the port number of RADIUS authentication server here. Default value is 1812. Please input the password of RADIUS authentication server here. Enable 802.1x Authentication RADIUS Server IP address RADIUS Server Port RADIUS Server Password After you finish with setting, please click Apply, and the following message will be displayed:

54 When you see this message, the settings you made is successfully save. You can click Continue button to back to previous page and continue on other setting items, or click Apply button to restart the wireless access point and the changes will take effect after about 30 seconds. 55 2-8 Radius Server Comparing to other wireless security measures, radius server provides user-based authentication. If your wireless client supports 802.1x user authentication, you can use the Radius Server function to use the internal mini radius server to improve security and wireless user control. The internal radius server only supports 96 users and 16 IP addresses. If the number of user and/or IP address you need is more than this, please use external radius server. To setup internal radius server, click Raidus Server on the left of web management interface, and the following information will be displayed:

56 Here are descriptions of every setup item:

Enable Radius Server User Profile Check this box to enable internal radius server function. You can add or delete radius user here. Please input username, password, re-type password in corresponding field, and click Add button to add the user to radius server database. You can click Reset to clear the text you typed in above three fields. All current radius users will be listed here. If you want to delete one or more users, check Select box of that user, and click Delete Selected button;

you can click Delete All button to delete all users in radius server database. You can also click Reset button to uncheck all Select boxes. You can add allowed radius client IP address here. Please input client IP, secret key, re-type secret key in corresponding field, and click Add button to add the IP address to radius server database. You can click Reset to clear the text you typed in above three fields. All current IP addresses will be listed here. If you want to delete one or more addresses, check Select box of that address, and click Delete Selected button; you can click Delete All button to delete all addresses in radius server database. You can also click Reset button to uncheck all Select boxes. Authentication Client After you finish with setting, please click Apply, and the following message will be displayed:

57 When you see this message, the settings you made is successfully save. You can click Continue button to back to previous page and continue on other setting items, or click Apply button to restart the wireless access point and the changes will take effect after about 30 seconds. 58 2-9 MAC Filtering Another security measure you can use to keep hackers and intruders away is MAC filtering. You can pre-define a so-called white-list, which contains MAC addresses of the wireless clients you trust. All other wireless client with the MAC address which is not in your list will be denied by this wireless access point. To setup MAC filtering, please click MAC Filtering on the left of web management interface and the following messages will be displayed:

Address filtering table (1) Add new entry here (2) This page contains two parts of MAC filtering information. All allowed MAC addresses will be listed in upper part (1), and you can add new MAC addresses by components in lower part (2). Here are descriptions of every setup item:

Select Delete Selected Delete All Reset Check this box to select one or more MAC address(es) to delete. Click this button to delete all selected MAC address(es). Delete all MAC address entries. Uncheck all selected MAC address entries. 59 Enable Wireless Access Control MAC address Comment Add Clear Check this box to enable MAC address restriction, if unchecked, no restriction will be enforced (any wireless client with proper encryption setting will be able to connect to this wireless access point). Input MAC address allowed using this wireless access point here. You dont have to add colon (:) or hyphen (-) by yourself, just input 0 to 9 and a to f here, like 112233445566 or aabbccddeeff. You can input any text here as the comment of this MAC address, like ROOM 2A Computer or anything. You can input up to 16 alphanumerical characters here. This is optional and you can leave it blank, however, its recommended to use this field to write a comment for every MAC addresses as a memory aid. This is optional. When you finish inputting MAC address and

(optional) Comment, click this button to add the MAC address to the list. Remove all characters in MAC address and Comments field. After you finish with setting, please click Apply, and the following message will be displayed:

When you see this message, the settings you made is successfully save. You can click Continue button to back to previous page and continue on other setting items, or click Apply button to restart the wireless access point and the changes will take effect after about 30 seconds. 60 2-10 System Utilities This access point provides some control functions include password, IP address management, and DHCP server function. Please click System Utility on the left of web management interface to access these functions. Below are detailed descriptions of every control function. 2-10-1 Change Password You can change the password used to enter the web configuration menu of this wireless access point. Please click System Utility on the left, and the following message will be displayed:

Please input current password in Current Password field, then input new password in both New Password and Re-Enter Password field. After you finish, please go to the bottom of this page and click Apply, and the following message will be displayed:

When you see this message, the settings you made is successfully save. You can click Continue button to back to previous page and continue on other setting items, or click Apply button to restart the wireless access point and the changes will take effect after about 30 seconds. 61 2-10-2 IP Address of the Wireless Access Point You can change the IP address of this wireless access point, so it can become a part of your local network. Please remember this address or you will not be able to connect the configuration menu of this wireless access point. Default IP address is: 192.168.2.1 / Subnet Mask 255.255.255.0, you can press and hold Reset/WPS button over 10 seconds to change the IP address back to default value if you forget the IP address you set. To change IP address, please click System Utility on the left, and the following message will be displayed:

Please input IP address and Subnet Mask in corresponding field, and you can input the IP address of gateway in Gateway Address field, if you need to manage this wireless access point from other network (like Internet). If you want to activate the DHCP server function of this wireless access point, please select Enabled in DHCP Server option, and see next Section for detailed instructions; if you dont want to use DHCP server function of this wireless access point, or theres another DHCP server on the network this access point connects to, please select Disable. 62 After you finish, please go to the bottom of this page and click Apply, and the following message will be displayed:

When you see this message, the settings you made is successfully save. You can click Continue button to back to previous page and continue on other setting items, or click Apply button to restart the wireless access point and the changes will take effect after about 30 seconds. 63 2-10-3 DHCP Server This wireless access point is capable to act as a DHCP server for your network, and its disabled by default. If you want to activate this function, please click System Utility on the left, and the following message will be displayed:

NOTE: Please remember to select Enable in DHCP Server option as described in last Section or all DHCP-related fields will be grayed out, and you will not be able to input any DHCP parameter. Here are descriptions of every setup item:

Default Gateway IP Domain Name Server IP Start IP End IP Domain Name Please input the IP address of default gateway of your network here. Please input the IP address of domain name server

(DNS) here. Please input the start IP address of the IP range. Please input the end IP address of the IP range. If you wish, you can also optionally input the domain name for your network. This is optional. Please choose a lease time (the duration that every computer can keep a specific IP address) of every IP address assigned by this access point from dropdown menu. Lease Time 64 After you finish, please click Apply, and the following message will be displayed:

When you see this message, the settings you made is successfully save. You can click Continue button to back to previous page and continue on other setting items, or click Apply button to restart the wireless access point and the changes will take effect after about 30 seconds. 65 Chapter III: Advanced Configuration 3-1 Configuration Backup and Restore You can backup all configurations of this access point to a file, so you can make several copied of access point configuration for security reason. To backup or restore access point configuration, please follow the following instructions:

Please click Configuration Tool on the left of web management interface, and the following message will be displayed on your web browser:

Here are descriptions of every buttons:

Backup Settings Press Save... button, and youll be prompted to download the configuration as a file, default filename is config.bin, you can save it as another filename for different versions, and keep it in a safe place. Press Browse to pick a previously-saved configuration file from your computer, and then click Upload to transfer the configuration file to access point. After the configuration is uploaded, the access points configuration will be replaced by the file you just uploaded. Click this button to remove all settings you made, and restore the configuration of this access point back to factory default settings. 66 Restore Settings Restore to Factory Default 3-2 Firmware Upgrade If there are new firmware of this wireless access point available, you can upload the firmware to the access point to change the firmware with new one, to get extra functions or problem fix. To perform firmware upgrade, please click Upgrade on the left of web management interface, and the following message will be displayed:

Click Browse button first, youll be prompted to provide the filename of firmware upgrade file. Please download the latest firmware file from our website, and use it to upgrade your access point. After a firmware upgrade file is selected, click Apply button, and the access point will start firmware upgrade procedure automatically. The procedure may take several minutes, please be patient. NOTE: Never interrupt the upgrade procedure by closing the web browser or physically disconnect your computer from access point. If the firmware you uploaded is corrupt, the firmware upgrade will fail, and you may have to return this access point to the dealer of purchase to ask for help. (Warranty voids if you interrupted the upgrade procedure). 67 3-3 System Reset When you think the access point is not working properly, you can use this function to restart the access point; this may help and solve the problem. This function is useful when the access point is far from you or unreachable. However, if the access point is not responding, you may have to switch it off by unplug the power plug and plug it back again after 10 seconds. To reset your access point, please click Reset on the left, and the following message will be displayed:

Please click Apply, and a popup message will ask you again, to make sure you really want to reset the access point:

Click OK to reset the access point, or click Cancel to abort. Please remember all connections between wireless client and this access point will be disconnected. 68 Chapter IV: Appendix 4-1 Hardware Specification SoC: Ralink RT3050 Flash: 4MB SDRAM: 16MB LAN Port: 10/100M UTP Port x 1 Antenna: 3dBi Detachable Dipole Antenna x 1 Power: 12VDC, 1A Switching Power Adapter Dimension: 30(H) x 127(W) x 96(D) mm Transmit Power: 11n:14dBm 1.5dBm, 11g:15dBm 1.5dBm, 11b:17 1.5dBm Temperature: 32~104F (0 ~ 40C) Humidity: 10-90% (NonCondensing) Certification: FCC, CE 69 4-2 Troubleshooting If you found the access point is working improperly or stop responding to you, dont panic! Before you contact your dealer of purchase for help, please read this troubleshooting first. Some problems can be solved by yourself within very short time!

Scenario Access point is not responding to me when I want to access it by web browser Solution a. Please check the connection of power cord and network cable of this access point. All cords and cables should be correctly and firmly inserted to the access point. b. If all LEDs on this access point are out, please check the status of A/C power adapter, and make sure its correctly powered. c. You must use the same IP address section which access point uses. d. Are you using MAC or IP address filter?

Try to connect the access point by another computer and see if it works; if not, please perform a hard reset (pressing reset button). e. Set your computer to obtain an IP address automatically (DHCP), and see if your computer can get an IP address. f. If you did a firmware upgrade and this happens, contact your dealer of purchase for help. g. If all above solutions dont work, contact the dealer of purchase for help. a. If encryption is enabled, please re-check WEP or WPA passphrase settings on your wireless client. b. Try to move closer to wireless access point. c. Unplug the power plug of access point, and plug it back again after 10 seconds. d. If all LEDs on this access point are out, 70 Cant get connected to wireless access point please check the status of A/C power adapter, and make sure its correctly powered. a. Broadcast ESSID set to off?

b. Is Antenna properly installed and secured?

c. Are you too far from your access point? Try to get closer. d. Please remember that you have to input ESSID on your wireless client manually, if ESSID broadcast is disabled. a. Try to reset the access point and see if its better after that. b. Try to know what computers do on your local network. If someones transferring big files, other people will think Internet is really slow. c. Change channel number and see if this works. a. Make sure youre connecting to the correct IP address of the access point!

b. Password is case-sensitive. Make sure the Caps Lock light is not illuminated. c. If you really forget the password, do a hard reset. a. This is not a malfunction, if you can keep your hand on the access points case. b. If you smell something wrong or see the smoke coming out from access point or A/C power adapter, please disconnect the access point and A/C power adapter from utility power (make sure its safe before youre doing this!), and call your dealer of purchase for help. I cant locate my access point by my wireless client File download is very slow or breaks frequently I cant log onto web management interface:

password is wrong Access point become hot 71 4-3 Glossary Default Gateway (Access point): Every non-access point IP device needs to configure a default gateways IP address. When the device sends out an IP packet, if the destination is not on the same network, the device has to send the packet to its default gateway, which will then send it out towards the destination. DHCP: Dynamic Host Configuration Protocol. This protocol automatically gives every computer on your home network an IP address. DNS Server IP Address: DNS stands for Domain Name System, which allows Internet servers to have a domain name (such as www.Broadbandaccess point.com) and one or more IP addresses (such as 192.34.45.8). A DNS server keeps a database of Internet servers and their respective domain names and IP addresses, so that when a domain name is requested (as in typing "Broadbandaccess point.com" into your Internet browser), the user is sent to the proper IP address. The DNS server IP address used by the computers on your home network is the location of the DNS server your ISP has assigned to you. DSL Modem: DSL stands for Digital Subscriber Line. A DSL modem uses your existing phone lines to transmit data at high speeds. Ethernet: A standard for computer networks. Ethernet networks are connected by special cables and hubs, and move data around at up to 10/100 million bits per second

(Mbps). Idle Timeout: Idle Timeout is designed so that after there is no traffic to the Internet for a pre-configured amount of time, the connection will automatically be disconnected. IP Address and Network (Subnet) Mask: IP stands for Internet Protocol. An IP address consists of a series of four numbers separated by periods, that identifies a single, unique Internet computer host in an IP network. Example: 192.168.2.1. It consists of 2 portions: the IP network address, and the host identifier. The IP address is a 32-bit binary pattern, which can be represented as four cascaded decimal numbers separated by .: aaa.aaa.aaa.aaa, where each aaa can be anything from 000 to 255, or as four cascaded binary numbers separated by .:

bbbbbbbb.bbbbbbbb.bbbbbbbb.bbbbbbbb, where each b can either be 0 or 1. A network mask is also a 32-bit binary pattern, and consists of consecutive leading 72 1s followed by consecutive trailing 0s, such as 11111111.11111111.11111111.00000000. Therefore sometimes a network mask can also be described simply as x number of leading 1s. When both are represented side by side in their binary forms, all bits in the IP address that correspond to 1s in the network mask become part of the IP network address, and the remaining bits correspond to the host ID. For example, if the IP address for a device is, in its binary form, 11011001.10110000.10010000.00000111, and if its network mask is, 11111111.11111111.11110000.00000000 It means the devices network address is 11011001.10110000.10010000.00000000, and its host ID is, 00000000.00000000.00000000.00000111. This is a convenient and efficient method for access points to route IP packets to their destination. ISP Gateway Address: (see ISP for definition). The ISP Gateway Address is an IP address for the Internet access point located at the ISP's office. ISP: Internet Service Provider. An ISP is a business that provides connectivity to the Internet for individuals and other businesses or organizations. LAN: Local Area Network. A LAN is a group of computers and devices connected together in a relatively small area (such as a house or an office). Your home network is considered a LAN. MAC Address: MAC stands for Media Access Control. A MAC address is the hardware address of a device connected to a network. The MAC address is a unique identifier for a device with an Ethernet interface. It is comprised of two parts: 3 bytes of data that corresponds to the Manufacturer ID (unique for each manufacturer), plus 3 bytes that are often used as the products serial number. NAT: Network Address Translation. This process allows all of the computers on your home network to use one IP address. Using the broadband access points NAT capability, you can access the Internet from any computer on your home network without having to purchase more IP addresses from your ISP. Port: Network Clients (LAN PC) uses port numbers to distinguish one network application/protocol over another. Below is a list of common applications and protocol/port numbers:

73 Application Protocol Port Number Telnet FTP SMTP POP3 H.323 TCP TCP TCP 23 21 25 TCP 110 TCP 1720 SNMP UCP 161 SNMP Trap UDP 162 HTTP PPTP TCP 80 TCP 1723 PC Anywhere TCP 5631 PC Anywhere UDP 5632 PPPoE: Point-to-Point Protocol over Ethernet. Point-to-Point Protocol is a secure data transmission method originally created for dial-up connections; PPPoE is for Ethernet connections. PPPoE relies on two widely accepted standards, Ethernet and the Point-to-Point Protocol. It is a communications protocol for transmitting information over Ethernet between different manufacturers Protocol: A protocol is a set of rules for interaction agreed upon between multiple parties so that when they interface with each other based on such a protocol, the interpretation of their behavior is well defined and can be made objectively, without confusion or misunderstanding. Access point: A access point is an intelligent network device that forwards packets between different networks based on network layer address information such as IP addresses. Subnet Mask: A subnet mask, which may be a part of the TCP/IP information provided by your ISP, is a set of four numbers (e.g. 255.255.255.0) configured like an IP address. It is used to create IP address numbers used only within a particular network (as opposed to valid IP address numbers recognized by the Internet, which must be assigned by InterNIC). TCP/IP, UDP: Transmission Control Protocol/Internet Protocol (TCP/IP) and 74 Unreliable Datagram Protocol (UDP). TCP/IP is the standard protocol for data transmission over the Internet. Both TCP and UDP are transport layer protocol. TCP performs proper error detection and error recovery, and thus is reliable. UDP on the other hand is not reliable. They both run on top of the IP (Internet Protocol), a network layer protocol. WAN: Wide Area Network. A network that connects computers located in geographically separate areas (e.g. different buildings, cities, countries). The Internet is a wide area network. Web-based management Graphical User Interface (GUI): Many devices support a graphical user interface that is based on the web browser. This means the user can use the familiar Netscape or Microsoft Internet Explorer to Control/configure or monitor the device being managed. 75