880022..1111gg WWiirreelleessss LLAANN PPCCII CCaarrdd User Manual Version: 1.0
(April, 2004) COPYRIGHT Copyright 2004/2005 by this company. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, this company reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes. All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna. 2. 3. Connect the equipment into an outlet on a circuit different from that to which the Increase the separation between the equipment and receiver. receiver is connected. 4. Consult the dealer or an experienced radio technician for help. FCC Caution This equipment must be installed and operated in accordance with provided instructions and a minimum 20 cm spacing must be provided between computer mounted antenna and persons body (excluding extremities of hands, wrist and feet) during wireless modes of operation. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment. Federal Communication Commission (FCC) Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE) The R&TTE Directive repeals and replaces in the directive 98/13/EEC
(Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000. Safety This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment. EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxembourg, the Netherlands, Portugal, Spain, Sweden, and the United Kingdom. The ETSI version of this device is also authorized for use in EFTA member states:
Iceland, Liechtenstein, Norway, and Switzerland. EU Countries Not intended for use None. 1 INTRODUCTION............................................................................. 1 CONTENTS 1.1 Features......................................................................................................................... 1 1.2 Specifications................................................................................................................ 1 1.3 Package Contents.......................................................................................................... 2 2 INSTALLATION PROCEDURE ..................................................... 3 3 CONFIGURATION UTILITY ......................................................... 3 3.1 Site Survey.................................................................................................................... 6 3.2 Profile............................................................................................................................ 7 3.2.1 Configure the Profile ................................................................................................ 8 3.2.2 Enable WPA in Windows XP ...................................................................................12 3.3 Link Status .................................................................................................................. 14 3.4 Statistics ...................................................................................................................... 15 3.5 Advance ...................................................................................................................... 16 3.6 About........................................................................................................................... 17 4 TROUBLESHOOTING .................................................................. 18 1 Introduction Thank you for purchasing the 802.11g Wireless LAN PCI Card. This card complies with IEEE 802.11g standard, which supports up to 54Mbps high-speed wireless network connections. It can also work with IEEE 802.11b devices. When the card connects to 11b devices, the link speed will be up to 11Mbps. For WLAN security issues, this card supports 64/128-bit WEP data encryption that protects your wireless network from eavesdropping. It also supports WPA (Wi-Fi Protected Access) feature that combines IEEE 802.1x and TKIP (Temporal Key Integrity Protocol) technologies. Client users are required to authorize before accessing to APs or AP Routers, and the data transmitted in the network is encrypted/decrypted by a dynamically changed secret key. This card has built-in AES engine which ensure the highest degree of security and authenticity for digital information and it is the most advanced solution defined by IEEE 802.11i for the security in the wireless network. The power consumption of the card is also very low. Furthermore, this card provides several levels of power saving modes allowing user customizes the way of saving the power from his/her portable or handheld devices. This card is cost-effective, together with the versatile features; it is the best solution for you to build your wireless network. 1.1 Features Works with both IEEE 802.11b and IEEE 802.11g products. High-speed transfer data rate - up to 54Mbps. High throughput supports multi-media data bandwidth requirement. Supports 64/128-bit WEP, WPA (TKIP with IEEE 802.1x) and AES functions for high level of security. Detachable antenna with long length cable provides convenience to locate the antenna. Automatic fallback increases data security and reliability. Supports the most popular operating system: Windows 98SE/Me/2000/XP. Supports 32-bit PCI interface. 1.2 Specifications Interface: 32-bit PCI Standard: IEEE 802.11g/b Frequency Band: 2.4000 ~ 2.4835GHz (Industrial Scientific Medical Band) Modulation: OFDM with BPSK, QPSK, 16QAM, 64QAM (11g) BPSK, QPSK, CCK (11b) Data Rate: 54/48/36/24/18/12/11/9/6/5.5/2/1Mbps auto fallback 1 Security: 64/128-bit WEP Data Encryption, WPA, AES and IEEE 802.1x Antenna: External detachable dipole antenna (Connector: RP-SMA connector, Cable Length:
94 cm) LEDs: TX/RX, Link Drivers: Windows 98SE/Me/2000/XP Transmit Power: 16dBm~18dBm Power consumption: Tx: 350mA, Rx: 250mA Receive Sensitivity: 54Mbps OFDM, 10% PER, -70dBm, 11Mbps CCK, 8% PER, -86dBm, 1Mbps BPSK, 8% PER, -92dBm Dimension: 19(H) x 127(W) x 121(D) mm Temperature: 32~131F (0 ~55C) Humidity: Max. 95% (NonCondensing) Certification: FCC, CE 1.3 Package Contents Before you begin the installation, please check the items of your package. The package should include the following items:
One PCI Card One Extendable Antenna (94cm) One CD (Driver/Utility/Users Manual) One Quick Guide If any of the above items is missing, contact your supplier as soon as possible. 2 2 Installation Procedure Before you proceed with the installation, please notice following descriptions. Note1: The following installation was operated under Windows XP. (Procedures are similar for Windows 98SE/Me/2000.) Note2: If you have installed the Wireless PCI Card driver & utility before, please uninstall the old version first. Hardware Installation A. Turn off your computer and remove its cover. B. Insert the PCI card to an available PCI slot firmly. C. Secure this card to the rear of the computer chassis and put back the cover. D. Secure the antenna to the antenna connector of the card. E. Turn on the computer. Software Installation A. A Found New Hardware Wizard is displayed after the PCI card is installed and the computer is restarted. Click Cancel. B. Insert the Installation CD to your CD-ROM Drive. Execute the setup program. 3 C. Click Easy Install or Next to continue. D. The system starts to install the software of the card. Please wait a moment. E. The current setting of the Country Channel of the card is displayed for your reference. If you are in different country, please change the Country Channel from the drop-down menu and click Next. 4 F. Click Finish to complete the installation. G. The RaConfig is displayed and you can start to configure the card. 5 3 Configuration Utility The Configuration Utility is a powerful application that helps you configure the PCI card and monitor the link status and the statistics during the communication process. The Configuration Utility appears as an icon on the system tray of Windows while the card is running. You can open it by double-click on the icon. Right click the icon, there are some items for you to operate the configuration utility.
Lauch Config Utilities Select Lauch Config Utilities to open the Configuration Utility tool.
Exit Select Exit to close the Configuration Utility tool. 3.1 Site Survey When you open the Configuration Utility, the system will scan all the channels to find all the access points/stations within the accessible range of your card and automatically connect to the wireless device with the highest signal strength. From the Site Survey option, all the networks nearby will be listed. You can change the connection to another networks or add one of the networks to your own profile list. 6 Parameter Available Networks Rescan Button Connect Button Add to Profile Button 3.2 Profile Description This list shows all available wireless networks within range of your card. It also displays the information of the networks including the SSID, BSSID, Signal Strength, Channel, Encryption, Authentication and Network Type. If you want to connect to any networks on the list, double-click the item on the list, and the card will automatically connect to the selected network. Click Rescan button to collect the information of all the wireless networks nearby. Click Connect to connect to the selected network. Add the selected network to Profiles list. The Profiles List is for you to manage the networks you connect to frequently. You are able to Add/Delete/Edit/Activate a profile. Parameter Profiles List Add/Delete/Edit Button Activate Button Description The profiles list display all the profiles and the relative information including Profile Name, SSID, Channel, etc. Click these buttons to add/delete/edit the selected profiles. Click Activate to connect to the selected profile. 7 3.2.1 Configure the Profile System Configuration Parameter Profile Name SSID Power Saving Mode Description Define a recognizable profile name for you to identify the different networks. The SSID (up to 32 printable ASCII characters) is the unique name identified in a WLAN. The ID prevents the unintentional merging of two co-located WLANs. You may specify a SSID for the card and then only the device with the same SSID can interconnect to the card. If you want to add one of the networks nearby to the profile list, pull down the menu, all the networks nearby will be listed and you can add one of them to the profile list. The power saving function is only available when the network type is in Infrastructure. CAM(Constantly Awake Mode) The card will always set in active mode. Power Saving Mode Enable the card in the power saving mode when it is idle. CAM When AC Power Select this option to automatically switch the card from power saving mode to CAM mode while the power of your desktop computer is supplied by the AC power but not battery. 8 Parameter Network Type Transmit Power 11B Preamble Type RTS Threshold Fragment Threshold Channel Description Infrastructure This operation mode requires the presence of an 802.11 Access Point. All communication is done via the Access Point or Router. Ad-Hoc Select this mode if you want to connect to another wireless stations in the Wireless LAN network without through an Access Point or Router. If you want to lower the transmit power of the card for saving the power of the system, you can select the lower percentages from the list. The preamble defines the length of the CRC block for communication among wireless stations. This option is only active in the Ad Hoc network. There are two modes including Auto and Long Preamble. If Auto mode is selected, the card will auto switch the preamble mode depending on the wireless stations which the card is connecting to. Minimum packet size required for an RTS (Request To Send). For packets smaller than this threshold, an RTS is not sent and the packet is transmitted directly to the wireless network. Select a setting within a range of 0 to 2312 bytes. Minor change is recommended. The value defines the maximum size of packets; any packet size larger than the value will be fragmented. If you have decreased this value and experience high packet error rates, you can increase it again, but it will likely decrease overall network performance. Select a setting within a range of 256 to 2312 bytes. Minor change is recommended. This setting is only available for Ad Hoc mode. Select the number of the radio channel used for the networking. The channel setting should be the same with the network you are connecting to. 9 Authentication vs. Security Parameter Authentication Type Description This setting has to be consistent with the wireless networks that the card intends to connect. None No authentication is needed among the wireless network. Shared Only wireless stations using a shared key (WEP Key identified) are allowed to connecting each other. WPA-PSK It is a special mode designed for home and small business users who do not have access to network authentication servers. In this mode, known as Pre-Shared Key, the user manually enters the starting password in their access point or gateway, as well as in each wireless stations in the network. WPA takes over automatically from that point, keeping unauthorized users that don't have the matching password from joining the network, while encrypting the data traveling between authorized devices. The encryption methods are including TKIP and AES. Note that this option is only available for Windows XP. 10 Parameter Encryption Mode WPA Pre-Shared Key WEP Key
(Key1 ~ Key4) Description None Disable the WEP Data Encryption. WEP Enable the WEP Data Encryption. When the item is selected, you have to continue setting the WEP Encryption keys. TKIP TKIP (Temporal Key Integrity Protocol) changes the temporal key every 10,000 packets (a packet is a kind of message transmitted over a network.) This insures much greater security than the standard WEP security. AES AES has been developed to ensure the highest degree of security and authenticity for digital information and it is the most advanced solution defined by IEEE 802.11i for the security in the wireless network. Note: All devices in the network should use the same encryption method to ensure the communication. The WPA-PSK key can be from eight to 64 characters and can be letters or numbers. This same key must be used on all of the wireless stations in the network. The WEP keys are used to encrypt data transmitted in the wireless network. There are two types of key length: 64-bit and 128-bit. Select the default encryption key from Key 1 to Key 4 by selected the radio button. Fill the text box by following the rules below. 64-bit Input 10-digit Hex values (in the A-F, a-f and 0-9 range) or 5-digit ASCII characters (including a-z and 0-9) as the encryption keys. For example: 0123456aef or test1. 128-bit Input 26-digit Hex values (in the A-F, a-f and 0-9 range) or 13-digit ASCII characters (including a-z and 0-9) as the encryption keys. For example:
01234567890123456789abcdef or administrator. 11 3.2.2 Enable WPA in Windows XP Wi-Fi Protected Access (WPA) is a specification of standards-based, interoperable security enhancement that strongly increases the level of data protection (encryption) and access control
(authentication) for existing and future wireless LAN systems. The technical components of WPA include Temporal Key Integrity Protocol (TKIP) for dynamic key exchange, and 802.1x for authentication. There are two types of WPA security: WPA-PSK (no server) and WPA (with server). WPA requires a Radius Server to complete the authentication among wireless stations and Access Points. Typically, this mode is used in an enterprise environment. WPA-PSK uses a so-called pre-shared key as the security key. A pre-shared key is a password that each wireless station uses the same key to access the network. Typically, this mode will be used in a home environment. To enable the WPA function in Windows XP, the following software systems are required:
1. Windows XP Service Pack 1 with Windows XP Support Patch for Wi-Fi Protected Access program in addition. 2. Configure the card by Wireless built-in utility (Wireless Zero Configuration).
Note: In that kind of system, there are two utility selections when you open the configuration utility of the card. You can select to use the XPs built-in utility with full WPA function. If Use XP Wireless Zero Configuration is selected, you can only configure the advance setting or check the link status and statistics from the RaConfig utility. 12 1. From here, right click the icon to select View Available Wireless Networks. 2. Press Advanced button from Wireless Network Connection. 3. Press Configure button to configure the WPA function for the current network. Note: Uncheck Use Windows to Configure my wireless network settings, the RaConfig utility will be enabled again. Parameter Network Authentication Description Open No authentication is needed among the wireless network. Shared Only wireless stations using a shared key (WEP Key identified) are allowed to connecting each other. WPA This mode is for enterprise with an authentication server
(Radius Server), WPA-enabled access point, and a WPA-enabled client. Once WPA is enabled, all clients and access points on the network must be WPA-enabled in order to access the network. WPA-PSK It is a special mode designed for home and small business users who do not have access to network authentication servers. In this mode, known as Pre-Shared Key, the user manually enters the starting password in their access point or gateway, as well as in each PC on the wireless network. WPA takes over automatically from that point, keeping unauthorized users that don't have the matching password from joining the network, while encrypting the data traveling between authorized devices. 13 Parameter Data Encryption Description WEP In WPA or WPA-PSK mode, WEP is also able to be the encryption method for the transmission data. TKIP TKIP (Temporal Key Integrity Protocol) changes the temporal key every 10,000 packets (a packet is a kind of message transmitted over a network.) This insures much greater security than the standard WEP security. AES AES has been developed to ensure the highest degree of security and authenticity for digital information and it is the most advanced solution defined by IEEE 802.11i for the security in the wireless network. Note: All devices in the network should use the same encryption method to ensure the communication. 3.3 Link Status From the Link Status option, you can view all the information of the network you are connecting to. Parameter Status Current Channel Description Display the SSID and MAC ID of the network the card is connecting to. Display the number of the radio channel and the frequency used for the networking. 14 Parameter Current Tx Rate Throughput (Kbits/sec) Link Quality dBm Signal Strength 3.4 Statistics Description Display the transmission rate of the network. The maximum transmission rate is 54Mbps. Display the speed of data transmitted and received. This bar indicates the quality of the link. The higher the percentage, the better the quality. If you want to know the signal strength in the unit of dBm, select this check box. This bar shows the signal strength level. The higher percentage shown in the bar, the more radio signal been received by the card. This indicator helps to find the proper position of the wireless device for quality network operation. This option enables you to view the available statistic information with its Tx counts (Tx success, Tx error, RTS Success and RTS Failed), and its Rx counts (Rx success, Rx error). You may reset the counters by clicking Reset Counter. 15 3.5 Advance This option enables you to configure more advanced settings, for example: wireless mode, protection mode and etc. Parameter Wireless Mode Tx BURST B/G Protection Description 802.11 B/G mix If you have a mix of 802.11b and 802.11g wireless stations in your network, it is recommended to setting the card to this mode. This mode is also the default setting. 802.11 B only This card can be compatible with both 802.11g and 802.11b wireless stations. If there are only 802.11b wireless stations in the network, you can set the card to this mode. Tx Burst enables the card to deliver the better throughput in the same period and environment. If you have a mix of 802.11b and 802.11g wireless stations in the network, it is recommended to enable the protection mechanism. This mechanism can decrease the rate of data collision between 802.11b and 802.11g wireless stations. When the protection mode is enabled, the throughput of the card will be a little lower due to many of frame traffic should be transmitted. Auto Based on the status of the network and automatically disable/enable protection mode. On Always enable the protection mode. Off Always disable the protection mode. 16 Parameter ADHOC_OFDM Tx Rate Turn Off RF Button 3.6 About Description When the network type is in Ad Hoc mode, that the card can only work in 11b data rate. It is defined by Wi-Fi organization. If you want to enable the data rate up to 54Mbps (11g), select ADHOC_OFDM. There are several options including Auto/1/2/5.5/11/6/9/12/18/24/36/48/54Mbps for you to select. When the Auto is selected, the device will choose the most suitable transmission rate automatically. The higher data rate you designated in the network, the shorter distance is allowed between the card and the wireless stations. When the wireless mode is 802.11 B only, the maximum data rate is 11Mbps (11b) so that there are only Auto/1/2/5.5/11Mbps options you can select. If you want to turn off the radio of the card temporarily, click this button. To turn on the radio, click this button again. By choosing this option, you can click the hyperlink to connect the website for the information of the wireless chipset vendor and review basic information about the Utility such as the Driver, Utility and EEPROM Version. The MAC Address of the card is displayed in the screen as well. 17 4 Troubleshooting This chapter provides solutions to problems usually encountered during the installation and operation of the card. 1. What is the IEEE 802.11g standard?
802.11g is the new IEEE standard for high-speed wireless LAN communications that provides for up to 54 Mbps data rate in the 2.4 GHz band. 802.11g is quickly becoming the next mainstream wireless LAN technology for the home, office and public networks. 802.11g defines the use of the same OFDM modulation technique specified in IEEE 802.11a for the 5 GHz frequency band and applies it in the same 2.4 GHz frequency band as IEEE 802.11b. The 802.11g standard requires backward compatibility with 802.11b. The standard specifically calls for:
A. A new physical layer for the 802.11 Medium Access Control (MAC) in the 2.4 GHz frequency band, known as the extended rate PHY (ERP). The ERP adds OFDM as a mandatory new coding scheme for 6, 12 and 24 Mbps (mandatory speeds), and 18, 36, 48 and 54 Mbps
(optional speeds). The ERP includes the modulation schemes found in 802.11b including CCK for 11 and 5.5 Mbps and Barker code modulation for 2 and 1 Mbps. B. A protection mechanism called RTS/CTS that governs how 802.11g devices and 802.11b devices interoperate. 2. What is the IEEE 802.11b standard The IEEE 802.11b Wireless LAN standard subcommittee, which formulates the standard for the industry. The objective is to enable wireless LAN hardware from different manufactures to communicate. 3. What does IEEE 802.11 feature support The product supports the following IEEE 802.11 functions:
CSMA/CA plus Acknowledge Protocol
Multi-Channel Roaming
Automatic Rate Selection
RTS/CTS Feature
Fragmentation
Power Management 4. What is Ad-hoc An Ad-hoc integrated wireless LAN is a group of computers, each has a Wireless LAN adapter, Connected as an independent wireless LAN. Ad hoc wireless LAN is applicable at a departmental scale for a branch or SOHO operation. 5. What is Infrastructure An integrated wireless and wireless and wired LAN is called an Infrastructure configuration. Infrastructure is applicable to enterprise scale for wireless access to central database, or wireless application for mobile workers. 18 6. What is BSS ID A specific Ad hoc LAN is called a Basic Service Set (BSS). Computers in a BSS must be configured with the same BSS ID. 7. What is WEP WEP is Wired Equivalent Privacy, a data privacy mechanism based on a 40 bit shared key algorithm, as described in the IEEE 802 .11 standard. 8. What is TKIP?
TKIP is a quick-fix method to quickly overcome the inherent weaknesses in WEP security, especially the reuse of encryption keys. TKIP is involved in the IEEE 802.11i WLAN security standard, and the specification might be officially released by early 2003. 9. What is AES?
AES (Advanced Encryption Standard), a chip-based security, has been developed to ensure the highest degree of security and authenticity for digital information, wherever and however communicated or stored, while making more efficient use of hardware and/or software than previous encryption standards. It is also included in IEEE 802.11i standard. Compare with AES, TKIP is a temporary protocol for replacing WEP security until manufacturers implement AES at the hardware level. 10. Can Wireless products support printer sharing Wireless products perform the same function as LAN products. Therefore, Wireless products can work with Netware, Windows 2000, or other LAN operating systems to support printer or file sharing. 11. Would the information be intercepted while transmitting on air WLAN features two-fold protection in security. On the hardware side, as with Direct Sequence Spread Spectrum technology, it has the inherent security feature of scrambling. On the software side, WLAN series offer the encryption function (WEP) to enhance security and Access Control. Users can set it up depending upon their needs. 12. What is DSSSWhat is FHSSAnd what are their differences Frequency-hopping spread-spectrum (FHSS) uses a narrowband carrier that changes frequency in a pattern that is known to both transmitter and receiver. Properly synchronized, the net effect is to maintain a single logical channel. To an unintended receiver, FHSS appears to be short-duration impulse noise. Direct-sequence spread-spectrum (DSSS) generates a redundant bit pattern for each bit to be transmitted. This bit pattern is called a chip (or chipping code). The longer the chip is, the greater the probability that the original data can be recovered. Even if one or more bits in the chip are damaged during transmission, statistical techniques embedded in the radio can recover the original data without-the need for retransmission. To an unintended receiver, DSSS appears as low power wideband noise and is rejected (ignored) by most narrowband receivers. 19 13. What is Spread Spectrum Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communication systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband transmission, but the trade off produces a signal that is, in effect, louder and thus easier to detect, provided that the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to the right frequency, a spread spectrum signal looks like background noise. There are two main alternatives, Direct Sequence Spread Spectrum (DSSS) and Frequency Hopping Spread Spectrum (FHSS). 20