AC450 Wireless LAN 11ac Band Extender
(IEEE 802.11a/an/ac) Users Manual Version: 1.0
(Jan, 2016) 1 COPYRIGHT Copyright 2014 by this company. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, this company reserves the right to revise this publication and to make changes from time to time in the contents thereof without obligation to notify any person of such revision or changes. 2 Federal Communication Commission Interference Statement FCC Part 15 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device is restricted to indoor use FCC Caution This equipment must be installed and operated in accordance with provided instructions and a minimum 20 cm spacing must be provided between computer mounted antenna and persons body (excluding extremities of hands, wrist and feet) 3 during wireless modes of operation. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment. This device is restricted to indoor use Federal Communication Commission (FCC) Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 4 R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC
(Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000. Safety This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment. EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxembourg, the Netherlands, Portugal, Spain, Sweden, and the United Kingdom. The ETSI version of this device is also authorized for use in EFTA member states:
Iceland, Liechtenstein, Norway, and Switzerland. EU Countries Not intended for use None. 5 CATALOG 1-1 Introduction and safety information ........................................................................ 7 1-2 Safety Information ........................................................................................... 7 1-3 Package Contents ............................................................................................. 8 1.4 Applications ..................................................................................................... 8 1-5 Familiar with your new 11ac Band Extender .................................................. 9 Chapter II: System and Network Setup ........................................................................ 10 2-1 Build network connection .............................................................................. 10 Chapter III WEB GUI configuration ........................................................................... 11 3-1 Setup Wizard.................................................................................................. 11 3-1-1 Client mode ..................................................................................... 11 3-2 Advanced Setup ............................................................................................. 15 3-3 WPS Setup ..................................................................................................... 17 Chapter IV: Appendix................................................................................................... 19 4-1 Hardware Specification ................................................................................. 19 4-3 Glossary ......................................................................................................... 20 6 Chapter I: Product Information 1-1 Introduction and safety information AC450 Wireless LAN 11ac Band Extender is an 802.11ac certified client adapter enabling only IPTV Set-Top Box with an Ethernet interface to connect to a standard 11ac Wi-Fi router/AP wirelessly. AC450 Wireless LAN 11ac Band Extender includes a WPS (Wi-Fi Protection Setup) button for simple and quick connection to a standard Wi-Fi Router/Access Point. Users can enjoy the robust high speed 11ac Wi-Fi connection instantly without the need to download software drivers or login in to the device. 1-2 Safety Information In order to keep the safety of users and your properties, please follow the following safety instructions:
1. This band extender is designed for indoor use only; DO NOT place this band extender outdoor. 2. DO NOT put this band extender at or near hot or humid places, like kitchen or bathroom. Also, do not left this band extender in the car in summer. 3. DO NOT plug, unplug & rotation LAN port with force. 4. If you want to place this band extender at high places or hang on the wall, please make sure the band extender is firmly secured. Falling from high places would damage the band extender and its accessories, and warranty will be void. 5. Accessories of this band extender, like antenna, cable and power supply, are danger to small children under 3 years old. They may put the small parts in their nose or month and it could cause serious damage to them. KEEP THIS BAND EXTENDER OUT THE REACH OF CHILDREN!
6. The band extender will become hot when being used for long time (This is normal and is not a malfunction). DO NOT put this band extender on paper, cloth, or other flammable materials. 7 7. Theres no user-serviceable part inside the band extender. If you found that the product is not working properly, please contact your dealer of purchase and ask for help. DO NOT disassemble the producy, warranty will be void. 8. If the product falls into water when its powered, DO NOT use your hand to pick it up. Switch the electrical power off before you do anything, or contact an experienced technician for help. 9. If you smell something strange, or even see some smoke coming out from the product or power supply, remove the power supply or switch the electrical power off immediately, and call dealer of purchase for help. 1-3 Package Contents Before starting to use this 11ac band extender, please check if theres anything missing in the package, and contact your dealer of purchase to claim for missing items:
11ac Band Extender (1 pcs) Quick Installation Guide (1 pcs) User Manual CD-ROM (1 pcs) 1-4 Applications AC450 Wireless LAN 11ac Band Extender can ONLY be used as a Wi-Fi client connecting ONLY SmarTV and STB to a standard 802.11ac Wi-Fi Router/AP wirelessly. (The device is restricted by the Software and the device will not be activated as an AP at all) IPTV Set-Top-Box for Multicast Linear Video streaming Enhancing Wi-Fi connection speed (upto 100mbps) on a SmarTV for high quality streaming of HD video Connecting a VoIP SIP phone to the Wi-Fi Router Wirelessly 8 1-5 Familiar with your new 11ac Band Extender LED indication & Button Function SMA for Antenna LED indicate RJ-45 Ethernet Micro USB for power Reset/WPS LED Definition Function Definition Indication Client mode
(Blue) Blinking: Wireless LAN activity RJ-45 Client mode: LAN Port
(transferring or receiving data) Ethernet Micro USB For 11ac band extender power Connector supply only. System status On Solid: Detect WPS button is pressed and hold for more 3 WPS /
Reset WPS: Pressed and hold for more 3 seconds to start WPS.
(Purple) seconds, Wireless WPS function is enabled. Reset: Pressed and hold for more 10 seconds, till LED is blinking to Blinking: Detect Reset button is do restore all settings to factory pressed and hold for more 10 defaults. seconds. (do restore all settings to factory defaults). 9 Chapter II: System and Network Setup 2-1 Build network connection Locate the WPS button and/or determine how to activate the WPS process on the Wi-Fi Router/AP. 1. Activate the WPS process in the AP/Router 2. Within less than 1 minute: press and hold the WPS button on the AC450 band extender for 3 seconds or until the LED color is solid purple 3. The LED on AC450 band extender will turn solid blue once the wireless connection is established NOTE: If you cant see the web management interface, and youre being prompted to input user name and password again, it means you didnt input username and password correctly. Please retype user name and password again. If youre certain about the user name and password you type are correct, please go to 4-2 Troubleshooting to perform a factory reset, to set the password back to default value. TIP: This page shows the four major setting categories: Setup Wizard, Advanced Setup, WPS Setup and Status. You can find the shortcut which leads to these setting categories at the upper-right corner of every page, and you can jump to another category directly by clicking the link, and dont have to go back to the first page. 10 Chapter III WEB GUI configuration 3-1 Setup Wizard The setup wizard will guide you to configure 11ac Band Extender for first time. Please follow the setup wizard step by step. Welcome to Setup Wizard, please click Next. 3-1-1 Client mode In Client mode, it can let your networking device have wireless capability;
it will become your networking device's wireless network card. You can connect this device to RJ-45 Ethernet port of your existing Internet TV or Set Top Box. Please select Client mode, then click Next. 11 Wireless Site Survey: Please click Site Survey button to find WiFi AP in your area. This page provides tool to scan the wireless network. If any Access Point or IBSS is found, you could choose to connect it manually. Please select a Root wireless AP and click Next. 12 Root AP Wireless Security Key: Please setting encryption for the Root AP just you selected, then click Connect when you finish. Connect Successfully: Please press Reboot Now to restart the Band Extender to make the changes take effect. 13 Add the URL to your bookmark (my favorite list) Default: "Save"
(we recommend you to save it for quick access to the Web setting page next time)
(Supports IE and Firefox only. Please add the access key to the bookmark manually if you use other browsers) 14 3-2 Advanced Setup This page allows you setting Password and Firmware upgrade to new version. Please note: do not power off the device during the Firmware upgrade because it may crash the system. 15 Password Settings: You can change the User Name and Password required while logging into the Band Extender's web-based management system. By default, the password is 1234. So please assign a password to the Administrator as soon as possible, and store it in a safe place. Passwords can contain 1 to 30 alphanumeric characters, and are case sensitive. Firmware Upgrade: This tool allows you to upgrade the Band Extender's system firmware. Enter the path and name of the upgrade file and then click the APPLY button below. You will be prompted to confirm the upgrade. The system will automatically reboot after you finished the firmware upgrade process. Please note: Do not power off the device during the Firmware upgrade because it may crash the system. 16 NOTE: Never interrupt the upgrade procedure by closing the web browser or physically disconnect your computer from Band Extender. If the firmware you uploaded is corrupt, the firmware upgrade will fail, and you may have to return this product to the dealer of purchase to ask for help. (Warranty voids if you interrupted the upgrade procedure). 3-3 WPS Setup This page allows you to change the setting for WPS (Wi-Fi Protected Setup). WPS can help your wireless client automatically connect to the Root Access Point. 17 18 Chapter IV: Appendix 4-1 Hardware Specification CPU: REALTEK RTL8881AM RF: REALTEK RTL8881AM Flash: 2MB SDRAM RAM: 8MB (CPU inside) LAN Port: 10/100M Port x 1 Antenna: External Dipole Antenna x 1 (5G) Power: DC 5V/0.5A USB port power or 5V/0.6A Switching Power Adapter Dimension: 60 (L) x 50 (W) x 23 (D) mm (without ANT) Temperature: Operating: 0~40C Storage: -20~60C Humidity: Operating: 10~90% (Non-Condensing) Storage: Max.95% (NonCondensing) Certification: FCC 19 4-2 Troubleshooting If you found the device is working improperly or stop responding to you, dont panic! Before you contact your dealer of purchase for help, please read this troubleshooting first. Some problems can be solved by you within very short time!
Scenario Device become hot Solution a. This is not a malfunction, if you can keep your hand on the devices case. b. If you smell something wrong or see the smoke coming out from device or A/C power adapter, please disconnect the device and A/C power adapter from utility power
(make sure its safe before youre doing this!), and call your dealer of purchase for help. 4-3 Glossary Ethernet: A standard for computer networks. Ethernet networks are connected by special cables and hubs, and move data around at up to 10/100 million bits per second
(Mbps). Idle Timeout: Idle Timeout is designed so that after there is no traffic to the Internet for a pre-configured amount of time, the connection will automatically be disconnected. IP Address and Network (Subnet) Mask: IP stands for Internet Protocol. An IP address consists of a series of four numbers separated by periods, which identifies a single, unique Internet computer host in an IP network. Example: 192.168.2.1. It consists of 2 portions: the IP network address, and the host identifier. The IP address is a 32-bit binary pattern, which can be represented as four cascaded decimal numbers separated by .: aaa.aaa.aaa.aaa, where each aaa can be anything from 000 to 255, or as four cascaded binary numbers separated by .:
bbbbbbbb.bbbbbbbb.bbbbbbbb.bbbbbbbb, where each b can either be 0 or 1. A network mask is also a 32-bit binary pattern, and consists of consecutive leading 1s followed by consecutive trailing 0s, such as 11111111.11111111.11111111.00000000. Therefore sometimes a network mask can 20 also be described simply as x number of leading 1s. When both are represented side by side in their binary forms, all bits in the IP address that correspond to 1s in the network mask become part of the IP network address, and the remaining bits correspond to the host ID. For example, if the IP address for a device is, in its binary form, 11011001.10110000.10010000.00000111, and if its network mask is, 11111111.11111111.11110000.00000000 It means the devices network address is 11011001.10110000.10010000.00000000, and its host ID is, 00000000.00000000.00000000.00000111. This is a convenient and efficient method for routers to route IP packets to their destination. LAN: Local Area Network. A LAN is a group of computers and devices connected together in a relatively small area (such as a house or an office). Your home network is considered a LAN. MAC Address: MAC stands for Media Access Control. A MAC address is the hardware address of a device connected to a network. The MAC address is a unique identifier for a device with an Ethernet interface. It is comprised of two parts: 3 bytes of data that corresponds to the Manufacturer ID (unique for each manufacturer), plus 3 bytes that are often used as the products serial number. NAT: Network Address Translation. This process allows all of the computers on your home network to use one IP address. Using the broadband routers NAT capability, you can access the Internet from any computer on your home network without having to purchase more IP addresses from your ISP. Port: Network Clients (LAN PC) uses port numbers to distinguish one network application/protocol over another. Below is a list of common applications and protocol/port numbers:
Application Protocol Port Number Telnet FTP SMTP POP3 H.323 TCP TCP TCP 23 21 25 TCP 110 TCP 1720 21 SNMP UCP 161 SNMP Trap UDP 162 HTTP PPTP TCP 80 TCP 1723 PC Anywhere TCP 5631 PC Anywhere UDP 5632 Protocol: A protocol is a set of rules for interaction agreed upon between multiple parties so that when they interface with each other based on such a protocol, the interpretation of their behavior is well defined and can be made objectively, without confusion or misunderstanding. Router: A router is an intelligent network device that forwards packets between different networks based on network layer address information such as IP addresses. Subnet Mask: A subnet mask, which may be a part of the TCP/IP information provided by your ISP, is a set of four numbers (e.g. 255.255.255.0) configured like an IP address. It is used to create IP address numbers used only within a particular network (as opposed to valid IP address numbers recognized by the Internet, which must be assigned by InterNIC). TCP/IP, UDP: Transmission Control Protocol/Internet Protocol (TCP/IP) and Unreliable Datagram Protocol (UDP). TCP/IP is the standard protocol for data transmission over the Internet. Both TCP and UDP are transport layer protocol. TCP performs proper error detection and error recovery, and thus is reliable. UDP on the other hand is not reliable. They both run on top of the IP (Internet Protocol), a network layer protocol. WAN: Wide Area Network. A network that connects computers located in geographically separate areas (e.g. different buildings, cities, countries). The Internet is a wide area network. Web-based management Graphical User Interface (GUI): Many devices support a graphical user interface that is based on the web browser. This means the user can use the familiar Netscape or Microsoft Internet Explorer to Control/configure or monitor the device being managed. 22