all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
user manual | Users Manual | 5.07 MiB | December 01 2015 | |||
1 | Internal Photos | December 01 2015 | ||||||
1 | Cover Letter(s) | December 01 2015 | ||||||
1 | RF Exposure Info | December 01 2015 | ||||||
1 | Cover Letter(s) | December 01 2015 | ||||||
1 | Test Report | December 01 2015 | ||||||
1 | Cover Letter(s) | December 01 2015 | ||||||
1 | External Photos | December 01 2015 | ||||||
1 | ID Label/Location Info | December 01 2015 | ||||||
1 | Test Setup Photos | December 01 2015 |
1 | user manual | Users Manual | 5.07 MiB | December 01 2015 |
N300 Wireless LAN 11n Ceiling-Mount Access Point Users Manual EW-7679WAUser Manua Version: 1.0
(October, 2014) CONTENTS I. Product Information .............................................................................. 4 I-1. I-2. I-3. I-4. I-5. I-6. I-7. Package Contents .................................................................................................................. 4 System Requirements ............................................................................................................ 4 Hardware Overview ............................................................................................................... 5 LED Status .............................................................................................................................. 6 Reset ...................................................................................................................................... 7 Multi-Region Power Adapter ................................................................................................. 8 Safety Information ................................................................................................................. 9 II. Quick Setup .......................................................................................... 10 II-1. II-2. II-3. Initial Setup .......................................................................................................................... 10 Basic Settings ....................................................................................................................... 12 Wi-Fi Protected Setup (WPS) ............................................................................................... 15 III. Hardware Installation ........................................................................... 16 III-1. III-2. III-3. Connecting the access point to a router or PoE switch ..................................................... 16 Mounting the access point to a ceiling .............................................................................. 18 T-Rail Mount ...................................................................................................................... 21 IV. Browser Based Configuration Interface ................................................. 23 IV-1. System Setup ..................................................................................................................... 25 IV-1-1. Status ................................................................................................................................. 25 IV-1-2. LAN Settings ....................................................................................................................... 27 IV-1-3. System Log ......................................................................................................................... 29 IV-2. Wireless Setting ................................................................................................................. 30 IV-2-1. Status ................................................................................................................................. 30 IV-2-2. 2.4GHz ................................................................................................................................ 32 IV-2-2-1. IV-2-2-2. IV-2-2-3. Basic ............................................................................................................................. 32 Advanced ..................................................................................................................... 34 Security ........................................................................................................................ 36 IV-2-2-3-1. Disable ......................................................................................................................... 38 IV-2-2-3-2. WEP ............................................................................................................................ 38 IV-2-2-3-3. WPA Pre-shared Key .................................................................................................. 39 IV-2-2-3-4. WPA RADIUS .............................................................................................................. 39 IV-2-2-3-5. 802.1x (WEP) .............................................................................................................. 40 IV-2-3. MAC Filter .......................................................................................................................... 41 III-2-3-1. WPS ....................................................................................................................................42 IV-2-3-2. Client List ............................................................................................................................ 44 2 IV-3. IV-3-1. IV-3-2. IV-3-3. Toolbox ............................................................................................................................... 45 Admin ................................................................................................................................. 41 Time Setting ....................................................................................................................... 42 Diagnosis ............................................................................................................................ 44 IV-3-4. Firmware .............................................................................................................................. 45 IV-3-5. System Setting...................................................................................................................... 45 IV-3-6. Reboot .................................................................................................................................. 46 IV. Appendix ............................................................................................. 51 IV-1. Configuring your IP address ............................................................................................... 51 IV-1-2-1. IV-1-2-2. IV-1-2-3. IV-1-2-4. IV-1-2-5. Windows XP ............................................................................................................... 52 Windows Vista ........................................................................................................... 54 Windows 7 ................................................................................................................. 56 Windows 8 ................................................................................................................. 60 Mac ............................................................................................................................ 64 IV-1-5. Glossary................................................................................................................................ 66 3 I. Product Information I-1. Package Contents 2 3 5 1. Access Point 2. Ceiling Mount Bracket 3. T-Rail Mounting Kit &
4. Quick Installation Guide 5. Power Adapter (see I-6. Multi-Region Power Adapter) Screws 1 4 I-2. System Requirements
- Existing cable/DSL modem & router
- Computer with web browser for access point configuration 4 I-3. Hardware Overview 5 Ethernet Port Power Port I-4. LED Status 6 Blue Amber Off On On Long Flashing Short Flashing Off On Off OFF Off Status AP is off Booting up, Going to Reboot AP is up and every function working properly Firmware upgrading Ready to reset to factory default Off Flashing Error I-5. Reset If you experience problems with your access point, you can reset the device back to its factory settings. This resets all settings back to default. 1. Press and hold the reset button on the access point for at least 10 seconds then release the button. You may need to use a pencil or similar sharp object to push the reset button. 2. Wait for the access point to restart. The access point is ready for setup when the LED is blue. 7 I-6. Multi-Region Power Adapter The included power adapter has four changeable heads for different AC sockets according to your region. 8 I-7. Safety Information In order to ensure the safe operation of the device and its users, please read and act in accordance with the following safety instructions. 1. The access point is designed for indoor use only; do not place the access point outdoors. 2. Do not place the access point in or near hot/humid places, such as a kitchen or bathroom. 3. Do not pull any connected cable with force; carefully disconnect it from the access point. 4. Handle the access point with care. Accidental damage will void the warranty of the access point. 5. The device contains small parts which are a danger to small children under 3 years old. Please keep the access point out of reach of children. 6. Do not place the access point on paper, cloth, or other flammable materials. The access point may become hot during use. 7. There are no user-serviceable parts inside the access point. If you experience problems with the access point, please contact your dealer of purchase and ask for help. 8. The access point is an electrical device and as such, if it becomes wet for any reason, do not attempt to touch it without switching the power supply off. Contact an experienced electrical technician for further help. 9. If you smell burning or see smoke coming from the access point or power adapter, then disconnect the access point and power adapter immediately, as far as it is safely possible to do so. Call your dealer of purchase for help. 9 I. Quick Setup Please follow the instructions in the chapters below to setup your access point and then configure its basic settings. Initial Setup II-1. 1. Connect the access point to a computer via Ethernet cable. 2. Connect the power adapter to the access points 12V DC port and plug the power adapter into a power supply. 3. Please wait a moment for the access point to start up. The access point is ready when the LED is blue. 4. Set your computers IP address to 192.168.2.x where x is a number in the range 3 100. If you are unsure how to do this, please refer to IV-1. Configuring your IP address for more information. Please ensure there are no other active network connections on your computer (disconnect Wi-Fi connections and Ethernet cables). 5. Enter the access points default IP address 192.168.2.1 into the URL bar of a web browser. 10 6. You will be prompted for a username and password. Enter the default username admin and the default password admin. 7. You will arrive the System Information screen shown below. 8. Next, please follow the instructions below in II-1. Basic Settings to configure the access points basic settings. 11 For more advanced configurations, please refer to IV. Browser Based Configuration Interface. Basic Settings II-2. The instructions below will help you to configure the following basic settings of the access point:
It is recommended you configure these settings before using the access point.
- LAN IP Address
- 2.4GHz SSID & Security
- Login Password
- Time & Date 1. To change the access points LAN IP address, go to Network Settings >
LAN-side IP Address and you will see the screen below. 12 2. Enter the IP address settings you wish to use for your access point. Click Apply to save the changes the wait a few moments for the access point to reload. When you change your access points IP address, you need to use the new IP address to access the browser based configuration interface instead of the default IP 192.168.2.1. 3. To change the SSID and password of your access points wireless network(s), go to Wireless Setting > 2.4GHz > Basic. Enter the new SSID for your 2.4GHz wireless network in the SSID1 field and click Apply. 4. Go to Wireless Setting > 2.4GHz > Security. Enter a new password for your 2.4GHz wireless network in the SSID1 field and click Apply. 13 5. To change the login password for the browser based configuration interface, go to Toolbox > Admin. 6. Complete the Current Password, New Password and Confirm Password fields and click Apply. 7. To set the correct time for your access point, go to Toolbox > Time Setting. 8. Select the correct time zone for your access point from the drop down list. The access point also supports NTP (Network Time Protocol) so alternatively you can enter the host name or IP address of a time server. Click Apply when you are finished. 9. The basic settings of your access point are now configured. Please refer to III. Hardware Installation for guidance on connecting your access point to a router or PoE switch and/or fixing your access point to a ceiling. Or refer to IV. Browser Based Configuration Interface for help with advanced configurations. 14 II-3. Wi-Fi Protected Setup (WPS) Wi-Fi Protected Setup is a simple way to establish connections between WPS compatible devices. After you have set up the access point as explained in II. Installation you can use the WPS button to establish a connection between the access point and a WPS-compatible wireless device/client. 1. Press and hold the WPS/Reset button on the front of the access point for 2 seconds. 2. Within two minutes, activate WPS on your WPS-compatible wireless device. Please check the documentation for your wireless device for information regarding its WPS function. 3. The devices will establish a connection. 15 II. Hardware Installation III-1. Connecting the access point to a router or PoE switch 1. Connect the access point to a router or PoE switch via Ethernet cable. 2. If you are using a router, then connect the power adapter to the access points 12V DC port and plug the power adapter into a power supply. 3. If you are using a PoE (Power over Ethernet) switch then it is not necessary to use the included power adapter, the access point will be powered by the PoE switch. 16 Do not use the power adapter if you are using a PoE switch. 17 III-2. Mounting the access point to a ceiling To mount the access point to a ceiling, please follow the instructions below and refer to diagram A & B. For Wooden Ceilings (refer to diagram A):
1. Place the ceiling mount bracket to a ceiling in your desired location and insert screw iii through hole i (x 2)and tighten to fix the bracket in place. 2. When the ceiling bracket is in place, inset screw iv into hole v (x 2) on the access point. 3. Fix the access point to the ceiling bracket by inserting the attached screws iv into hole vi and twisting the access point. 4. Lock the access point firmly into place when by twisting it to align screws iv with the grooves in the ceiling mount. For Other Ceilings (refer to diagram B):
1. Place the ceiling mount bracket to a ceiling in your desired location and Insert screw ii through hole i (x 2) and tighten to fix the bracket in place, as shown in A. 2. Insert screw iii through hole i and into the rear of screw ii and tighten to provide additional strength. 3. When the ceiling bracket is in place, insert screw iv into hole v (x 2) on the access point. 5. Fix the access point to the ceiling bracket by inserting the attached screws iv into hole vi and twisting the access point. 6. Lock the access point firmly into place by twisting it to align screws iv with the grooves in the ceiling mount. 18 A ii i iii 19 B 20 III-3. T-Rail Mount To mount the access point to a T-Rail, please follow the instructions below and refer to diagram C, D & E. 1. Select the correct size T-Rail bracket from the two sizes which are included in the package contents. 2. Attach the T-Rail bracket i to hole ii using screw iii (x 2) as shown in C. If you need more space between the access point and the T-Rail, then additionally use bracket iv between bracket i and hole ii (x 2), and use the longer screws (x 2) included in the package contents. 3. Clip the access point onto your T-Rail using the now attached T-Rail bracket. 21 22 IV. Browser Based Configuration Interface You can use the browser-based configuration interface to configure advanced settings. 1. Connect a computer to your access point using an Ethernet cable. 2. Enter your access points IP address in the URL bar of a web browser. The access points default IP address is 192.169.2.2. 3. You will be prompted for a username and password. The default username is admin and the default password is admin, though it was recommended that you change the password during setup (see II-2. Basic Settings). If you cannot remember your password, reset the access point back to its factory default settings. Refer to I-5. Reset 4. You will arrive at the System Setup screen shown below. 23 5. Use the menu across the top and down the left side to navigate. 6. Click Apply to save changes and reload the access point, or Cancel to cancel changes. Please wait a few seconds for the access point to reload after you Apply changes, as shown below. 7. Please refer to the following chapters for full descriptions of the browser based configuration interface features. 24 System Setup IV-1. Screenshots displayed are examples. The information shown on your screen will vary depending on your configuration. IV-1-1. Status The Status page displays basic system information about the access point. 25 Model Uptime Firmware Version Hardware Version Serial Number Boot Code Version Runtime Code Version LAN IP Address LAN Subnet Mask LAN Default Gateway LAN MAC address DNS #1 DNS #2 Displays the model number of the access point. Displays the total time since the device was turned on. Displays the firmware version. Displays the hardware version. Displays the operating mode. Displays the access points ESSID, also known as SSID. The ESSID/SSID is the name used to identify a wireless network. Displays the current wireless channel number. Displays the IP address of this device. Displays the subnet mask of the IP address. Displays the IP address of the default gateway. Displays the devices MAC address. The MAC address is a unique, fixed ID for this device, it cannot be modified. IP address of DNS (Domain Name Server) #1. IP address of DNS (Domain Name Server) #2. 26 IV-1-2. LAN Settings The LAN Settings page allows you to configure your Local Area Network (LAN). You can enable the access point to dynamically allocate IP addresses to your LAN clients, and you can modify the IP address of the access point. Bridge Type IP Address IP Subnet Mask Default Gateway IP Address DNS 802.1d Spanning Tree Specify the IP address here. This IP address will be assigned to your access point and will replace the default IP address. Specify a subnet mask. The default value is 255.255.255.0 Enter the default gateway assigned by your ISP here. Some ISPs may call this Default Route. Select Enable or Disable to enable/disable 802.1d Spanning Tree. This creates a tree of connected layer-2 bridges (typically Ethernet 27 switches) within a mesh network, and disables those links that are not part of the tree, leaving a single active path between any two network nodes. Enable or disable the DHCP server. Enter the start IP address for the DHCP servers IP address leases. Enter the end IP address for the DHCP servers IP address leases. Enter a domain name for your network. Select a lease time for the DHCP leases here. The DHCP client will obtain a new IP address after the period expires. If there are less than 30 computers connected to the router, you can select Forever. DHCP Server Start IP End IP Domain Name Lease Time 28 IV-1-3. System Log processes. The system log displays system operation information such as up time and connection 29 Save Clear Refresh Click Save and you will be prompted (example shown below) to save the log on your computer as .txt file. Click Clear to clear/erase the existing log. Click Refresh to refresh the log and update any activity. Wireless Setting IV-2. Screenshots displayed are examples. The information shown on your screen will vary depending on your configuration. IV-2-1. Status wireless networks. The Status page displays a summary of key information about your access points 2.4GHz Mode Channel SSID1 ESSID Security BSSID 30 Displays the wireless channel number used for the specified frequency (2.4GHz). Displays which SSID number the following ESSID, Security and BSSID fields refer to. Displays the ESSID (also referred to as SSID) for the access points specified wireless network. The ESSID/SSID is the name used to identify a wireless network Displays the wireless security/encryption type for the specified wireless network. Displays the devices BSSID. The BSSID identifies this access point in the network, and is the same as the devices MAC address. 31 IV-2-2. 2.4GHz The 2.4GHz menu allows you to access basic, advanced and security settings for your access points 2.4GHz wireless networks. You can also enable or disable the access points 2.4GHz wireless networks. Enable/Disable Enable or disable the access points 2.4GHz wireless network. IV-2-2-1. Basic The Basic screen displays settings for your access points 2.4GHz Wi-Fi network (s). 32 Mode Power Saving Mode Enable or disable power saving mode on the Band Enable SSID#
SSID1,2,3,4 Channel access point. Select the wireless standard used for the access point. Combinations of 802.11b, 802.11g & 802.11n can be selected. Select how many SSIDs to enable for the 2.4GHz frequency from the drop down menu. A maximum of four can be enabled. Enter the SSID name for the specified SSID (1, 2, 3 or 4 depending on how many you have enabled). The SSID can consist of any combination of up to 32 alphanumeric characters. Select a wireless radio channel or use the default Auto setting from the drop-down menu. 33 IV-2-2-2. Advanced These settings are for experienced users only. Please do not change any of the values on this page unless you are already familiar with these functions. Changing these settings can adversely affect the performance of your access point. Fragment Threshold RTS Threshold Beacon Interval DTIM Period Data Rate N Data Rate Set the fragment threshold of the wireless radio. The default value is 2346. Set the RTS threshold of the wireless radio. The default value is 2347. Set the beacon interval of the wireless radio. The default value is 100. Set the DTIM (delivery traffic indication message) period value of the wireless radio. The default value is 1. Set the wireless data rate. The default is set to auto. Set the 802.11n wireless data rate. The default is set to auto. 34 Channel Bandwidth Select wireless channel width (analogue signal bandwidth used by wireless signals from the device) from Auto 20/40Mhz or 20Mhz the recommended value is Auto 20/40MHz. Set the wireless radio preamble type. The default value is Short Preamble. Enabling this setting will reduce the chance of radio signal collisions between 802.11b and 802.11g wireless access points. Its recommended to set this option to Auto. Set the power output of the wireless radio. You may not require 100% output power. Setting a lower power output can enhance security since potentially malicious/unknown users in distant areas will not be able to access your signal. Preamble Type CTS Protection Tx Power 35 IV-2-2-3. Security The access point provides various security options (wireless data encryption). When data is encrypted, information transmitted wirelessly cannot be read by anyone who does not know the correct encryption key. Its essential to configure wireless security in order to prevent unauthorised access to your network. WPA Pre-shared Key is the recommended security type. Select hard-to-guess passwords which include combinations of numbers, letters and symbols, and change your password regularly. 36 SSID Selection Broadcast ESSID WMM Encryption Select which SSID to configure security settings for. Enable or disable ESSID broadcast. When enabled, the ESSID will be visible to clients as an available Wi-Fi network. When disabled, the ESSID will not be visible as an available Wi-Fi network to clients clients must manually enter the ESSID in order to connect. A hidden
(disabled) ESSID is typically more secure than a visible (enabled) SSID. Enable or disable WMM. WMM (Wi-Fi Multimedia) technology can improve the performance of certain network applications, such as audio/video streaming, network telephony (VoIP) and others. When WMM is enabled, the device will prioritize different kinds of data and give higher priority to applications which require instant responses for better performance. Select an encryption type from the drop-down menu and refer to the following chapters for more information. The recommended encryption type is WPA Pre-shared Key. 37 IV-2-2-3-1. Disable Encryption is disabled and no password/key is required to connect to the BR-6428nS V2/nC. Disabling wireless encryption is not recommended. When disabled, anybody within range can connect to your devices SSID. IV-2-2-3-2. WEP WEP (Wired Equivalent Privacy) is a basic encryption type. For a higher level of security consider using WPA encryption. Authentication Type Key Length Key Type Default Key Encryption Key 1 4 Select Open System, Shared Key or Auto authentication type. Select 64-bit or 128-bit. 128-bit is more secure than 64-bit and is recommended. Choose from ASCII (any alphanumerical character 0-9, a-z and A-Z) or Hex (any characters from 0-9, a-f and A-F). Select which encryption key (1 4 below) is the default key. For security purposes, you can set up to four keys (below) and change which is the default key. Enter your encryption key/password according to the format you selected above. 38 IV-2-2-3-3. WPA Pre-shared Key WPA Pre-shared key is the recommended and most secure encryption type. WPA Type Pre-shared Key Format Pre-shared Key Select from WPA (TKIP), WPA2 (AES) or WPA2 Mixed. WPA2 (AES) is safer than WPA (TKIP), but not supported by all wireless clients. Please make sure your wireless client supports your selection. WPA2 (AES) is recommended followed by WPA2 Mixed if your client does not support WPA2 (AES). Choose from Passphrase (8 63 alphanumeric characters) or Hex (up to 64 characters from 0-9, a-f and A-F). Please enter a security key/password according to the format you selected above. IV-2-2-3-4. WPA RADIUS WPA RADIUS is a combination of WPA encryption and RADIUS user authentication. If you have a RADIUS authentication server, you can authenticate the identity of every wireless client against a user database. WPA Type Select from WPA (TKIP), WPA2 (AES) or WPA2 Mixed. WPA2 (AES) is safer than WPA (TKIP), but not supported by all wireless clients. Please make sure your wireless client supports your selection. WPA2 (AES) is recommended followed by WPA2 Mixed if your client does not support WPA2 (AES). Enter the IP address of the RADIUS authentication server here. RADIUS Server IP address RADIUS Server Port Enter the port number of the RADIUS RADIUS Server Password 39 authentication server here. The default value is 1812. Enter the password of the RADIUS authentication server here. IV-2-2-3-5. 802.1x (WEP) Enable 802.1x Authentication RADIUS Server IP Address RADIUS Server Port RADIUS Server Password Enable or disable the use of 802.1x user authentication. Enter the IP address of the RADIUS authentication server here. Enter the port number of the RADIUS authentication server here. Default value is 1812. Enter the password of the RADIUS authentication server here. 40 IV-2-3. MAC Filter Mac filtering is a security feature that can help to prevent unauthorized users from connecting to your access point. This function allows you to define a list of network devices permitted to connect to the BR-6428nS V2/nC. Devices are each identified by their unique MAC address. If a device which is not on the list of permitted MAC addresses attempts to connect to the BR-6428nS V2/nC, it will be denied. To enable this function, check the box labeled Enable Wireless Access Control. MAC address Comment Add Reset 41 Enter a MAC address of computer or network device manually without dashes or colons e.g. for MAC address aa-bb-cc-dd-ee-ff enter aabbccddeeff. Enter a comment for reference/identification consisting of up to 16 alphanumerical characters. Click Add to add the MAC address to the MAC address filtering table. Clear all fields. MAC address entries will be listed in the MAC Address Filtering Table. Select an entry using the Select checkbox. Delete selected or all entries from the table. Delete Selected/
Delete All IV-2-4. WPS Wi-Fi Protected Setup is a simple way to establish connections between WPS compatible devices. WPS can be activated on compatible devices by pushing a WPS button on the device or from within the devices firmware/configuration interface. When WPS is activated in the correct manner and at the correct time for two compatible devices, they will automatically connect. PIN code WPS includes the use of a PIN code between the two devices for verification. 42 Enable WPS Check/uncheck this box to enable/disable WPS. WPS Current Status Displays Configured or unConfigured depending on whether WPS and security/encryption settings for the device have been configured or not, either manually or using the WPS button. Displays the WPS PIN code of the device. Self PIN Code 2.4 GHz SSID Displays the SSID (ESSID) of the device. 2.4GHz Authentication Mode 2.4GHz Passphrase Key Configure via Push Button WPS via PIN Displays the wireless security authentication mode of the device. Displays the wireless security authentication key type. Click Start to Process to activate WPS on the access point. WPS will be active for 2 minutes. Enter the wireless clients PIN code here and click Start to Process to activate PIN code WPS. Refer to your wireless clients documentation if you are unsure of its PIN code. 43 IV-2-5. Client List point. The Client List page displays a table of all clients which are connected to the access Interface MAC Address Refresh Interface of each client (2.4GHz) is displayed here. The MAC address each client connected to the access point is displayed here. Click to refresh the list of connected clients. 44 IV-3. Toolbox Screenshots displayed are examples. The information shown on your screen will vary depending on your configuration. IV-3-1. Admin You can change the password used to login to the browser-based configuration interface here. It is advised to do so for security purposes. If you change the administrator password, please make a note of the new password. In the event that you forget this password and are unable to login to the browser based configuration interface, see II-2. Reset for how to reset the access point. Current Password Enter your current password. The default New Password Re-Enter Password password is 1234. Enter your desired new password here. You can use any combination of letters, numbers and symbols up to 20 characters. Confirm your new password. 45 IV-3-2. Time Setting You can configure the time zone settings of your access point here. The date and time of the device can be configured manually or can be synchronized with a time server. Time Zone Time Server Address Select the time zone of your country/ region. If your country/region is not listed, please select another country/region whose time zone is the same as yours. The access point also supports NTP (Network Time Protocol) for automatic time and date setup. Enter the host name or IP address of the time server if you wish. 46 IV-3-3. Diagnosis The diagnosis tool can ping a specific IP address and display the result in the box below. A ping is a test packet of information sent to determine the reachability of a host on an IP network, and to measure the round-trip time for messages sent from the originating host to a destination computer. Ping Address Ping Specify the host name or IP address to ping. Click Ping to begin. 47 IV-3-4. Firmware The Firmware page allows you to update the system firmware to a more recent version. Updated firmware versions often offer increased performance and security, as well as bug fixes. You can download the latest firmware from the Edimax website. Do not switch off or disconnect the access point during a firmware upgrade, as this could damage the device. Browse Open a new window to locate and select the firmware file in your computer. 48 IV-3-5. System Setting The access points System Setting page enables you to restore the device back to factory default settings, back up the current settings, or restore the device to previously saved settings. Restore to Factory Defaults Backup Settings Restore Settings Click Reset to restore settings to the factory default. A pop-up window will appear and ask you to confirm and enter your log in details. Enter your username and password and click Ok. See below for more information. Click Save to save the current settings on your computer as config.bin file. Click the browse button to find a previously saved config.bin file and then click Upload to replace your current settings. 49 IV-3-6. Reboot If the access point malfunctions or is not responding, then it is recommended that you reboot the device. You can reboot the access point remotely using this feature if the location of the access point is not convenient. Apply Click Apply to reboot the device. A countdown will indicate the progress of the reboot. 50 III. Appendix Configuring your IP address IV-1. The access point uses the default IP address 192.168.2.2. In order to access the browser based configuration interface, you need to modify the IP address of your computer to be in the same IP address subnet e.g. 192.168.2.x (x = 3 254). The procedure for modifying your IP address varies across different operating systems; please follow the guide appropriate for your operating system. In the following examples we use the IP address 192.168.2.10 though you can use any IP address in the range 192.168.2.x (x = 3 254). 51 Windows XP IV-1-2-1. 1. Click the Start button (it should be located in the lower-left corner of your computer), then click Control Panel. Double-click the Network and Internet Connections icon, click Network Connections, and then double-click Local Area Connection. The Local Area Connection Status window will then appear, click Properties. 2. Select Use the following IP address, then input the following values:
IP address: 192.168.2.10 Subnet Mask: 255.255.255.0 Click OK when finished. 52 53 Windows Vista IV-1-2-2. 1. Click the Start button (it should be located in the lower-left corner of your computer), then click Control Panel. Click View Network Status and Tasks, then click Manage Network Connections. Right-click Local Area Network, then select Properties. The Local Area Connection Properties window will then appear, select Internet Protocol Version 4 (TCP / IPv4), and then click Properties. 2. Select Use the following IP address, then input the following values:
IP address: 192.168.2.10 Subnet Mask: 255.255.255.0 Click OK when finished. 54 55 Windows 7 IV-1-2-3. 1. Click the Start button (it should be located in the lower-left corner of your computer), then click Control Panel. 2. Under Network and Internet click View network status and tasks. 3. Click Local Area Connection. 56 4. Click Properties. 57 5. Select Internet Protocol Version 4 (TCP/IPv4) and then click Properties. 6. Select Use the following IP address, then input the following values:
IP address: 192.168.2.10 Subnet Mask: 255.255.255.0 Click OK when finished. 58 59 Windows 8 IV-1-2-4. 1. From the Windows 8 Start screen, you need to switch to desktop mode. Move your curser to the bottom left of the screen and click. 2. In desktop mode, click the File Explorer icon in the bottom left of the screen, as shown below. 60 3. Right click Network and then select Properties. 4. In the window that opens, select Change adapter settings from the left 61 side. 5. Choose your connection and right click, then select Properties. 62 6. Select Internet Protocol Version 4 (TCP/IPv4) and then click Properties. 7. Select Use the following IP address, then input the following values:
IP address: 192.168.2.10 Subnet Mask: 255.255.255.0 Click OK when finished. 63 Mac IV-1-2-5. 1. Have your Macintosh computer operate as usual, and click on System Preferences 2. In System Preferences, click on Network. 3. Click on Ethernet in the left panel. 4. Open the drop-down menu labeled Configure IPv4 and select Manually. 64 5. Enter the IP address 192.168.2.10 and subnet mask 255.255.255.0. Click on Apply to save the changes. 65 IV-1-5. Glossary Default Gateway (Access point): Every non-access point IP device needs to configure a default gateways IP address. When the device sends out an IP packet, if the destination is not on the same network, the device has to send the packet to its default gateway, which will then send it out towards the destination. DHCP: Dynamic Host Configuration Protocol. This protocol automatically gives every computer on your home network an IP address. DNS Server IP Address: DNS stands for Domain Name System, which allows Internet servers to have a domain name (such as www.Broadbandaccess point.com) and one or more IP addresses (such as 192.34.45.8). A DNS server keeps a database of Internet servers and their respective domain names and IP addresses, so that when a domain name is requested (as in typing
"Broadbandaccess point.com" into your Internet browser), the user is sent to the proper IP address. The DNS server IP address used by the computers on your home network is the location of the DNS server your ISP has assigned to you. DSL Modem: DSL stands for Digital Subscriber Line. A DSL modem uses your existing phone lines to transmit data at high speeds. Ethernet: A standard for computer networks. Ethernet networks are connected by special cables and hubs, and move data around at up to 10/100 million bits per second (Mbps). IP Address and Network (Subnet) Mask: IP stands for Internet Protocol. An IP address consists of a series of four numbers separated by periods, that identifies a single, unique Internet computer host in an IP network. Example:
192.168.2.1. It consists of 2 portions: the IP network address, and the host identifier. The IP address is a 32-bit binary pattern, which can be represented as four cascaded decimal numbers separated by .: aaa.aaa.aaa.aaa, where each aaa can be anything from 000 to 255, or as four cascaded binary numbers separated by .: bbbbbbbb.bbbbbbbb.bbbbbbbb.bbbbbbbb, where each b can either be 0 or 1. 66 A network mask is also a 32-bit binary pattern, and consists of consecutive leading 1s followed by consecutive trailing 0s, such as 11111111.11111111.11111111.00000000. Therefore sometimes a network mask can also be described simply as x number of leading 1s. When both are represented side by side in their binary forms, all bits in the IP address that correspond to 1s in the network mask become part of the IP network address, and the remaining bits correspond to the host ID. For example, if the IP address for a device is, in its binary form, 11011001.10110000.10010000.00000111, and if its network mask is, 11111111.11111111.11110000.00000000 It means the devices network address is 11011001.10110000.10010000.00000000, and its host ID is, 00000000.00000000.00000000.00000111. This is a convenient and efficient method for access points to route IP packets to their destination. ISP Gateway Address: (see ISP for definition). The ISP Gateway Address is an IP address for the Internet access point located at the ISP's office. ISP: Internet Service Provider. An ISP is a business that provides connectivity to the Internet for individuals and other businesses or organizations. LAN: Local Area Network. A LAN is a group of computers and devices connected together in a relatively small area (such as a house or an office). Your home network is considered a LAN. MAC Address: MAC stands for Media Access Control. A MAC address is the hardware address of a device connected to a network. The MAC address is a unique identifier for a device with an Ethernet interface. It is comprised of two parts: 3 bytes of data that corresponds to the Manufacturer ID (unique for each manufacturer), plus 3 bytes that are often used as the products serial number. NAT: Network Address Translation. This process allows all of the computers on your home network to use one IP address. Using the broadband access points NAT capability, you can access the Internet from any computer on your home network without having to purchase more IP addresses from your ISP. Port: Network Clients (LAN PC) uses port numbers to distinguish one network application/protocol over another. Below is a list of common applications and protocol/port numbers:
67 23 21 25 110 1720 161 162 80 1723 5631 5632 Application Protocol Port Number TCP Telnet TCP FTP TCP SMTP TCP POP3 TCP H.323 SNMP UCP SNMP Trap UDP HTTP TCP PPTP TCP PC Anywhere TCP PC Anywhere UDP Access point: A access point is an intelligent network device that forwards packets between different networks based on network layer address information such as IP addresses. Subnet Mask: A subnet mask, which may be a part of the TCP/IP information provided by your ISP, is a set of four numbers (e.g. 255.255.255.0) configured like an IP address. It is used to create IP address numbers used only within a particular network (as opposed to valid IP address numbers recognized by the Internet, which must be assigned by InterNIC). TCP/IP, UDP: Transmission Control Protocol/Internet Protocol (TCP/IP) and Unreliable Datagram Protocol (UDP). TCP/IP is the standard protocol for data transmission over the Internet. Both TCP and UDP are transport layer protocol. TCP performs proper error detection and error recovery, and thus is reliable. UDP on the other hand is not reliable. They both run on top of the IP (Internet Protocol), a network layer protocol. WAN: Wide Area Network. A network that connects computers located in geographically separate areas (e.g. different buildings, cities, countries). The Internet is a wide area network. Web-based management Graphical User Interface (GUI): Many devices support a graphical user interface that is based on the web browser. This means the user can use the familiar Netscape or Microsoft Internet Explorer to Control/configure or monitor the device being managed. 68 COPYRIGHT Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd. makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability, or fitness for any particular purpose. Any software described in this manual is sold or licensed as is. Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Edimax Technology Co., Ltd. reserves the right to revise this publication and to make changes from time to time in the contents hereof without the obligation to notify any person of such revision or changes. The product you have purchased and the setup screen may appear slightly different from those shown in this QIG. The software and specifications are subject to change without notice. Please visit our website www.edimax.com for updates. All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders. 69 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio technician for help. FCC Caution This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment. Federal Communications Commission (FCC) Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 2.5cm (1 inch) during normal operation. Federal Communications Commission (FCC) RF Exposure Requirements SAR compliance has been established in the laptop computer(s) configurations with PCMCIA slot on the side near the center, as tested in the application for certification, and can be used in laptop computer(s) with substantially similar physical dimensions, construction, and electrical and RF characteristics. Use in other devices such as PDAs or lap pads is not authorized. This transmitter is restricted for use with the specific antenna tested in the application for certification. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC
(Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000. Safety This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment. EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria, Belgium, Bulgaria, Cyprus, Czech, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Turkey, and United Kingdom. The ETSI version of this device is also authorized for use in EFTA member states: Iceland, Liechtenstein, Norway, and Switzerland. EU Countries Not Intended for Use None 70 EU Declaration of Conformity English:
Franais:
etina:
Polski:
This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC. Cet quipement est conforme aux exigences essentielles et autres dispositions de la directive 1999/5/CE, 2009/125/CE, 2006/95/CE, 2011/65/CE. Toto zazen je v souladu se zkladnmi poadavky a ostatnmi pslunmi ustanovenmi smrnic 1999/5/ES, 2009/125/ES, 2006/95/ES, 2011/65/ES. Urzdzenie jest zgodne z oglnymi wymaganiami oraz szczeglnymi warunkami okrelonymi Dyrektyw UE 1999/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC.. Romn: Acest echipament este n conformitate cu cerinele eseniale i alte prevederi relevante ale
:
Magyar:
Trke:
Directivei 1999/5/CE, 2009/125/CE, 2006/95/CE, 2011/65/CE. 1999/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC. Ez a berendezs megfelel az alapvet kvetelmnyeknek s ms vonatkoz irnyelveknek
(1999/5/EK, 2009/125/EK, 2006/95/EK, 2011/65/EK). Bu cihaz 1999/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC direktifleri zorunlu istekler ve dier hkmlerle ile uyumludur.
: 1999/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC.. Slovenina: Toto zariadenie spa zkladn poiadavky a alie prslun ustanovenia smernc Deutsch:
Espaol:
1999/5/ES, 2009/125/ES, 2006/95/ES, 2011/65/ES. Dieses Gert erfllt die Voraussetzungen gem den Richtlinien 1999/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC. El presente equipo cumple los requisitos esenciales de la Directiva 1999/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC. Italiano: Questo apparecchio conforme ai requisiti essenziali e alle altre disposizioni applicabili della Direttiva 1999/5/CE, 2009/125/CE, 2006/95/CE, 2011/65/CE. Nederlands: Dit apparaat voldoet aan de essentile eisen en andere van toepassing zijnde bepalingen van richtlijn 1999/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC.. Portugus: Este equipamento cumpre os requesitos essnciais da Directiva 1999/5/EC, 2009/125/EC, Norsk:
2006/95/EC, 2011/65/EC. Dette utstyret er i samsvar med de viktigste kravene og andre relevante regler i Direktiv 1999/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC. Svenska: Denna utrustning r i verensstmmelse med de vsentliga kraven och vriga relevanta Dansk:
bestmmelser i direktiv 1999/5/EG, 2009/125/EG, 2006/95/EG, 2011/65/EG. Dette udstyr er i overensstemmelse med de v sentligste krav og andre relevante forordninger i direktiv 1999/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC. suomen kieli: Tm laite tytt direktiivien 1999/5/EY, 2009/125/EY, 2006/95/EY, 2011/65/EY oleelliset vaatimukset ja muut asiaankuuluvat mrykset.
-----------------------------------------------------------------------------------------------------------------------
WEEE Directive & Product Disposal 71 At the end of its serviceable life, this product should not be treated as household or general waste. It should be handed over to the applicable collection point for the recycling of electrical and electronic equipment, or returned to the supplier for disposal. Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European R&TTE directive 1999/5/EC, and 2009/125/EC, 2006/95/EC, 2011/65/EC . Equipment: N300 Wall-plug Access Point Model No.:
EW-7438APn The following European standards for essential requirements have been followed:
Spectrum:
EMC:
ETSI EN 300 328 V1.7.1 (2006-10) EN 301 489-1 V1.9.2 (2011-09);
EN 301 489-17 V2.1.1 (2009-05) EMF: EN 50385:2002 Safety (LVD):
IEC 60950-1:2005 (2nd Edition);
EN-60950-1:2006+A11:2009+A1:2010+A12:2011 Edimax Technology Co., Ltd. No. 3, Wu Chuan 3rd Road, Wu-Ku Industrial Park, New Taipei City, Taiwan Date of Signature: November 15, 2011 Signature:
Printed Name:
Title:
Albert Chang Director Edimax Technology Co., Ltd. 72 Notice According to GNU General Public License Version 2 This product includes software that is subject to the GNU General Public License version 2. The program is free software and distributed without any warranty of the author. We offer, valid for at least three years, to give you, for a charge no more than the costs of physically performing source distribution, a complete machine-readable copy of the corresponding source code. Das Produkt beinhaltet Software, die den Bedingungen der GNU/GPL-Version 2 unterliegt. Das Programm ist eine sog. Free Software, der Autor stellt das Programm ohne irgendeine Gewhrleistungen zur Verfgung. Wir bieten Ihnen fr einen Zeitraum von drei Jahren an, eine vollstndige maschinenlesbare Kopie des Quelltextes der Programme zur Verfgung zu stellen zu nicht hheren Kosten als denen, die durch den physikalischen Kopiervorgang anfallen. GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundations software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public License instead.) You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things. To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it. For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software. Also, for each authors protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors reputations. Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyones free use or not licensed at all. The precise terms and conditions for copying, distribution and modification follow. TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The Program, below, refers to any such program or work, and a work based on the Program means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language.
(Hereinafter, translation is included without limitation in the term modification.) Each licensee is addressed as you. Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does. 73 1. You may copy and distribute verbatim copies of the Programs source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:
a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change. c) b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License. If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program. In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.) The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. 4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 74 5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License. 7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and any later version, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation. 10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. 75
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2015-01-12 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2015-01-12
|
||||
1 | Applicant's complete, legal business name |
Edimax Technology Co Ltd
|
||||
1 | FCC Registration Number (FRN) |
0008842908
|
||||
1 | Physical Address |
No.278, Xinhu 1st Rd., Neihu Dist.
|
||||
1 |
Taipei City, N/A
|
|||||
1 |
Taiwan
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
B******@phoenix-testlab.de
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
NDD
|
||||
1 | Equipment Product Code |
9574761414
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
T****** C******
|
||||
1 | Title |
senior Specialist
|
||||
1 | Telephone Number |
+886-********
|
||||
1 | Fax Number |
+886-********
|
||||
1 |
t******@edimax.com.tw
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DTS - Digital Transmission System | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | N300 Ceiling-Mount Access Point | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Output Power listed is peak conducted. This device has 20 and 40 MHz BW modes. This device must be installed and operated to provide a separation distance of at least 20 cm from all. Endusers must be provided with the transmitter operating conditions for satisfying RF exposure compliance. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Sporton International Inc.
|
||||
1 | Name |
A**** C******
|
||||
1 | Telephone Number |
886-3******** Extension:
|
||||
1 | Fax Number |
886-3********
|
||||
1 |
a******@sporton.com.tw
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2412.00000000 | 2462.00000000 | 0.9980000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC