VHF Air BAnd TrAnsceiVer FL-M1000A/FL-M1000e instruction Manual ATTenTiOn reAd Me FirsT Fcc WArninG Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. nOTice:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Properly shielded a grounded cables and connectors must be used for connection to host computer and /
or peripherals in order to meet FCC emission limits. (AC adaptor) with ferrite core must be used for RF interference suppression. notes to the installer /
User. This is a 13.8-volt or 26.4-volt DC radio, voltages greater than 33 volts DC or AC voltage will severely damage it. When making adjustments to the transmitter, ensure that you are not on an occupied channel. Do not transmit on 121.500MHz, as this is the international distress frequency. Do not transmit into an unterminated antenna line as a suitable antenna must be connected. Transmitting without being connected to an antenna may damage the radio. Ensure that the supply voltage is regulated and does not fall below 11.7 volts DC or exceed 31 volts DC. The transceiver is not waterproof. Do not allow it to get wet. Speaker impedance must be either 4 or 8 ohms (4 ohms preferred) at 10 watts. Use of electret microphones highly recommended. About this document. Due to our policy of continuous improvement to our products and services, technical specifications and claims are correct at time of going to printing, however they are subject to change without notice. Flightline does not accept liability for any error or omission. This manual remains the copyright of Flightline.
cOnTenTs inTrOdUcTiOn ......................................4 Introduction ...............................................4 Part names and functions ........................5 MP-1000 microphone ...............................7 Display ......................................................8 Recalling the Pri channel ........................10 BAsic OperATiOn ..............................11 Basic usage ............................................11 Turning the power on or off ....................12 Adjusting the audio volume ....................12 Adjusting the squelch level .....................13 Changing the channel .............................14 Change mHz/kHz for variable frequency .............................................14 Dimmer ....................................................15 Transmitting ............................................15 MeMOry And scAn OperATiOn .....16 Scanning the VFO frequencies ...............16 Scanning the memory.............................16 Scanning with the priority channel .........17 Priority watch ..........................................18 Other memory operations ......................19 MeMOry OperATiOns ...................... 20 Memorizing a frequency .........................20 Switching the VFO and memory mode .....................................20 Erasing a memory ...................................21 Setting the priority memory ....................21 Recalling the priority channel ................ 22 Naming the memory channel
(Memory tag) .......................................23 Setting the lockout memory channel .....24 AdVAnced OperATiOn..................... 25 Emergency call .......................................25 Changing the settings .............................25 Changing the each settings ....................26 Appendix ............................................. 27 Connecting ..............................................27 Mounting ................................................ 29 Optional headset adapter ...................... 30 Specifications ........................................ 32 Frequency list (Example of frequency versus display when using 8.33 Khz step) .................................................... 33 Supplied accessories ............................ 34
inTrOdUcTiOn introduction Thank you for purchasing this quality product from Flightline. This transceiver has been designed and manufactured in Japan. This is the best product for vehicle working in the Airport. Ease of operation was another primary achievement. Please follow this manual closely to ensure optimum performance, we do hope you have many hours of trouble free communication. installation instructions This manual contains all of the necessary instructions for installation and operation. After installation please keep this manual in a safe place for future reference.
installation considerations As with all air Air Band radios, successful communications start with the installation. After unpacking the transceiver verify all parts against the parts list. The Display provides a 30-degrees field of view from right and left, and from upper side. However from the down side, it is out of guarantee. Please be careful when install this product. The use of aviation quality shielded cable is recommended at all times. Avoid running or wrapping other wires around the antenna lead and keep lengths as short as reasonably possible. Ensure that the radio is not exposed to direct rain or moisture (we do not accept liability for water damage). Make sure the transceiver is connected to a 11.7-16.8 volt or 23-31 volt battery system. Do not use AC volts from a Rotax lighting coil. About this product This product is Air Band Land Mobile Radio designed for vehicle, not for Aircraft. The radio can be operated with Hand Microphone or Headset. You can choose audio output from External Speaker and/
or Headphone. The radio has various built-in Scan function. inTrOdUcTiOn part names and Functions Front panel
kHz
V/M SCAN PRI SQL PWR FL-M1000
q Tx/rx indicator Indicate Red in transmission, Green in t pWr button Short press: indicates voltage of power Receiving. w rotary encoder Change the operating Frequency or Memory Channel. Turning this Encoder while pausing scan resumes the Scan mode. LCD Backlight will be ON by short press. Available to change the tuning range by Long Press. e Volume button The audio volume will be up or down. r internal speaker Internal Speaker. The audio output is available to change to Headphone. source. Long press: turn the radio ON/OFF. y sQL button Available to change the Squelch setting. u pri button Short Press: recall the Priority Channel. Long Press: recall the Emergency Channel.. i scAn button Short Press: start SCAN function. Long Press: start Dual Watch function. o V/M button Short Press: switch between Memory mode and VFO mode. Long Press: Add memory current channel.
inTrOdUcTiOn
!0 Microphone connecter Connect the supplied Microphone
(do not connect other microphone to prevent trouble)
inTrOdUcTiOn Mp-1000 Microphone
q Volume Up/dOWn Decrease audio volume by press the v button, and increase by c button w Monitor Button Press the button makes the radio in monitor mode. e pTT (push To Talk) Press the button makes the radio to transmit mode, and release to receive mode. r Microphone Speak into the circled area when talking. note:
There is a microphone element in the circled area. The sound becomes unclear if it doesnt speak toward the circled part. t Busy indicator (Green) It will become Green while somebody is talking, or squelch is open. y Hanger It is a metal hanger to hook the microphone.
inTrOdUcTiOn display
q Low battery indicator The L will indicate when the voltage of power source becomes less than 11.7 Volt. w Busy indicator The Busy icon will indicate when receiving. e emergency indicator The EMG icon will indicate when recall the Emergency channel. r priority Watch indicator The P icon will indicate when the radio is in Priority Scan or Priority watch mode. t scan indicator The SCAN icon will indicate when the radio is in SCAN mode.
y Memory indicator The MR icon will indicate when the radio is displaying a memory channel. u LOcKOUT indicator The LOCKOUT icon will indicate when the channel is not in the SCAN LIST. i setting mode indicator The SET icon will indicate when the radio is in SETTING mode. o Volume level indicator It indicates the Audio Volume Level.
!0 Memory number indicator It shows memory number or Pr as priority.
!1 Main indicator It shows frequency and/or setting etc..
!2 decimal point indicator It indicates dot at decimal point. inTrOdUcTiOn rear panel
q Antenna connector Connect an Antenna with PL-259 type
(50 ohms, SWR: less than 3.0) w power cable Connect a Battery (12 V or 24 V). Do not connect the other type. e external speaker Jack Connect a Speaker with more than 10 W, 8 ohms. r Optional Jack Connect a Headset (supplied by 3rd party) Please contact your dealer if you have any question.
inTrOdUcTiOn recalling the pri channel You can recall a Priority Channel by pressing the PRI button when the radio is in VFO mode or in Memory Channel mode. 1 press the pri button The channel will be changed to Priority Channel and the Pr will be displayed instead of memory channel number. 2 press the pri button again to return to previous channel 10 6 Turn the rotary Knob to select desired frequency. The TX/RX Indicator will become Green if the radio receives a signal. 7 Wait a signal from transmitting your partner. 8 Monitor the frequency is not busy before transmission. 9 Hold the microphone about 1 to 3cm away from your mouth. 10 speak slowly and clearly into the microphone with press and hold the pTT switch. The TX/RX Indicator on the radio will become Red while transmitting. BAsic OperATiOn Basic Usage 1 press the pWr button more than two seconds. 2 Adjust the audio level by Volume button. 3 press the sQL button to adjust the squelch level. 4 Turn the rotary Knob slowly direction to clockwise until noise disappear. 5 press the sQL button to save and exit the adjustment. 11 BAsic OperATiOn Turning the power On or Off Adjusting the Audio Volume 1 press and hold the pWr button more than two seconds to turn the radio On. The LCD will be activated and Frequency will be displayed on the LCD. 1 press the c button to increase audio level. 2 press and hold the pWr button more than two seconds to turn the radio OFF. 2 press the v button to decrease audio level. note:
The audio level will be continuously changed by Press and hold the buttons. 1
BAsic OperATiOn Adjusting the squelch Level 1 press the sQL button The Display will change to Squelch Setting mode. note:
The audio will be muted when receiving week signal if the SQL level is set too big. You can change Audio level while in Squelch Setting mode. 2 Turn the rotary Knob slowly direction to clockwise. 3 stop turning the Knob when noise disappears. 4 press the sQL button to save and exit the squelch adjustment. The Display will return to previous state. 1
BAsic OperATiOn changing the channel Frequency on the LCD will be changed by turning the Rotary Knob in VFO mode. Channel Number on the LCD will be changed by turning the Rotary Knob in Memory mode. 1 confirm the VFO mode before changing Frequency. There is no MR icon in VFO mode. 2 Turn the rotary Knob to change desired frequency. change MHz/kHz for Variable Frequency You can switch between MHz and kHz for changing frequencies in VFO mode. 1 confirm the radio is in VFO mode. 2 press and hold the rotary Knob more than one second. The variable part will be flashing. 3 press the V/M button to switch between VFO mode and Memory mode. There is MR icon in Memory mode. 4 Turn the rotary Knob to change desired Memory number. See page 20 how to memorize a frequency. 1
BAsic OperATiOn dimmer Transmitting The brightness of LCD Backlight can be changed. 1 confirm the radio is switched On. 2 short press the rotary Knob. The brightness will be changed as follows. Normal Dark OFF 1 confirm that the channel is not busy before transmitting. 2 Keep away your mouth from the microphone about one inch. 3 press and hold the pTT switch. 4 speak slowly and clearly into the microphone. The RX/TX Indicator on the radio will become Red. note:
There is a function Timeout Timer in this radio. The continuous transmitting will be automatically stopped for 3 minutes as default. The Timeout Timer can be selected from Off, 1, 3 and 5 minutes. (see page 25 or 26) 1
MeMOry OperATiOn scanning the Memory This function is Scanning for memorized channels. Please refer page 20; how to memorize a frequency. 1 confirm the radio is in VFO mode. 2 press V/M key to change to Memory mode. 3 confirm the radio is not receiving on the current channel. 4 press the scAn button. 5 you can see the radio is scanning. Memory scan If the radio receives a signal during Scanning, the radio will pause the scanning on the channel. 6 press the scAn button to stop the scanning. There are various functions such as Frequency Scanning on VFO mode, Memory Scanning on Memory mode or dual watch the specific two frequencies. scanning the VFO Frequencies It is Scanning for all available frequencies when the radio is in VFO mode. 1 confirm the radio is in VFO mode. 2 confirm the radio is not receiving on current channel. 3 press the scAn button. 4 The radio starts scanning. VFO Scan 118.00 MHz Skip
(25 kHz or 8.33 kHz step)*
The Frequency Step should be set by dealer 136.975 MHz If the radio receives a signal during Scan, the radio will pause the scanning on the channel. 5 press the scAn button to stop the scanning.
* Except USA Version. 1
MeMOry OperATiOn scanning with the priority channel The Priority Channel will be checked every 250 msec during the radio is in VFO scanning or Memory Scanning. 1 confirm the radio is in VFO mode or Memory mode. 2 confirm the radio is not receiving at the current channel. 3 press the scAn button. 4 confirm the radio starts the scanning. Priority Memory Scan 250 ms Pri Ch 250 ms 250 ms Skip Pri Ch 250 ms 250 ms Priority VFO Scan 118.00 MHz 250 ms Pri Ch 250 ms Skip 250 ms Pri Ch 250 ms 250 ms 136.975 MHz If the radio receives a signal during Scan, the radio will pause the scanning on the channel. The priority channel will be checked every 5 seconds even if the radio is receiving. The radio will pause the scanning if receiving a signal on the Priority Channel. 5 press the scAn button to stop the scanning. 1
MeMOry OperATiOn priority Watch 6 press the scAn button to stop the priority Watch. The Priority Watch is to watch the current channel (displayed frequency or memory channel) and Priority Channel alternately. 1 confirm the radio is in VFO mode or Memory mode. 2 select a desired frequency or memory channel to make the priority Watch. 3 confirm the radio is not receiving at displayed channel. 4 press and hold the scAn button until the p icon will appear on the Lcd. 5 confirm the radio starts the priority Watch. VFO or Memory 250 msec Pri Ch 250 ms VFO or Memory 250 msec Pri Ch 250 ms VFO or Memory 250 msec If the radio receives a signal during Scan, the radio will pause the scanning on the channel. The priority channel will be checked every 5 seconds even if the radio is receiving. The radio will pause the scanning if receiving a signal on the Priority Channel. 1
MeMOry OperATiOn Other Memory Operations There are advanced feature for Scanning, On hook scanning and Lock Out Memory. On hook scanning, Lock Out Memory On hook scanning The Scan will start when the microphone is ON Hook, and will stop when OFF Hook. In order to use this function, the Hook function must be enabled in the User Setting mode. Beside the microphone hook must be connected with ground level (Earth). If the microphone hook is not connected to Earth, the Hook function does not work. Lock Out Memory It is able to delete the channel from the Scan list to skip the channel during Scanning. 1
MeMOry OperATiOns switching the VFO and Memory Mode The operating mode can be changed between VFO mode and Memory mode. 1 press the V/M button. The operating mode will switch VFO mode and Memory mode every pressing the V/M button. This section shows how to memorize frequently using frequency as Memory Channel. Memorizing a Frequency 1 select a frequency that is going to memorize by rotary knob in the VFO mode. 2 press and hold the V/M button more than two seconds. The MR icon will appear and Memory Number will flash. 3 select desired number by rotary knob. The MR icon will not appear at the memory number that is not memorized a frequency. 4 press and hold the V/M button more than 2 seconds to save and exit. The display will return to VFO mode.
0 MeMOry OperATiOns erasing a Memory The memorized frequency can be erased. 1 press and hold the V/M button more than two seconds in VFO mode. The MR icon will appear and Memory Number will be flashing. 2 select a number that you want to erase by rotary knob. If frequency is memorized then MR icon will appear. 3 press and hold the sQL button more than two seconds. The displayed frequency will disappear. 4 press and hold the V/M button more than two seconds to save and exit. The display will return to previous VFO mode. If you want to exit without save the erase information, then short press the V/M button. setting the priority Memory Memorize a frequency that is most frequently using as Priority Channel. You can recall the Priority Channel easily by pressing the PRI button. The priority channel will be used for the Priority Scan or Priority Watch. 1 select a frequency that you want to make it as priority channel by rotary knob in VFO mode. 2 press and hold the V/M button more than two seconds. The MR icon will appear and Memory Number will be flashing. 3 press the pri button. The Memory Number will change to PR. 4 press and hold the V/M button more than two seconds. The Display will return to VFO mode.
1 MeMOry OperATiOns note:
It is available to memorize as priority channel if displaying the PR by turning the rotary knob at the step 3. recalling the priority channel The Priority Channel can be easily recalled by just pressing PRI button even when the radio is in VFO mode or Memory Channel mode. 1 press the pri button. The PR will appear instead of Memory Number. 2 press the pri button to return previous display.
MeMOry OperATiOns naming the Memory channel (Memory Tag) You can name the memory channel. The name will be displayed instead of frequency when you recall the memory channel if Memory Tag feature is enabled. 1 press the V/M button during the radio is in VFO mode. The MR icon and the Memory Number will be displayed. 2 select a Memory number that you want to make a name Tag by rotary knob. 3 press and hold the V/M button more than two seconds. The first digit will be flashing to input first character. 4 select a character by rotary knob. 5 press the c button to move second digit. 6 enter the name tag by repeating the step 4 and 5. It is available to enter maximum 6 characters. If pressing the v button then the entering digit will be backward. 7 press and hold the V/M button more than two seconds to save and exit. If you want to exit without save the tag information, then short press the V/M button. The radio will return to previous condition. note:
You can use following characters as the Name Tag;
0 to 9, A to Z, /, _, ., +, *, <, >, $, &
and Space To delete the Name Tag, select the named memory number then press and hold the SQL button more than two seconds.
MeMOry OperATiOns setting the Lockout Memory channel This section indicates how to delete
(lockout) a memory channel from the memory scan list. 1 press the V/M button during the radio is in VFO mode. The MR icon and the Memory Number will appear on the LCD. 2 select a Memory number that you want to skip for Memory scan by rotary knob. 3 press and hold the rotary Knob more than two second. The LOCKOUT icon will appear on the LCD. 4 press the V/M button to exit. The radio will return to previous VFO mode. note:
If you want to cancel the Lockout, then press and hold the rotary knob more than two seconds at the step 3. The LOCKOUT icon will disappear.
AdVAnced OperATiOn emergency call changing the settings It is easily recall an Emergency Channel
(121.5MHz) when the radio is in VFO mode, Memory mode and on the Priority Channel. 1 press and hold the pri button more than two seconds. The EMG icon and frequency 121.5MHz will be displayed on the LCD. The following functions can be changed;
Beep tone, External speaker setting, Internal speaker setting, Time out timer, Busy lockout, Memory tag, On hook 1 Turn the radio On with press and holding the V/M and sQL button. The SET icon with setting status will be displayed. Beep tone Busy lock Internal speaker On hook 2 press and hold the pri button to return previous display. Setting number Time out timer Extermal speaker Memory tag 2 select a desired function that you want to change by rotary knob. The selected item will be flashing. 3 press the rotary knob to change the value. 4 Turn the radio OFF after the changing completed.
AdVAnced OperATiOn changing the each settings The each setting can be changed individually. 1 Turn the radio On with press and holding the V/M and sQL buttons. The SET icon with setting status will be displayed. 2 select the setting number (and the number becomes flashing). 3 press the rotary knob. The individual setting will displayed. 4 press the rotary knob to get desired change. Beep tone Internal speaker setting Time out timer Busy lock out Memory tag On hook function 5 Turn the radio OFF after the changing completed. External speaker setting
Appendix Please contact your dealer about installation. connecting installing place The radio must not be installed in the place where driving is obstructed.
Appendix connections
q connect an Antenna and the Antenna connector The Antenna that has PL-259 type connector (50homs, SWR: less than 3) is available to connect. w connect power cable to Battery of the vehicle The available voltage of the Battery is 12V or 24V, do not connect the other type. e connect a speaker (3rd partys one) to external speaker Jack The available impedance of the speaker is 8 ohms, and the rated input power must be more than 10 W. r connect the Headset (supplied by 3rd party) to Optional Jack. t connecting the Microphone hanger to earth of the vehicle enables Microphone Hanger function.
Appendix Mounting The radio can settle on/under the dashboard using supplied bracket. The bracket must be fixed with supplied screws. Otherwise the bracket cannot be fixed tightly or inside of the radio may get serious damage.
Appendix Optional Headset Adapter When using an optional headset, such as those from the David Clark Co. via the adapter, the transceiver outputs your transmitted voice to the headset for monitoring. connection PTT switch Use a PTT switch with a 3.5 mm diameter plug, if required. HEADSET
(Must be purchased separately.)
0 Appendix installation The optional HEADSET ADAPTER install as follows. q Turns the power OFF, then disconnect the dc power cable. w Unscrew the 4 screws, then remove the bottom cover. e insert the connector as shown below. r Mount the phone plug attachment together with the mobile mounting bracket with 2 supplied screws.
1 Appendix specifications General Frequency range: .......................................118.000 to 136.975 MHz Channel spacing: .......................................*8.33 kHz / 25 kHz Mode: .........................................................AM (6K00A3E) Number of memory channels: ...................99 Acceptable power supply: .........................13.8 V or 26.4 VDC (Negative ground only) Usable temp. range: ..................................-30 C to +60 C Frequency stability: ...................................+/- 5 ppm Current drain: .............................................TX: 6 A (max), RX: 6 A (max), Standby: 260 mA Dimensions: ...............................................W 150 X D 190 X H 50 (mm) Weight: .......................................................1700 g Transmitter Output power: ............................................9 W (carrier) typical, 36 W (P-P) Modulation: ................................................Last stage modulation Modulation limiting: ...................................70 to 100%
Audio harmonics distortion: ......................Less than 15% (at 85% modulation) Hum and noise ratio: .................................More than 40 dB Spurious emissions: ..................................-16 dBm or less Antenna impedance: ..................................50 receiver Receive system: .........................................Double conversion superheterodyne Intermediate frequency: .............................1st : 38.85 MHz (Upper) 2nd : 450 kHz (Lower) Sensitivity (at 6dB S/N): ............................Less than 1uV Squelch sensitivity: ....................................0.5uV (Threshold) Selectivity 25 kHz channel spacing: .....................More than 8 kHz (at 6 dB)
*8.33 kHz channel spacing: .................More than 2.778 kHz (at 6 dB) Less than 7.37 kHz (at 60 dB) Less than 25 kHz (at 60 dB) Spurious response rejection: ....................More than 60 dB Audio output power: ..................................More than 15 W (at 4 ) Side tone: ...................................................More than 100 mW (at 600 ) Hum and noise: ..........................................More than 25 dB Audio output impedance: ..........................External. Speaker 4 (4 to 8 ) Side tone 600
* Except USA version
Appendix Frequency List (example of Frequency Versus display when Using 8.33 kHz step) Operating Frequency channel speacing (kHz) displayed Frequency 118.00000 118.00000 118.00833 118.01667 118.02500 118.02500 118.03333 118.04167 118.05000 118.05000 118.05833 118.06667 118.07500 118.07500 118.08333 118.09167 118.10000 118.10000 etc 25
*8.33
*8.33
*8.33 25
*8.33
*8.33
*8.33 25
*8.33
*8.33
*8.33 25
*8.33
*8.33
*8.33 25
*8.33 118.000 118.005 118.010 118.015 118.025 118.030 118.035 118.040 118.050 118.055 118.060 118.065 118.075 118.080 118.085 118.090 118.100 118.105 The display at 136.9750MHz (with 8.33 kHz step) will be 136.980.
* Except USA Version.
Appendix supplied Accessories
(1) MP1000 Microphone .......................................................................................... 1
(2) Microphone hanger and screw set ..................................................................... 1 set
(3) Microphone cable ............................................................................................... 1
(4) DC power cable (3 m(1 ft))with 10A Fuse .......................................................... 1
(5) Mounting bracket kit ........................................................................................... 1 Mounting bracket ................................................................................................ 1 Bracket bolt ......................................................................................................... 4 Mounting screw ................................................................................................. 4 Self-tapping screw ............................................................................................. 4 Flat washer .......................................................................................................... 4 Spring washer ..................................................................................................... 4 Nut ....................................................................................................................... 4
Limited liability warranty Flightline warrants this product to be free from defects in materials and workmanship for 1 year from the date of purchase or the minimum period described by applicable consumer law. If the unit is installed by an organization which holds an avionics installation approval from the FAA, and that organization has co-signed and dated the warranty card, the warranty period shall be deemed to commence from the date of installation. The customer shall be responsible for any transportation costs for return of this product to Flightline. This warranty does not cover failures due to abuse, misuse, accident, unauthorized alteration, or repairs carried out by parties other than Flightline or an approved Flightline service center. This warranty does not cover failures where the product has not been installed or operated, in accordance with the provisions of the User and Installation manual(s). It shall be at Flightline sole discretion to decide if a defect is a result of material or workmanship failure. T H e WA r r A n T i e s A n d r e M e d i e s c O n TA i n e d H e r e i n Are excLUsiVe And in LieU OF ALL OTHer WArrAnTies expressed Or iMpLied, incLUdinG Any LiABiLiTy ArisinG Under WArrAnTy OF MercHAnTABiLiTy Or FiTness FOr A pArTicULAr pUrpOse, sTATUAry Or OTHerWise. THis WArrAnTy GiVes yOU speciFic LeGAL riGHTs, WHicH MAy VAry FrOM sTATe TO sTATe, And cOUnTry TO cOUnTry. in nO eVenT sHALL FLiGHTLine Be LiABLe FOr Any incidenTAL, speciAL, indirecT Or cOnseQUenTiAL dAMAGes, WHeTHer resULTinG FrOM THe Use, MisUse Or inABiLiTy TO Use THis prOdUcT Or FrOM deFecTs in THe prOdUcT. Flightline may at it discretion, refer product returns for repair or service, to a service facility closest to you. Flightline reserves the right to repair or replace the unit or software or offer a full refund of the purchase price at its sole discretion. sUcH reMedy sHALL Be yOUr sOLe And excLUsiVe reMedy FOr Any BreAcH OF WArrAnTy. Supplied by Flightline 12830 E. Mirabeau Parkway Spokane Valley, WA 99216 Toll free tel.: 1-800-235-3300 Toll free fax: 1-800-828-0623 http://www.edmo.com Flightline 2009 All Rights Reserved Printed in Japan April 2009 00M70AC851010