all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Manual | Users Manual | 282.93 KiB | ||||
1 | External Photos | |||||||
1 | Cover Letter(s) | |||||||
1 | ID Label/Location Info | |||||||
1 | Cover Letter(s) | |||||||
1 | ID Label/Location Info | |||||||
1 | Internal Photos | |||||||
1 | Cover Letter(s) | April 03 2008 | ||||||
1 | Test Report | March 03 2008 | ||||||
1 | Test Report | March 03 2008 | ||||||
1 | Test Setup Photos |
1 | Manual | Users Manual | 282.93 KiB |
FLFLFLFL----760760760760 Aircraft Transceiver VHFVHFVHFVHF Aircraft Transceiver Aircraft Aircraft Transceiver Transceiver Installation / Operations Manual Installation / Operation s Manual Installation / Operation Installation / Operation s Manual s Manual FLFLFLFL----760 series 760 series 760 series 760 series Flightline Flightline Flightline Flightline 12830 E. Mirabeau Parkway 12830 E. Mirabeau Parkway 12830 E. Mirabeau Parkway 12830 E. Mirabeau Parkway Spokane Valley, WA 99216 Spokane Valley, WA 99216 Spokane Valley, WA 99216 Spokane Valley, WA 99216 tel.: 1: 1: 1: 1----800800800800----235235235235----3300 Toll free Toll free tel. 3300 33003300 Toll free Toll free tel. tel. Toll free fax: 1: 1: 1: 1----800800800800----828828828828----0623 Toll free fax 0623 Toll free fax Toll free fax 06230623 www.edmo.com http:// www.edmo.com http://
www.edmo.com www.edmo.com http://
http://
VHF AM Aircraft R VHF AM Aircraft Raaaadiodiodiodio VHF AM Aircraft R VHF AM Aircraft R FCC ID: VOSFL760 A FCC ID:
VOSFL760 A FCC ID:
FCC ID:
VOSFL760 A VOSFL760 A Page 0 AT T E N T I O N AT T E N T I O N AT T E N T I O N AT T E N T I O N READ ME FIRST READ ME FIRST READ ME FIRST READ ME FIRST FCC WARNING FCC WARNING FCC WARNING FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Properly shielded a grounded cables and connectors must be used for connection to host computer and /
or peripherals in order to meet FCC emission limits. AC adaptor with ferrite core must be used for RF interference suppression. The Flightline transceiver has been factory preset and in most cases the transmitted audio should The Flight line transceiver has been factory preset and in most cases the transmitted audio should line transceiver has been factory preset and in most cases the transmitted audio should The Flight The Flight line transceiver has been factory preset and in most cases the transmitted audio should be correct. A 15 pin connector is supplied for connection to the electrical sy be correct. A 15 pin connector is supplied for connection to the electrical system and stem and be correct. A 15 pin connector is supplied for connection to the electrical sy be correct. A 15 pin connector is supplied for connection to the electrical sy stem and stem and microphone/speaker. microphone/speaker. microphone/speaker. microphone/speaker. NotesNotesNotesNotes to the installer / user. to the installer / user. to the installer / user. to the installer / user. This is a 14-volt or 28-volt DC radio, voltages greater than 33 volts DC or AC voltage will severely damage it. When making adjustments to the transmitter, ensure that you are not on an occupied channel. Do not transmit on 121.500MHz, as this is the international distress frequency. Do not transmit into an unterminated antenna line as a suitable antenna must be connected. Transmitting without being connected to an antenna may damage the radio. Ensure that the supply voltage is regulated and does not fall below 11.7 volts DC or exceed 31 volts DC. The transceiver is not waterproof. Do not allow it to get wet. Speaker impedance must be either 4 or 8 ohms (4 ohms preferred) at 5 watts. Use of electret microphones highly recommended. About this document. Due to our policy of continuous improvement to our products and services, technical specifications and claims are correct at time of going to printing, however they are subject to change without notice. Flightline does not accept liability for any error or omission. This manual remains the copyright of Flightline. Page 1 TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS SECTION Page READ ME FIRST ATTENTION ---- READ ME FIRST ATTENTION
....1111 READ ME FIRST ATTENTION ATTENTION READ ME FIRST TA B L E O F C ON T E N TS TA B L E O F C ON T E N TS 2222 TA B L E O F C ON T E N TS TA B L E O F C ON T E N TS 1 INTRODU CTION 1 INTRODU CTION
.. 3.. 3.. 3.. 3 1 INTRODU CTION 1 INTRODU CTION LLATION INSTRUCTIONS 2 INSTAAAALLATION INSTRUCTIONS 2 INST
. 3. 3. 3. 3 LLATION INSTRUCTIONS 2 INST 2 INST LLATION INSTRUCTIONS LLATION CONSIDERATIONS 3 INSTAAAALLATION CONSIDERATIONS 3 INST
.3.3.3.3 LLATION CONSIDERATIONS 3 INST 3 INST LLATION CONSIDERATIONS 4 G EN E R AL 4 G EN E R AL
.4.4.4.4 4 G EN E R AL 4 G EN E R AL 4444 4.1 Sailplanes 4.1 Sailplanes 4.1 Sailplanes 4.1 Sailplanes 4444 4.2 Ultralightssss . 4.2 Ultralight 4.2 Ultralight 4.2 Ultralight 4.34.34.34.3 Microlight / Homebuilt / G.A. Microlight / Homebuilt / G.A. .......4444 Microlight / Homebuilt / G.A. Microlight / Homebuilt / G.A. LLATION INSTAAAALLATION 5 BEFORE BEGINNING INST 5 BEFORE BEGINNING
............5555 LLATION INST 5 BEFORE BEGINNING 5 BEFORE BEGINNING INST LLATION
........ ... identification.. 5.1 Installation parts identification.. 5.1 Installation parts
....5555 5.1 Installation parts
........ identification.. 5.1 Installation parts identification.. 5.2 Transceiver installation and removal 5.2 Transceiver installation and removal ........ ........... 5555 5.2 Transceiver installation and removal 5.2 Transceiver installation and removal General........ 5.3 5.3 5.3 5.3 General
........5555 General General 5.4 Pin connections
.... .. 5.4 Pin connections ... 5555 5.4 Pin connections
... 5.4 Pin connections
... ...5555 5.5 Mechanical installation
... 5.5 Mechanical installation ... .. .. 5.5 Mechanical installation 5.5 Mechanical installation 6666 ectrical installation 5.6 5.6 5.6 5.6 ElElElElectrical installation ectrical installation ectrical installation 5.7 Antenna 5.7 Antenna iiiinstallation.. nstallation.. .............................................................. ...........................7777 nstallation.. 5.7 Antenna 5.7 Antenna nstallation.. ......................................................................................... ........................... ........................... ............................................................. ............................................................. ...7777 Tuning 5.5.5.5.8888 Tuning Tuning Tuning 7777 On air testing 5.5.5.5.9999 On air testing On air testing On air testing 6 OPERATION OF EQUIPMENT 6 OPERATION OF EQUIPMENT 8888 6 OPERATION OF EQUIPMENT 6 OPERATION OF EQUIPMENT
...........8...8...8...8 6.1 General 6.1 General 6.1 General 6.1 General 6.2 Control description 6.2 Control d escription
........8888 6.2 Control d 6.2 Control d escription escription 6.3 Memory programming 6.3 Memory programming 10101010 6.3 Memory programming 6.3 Memory programming
. 10. 10. 10. 10 6.4 Memory delete 6.4 Memory delete 6.4 Memory delete 6.4 Memory delete 6.5 Operation of intercom 6.5 Operation of intercom
. 10
. 10 6.5 Operation of intercom 6.5 Operation of intercom
. 10. 10 6.6 User setting 6.6 User setting
. 10. 10. 10. 10 6.6 User setting 6.6 User setting input 6.7 6.7 6.7 6.7 MusicMusicMusicMusic input
........ 11111111 input input 7 SPECIFICATIONS 7 SPECIFICATIONS 12 12 12 12 7 SPECIFICATIONS 7 SPECIFICATIONS 8 HELPFUL HINTS 8 HELPFUL HINTS
. 13. 13. 13. 13 8 HELPFUL HINTS 8 HELPFUL HINTS WARRWARRWARRWARRANTY ANTY ANTY ANTY EEEEXTERNAL CONNECTIONS XTERNAL CONNECTIONS XTERNAL CONNECTIONS XTERNAL CONNECTIONS Page 2 1 INTRODUCTION 1 INTRODUCTION 1 INTRODUCTION 1 INTRODUCTION Thank you for purchasing this quality product from Flightline. This transceiver has been designed and manufactured in Japan specifically for Ultralights, Gliders and General Aviation Aircraft and Helicopters with size and power consumption as the main considerations. Ease of operation was another primary achievement. Please follow this manual closely to ensure optimum performance, we do hope you have many hours of trouble free communication and safe flying. 2 INSTAAAALLATION INSTRUCTIONS 2 INST LLATION INSTRUCTIONS 2 INST 2 INST LLATION INSTRUCTIONS LLATION INSTRUCTIONS This manual contains all of the necessary instructions for installation and operation. After installation please keep this manual in a safe place for future reference. 3 INSTAAAALLATION CONSIDERATIONS 3 INST LLATION CONSIDERATIONS 3 INST 3 INST LLATION CONSIDERATIONS LLATION CONSIDERATIONS As with all aircraft radios, successful communications start with the installation. After unpacking the transceiver verify all parts against the parts list. Select a suitable mounting area within a maximum 30 degree viewing angle and select a suitable location for operation of ancillary controls, backlight, intercom etc. The use of aviation quality shielded cable is recommended at all times. Avoid running or wrapping other wires around the antenna lead and keep lengths as short as reasonably possible. Ensure that the radio is not exposed to direct rain or moisture (we do not accept liability for water damage). Make sure the transceiver is connected to a 11.7-16.8 volt or 23-33 volt battery system. Do not use AC volts from a Rotax lighting coil. Page 3 4 GENERAL 4 GENERAL 4 GENERAL 4 GENERAL The following section is a guide for individual types of aircraft installations. 4.1 Sailplanes 4.1 Sailplanes 4.1 Sailplanes 4.1 Sailplanes Due to the inherent space restriction on most glider instrument panels the FL-760s 57-mm front panel makes it an excellent choice for confined spaces. Generally the radio is mounted at the bottom of the panel with essential instruments at the top. Location of the ancillary switches should be convenient to the pilot. The Press to Talk (PTT) can be a normally open push-button located on the control column or a handheld microphone. Speakers are normally located at the rear of the pilots head. If not using a handheld microphone, then a boom mike with an electret microphone is preferred. If this radio is to be installed in a motor glider then ensure that the ignition leads are shielded. This will reduce ignition noise considerably. The FL-760 has noise limiting circuitry incorporated and works well in most cases but two stroke interference can be difficult to suppress. 4.2 Ultralight 4.2 Ultralight 4.2 Ultralight 4.2 Ultralight Most ultralights like sailplanes suffer from space restriction. Locate the transceiver with a good viewing angle. Ensure that it is protected from rain (No liability is accepted for water damage). Use shielded aviation quality wire for the headphones, microphone, and speaker. As nearly all Ultralights use two-stroke engines ignition noise can be a problem. Again ensure that all engine high voltage cabling is shielded and grounded. There is almost certainly some background ignition noise with these engines, however, the FL-760 noise limiter will eliminate nearly all of the noise (except for levels around 5 uV). In tandem or side by side seating, use of the intercom provided will work well providing you switch it on. The intercom uses the side-tone feature of the radio and therefore may pick-up some ambient noise. Another feature is the fitting of the external memory toggle switch which when fitted (normally on the control column) allows the pilot to scroll through the memory channels and select scan without reaching for the main channel controls on the radio. This is particularly useful for the rear pilot or instructor in tandem Ultralights or for Helicopter/Gyroplane pilots. 4.3 Microlight / Home built / G.A. 4.3 Microlight / Home built / G.A. 4.3 Microlight / Home built / G.A. 4.3 Microlight / Home built / G.A. In general the same as for ultralights with particular care taken for ignition screening and exposure to rain. Page 4 INSTAAAALLATION 5 BEFORE BEGINNING INST 5 BEFORE BEGINNING LLATION INST 5 BEFORE BEGINNING 5 BEFORE BEGINNING INST LLATION LLATION Again check through the supplied parts list. 5.1 Inst llation parts identification 5.1 Instaaaallation parts identification llation parts 5.1 Inst 5.1 Inst llation parts identification identification All connectors are supplied for installation of this transceiver. Parts include a J001 socket and backshell. Certified aircraft must use approved materials. 5.2 Transceiver installation and removal 5.2 Transceiver installation and removal 5.2 Transceiver installation and removal 5.2 Transceiver installation and removal The following section describes the proper installation and removal of the FL-760 transceiver. 5.5.5.5.3333 General General General General The following information is provided as a guide for installation in uncertified aircraft. If the The following information i s provided as a guide for installation in uncertified aircraft. If the The following information i The following information i s provided as a guide for installation in uncertified aircraft. If the s provided as a guide for installation in uncertified aircraft. If the FLFLFLFL----760 is to be installed in a certifi installation must be done by a certified the installation must be ed aircraft,,,, the 760 is to be installed in a certificatcatcatcated aircraft done by a certified installation must be the ed aircraft 760 is to be installed in a certifi done by a certified done by a certified 760 is to be installed in a certifi ed aircraft the installation must be repair station repair station.... repair station repair station 5.5.5.5.4444 Pin connections Pin connections Pin connections Pin connections Note: If you intend using a dynamic mike (non amplified) you must provide amplification. A Note: If you intend using a dyna mic mike (non amplified) you must provide amplification. A Note: If you intend using a dyna Note: If you intend using a dyna mic mike (non amplified) you must provide amplification. A mic mike (non amplified) you must provide amplification. A Function Function Function Function Microphone Element Microphone Element Microphone Element Microphone Element Microphone Ground Microphone Ground Microphone Ground Microphone Ground Microphone Element Microphone Element Microphone Element Microphone Element Music input Music input Music input Music input Intercom (ground to activate) Intercom (ground to activate) Intercom (ground to activate) Intercom (ground to activate) Squelch output (for limited applications) Squelch output (for limited applications) Squelch output (for limited applications) Squelch output (for limited applications) Press to talk (PTT) (Microphone Key) Press to talk (PTT) (Microphone Key) Press to talk (PTT) (Microphone Key) Press to talk (PTT) (Microphone Key) LED backlight (ground to activate/brightness adjustment by the variable resistor) LED backlight (ground to activate/brightness adjustment by the variable resistor) LED backlight (ground to activate/brightness adjustment by the variable resistor) LED backlight (ground to activate/brightness adjustment by the variable resistor) Positive 12V/24V DC Positive 12V/24V DC Positive 12V/24V DC Positive 12V/24V DC Positive 12V/24V DC Positive 12V/24V DC Positive 12V/24V DC Positive 12V/24V DC Negative ground Negative ground Negative ground Negative ground Negative ground Negative ground Negative ground Negative ground Memory change Memory change Memory change Memory change Headpohne output Headpohne output Headpohne output Headpohne output Speaker output Speaker output Speaker output Speaker output 1111 2222 3333 4444 5555 6666 7777 8888 9999 10101010 11111111 12121212 13131313 14141414 15151515 Pin No. Pin No. Pin No. Pin No. simple 2 transistor amplifier with gain control will do. simple 2 transistor amplifier with gain control will do. simple 2 transistor amplifier with gain control will do. simple 2 transistor amplifier with gain control will do. Can be used the dimmer of the backlight. ((((Refer to user setting of page10 Can be used the dimmer of the backlight. Refer to user setting of page10)))).... Refer to user setting of page10 Can be used the dimmer of the backlight. Can be used the dimmer of the backlight. Refer to user setting of page10 5.5.5.5.5555 Mechanical installation Mechanical installation Mechanical installation Mechanical installation Carefully measure the proposed mounting site for clearance. Allow for rear cabling and connectors. Use the template supplied to carefully drill a 58mm hole. Drill the mounting holes (4mm) The mounting holes support the weight of the transceiver and should not be oversized. Run all wires that will be required for your particular installation. Following are the recommended configurations for use in Gliders and Ultralights:
Following are the recommended configurations for use in Gliders and Ultralights:
Following are the recommended configurations for use in Gliders and Ultralights:
Following are the recommended configurations for use in Gliders and Ultralights:
Page 5 5.5.5.5.6666 Electrical installation Electrical installation Electrical installation Electrical installation Single seat sailplanes:
Single seat sailplanes:
Single seat sailplanes:
Single seat sailplanes:
Power, speaker, microphone (prefer electret), PTT located on control column, backlight switch or volume (for viewing) Two place Two place sailplanes:
sailplanes:
Two place Two place sailplanes:
sailplanes:
Additional wiring should include the memory toggle switch for the rear seat, rear PTT switch and microphone. Motor Glider:
Motor Glider:
Motor Glider:
Motor Glider:
Jack for headset microphone and speaker. Ultrali Ultralights / Microlights:
ghts / Microlights:
Ultrali Ultrali ghts / Microlights:
ghts / Microlights:
Power, Speaker (not for open cockpit design), PTT located on control column, headset microphone (prefer electret), backlight switch or volume, antenna coax type RG58U
(recommend vertical 1/4 wave antenna with ground plane). Tandem/ sid Tandem/ side by side:
e by side:
Tandem/ sid Tandem/ sid e by side:
e by side:
Additional rear seat PTT and headset wiring, memory toggle switch, intercom switch. Having run all the wires we will now terminate them. First connect the power cable to a 14-volt or 28-volt source. It is advisable to run this via a circuit breaker or fuse (2-amp max). NOTENOTENOTENOTE----
The FL 0 amp fusible link which is not field replaceable. If the radio 760 has an internal 10 amp fusible link which is not field replaceable. I The FL----760 has an internal 1 f the radio 0 amp fusible link which is not field replaceable. I 760 has an internal 1 The FL The FL 760 has an internal 1 0 amp fusible link which is not field replaceable. I f the radio f the radio fails it must be returned to a Flightline fails it must be returned to a Flightline approved repair facility. approved repair facility. fails it must be returned to a Flightline fails it must be returned to a Flightline approved repair facility. approved repair facility. RED is POSITIVE! ! ! ! (Pins 9 and 10) GROUND RED is POSITIVE GROUND (Pins 11 and 12) GROUND POSITIVE RED is RED is POSITIVE GROUND It is advisable to connect the power cable through a radio master switch and not direct to the battery. Solder the PTT cable to the J001 with the shield connected to ground and the center conductor to pin 7. The other end of the cable should be connected to the common and normally open contact on the push button switch. If using two switches simply wire them in parallel. Now solder the microphone cable center conductor to pin 3 or 1 (both if two mics are used) on the J001 socket and the shield to ground (Pin2). You can now connect the microphone. If using an electret mic please check that the red wire is connected to the center conductor as these are polarity sensed and reverse polarity will severely damage the mic. If using two microphones then wire to the 2 separate inputs. NOTE NOTE both mics are active on NOTE NOTE transmit. For pilot/copilot isolation order the optional relay board. Now connect the backlight switch using two wires, one to ground and the other to pin 8. You can use volume instead of backlight switch (for brightness adjustment). The switch
(volume) is wired center conductor to common and the other side to ground. THIS IS NOT A THIS IS NOT A THIS IS NOT A THIS IS NOT A switched on or off. MOMENTARY SWITCH, it needs to be switched MOMENTARY SWITCH, it needs to be on or off. switched MOMENTARY SWITCH, it needs to be MOMENTARY SWITCH, it needs to be switched on or off. on or off. Page 6 For Motor Glider and Ultralights install the following intercom switch wiring. Wire the center conductor to PIN 5 and the shield to ground. The switch is the same as for the backlight switch described previously or when the switch is not used, you can use voice operation (VOX function). Memory toggle center conductor to PIN 13 and the shield to ground. The memory toggle switch is momentary type with the center conductor to common and the shield to normally open. You may have noted that nearly all switch connections are to ground, this was done to simplify wiring and avoid any possible shorts to positive voltages. 5.5.5.5.7777 Antenna Installation Antenna Installation Antenna Installation Antenna Installation The following section refers to proper antenna installation. NOTE:
NOTE: In certified aircraft approved antennas must be used. In certified aircraft approved antennas must be used. NOTE:
NOTE:
In certified aircraft approved antennas must be used. In certified aircraft approved antennas must be used. 5.5.5.5.8888 Tuning Tuning Tuning Tuning Before any tuning can be attempted you must have a VSWR meter which can measure the antennas reflected power. The lower the SWR reading the higher the output and the radiated signal. High SWR degrades performance and can cause damage. An SWR of <1.5:1 is desirable. 5.5.5.5.9999 On air testing On air testing On air testing On air testing Before transmitting check all connections and switch on. Operate controls as per section 6. A simple on air test for audio quality on transmit and receive should be done. Have someone monitor your signal on another radio. Transmit and speak into the microphone at normal level. If the received signal is quiet then the mike gain control will need to be adjusted. If the signal is loud and distorted then it will need to be turned down. These adjustments should be done using a comm. test set. Have another radio transmit a test call and monitor the audio quality. With the volume control turned to the 3/4 position the audio should be loud and not distorted. Distortion could be caused by the choice of speaker. A 4 watt speaker is recommended as a minimum power rating. Set the squelch and have the station transmit, the squelch should break crisply and without delay. Note;Note;Note;Note;
Do not transmit on 121.500MHz, as this is the international distress frequency. Do not transmit on 121.500MHz, as this is the international distress frequency. Do not transmit on Do not transmit on 121.500MHz, as this is the international distress frequency. 121.500MHz, as this is the international distress frequency. Page 7 6 OPERATION OF EQUIPMENT 6 OPERATION OF EQUIPMENT 6 OPERATION OF EQUIPMENT 6 OPERATION OF EQUIPMENT 6666....1111 General General General General Please read this section for the cor Please read this section for the correct description and operation of this equipment. rect description and operation of this equipment. Please read this section for the cor Please read this section for the cor rect description and operation of this equipment. rect description and operation of this equipment. 6666....2222 Control Description Control Description Control Description Control Description Following diagram shows the position of the controls. Volume and OnOff control Volume and On Off control Volume and On Volume and On Off control Off control Turn fully anticlockwise to switch off. Turn clockwise to switch on and adjust volume. Squel
(mute) control Squelchchchch (mute) con trol Squel
(mute) con Squel
(mute) con trol trol The outer ring control adjusts the mute threshold. Up/Down PushPushPushPush kHz Up/Down kHz Up/Down Up/Down kHz kHz Turn clockwise or counter-clockwise to change the frequency. Push knob to adjust kHz. Push the knob MHz step kHz step riorityEmergency PPPPriority Emergency riority riority Emergency Emergency Activating this control will switch to priority memory. It also doubles as memory channel delete. Page 8 Press and hold this key for two seconds to activate the emergency frequency. If the external memory button is pushed after the priority memory is called, it becomes a priority scan. LED Indicator LED Indicator LED Indicator LED Indicator A clear display indicates a muted receive condition. Steady green indicates Squelch open or a signal present. Steady red indicates a transmit condition. Flashing red indicates that the PTT has been on for longer than 50 seconds. If the radio senses that the PTT has been pressed for more than five minutes (three minutes or one minute is also selectable) the radio will automatically cease transmission.
(This is helpful for indicating a possible stuck PTT or mike switch). ModeModeModeMode Selects five display pages. A Default is 2 line frequency displays. The top line is the active frequency and the bottom line is the standby frequency. Tuning the dial left or right will channel the MHz and pressing the knob once will activate the kHz channeling (after 5 seconds of inactivity it will revert to MHz). To transfer the standby frequency to the active simply hit the transfer button (arrowed switch) once. Remember, the top line is always the active frequency. B Push in the mode button again to access the VFO scan display. To VFO scan hit the arrow key. C Push the mode button again to access the memory channel display. There are 32 memory channels that can be displayed. Turn the dial left or right to move the channels up or down. To scan, hit the arrow key. To stop scanning, hit the arrows or activate the PTT. Note: If the memory channel is empty it will not be displayed. Note: If the memory channel is empty it will not be displayed. Note: If the memory channel is empty it will not be displayed. Note: If the memory channel is empty it will not be displayed. D Push the mode button again to access the priority memory channel display. To priority scan, press the arrow key. The unit will now scan between the memory channel and priority channel. E Push the mode button again to access the program page. Page 9 External memory External memory toggle toggle External memory External memory toggle toggle This button alternately replaces an active frequency and the standby frequency. Active Standby 6666....3333 Memory programming Memory programming Memory programming Memory programming 1 The top line should read memory channel 1 (1 to 32 and PRI). 2 Select the required memory number with the up/down dial. 3 Next push the dial to select the bottom line MHz. 4 Now enter the desired frequency. 5 Push the dial again to enter the kHz and adjust. 6 Next push the arrows button, the memory number will flash then programmed will appear. You now have a programmed memory channel. 7 Repeat this operation for other memory channels. 8 Up to 32 channels can be programmed. 9 Only programmed channels will be displayed. 10 By programming a frequency into Memory PRI this will give you a priority selection. 6666....4444 Memory delete Memory delete Memory delete Memory delete 1 The top line should read memory channel 1 (1 to 32 and PRI). 2 Select the required memory number with the up/down dial. 3 Push the PRI button, the memory channel is deleted. 6666....5555 Operation of intercom Operation of intercom Operation of intercom Operation of intercom Internal adjustment of the sidetone volume may need to be done to set the correct level. In a noisy environment reducing the microphone gain may also be required. Do not Do not Do not Do not adjust the modulation adjust the modulation!!!! A wind sock over the mike will also help reduce noise. modulation adjust the adjust the modulation The VOX operation can be used and sensitivity can be set in the user setting mode. Note: VOX (Voice----operated Transmission) Note: VOX (Voice operated Transmission) Note: VOX (Voice Note: VOX (Voice operated Transmission) operated Transmission) 6666....6666 User setting User setting User setting User setting You can set the use of this radio. Continuous on of the backlight. Hold down the MOD button and power on. Push the MOD button and select the LAMP. Push the dial switch and select the OFF or ON. Push the arrow key, enter the backlight function. you select the on, you can not adjust the dimmer. Note: If you Note: If select the on, you can not adjust the dimmer. you you Note: If Note: If select the on, you can not adjust the dimmer. select the on, you can not adjust the dimmer. Automatic voice operation control gain for intercom. Hold down the MOD button and power on. Push the MOD button and select the VOX. Push the dial switch and select the HI, MID1, MID2 or LO. Push the arrow key, enter the VOX sensitivity. Time out time of transmit. Hold down the MOD button and power on. Push the MOD button and select the TOT. Push the dial switch and select the OFF, 01, 03 or 05 (minutes). Push the arrow key, enter the TOT time. Page 10 Busy lockout of transmit. (If the radio is receiving a signal then it can not transmit) Hold down the MOD button and power on. Push the MOD button and select the BLO. Push the dial switch and select the OFF or ON. Push the arrow key, enter the busy lockout function. 6666....7777 Music Music Music Music input input input input You can listen to music. The music will automatically mute when radio or intercom traffic is detected. Connection example Music player Stereo to monoral conversion Music will remain muted for three seconds after the last transmission. Page 11 7 SPECIFICATIONS 7 SPECIFICATIONS 7 SPECIFICATIONS 7 SPECIFICATIONS GGGGeneral eneral eneral eneral Frequency range Channel spacing Mode Number of memory channels Acceptable power supply Usable temp. range Frequency stability Current drain Dimensions Weight Exposed dial face Transmitter Transmitter Transmitter Transmitter Output power Modulation Modulation limiting Audio harmonics distortion Hum and noise ratio Spurious emissions Antenna impedance Receiver Receiver Receiver Receiver Receive system Intermediate frequency Sensitivity (at 6dB S/N) Squelch sensitivity Selectivity Spurious response rejection Audio output power Side tone Hum and noise Audio output impedance
: 118.00 to 136.975MHz (Receive:108.00 to 136.975MHz)
: 25kHz
: AM (6K00A3E)
: 32
: 11.7 V or 33 VDC (Negative ground only)
: -20 to +60
:+/- 5ppm
: TX: 3A(max) RX 0.8A(max) Standby: 300mA
: W61 X D159 X H61 (mm)
: 430g
: 56.4mm 2 1/4.5 inches
: 5 W (carrier), 16W (pep)
: small stage modulation
: 70 to 100%
: Less than 15% (at 85% modulation)
: More than 40dB
: -16dBm or less
: 50
: Double conversion superheterodyne
: 1st : 38.85MHz (Upper) 2nd : 450kHz (Lower)
: Less than 1uV
: 0.5uV (Threshold)
: More than 8kHz (at 6dB)
: Less than 25kHz (at 60dB)
: More than 60dB
: More than 4W (at 4)
: More than 100mW (at 600)
: More than 30dB
: Ext. SP 4 (4 to 8) Side tone 600 Accessories Accessories Accessories Accessories D-SUB-15 connector (female) and cover X 1 Screw for mount (6-32) X 4 Installation/Operations Manual X 1 Page 12 HELPFUL HINTS 8 8 8 8 HELPFUL HINTS HELPFUL HELPFUL HINTS HINTS Installing an inline power filter consisting of an LC network may reduce stubborn ignition noise. These are readily available and are commonly used to suppress noise getting into stereo systems. Use shielded spark plug leads. Try to avoid mounting the dial face in direct sunlight the plastic may melt. (It is designed to withstand 80 deg C however cockpit temperatures can well exceed this). Notes on using the ICOM boom microphone this mike will not perform well compared to a pure electret, there is not a great deal that can be done other than replacing the microphone. Make sure your microphone has a wind sock as this will substantially reduce background noise. General General General General The key to a successful radio installation is an effective antenna system. Antenna selection and proper termination and tuning will make a difference. The following antennas are recommended:
Sailplanes:
Sailplanes:
Sailplanes:
Sailplanes:
Vertical 1/2 wave coax dipole mounted in the tail. Another choice is a 1/4 wave vertical mounted in the fuselage for wooden or fiberglass and externally on the top for metal. If mounted in wooden or GRP aircraft you must provide a ground plane. Ultralights:
Ultralights:
Ultralights:
Ultralights:
The 1/4 wave ground plane is by far the most popular and makes an effective antenna. Again a proper ground plane is essential. Homebuilt aircraft Homebuilt aircraft::::
Homebuilt aircraft Homebuilt aircraft As above. Page 13 Certified Aircraft:
Certified Aircraft: Any approved VHF communications antenna Certified Aircraft:
Certified Aircraft:
6.5mm (1/4") 3.2mm (1/8") 1.6mm (1/16") BNC termination BNC termination BNC termination BNC termination Coaxial cable termination Coaxial cable termination Coaxial cable termination Coaxial cable termination Radio hole cutout dimensions (drawing not to scale) Radio hole cutout dimensions (drawing not to scale) Radio hole cutout dimensions (drawing not to scale) Radio hole cutout dimensions (drawing not to scale) Page 14 Limited Liability Warranty Limited Liability Warranty Limited Liability Warranty Limited Liability Warranty Flightline warrants this product to be free from defects in materials and workmanship for 1 year from the date of purchase or the minimum period described by applicable consumer law. If the unit is installed by an organization which holds an avionics installation approval from the FAA, and that organization has co-signed and dated the warranty card, the warranty period shall be deemed to commence from the date of installation. The customer shall be responsible for any transportation costs for return of this product to Flightline. This warranty does not cover failures due to abuse, misuse, accident, unauthorized alteration, or repairs carried out by parties other than Flightline or an approved Flightline service center. This warranty does not cover failures where the product has not been installed or operated, in accordance with the provisions of the User and Installation manual(s). It shall be at Flightline sole discretion to decide if a defect is a result of material or workmanship failure. THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, INCLUDING ANY LIABILITY ARISING UNDER WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, STATUARY OR OTHERWISE. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH MAY VARY FROM STATE TO STATE, AND COUNTRY TO COUNTRY. IN NO EVENT SHALL FLIGHTLINE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, WHETHER RESULTING FROM THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT OR FROM DEFECTS IN THE PRODUCT. Flightline may at it discretion, refer product returns for repair or service, to a service facility closest to you. Flightline reserves the right to repair or replace the unit or software or offer a full refund of the purchase price at its sole discretion. SUCH REMEDY SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY. Supplied by:
Supplied by:
Supplied by:
Supplied by:
Flightline 2008 All Rights Reserved 00M52AC851010 Printed in Japan February 2008 Page 15
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2008-02-28 | 118 ~ 136.975 | TNB - Licensed Non-Broadcast Station Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2008-02-28
|
||||
1 | Applicant's complete, legal business name |
EDMO Distributors, Inc
|
||||
1 | FCC Registration Number (FRN) |
0007410525
|
||||
1 | Physical Address |
12830 E. Mirabeau Parkway
|
||||
1 |
Spokane, Washington 99216
|
|||||
1 |
United States
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
h******@atcb.com
|
||||
1 | TCB Scope |
B3: Maritime & Aviation Radio Services equipment in 47 CFR parts 80 & 87
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
VOS
|
||||
1 | Equipment Product Code |
FL760A
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
T****** K******** G****
|
||||
1 | Title |
Director
|
||||
1 | Telephone Number |
509-5********
|
||||
1 | Fax Number |
509-5********
|
||||
1 |
t******@edmo.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | TNB - Licensed Non-Broadcast Station Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | VHF AM TRANSCEIVER | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Power output listed is at the antenna connector. Only those antenna(s) tested in the fiilng or antenna(s) of equal or lesser gain and type may be used with this device. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
n/a | ||||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 87 | 118.00000000 | 136.97500000 | 9.4000000 | 1.5000000000 ppm | 6K00A3E |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC