FCC ID: A5FEIA600MRF Ei Electronics RF Transceiver for EiA600 Series Smoke/Heat Alarms

EiA600MRF RF Module Installation Instructions Notice dInstallation Module Removal & Installation The RF module is supplied pre-fitted and should never have to be removed by the user. If a situation arises where the module must be removed the following instructions must be carefully followed. To remove the module, carefully use the pull tag to remove the module from the Alarm. To refit the module plug it into the base of the Alarm while being careful to align the connector pins and insert the flexible antenna into the antenna hole (See Fig 1). N.B. Ensure that the module is fully inserted. The RF module will be pre-installed by the manufacturer. If the RF module is removed and fitted to another host Alarm, a label displaying, Contains FCC ID: A5FEIA600MRF Contains IC:

22380-EIA600MRF must be placed on the new host Alarm, visible when installed (see Fig 2). This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. RF Exposure: This equipment must operate with a separation distance of at least 20cm from all persons This device complies with ISEDs license-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. RF Exposure: This equipment must operate with a separation distance of at least 20cm from all person Retrait & Installation du Module Le module est pr-install. Pour retirer le module de lavertisseur, tirer dlicatement sur la languette. Pour remettre le module en place, inserez-le larriere de lavertisseur en faisant attention bien aligner les broches et insrez lantenne flexible dans le trou conu cet effet

(voir Fig 1). N.B. Assurez-vous que le module est compltement insr. Le module RF vient pr-install par le fabricant. Si le module est enlev et install sur un autre Avertisseur, ltiquette affichant lidentifiant Contient lID FCC: A5FEIA600MRF contient IC: 22380-EIA600MRF visible lors de linstallation (voir Fig 2) doit tre place sur le nouvel avertisseur o le module est maintenant install. Cet appareil est conforme la partie 15 des rgles de la FCC amricaine. Son fonctionnement est soumis aux deux conditions suivantes :

(1) cet appareil ne doit pas provoquer dinterfrences nuisibles et

(2) cet appareil doit accepter toutes les interfrences, y compris celles qui pourraient provoquer un fonctionnement non souhaitable. Exposition RF: Cet quipement doit fonctionner avec une distance de sparation dau moins 20 cm de toutes les personnes FCC ISED FCC ISED House Code Button Bouton Inclusion Antenna Antenne Top Side Face suprieure Bottom Side Face infrieure LED DEL Connector Pins Broches de connecteurs Figure 1 Contains FCC ID: A5FEIA600MRF Contains IC: 22380-EIA600MRF Cet appareil est conforme aux RSS exemptes de licence de lISED. Le fonctionnement est soumis aux deux conditions suivantes:

(1) Cet appareil ne doit pas provoquer dinterfrences; et

(2) Cet appareil doit accepter toute interfrence, y compris celles pouvant entraner un fonctionnement indsirable de lappareil. Figure 2 Contains FCC ID: A5FEIA200MRF Contains IC: 22380-EIA200MRF Exposition RF: Cet quipement doit fonctionner avec une distance de sparation dau moins 20 cm de toutes les personnes Please return to / Veuillez retourner lappareil :

Customer Service / Service la clientle Ei Electronics US, Inc, 2 Tunxis Road, Suite 209, Tariffville, Connecticut 06081 web: www.ei-electronics.com Ei Electronics 2020 P/N B20014 Rev0

EiA600MRF FCC/IC Label and Unit Label Label to be permanently fixed to the RF module FCC/ISED label to be placed on outside rim of Host Alarm

11/11/2019 Telecommunication Certification Body UL VS Ltd Unit 3, Horizon Wade Road Kingsland Business Park Basingstoke Hampshire RG24 8AH United Kingdom Subject: Authorisation Letter To whom it may concern Yours faithfully, Eric Duignan Compliance Manager This is to certify that Ei Electronics hereby authorises UL VS Ltd. to act as the TCB for the application of the EiA600MRF, FCC ID: A5FEIA600MRF to the FCC. We certify that we are not subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47 CFR 1.2002(b) for the definition of a "party" for these purposes.

11/11/2019 Telecommunication Certification Body UL VS Ltd Unit 3, Horizon Wade Road Kingsland Business Park Basingstoke Hampshire RG24 8AH United Kingdom Subject: Permanent Confidentiality Request Certification Application FCC ID: A5FEIA600MRF To whom it may concern Yours faithfully Eric Duignan Compliance Manager Pursuant to Sections 0.457(d) and 0.459 of CFR 47 , Ei Electronics request that the following information, provided to support the FCC application for the EiA600MRF FCC ID:

A5FEIA600MRF be held permanently confidential:

Schematics Block Diagrams Operational Description The above material contains trade secrets not customarily released to public that are judged to have the potential to cause detriment to the applicant and provide unjustified benefits to its competitors. This information should not be available for public disclosure for an indefinite period of time.

11/11/19 Telecommunication Certification Body UL VS Ltd Unit 3, Horizon Wade Road Kingsland Business Park Basingstoke Hampshire RG24 8AH United Kingdom Subject: FCC Limited Modular Approval Letter FCC ID: A5FEIA600MRF To whom it may concern We, Ei Electronics, hereby declare that the product EiA600MRF, FCC ID: A5FEIA600MRF has met the limited modular approval requirements of FCC rule part 15.212(a)(1) and this is shown in the table below. The product will be fitted into the EiA660W & EiA660iW Multi-Sensor Alarms and the EiA630W & EiA630IW Heat Alarms to provide interconnection to other devices. Requirement Compliance: Yes or No with justification The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal The module must contain power supply regulation on the module No The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per Sections 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b) The module must demonstrate compliance in a stand-alone configuration The module must be labelled with its permanently affixed FCC ID label, or use an electronic display

(See KDB Publication 784748 about labelling requirements) The module must comply with all specific rules applicable to the transmitter including all the conditions provided in the integration instructions by the grantee The module must comply with RF exposure requirements Yes - All modulation and data inputs are buffered by circuitry on the transmitter chip. Yes - Power supply regulation is provided by circuitry on the transmitter chip Yes The antenna is permanently attached. It is a wave whip antenna with 0Bi gain No Modules must be fitted to compatible devices Samples of the host labels are provided as an exhibit, showing the FCC identifier of the modules. The modules comply fully with the operating requirements of Part 15 section FCC Part 15.249 as demonstrated in the test reports exhibit. the module complies with FCC part 2.1091 for operation at >20cm usage Yours faithfully, Eric Duignan Compliance Manager