Smart Video Doorbell
T8
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:(1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF exposure statement:
To maintain compliance with FCC’s RF Exposure guidelines, This
equipment should be installed and operated with minimum distance
between 20cm the radiator your body.
User Manual 1.0
Features
1. Motion Sensor
2. Wide-angle Lens
3. Hidden Infrared Lights
4. Light Sensor
5. Microphone
6. Doorbell Button
7. Indicator Lights
8. Speaker
9. Micro USB Port (Battery Charging)
Indicator Light
In the box
Indicator light flashing RED
The device is reconnecting to the
Wifi network. Please wait.
Indicator light flashing RED
and BLUE alternately
Low battery. Please recharge your
batteries.
Video Doorbell
Tape
2 Anchors
Video
Doorbell
2 Screws
User Manual
2 Batteries
(Optional)
Chime
(Optional)
Charge batteries
1. Remove the battery tab.
2. Insert 18650 batteries
positive end facing down,
as shown on the device.
Rechargeable 18650 Battery
3. Fully charge batteries by connecting your device to a
USB charger using a Micro USB cable. It takes about
14 hours for batteries to fully charge.
WARNING: Lots of events
If your device is capturing an excessive number of
events every day, you might need to recharge your
battery sooner. Plus, the battery is also drained each
time you use the Live View to look or speak through
your doorbell. To prevent excessive events, you can
adjust your motion settings to a lower sensitivity.
Set up your Video Doorbell
Before You Start
1. Download and install Aiwit App.
Scan the QR code below or search for Aiwit on the
Apple App Store or Google Play. Download and install
the app.
2. Create an Aiwit account.
Aiwit
Android / iOS
App Download
Set up your device in the Aiwit app.
To pair your device, follow the steps below and in-app
instructions.
1. Open Aiwit App and log in to your account.
2. To add your camera, select the + icon.
3. Select Video Doorbell.
4. Press and hold the Doorbell Button until the red light
is flashing, tap Next, then tap Yes.
5. Enter your 2.4GHz Wi-Fi network and the Wi-Fi
password, then tap Next (5GHz is not supported).
6. Use your device camera to scan the QR Code shown
on the app, then select Confirm once the Wi-Fi setup
has finished.
4 inches (10 cm)
Install your Video Doorbell
Mark drill holes and use a bit to drill holes in your wall.
Insert anchors and secure your doorbell with mounting
and security screws.
Step 1
Step 2
Wall
Frequently asked questions
How to RESET the doorbell
Press and hold the Doorbell Button for 8 seconds. Then
follow the in-app instructions to finish your Wi-Fi setup.
How to share the device with my family
Open the Aiwit app. From the home page, tap the Share
icon. Tap Share via Email or Share via QR Code. You can
share the device with up to 8 users.
Share via Email:
The new user has to download the Aiwit app and
create an account with the same email address which
the device owner has shared with. Log in to the
account and you'll see the shared device.
Share via QR Code:
1. Open the Aiwit App on a new user's smartphone.
2. From the home page, tap +.
3. Tap QR Code Sharing, then scan the QR code the
device owner generated before.
4. You will see Share successful, then tap Confirm.
How many users can view the video at the same time?
Up to 3 users may view the video feed, but only 1 user
can use the direct intercom. Both iOS and Android are
compatible
Is 5GHz Wi-Fi supported?
No. Only 2.4GHz Wi-Fi is supported.
Why is my Wi-Fi signal poor on my device?
Your device may be too far away from your wireless
router or you may have some obstructions in between
that reduce signal strength. You might try repositioning
your router or getting a signal extender/repeater for
your wireless router.
How to adjust Motion Detection Sensitivity
From the home page, tap the Motion Detection icon.
Motion Detection Sensitivity
• Fast: Records and notifies you about every motion.
Shortest battery life.
• Medium: Records and notifies you about motion less
often. Standard battery life.
• Slow: Records and notifies you about motion even less
often. Maximum battery life.
How to enable Notifications on my phone
To do this, you need to give permission for the Aiwit app
to access to your microphone and enable notifications.
Follow these steps to enable notifications.
1. Open Settings. Go to Aiwit app permissions and
select Notifications.
2. Make sure all switches are on.
Set up your Wireless Chime (Optional)
Connect the video doorbell to the doorbell chime, and
get instant alert in your home when someone rings the
doorbell. The chime plugs into any wall outlet, you can
place it anywhere in the home.
NOTICE:
The video doorbell is only compatible with our wireless
chime, and not compatible with traditional doorbell chimes.
The wireless chime is optional. If it is not installed, doorbell
notifications will still go directly to the Aiwit app.
The Basics
Volume
down
Volume
up
Tune
Connect
Set up your chime with the video doorbell.
Step 1
Before the setup process, be sure your video doorbell has
connected to your phone and plug in your chime.
Step 2
Step 3
Press the Connect Button.
Press the Doorbell Button
to pair your doorbell to the
chime.
Step 4
Step 5
Press the Tune Button to
cycle through 38 different
tunes and select a tune.
Press the Doorbell Button
again to make sure it’s the
tune you selected.