FCC ID: WP5TWN4F11 RFID module

Transponder Reader TWN4 Palon Compact LEGIC Integration Manual Rev. 1 Elatec GmbH 1. Introduction The transponder reader TWN4 Palon Compact LEGIC is a device for reading and writing RFID transponders. There are different versions of TWN4 devices available, which cover a large range of transponder types both in the frequency range of 125 kHz and 13.56 MHz. 2. Getting Started 2.1 Cable Connection In order to start operating a TWN4 Palon Compact LEGIC transponder reader, it simply has to be connected to a host. 2.2 Power Up Once a TWN4 Palon Compact LEGIC reader is connected to the host, it detects the type of communications cable (USB or RS232), with which it is connected to the host. Additionally, the RS232 is sending a version string via RS232 to the host. Page 2 of 15 2.3 Enumeration (USB Only) Elatec GmbH This is only applicable for the USB version: Once the device has been powered up, it is waiting for completion of the enumeration by the USB host. As long as the device is not enumerated, it is entering a minimum power consumption mode, where both LEDs are turned off. 2.4 Initialization After powering up and enumeration (in USB mode), the device is turning on the built-in transponder reader logic. The green LED is turned on permanently. Some transponder reader modules need some kind of initialization, which is performed in this step. After successful initialization, the device sounds a short sequence, which consists of a lower tone followed by a higher tone. 2.5 Normal Operation As soon as the device has completed the initialization, it is entering normal operation. During normal operation the device is searching for a transponder continuously. Page 3 of 15 Elatec GmbH 2.6 Detection of a Transponder If a transponder is detected by the reader, following actions are performed Send the ID to the host. By default, the USB device sends by emulating keystrokes of a keyboard. A RS232 device sends the ASCII code of an ID. Sound a beep Turn off the green LED Blink the red LED for two seconds Turn on the green LED Within the two seconds timeout, where the red LED is blinking, the transponder, which just has been recognized will not be accepted again. This prevents the reader from sending identical IDs more than one time to the host. If during the two seconds timeout of the red LED a different transponder is detected, the complete sequence restarts immediately. 2.7 Suspend Mode (USB Only) The USB version of the transponder reader supports the USB suspend mode. If the USB host is signaling suspend via the USB bus, the transponder reader is turning off most of its power consuming peripherals. During this operation mode, no detection of transponders is possible and all LEDs are turned off. Once the host is resuming to normal operation mode, this is also signaled via the USB bus. Therefore, the transponder reader will resume to normal operation, too. Page 4 of 15 3. List of Antennas Elatec GmbH 125 kHz antenna 13,56 MHz antenna Page 5 of 15 Elatec GmbH 4. Power Supply In case of USB connection, the input voltage is 4.3V to 5.5V. If the device is supplied via the terminal block, the input voltage is 9V to 30V. 5. Pinout Page 6 of 15 Elatec GmbH 6. External Antenna Please note: Connecting an antenna to the UMCC connector is not included in the approvals of the device. In this case, the device requires separate approval with that specific antenna. Page 7 of 15 7. Compliance statements Elatec GmbH 7.1 RF module USA (FCC)

(RF module) Compliance statement:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Modification of equipment:

The instruction manual of the host shall include the following statement:

Changes or modifications made to this equipment not expressly approved by the party responsible for compliance may void the FCC authorization to operate this equipment. Information to the user:

(The instruction manual of the host shall include the following statement) A compliance statement as applicable, e.g., for devices subject to part 15 of CFR 47 as specified in 15.19(a)(3), that the product complies with the rules; and the identification, by name, address and telephone number or Internet contact information, of the responsible party, as defined in 2.909. The responsible party for Suppliers Declaration of Conformity must be located within the United States. Page 8 of 15 Elatec GmbH CANADA (ISED) This device complies with Industry Canadas license-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

1) lappareil ne doit pas produire de brouillage;

2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Page 9 of 15 Elatec GmbH 7.2 Host device USA (FCC) FCC notes for a host subject to SDoC:

For a host device assembled with the certified module and subject to 47 CFR Part 15, the following statements have to be included in the user manual and the host device has to be labelled as noted below. If the host device is subject to other authorization procedures or parts, the appropriate requirements of these authorization procedures or parts apply. Important note:

OEM integrator is still responsible for the FCC compliance requirements of the end product, which integrates this module. Appropriate measurements as described in KDB 996369 D04 Module Integration Guide and, if applicable, additional equipment authorization of the host device have to be addressed by the integrator/ manufacturer The end device must be labeled with:

Contains FCC ID: WP5TWN4F11 Page 10 of 15 Elatec GmbH For class B devices:

FCC 15.105 (b):

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Connect the equipment into an outlet on a circuit different from that Increase the separation between the equipment and receiver. to which the Receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. For class A devices:

FCC 15.105 (b):

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Page 11 of 15 Elatec GmbH Special accessories:

Where special accessories such as shielded cables and/or special connectors are required to comply with the emission limits, the instruction manual shall include appropriate instructions on the first page of the text describing the installation of the device. Simultaneous transmission:

When the host product supports simultaneous-transmission operations the host manufacturer needs to check if there are additional RF exposure filing requirements due to the simultaneous transmissions. When additional application filing for RF exposure compliance demonstration is not required

(e. g. the RF module in combination with all simultaneously operating transmitters complies with the RF exposure simultaneous transmission SAR test exclusion requirements), the host manufacturer may do his own evaluation without any filing, using reasonable engineering judgment and testing for confirming compliance with out-of-band, restricted band, and spurious emission requirements in the simultaneous-transmission operating modes. If additional filing is required please contact the person at ELATEC GmbH responsible for certification of the RF module. Page 12 of 15 Elatec GmbH CANADA (ISED) This device complies with Industry Canadas license-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

1) lappareil ne doit pas produire de brouillage;

2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Important note:

OEM integrator is still responsible for the ISED compliance requirements of the end product, which integrates this module. Appropriate requirements as described in RSS-GEN have to be fulfilled by the integrator/ manufacturer. Labeling requirements for Host device:

For Host devices subjected to ICES-003, the appropriate labeling requirements apply. CAN ICES-3 (*)/NMB-3(*)

* Insert either A or B but not both to identify the applicable Class of ITE. The end device must be labeled with:

Contains IC: 7948A-TWN4F11 Page 13 of 15 Elatec GmbH NCC Warning Statement

(OEM Integrator)(End Product) NCCCCXXxxYYyyyZzW Page 14 of 15 Elatec GmbH Service Address In case of any technical questions, please contact:

Elatec GmbH Zeppelinstr. 1 82178 Puchheim Germany Phone: +49 (0) 89 5529961 0 Fax: +49 (0) 89 5529961 129 Email: info-rfid@elatec.com Page 15 of 15

ELATEC 20200402 S/N 2020081224 Model: TWN4 Palon Compact LEGIC BIB1.08/NKB3.12/STD2.02/B/BT1.07EL ee

: FCC ID: WPSTWNAFIT << I 5 AL IC: T948A-TWNAFIY AA, x HVINEL20201 at

& duct: RFID READER (ADPM) a iCE 9: 5Vde, OSA (Via USB) i me Pet:

4 Nees a

Long/Short-term Confidentiality Request WP5TWN4F11 Date: 07 May 2020 PHOENIX TESTLAB GmbH Product Certification Knigswinkel 10 D 32825 Blomberg FCC ID:

To Whom It May Concerns, Pursuant to sections 0.457(d) and 0.459 of CFR 47 and to avoid premature release of sensitive information prior to marketing or release of the product to the public, we hereby request long-term confidential treatment of information accompanying this application as outlined below:

Schematics Block Diagram Operational Description In addition we hereby request the following exhibits contained in this application to be temporarily (short-term confidentiality) withheld from the public disclosure for an initial period of days External Photos Internal Photos The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to rule 0.457(d), disclosure of this application and all accompanying documentation will not be made before the date of the GRANT for this application. If you have any questions, please feel free to contact me. Yours sincerely, Printed Name: Christian Kiermeier Position: Agent Parts List Tune-Up Info Test Setup Photos Users Manual until:

not applicable

ELATEC GmbH Zeppelinstr. 1 82178 Puchheim Germany Phoenix Testlab GmbH Product Certification Koenigswinkel 10 32825 Blomberg REQUEST FOR FCC Part 15 MODULAR TRANSMITTER APPROVAL FCC ID: WP5TWN4F11 To Whom It May Concern:

Puchheim, 19.06.2020 We, Elatec GmbH, hereby request a modular / limited modular approval. In CFR47 15.212 Modular Transmitters and KDB 996369 D01 Module Equip Auth Guide there are following eight numbered requirements defined:

1. The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly. 125 kHz(LF):

13.56 MHz (HF):

The transmitter is shielded under a common shield for LF and HF. The transmitter is shielded under a common shield for LF and HF. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with part 15 requirements under conditions of excessive data rates or over-modulation. 125 kHz (LF):

13.56 MHz (HF):

The digital transmission signal is decoupled by a buffer from the antenna output signal. The RF signal is generated in a integrated circuit (RF frontend), which is controlled digitally and contains buffers to decouple antenna signal from digitally control signals. 3. The modular transmitter must have its own power supply regulation on the module. All transmitter circuitry is supplied by a linear voltage regulator (3.3V), which is located on the module. ELATEC GmbH HYPOVEREINSBANK MNCHEN Zeppelinstr. 1 82178 Puchheim Germany P +49 89 552 9961 0 F +49 89 552 9961 129 info@elatec.com elatec.com CEO: Stefan Haertel VAT-ID: DE129336743 Amtsgericht Mnchen HRB 85529 IBAN EUR: DE57 7002 0270 0047 8255 47 Swift/BIC: HYVEDEMM IBAN USD: DE29 7002 0270 0847 8271 49 Swift/BIC: HYVEDEMM UNICREDIT BANK CZECH REPUBLIC A.S. CZK-A/C: 1002 7346 51 Bank code: 2700 BANK POLSKA KASA OPIEKI S.A. PLN-A/C: 0912 4060 0311 1100 1042 9885 45 BIC Code: PKOPPLPW 4. The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b). The module consists off two PCBs. PCB #1 contains transmitters for LF, HF plus system on chip PCB #2 contains LF and HF antenna. The two PCBs are connected via specific antenna connector, which ensures connecting only the intended PCB #1 and PCB #2. 5. The module must demonstrate compliance in a stand-alone configuration. The module can be operated in a stand-alone configuration via USB. 6. The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number (KDB 784748). The module is equipped with a permanently affixed label, which displays the FCC identifaction number. 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements The operating requirements are specified as part of a datasheet plus a technical handbook, which are available to the customer. 8. The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. Transmitters according to 15.209 and 15.225 are categorical exempted. Yours sincerely, Signatory Christian Kiermeier Agent 2

ELATEC aleaeee PHOENIX TESTLAB GmbH Product Certification Department K6nigswinkel 10 D 32825 Blomberg To Whom It May Concern:

Please be advised that we ELATEC GmbH authorize the following persons from EMV Testhaus GmbH:

e Mr. Christian Kiermeier e Mr. Rainer Heller e Mr. Konrad Graf to handle the application of Type Approval Services for the following countries:

USA Canada Unless future correspondence from us, please extend your full cooperation to EMV Testhaus GmbH regarding matters to 12 months after the signatory date of this authorization. Contact person Birgit Bachl Position inthe company __ International Comliance Management Date of signatory 06.05.2020 as ono eete SE X +49 89 55;

Signatory Io RFD @ekaie com wun Elolac pee