FCC ID: 2AIBX-NIULL NIUL

USER MANUAL 802.11 b/g/n, 1T1R 2.4GHz Module Model: NIU-LIGHT WN3602M (3.3V/5V) Page 1/10 2021/7/28 PRODUCT FEATURES IEEE 802.11b/g/n, 11 SISO 2.4 GHz Compact Form Factor: 30x17x1mm (PCB) 0.1mm Integrated CPU, memory, MAC, DSSS/OFDM baseband, direct conversion RF radio, encryption CMOS and low-swing sine wave input clock Low-power with deep sleep and standby modes Integrated T/R switch, PA, and LNA HF/RoHS compliance PRODUCT SPECIFICATIONS MAIN CHIPSET NXP 88MW320 FUNCTIONAL SPECIFICATIONS WiFi Function Standard Bus Interface Data Rate IEEE802.11b; IEEE 802.11g; IEEE 802.11n UART 802.11b:

11, 5.5, 2, 1 Mbps 802.11g:

54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11n:

MCS 0 to 7 Media Access Control CSMA/CA with ACK Modulation Techniques Network Architecture Operation Channel Frequency Range 802.11b:

CCK, DQPSK, DBPSK 802.11g:

64QAM, 16QAM, QPSK, BPSK 802.11n:

BPSK, QPSK, 16QAM, 64QAM Ad-hoc mode (Peer-to-Peer) Infrastructure mode 2.4GHz 11: (Ch. 1-11) United States 13: (Ch. 1-13) Europe 14: (Ch. 1-14) Japan 802.11bg 2.412 ~ 2.462 GHz Page 2/10 2021/7/28 Transmit Output Power 1x1

(Tolerance: +-1.5dBm) 802.11b:

16dBm 802.11g:

16dBm 802.11n:

13dBm Receive Sensitivity 802.11b: (IEEE Standard <-76dBm) typical: -87.5dBM(1M) 802.11g: (IEEE Standard <-65dBm) Typical: -73dBm(54M) 802.11n:

20MHz (IEEE Standard <-64dBm) Typical: -71dBm Security WPA, WPA2, WPS, WEP 64/128, IEEE 802.11x, IEEE 802.11i Operating Voltage 5V or 3.3V 10% supply voltage Power Consumption

(Average) TBD Antenna Type Printed Antenna Page 3/10 2021/7/28 PIN DEFINITION UART2_RX UART0_RX UART0_TX 5V 3.3V GND RESET BOOT GPIO10 PIN Name 1 2 3 4 5 6 7 8 9 10 GPIO9 11 GPIO8 12 GPIO7 13 GPIO6 14 UART1_RX 15 UART1_TX 16 UART2_TX Type I I O P P GND I I/O I I I/O I O I O O 5V Power in 3.3V Power in Ground IC Reset JTAG-TRST JTAG-TDI JTAG-TMS JTAG-CLK JTAG-TDO Page 4/10 2021/7/28 MECHANICAL WN3602M (3.3V) WN3602M (5V) Unit : mm ; Tolerance : +/- 0.1mm RECOMMEND FOOTPRINT Unit : mm Page 5/10 2021/7/28 ENVIRONMENTAL Operating Operating Temperature: 0 to 70 C Relevant Humidity: 5-90% (non-condensing) Storage Temperature: -40 to 85 C Relevant Humidity: 5-95% (non-condensing) Page 6/10 2021/7/28 WARNINGS FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. ISED Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

1.This device may not cause interference. 2.This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

Page 7/10 2021/7/28 1.Lappareil ne doit pas produire de brouillage;

2.Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. ISED Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20cm de distance entre la source de rayonnement et votre corps. The transmitter module may not be co-located with any other transmitter or antenna. Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Pour les produits disponibles aux tats-Unis / Canada du march, seul le canal 1 11 peuvent tre exploits. Slection d'autres canaux n'est pas possible. This module is intended for OEM integrators under the following conditions:

1. Ensure that the end-user has no manual instructions to remove or install module. 2.This module is certified pursuant to Part 15 rules section 15.247 and RSS-247. 3.This module has been approved to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna Frequency Band Antenna Type Brand 1 2400-2483.5MHz Printed Antenna LITEON Model Number WN3602M Gain(dBi)

-0.9 4.Label and compliance information Label of the end product:

FCC The host product must be labeled in a visible area with the following " Contains FCC ID:

2AIBX-NIULL". The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ISED This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains transmitter module IC: 21700-NIULL or Page 8/10 2021/7/28 Contains IC: 21700-NIULL Contient le module d'mission IC: 21700-NIULL 5.Information on test modes and additional testing requirements This module has been approved under stand-alone configuration. OEM integrator has be limited the operation channels in channel 1-11 for 2.4GHz band. The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093/RSS-102 and different antenna configurations The information on how to configure test modes for host product evaluation for different operational conditions for a stand-alone modular transmitter in a host, versus with multiple, simultaneously transmitting modules or other transmitters in a host can be found at KDB Publication 996369 D04. OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC/ISED authorization is no longer considered valid and the FCC/IC No. cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC/ISED authorization. 6.Additional testing, Part 15 Subpart B and ICES-003 disclaimer Appropriate measurements (e.g. Part 15 Subpart B compliance) and if applicable additional equipment authorizations (e.g. SDoC) of the host product to be addressed by the integrator/manufacturer. This module is only FCC/ISED authorized for the specific rule parts 15.247, RSS-247 listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC/ISED rules that apply to the host product as being Part 15 Subpart B/ICES-003 compliant. 7.The user manual of the end product should include:

FCC:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter. Page 9/10 2021/7/28 ISED:

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

1.This device may not cause interference. 2.This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1.Lappareil ne doit pas produire de brouillage;

2.Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. ISED Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20cm de distance entre la source de rayonnement et votre corps. The transmitter module may not be co-located with any other transmitter or antenna. Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Pour les produits disponibles aux tats-Unis / Canada du march, seul le canal 1 11 peuvent tre exploits. Slection d'autres canaux n'est pas possible. Page 10/10 2021/7/28

Confidentiality Request Letter

Date: July 30, 2021

Pursuant to Public Notice DA 04-1705, and in order to comply with the marketing regulations in 47

C.F.R. §2.803 and the importation rules in 47 C.F.R. §2.1204 while ensuring that business-sensitive

information remains confidential until the actual marketing of newly authorized devices, we are request

the Commission grant temporary confidential treatment and not release the following attachments for

routine public disclosure until 180 days after the grant date.

Federal Communications Commission

Authorization and Evaluation Division

Subject: Request for confidentiality

FCC ID: 2AIBX-NIULL

To whom it may concern:

Short-term Confidentiality

1.

Internal Photographs

2. External Photographs

3. User’s manual

4. Test Set up photos

Permanent Confidentiality

document from public disclosure indefinitely.

1. Block Diagram

2. Schematics

3. Operational Description

Pursuant to the provisions of Sections 0.457 and 0.459 of Commission’s rules (47CFR§§0.457,

0.459), we are requesting the Commission to withhold the following attachment(s) as confidential

It is our understanding that test measurement reports and correspondence during the certification

review process cannot be granted confidential treatment, and such information will be available for

public review once the grant of equipment authorization is issued.

Sincerely,

Applicant

Address

Signature

E-mail

Tel.

: ELECTROLUX ITALIA S.p.A.

: Corso Lino Zanussi 24, Porcia 33080, Italy

:

_________________________________

Name and Job Title.

: Massimiliano Ranieri, Managing Director

: massimiliano.ranieri@electrolux.com

: +39 0434 3961

Classified as Internal

Firmato digitalmente da:Ranieri MassimilianoIngegnereFirmato il 30/07/2021 15:27Seriale Certificato: 95170001573975370679205112436654185229Valido dal 11/12/2020 al 11/12/2025ArubaPEC S.p.A. NG CA 3

Single Modular Approval Request Letter Date: August 27, 2021 Subject: Single Modular Approval Attestation FCC ID: 2AIBX-NIULL Dear Reviewer, We, Sporton International Inc., are authorized by Electrolux Italia S.p.A., to have the NIUL approved under single modular approval authorization. The requirements regulated in 47 CFR 15.212 have been fulfilled and clearly explained below. 1. The requirement of RF shielding: The shielding of the radio portion can be demonstrated 2. The requirement of buffered inputs: Buffered data inputs stage has been integrated in chip 3. The requirement of power supply regulation: The part number of the power regulator is in exhibition External Photo. NXP 88MW320. NXP 88MW320. 4. The requirements of section 15.203 and 15.204(C): The requirements of antenna connector and spurious emission have been fulfilled. Please reference the exhibition Test Report. Sample. 5. The requirement of stand-alone test configuration: Please reference exhibition Test Configuration Photo for the stand-alone test configuration. 6. The requirement of labeling: The instruction on the labeling rule of the end product has been stated in the user manual of this module. Please also see the exhibition Label 7. The requirement of compliance on specific rule or operating requirements: The required FCC rule has been fulfilled and all the instructions for maintaining compliance has been 8. The requirement of RF exposure: Please refer exhibition RF Exposure for the compliance clearly stated in the Users Manual. of RF exposure rule. Please do not hesitate to contact me for any questions of this request letter. Thank you. Signature

Name E-mail

: Leo Huang

: leohuang@sporton.com.tw

Power of Attorney

Date: July 30, 2021

Federal Communications Commission

Authorization and Evaluation Division

7435 Oakland Mills Rd

Columbia MD 21046-1609

FCC ID: 2AIBX-NIULL

Product Name: NIUL

To whom it may concern:

Subject: Product Certification Representative Authorization Letter

We the undersigned, hereby authorize following person to act as our agent in the preparation

of an application for equipment authorization to the FCC Rules and Regulations.

Sporton International Inc.

Address

: No.52, Huaya 1st Rd., Guishan Dist., Taoyuan City 333, Taiwan

Name

: Leo Huang

Job Title : Manager

e-mail

: Leohuang@sporton.com.tw

We further certify that neither the applicant nor any party to this application, as defined in 47

CFR Ch. 1.2002(b), is subject to a denial to Federal benefits, that include FCC benefits,

pursuant to section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. § 862.

This appointment also includes the authority to complete FCC Form 731 on our behalf and

sign the application as an authorized agent.

: ELECTROLUX ITALIA S.p.A.

: Corso Lino Zanussi 24, Porcia 33080, Italy

Applicant

Address

Signature

E-mail

Tel.

:

: +39 0434 3961

Name and Job Title.

: Massimiliano Ranieri, Managing Director

_________________________________

: massimiliano.ranieri@electrolux.com

Classified as Internal

Firmato digitalmente da:Ranieri MassimilianoIngegnereFirmato il 30/07/2021 15:25Seriale Certificato: 95170001573975370679205112436654185229Valido dal 11/12/2020 al 11/12/2025ArubaPEC S.p.A. NG CA 3