Wi-Fi Extender KWM2000
(included with KS1000) The KING WiFiMax creates your own private and secure Wi-Fi network, just like you have in your home. When in range of an available network, simply configure your WiFiMax to connect to that network, and it will extend the internet access from that network to your own private Wi-Fi network. SWIFT Omnidirectional Wi-Fi Antenna KS1000
(not included with KWM2000) The KING Swift is an omnidirectional Wi-Fi antenna that increases the range and performance of your KING WiFiMax router and range extender. This 2.4GHz Wi-Fi antenna mounts to your roof, connects to your KING WiFiMax via a single cable, and allows your KING WiFiMax to connect to networks from even farther away and still utilize its 5GHz network for fastest speeds. CONTENTS CONTENTS ................................................................................................. 2 CONNECTIONS .......................................................................................... 3 FIRST-TIME USE ..................................................................................... 4-7 STANDARD OPERATION ..................................................................... 8-11 INSTALLATION ................................................................................... 12-13 TROUBLESHOOTING .............................................................................. 14 SPECIFICATIONS .................................................................................... 15 LIMITED WARRANTY ......................................................................... 16-17 WIRELESS REGULATORY INFORMATION ....................................... 18-19 Page 1 CONTENTS KING WiFiMax KWM2000 For increased performance, you can add a KING Swift
(contact KING Customer Service at 952-345-8147). KING WiFiMax Manual Power Supply NOTE: No tools are required to set up and use the KING WiFiMax (unless wall mounting the unit). There are key hole slots on the back to mount the unit to a wall. The user must determine where and how to best mount the unit to a wall
(inside use only). KING Swift KS1000 Includes the KING WiFiMax and power supply shown above. KING Swift antenna with preattached cable Pole, ladder or mirror-mount bracket Roof-mount bracket White wall plate Black wall plate Watertight connector Washer Nut Cable NOTE: The KING Swift, bracket and hardware may come preassembled. For complete installation instructions see page 10. Page 2 CONNECTIONS Place your KING WiFiMax on a stable surface (or wall mount). Make connections as shown. (Blue lights on KING WiFiMax will turn on when power is connected.) A B C Attach included dipole antenna or cable from KING Swift to open port. Rotate antennas so they point up. Connect to power. NOTE: You can use the keyhole slots on the back to wall mount the unit. ANTENNAS MUST ALWAYS POINT UP. Page 3 FIRST-TIME USE NOTE: If you have already completed this first-time use section, go to page 8. TIP When using a smart phone or tablet: to maintain the best connection to your KING WiFiMax, it is suggested that the smart phone or tablets cellular network be turned off while completing the first-time use section. Back to Settings WiFi ON Choose a Network... 1. Go to your smart phone, tablet or computers Wi-Fi settings page and connect to the KING 5G network:
KING_XXXXXX_5G KING_XXXXXX_5G KING_XXXXXX Fun Lake Campground Dads Campground TIP XXXXXX is a number/letter combination unique to your router and can be found on the bottom of your router in the SSID row. Chat Cafe Campit Here Graphics will vary. KC1074 If you do not see KING_XXXXXX_5G (5GHz network), connect to KING_XXXXXX
(2.4GHz network). Always choose the 5G network if possible, as it is faster than the 2.4GHz network. Page 4 2. Open your devices web browser. Go to: http://mykingwifi.com Tap WiFi Settings in the left-hand column. Type exactly as written. Internet Status Internet Settings WiFi Settings Parental Control VPN Advanced Settings System Settings Internet Status English Exit 2.4 GHz: King_XXXXXX 5 GHz: King_XXXXXX_5G Repeating failed. Upstream Router My Router Online: 1 WiFi Extender KC1095
Current Speed WAN IP Address V15.03.05.16_multi Firmware Version 3. Tap WiFi Name & Password. WiFi Settings English Exit Internet Status Internet Settings WiFi Settings Parental Control VPN Advanced Settings System Settings WiFi Name & Password Enable Wireless Repeating Enable Channel & Bandwidth Channel/Bandwidth Transmit Power 2.4 GHz High/5 GHz High Beamforming+
Enable AP Mode Disable Anti-interference Auto KC1096 Page 5 4. In the screen below, you MUST change your Wi-Fi name and password to personalize it and keep it secure. Do steps A and B for both the 2.4 GHz and 5GHz networks (you will only have to do this once). A Enter a new Wi-Fi name. When entering your new names, make sure to completely erase the existing names in the boxes. TIP Add _5G after your 5GHz network name to differentiate it from your 2.4GHz network name. B Enter a password. KING highly recommends password protecting your name. Choose WPA/WPA2-PSK under Encryption Mode to enable password protection. TIP Passwords can be the same for both networks if you wish, and must be at least 8 characters. Enter names and passwords for both networks. WiFi Settings Internet Status WiFi Name & Password Internet Settings WiFi Settings Parental Control VPN Advanced Settings System Settings 2.4 GHz Network A WiFi Name & Password Enable Wireless Repeating WiFi Name:
Enable Enter name here Channel & Bandwidth Channel/Bandwidth Encryption Mode:
WPA/WPA2-PSK B Beamforming+
Enable WiFi Password:
AP Mode Disable Enter password here Anti-interference Auto 5 GHz Network A WiFi Name:
Enter name here_5G Encryption Mode:
WPA/WPA2-PSK B WiFi Password:
Enter password here KC1097 Page 6 English Exit X Transmit Power 2.4 GHz High/5 GHz High Hide Choose this encryption mode to enable password protection. Hide 2.4GHZ Write your network name here:
Write your password here:
5GHZ Write your network name here:
Write your password here:
5. When you have entered names and passwords for both networks, tap Save. WiFi Settings Internet Status WiFi Name & Password English Exit X Internet Settings WiFi Settings Parental Control VPN Advanced Settings System Settings KC1144 Encryption Mode:
WPA/WPA2-PSK WiFi Name & Password Enable Wireless Repeating WiFi Password:
Enable Channel & Bandwidth Enter password here Channel/Bandwidth Transmit Power 2.4 GHz High/5 GHz High 5 GHz Network Beamforming+
Enable AP Mode WiFi Name:
Disable Anti-interference Enter name here_5G Auto Hide Encryption Mode:
WPA/WPA2-PSK WiFi Password:
Enter password here Save TIP If the Save button does not appear, scroll down to find it. You have personalized your router setup. Continue on next page. TIP If you turned off your cellular network during first-time use, it is now safe to turn it back on. Page 7 STANDARD OPERATION TIP When using a smart phone or tablet: to maintain the best connection to your KING WiFiMax, it is suggested that the smart phone or tablets cellular network be turned off during standard operation. 1. Go to your phone, tablet or computers settings page and connect to the Wi-Fi Network with your personalized network name (you created this on page 6). The example shown is MyWiFiName_5G. If your device cannot connect to your 5G network, connect to your other network. TIP For best performance, choose the 5GHz network whenever possible. Back to Settings WiFi ON Choose a Network... MyWiFiName_5G MyWiFiName Fun Lake Campground Dads Campground Chat Cafe Campit Here KC1075 2. Open your devices web browser. Go to: http://mykingwifi.com Type exactly as written. Tap WiFi Settings in the left-hand column. Internet Status Internet Settings WiFi Settings Parental Control VPN Advanced Settings System Settings Internet Status 2.4GHz: MyWiFiName 5GHz: MyWiFiName_5G 2.4 GHz: King_XXXXXX 5 GHz: King_XXXXXX_5G English Exit Repeating failed. Upstream Router My Router Online: 1 WiFi Extender
Current Speed WAN IP Address V15.03.05.16_multi Firmware Version KC1095 Page 8 3. Tap Wireless Repeating. WiFi Settings English Exit WiFi Name & Password Enable Wireless Repeating Enable Channel & Bandwidth Channel/Bandwidth Transmit Power 2.4 GHz High/5 GHz High Beamforming+
Enable AP Mode Disable Anti-interference Auto Internet Status Internet Settings WiFi Settings Parental Control VPN Advanced Settings System Settings KC1096 4. Tap the blue arrows to scan for networks. WiFi Settings Internet Status Wireless Repeating English Exit X Internet Settings WiFi Settings Parental Control VPN Advanced Settings System Settings KC1115 WiFi Name & Password Enable Wireless Repeating:
Wireless Repeating Enable Channel & Bandwidth Channel/Bandwidth Transmit Power 2.4 GHz High/5 GHz High Repeating Mode:
WISP Client+AP Upstream WiFi Name:
Fun Lake Campground Beamforming+
Enable Upstream WiFi Password:
AP Mode Disable Select your network Anti-interference Auto Save Page 9 The router is scanning for networks. WiFi Settings Internet Status Wireless Repeating English Exit X Wireless Repeating:
WiFi Name & Password Enable Repeating Mode:
Wireless Repeating Enable WISP Channel & Bandwidth Channel/Bandwidth Client+AP Transmit Power 2.4 GHz High/5 GHz High Upstream WiFi Name:
Scanning... Beamforming+
Enable AP Mode Disable Save Anti-interference Auto Internet Settings WiFi Settings Parental Control VPN Advanced Settings System Settings KC1112 5. After the scanning process is complete, this screen will appear. Tap on Upstream WiFi Name drop down menu to display a list of available networks. WiFi Settings Internet Status Wireless Repeating English Exit X Wireless Repeating:
WiFi Name & Password Enable Wireless Repeating Enable Repeating Mode:
WISP Channel & Bandwidth Channel/Bandwidth Client+AP Transmit Power 2.4 GHz High/5 GHz High Upstream WiFi Name:
--Select--
Internet Settings WiFi Settings Parental Control VPN Advanced Settings System Settings Beamforming+
Enable TIP If the upstream network you are looking for does not appear in this list, scroll up and down within the box to find it. KC1099
--Select--
AP Mode Disable
--Enter WiFi name manually--
Anti-interference Fun Lake Campground Auto Dads Campground Chat Cafe Campit Here Joes Cafe Inter-fun Page 10 6. Select the network you would like to extend (not your customized router name) and input the password if necessary (not pictured). Tap Save. 7. This popup should appear. Tap OK. Wireless Repeating:
Repeating Mode:
WISP Client+AP Upstream WiFi Name:
The router must reboot to activate your setting. Do KING Falcon 2 you want to reboot the router?
Upstream WiFi Password:
Cancel OK KC1114 Save 8. Your KING WiFiMax will reboot. If your router gets stuck at 100% and wont finish rebooting, or if your Wi-Fi device does not have internet access, you may need to go back to your smart phone or tablets settings page and ensure that it reconnected to the Wi-Fi network with your personalized network name, as you may lose connection during the routers rebooting process. Rebooting... Please wait 100%
KC1130 KC1113 Your KING WiFiMax is now extending your network!
If you turned off your cellular network during standard operation, it is now safe to turn it back on. TIP Page 11 INSTALLATION For best performance, the antenna should be located as far away as possible from other rooftop objects (TV antennas, AC units, etc.) and with the best all around line of sight. When determining locations, make sure the long cable will reach the KING WiFiMax when attached to the KING Swift cable. (KING Swift cable may go directly to prewire enclosure - see opposite page). Do not locate the KING WiFiMax or KING Swift in a slide-out. Cable connection between KING Swift and long cable must always be inside vehicle
(or prewire enclosure if using). 1. Drill 5/16 hole in roof where cable will enter roof. Feed long cable into position with enough cable sticking out of roof to attach KING Swift cable. This end is marked ROOF and is red. 2. Connect KING Swift cable and long cable. 3. Apply roof-compatible sealant around perimeter of bracket. Feed cable into hole, lower bracket into position and fasten to roof. Seal fastener heads and cable hole in roof. 4. Inside vehicle, install wall plate if desired, and connect cable to KING WiFiMax. You can also use the included bracket to mount the antenna to a pole, ladder or mirror. Page 12 IMPORTANT!
The installer is responsible for determining and supplying the most appropriate fasteners to secure the bracket to the roof. All holes, fastener heads, and the entire perimeter of the bracket must be completely sealed and weatherproofed with roof-compatible sealant. If there is a prewire enclosure on the roof, you will find a preinstalled wall plate in the vehicle. Remove this wall plate and install the included black or white wall plate. Page 13 TROUBLESHOOTING The KING WiFiMax doesnt power on (no blue lights on front). Make sure power supply plug is securely inserted into back of KING WiFiMax. Make sure the power supply is plugged into a known good power outlet. I cant find the network KING_XXXXXX_5G or KING_XXXXXX. Make sure your KING WiFiMax is plugged in. It may take up to a minute for these networks to appear. Some older devices may be unable to see the 5GHz network. This is completely okay; just use the KING_XXXXXX network. I cant connect to mykingwifi.com Make sure you are connected to your KING WiFiMaxs network. Then make sure you type in the web address exactly as it appears in this manual: http://mykingwifi.com. I cant enter a password in the designated box. Choose WPA/WPA2-PSK under Encryption Mode (right above the password box) to enable password protection. I dont see the Upstream WiFi name I want to extend in my list of networks. If a network is very far away or very weak, the KING WiFiMax may not be able to see it, or may not offer it as an option. Try scanning again for networks by clicking on the blue circular arrows. If your network is still not offered as an option, try moving your KING WiFiMax to a location closer to your desired network. When my router reboots, it gets stuck at 100% and wont finish rebooting. Try reloading the page. If the page wont load, make sure your device is still connected to the KING WiFiMax. It may have disconnected during the reboot. The KING WiFiMax doesnt seem to extend the range of my Wi-Fi, or has trouble picking up signal from my source. Make sure all 4 antennas (3 if KING Swift is connected) are pointing up. If wall mounting, antennas must be rotated to point up as well. Certain types of obstructions (other vehicles, buildings, or large amounts of metal) can reduce signal levels. Try relocating the KING WiFiMax. NOTE: KING WiFiMax can be reset by pressing and holding the reset button until the front lights go out (15-20 seconds). Back of KING WiFiMax POWER WIFI RST/WPS KC1244 Let us help! KING Customer Service 952-345-8147 Page 14 KING WiFiMax Power:
SPECIFICATIONS Included 12v power supply, requiring 110V AC plug-in Wireless standards:
IEEE802.11a/b/g/n/ac Supported Frequencies:
2.4GHz and 5.8GHz (dual-band) Security:
WPA/WPA2-PSK Storage Environment:
Temperature -40F to 158F KING Swift Radio Frequency Band:
2.4GHz Wireless Standards:
IEEE802.11a/b/g/n Antenna:
Height:
Diameter:
Weight:
3dBi roof-mounted omnidirectional antenna 9.5 0.75 0.25LBS Page 15 LIMITED WARRANTY Each new KING WiFiMax and King Swift is thoroughly inspected and tested before leaving the factory, and is covered by the following limited warranty from the date of original purchase:
One-year parts warranty: The customer is not responsible for the cost of replacement parts if the original part is determined to be defective under the terms of the warranty. The customer is responsible for the cost of replacement parts after one year. Only KING and certified dealers may perform warranty evaluations and repairs. Depending upon the problem, KING may authorize a dealer to perform the necessary repairs. Any warranty labor outside of that performed at the factory is not covered unless 1) the product has been installed by an authorized dealer/installer or OEM manufacturer and 2) the dealer/installer receives prior authorization to perform the repair. A certified dealer must not perform any repair without first contacting KING for a Service Order Number. KING will advise the dealer on how to proceed with any repairs. Should any trouble develop during the warranty period, contact KING at (952) 345-8147. You must contact KING before the warranty period expires. The customer must supply proof of purchase (such as a dated sales receipt) when requesting warranty service. If the customer cannot supply proof of purchase, warranty period shall start 30 days after date of manufacture. If it is determined that the unit needs to be returned to KING, customer must return COMPLETE product, freight prepaid, to:
KING, 11200 Hampshire Avenue South, Bloomington, MN 55438-2453. If inspection shows the trouble is caused by defective workmanship or material, KING will repair (or at its option, replace) without charge. When returning product, KING will supply an RMA number (Return Merchandise Authorization). This number must be clearly written on the box. Failure to clearly write RMA number on box will result in delays in processing claim. Along with product, the customer should include in the box: his/her name, address, daytime phone number, proof of purchase and description of the problem. This warranty does not cover installation and external wiring, or remanufactured units. This warranty does not cover damage caused by the use of an accessory other than a KING accessory designed for the product. This warranty is not transferable from the original owner. KING cannot be held responsible for changes in the expanding and changing digital and analog communications market that cause the product to no longer operate correctly. Page 16 This warranty also does not apply where:
The product has been abused, misused, improperly installed or improperly maintained. The product has been used with an accessory other than a KING accessory designed for the product. Repairs have been made or attempted by others that are not certified by KING to do such repairs. Repairs are required because of normal wear and tear. Alterations have been made to the product. The product or any associated component has been opened without authorization or disassembled to any degree. Damage has been caused by power washing. Circumstances beyond the control of KING cause the product to no longer operate correctly. Customer is not the original owner. In no event shall KING be liable for any indirect, incidental, or consequential damages from the sale or use of the product. This disclaimer applies both during and after the term of this warranty. KING disclaims liability for any implied warranties, including implied warranties of merchantability and fitness for a specific purpose, after the term of this warranty. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Page 17 WIRELESS REGULATORY INFORMATION FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equip-
ment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IEEE 802.11b or 802.11g operation of this product in the USA is firmware-limited to channels 1 through 11. The device for the band 5150-5250 MHz is only for indoor usage to reduce the potential for harmful interference to co-channel mobile satellite systems. Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. Innovation, Science and Economic Development Canada Statement CAN ICES-3 (B)/NMB-3(B) This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. For product available in the USA/Canada market, only channel 1-11 can be operated. Selection of other channels is not possible. The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology. Innovation, Science and Economic Development Canada Radiation Exposure Statement This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with ISED multi-transmitter product procedures. Restrictions in the 5 GHz Band The device for the band 5150-5250 MHz is only for indoor usage to reduce the potential for harmful interference to co-channel mobile satellite systems. The maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate. Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. This radio transmitter has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Detachable antenna:
5 dBi at 2.4 GHz, 50, Dipole Additional requirements for the band 5600-5650 MHz Until further notice, devices subject to this Section shall not be capable of transmitting in the band 5600-5650 MHz, so that Environment Canada weather radars operating in this band are protected. Page 18 Avis dInnovation, Sciences et Dveloppement conomique Canada CAN ICES-3 (B)/NMB-3(B) Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) Lappareil ne doit pas produire de brouillage; et (2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Pour les produits disponibles sur le march aux tats-Unis et au Canada, seuls les canaux de 1 11 peuvent tre utiliss. La slection dautres canaux nest pas possible. Le dispositif peut automatiquement cesser dmettre en cas dabsence dinformations transmettre, ou cause dune dfaillance technique. Notez que lobjet nest pas dinterdire la transmission des informations de contrle ou de signalisation ou lutilisation de codes rptitifs lorsque requis par la technologie. Avis dInnovation, Sciences et Dveloppement conomique Canada concernant lexposition aux radiofrquences Ce matriel est conforme aux limites tablies par ISED en matire dexposition aux radiofrquences dans un environnement non contrl. Ce matriel doit tre install et utilis une distance dau moins 20 cm entre lantenne et le corps de lutilisateur. Cet appareil et son (ses) antenne(s) ne doivent pas tre situs proximit ou fonctionner en association avec une autre antenne ou un autre met-
teur autre quen respectant les procdures d ISED relatives au fonctionnement des dispositifs multi-metteurs. Restrictions dans la bande 5 GHz Lappareil pour la bande de 5150 5250 MHz est conu pour usage lintrieur seulement afin de rduire le potentiel dinterfrences pour les systmes mobiles par satellite qui utilisent le mme canal. Le gain maximal dantenne permis (pour les dispositifs utilisant la bande 5725-5825 MHz doit se conformer la limite de p.i.r.e. spcifie pour lexploitation point point et non point point, selon le cas. De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Le prsent metteur radio a t approuv par Innovation, Sciences et Dveloppement conomique Canada pour fonctionner avec les types dantenne numrs ci-dessous et ayant un gain admissible maximal. Les types dantenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu pour tout type figurant sur la liste, sont strictement interdits pour lexploitation de lmetteur. Antenne dtachable:
5 dBi 2.4 GHz, 50, Diple Prescriptions supplmentaires pour la bande 5600-5650 MHz Jusqu nouvel ordre, les appareils faisant lobjet de la prsente section ne doivent pas transmettre dans la bande 5600-5650 MHz, afin que les radars mtorologiques dEnvironnement Canada fonctionnant dans cette bande soient protgs. Page 19 Simply better, by design. 11200 Hampshire Avenue South, Bloomington, MN 55438 PH 952.922.6889 || FAX 952.922.8424 || kingconnect.com 2021 KING 23854 Rev 01 All trademarks are the sole property of their respective owners.