FCC ID: 2BC2J-ZBAA409ECS Charging Point

AC Charging pile User's Manual Welcome Thank you for choosing Easy Charging AC Charging Station . This EV charger supports smart charging with a smart control APP, via optional WIFI or blue-

tooth, includes remote start / stop, reservation, set output current, monitor charging status etc. Please use your SMART phone scan the following QR code to download the latest APP. APP The information provided in this documentation contains general descriptions and/or technical characteristics of the performance of the products contained herein. This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications. It is the duty of any such user or integrator to perform the appropriate and complete risk analysis, evaluation and testing of the products with respect to the relevant specific application or use thereof. Neither Easy China nor any of its affiliates or subsidiarEasy shall be responsible or liable for misuse of the information contained herein. If you have any suggestions for improvements or amendments or have found errors in this publication, please notify us. You agree not to reproduce, other than for your own personal, noncommercial use, all or part of this document on any medium whatsoever without permission of Easy Charging , given in writing. You also agree not to establish any hypertext links to this document or its content. Easy China does not grant any right or license for the personal and noncommercial use of the document or its content, except for a non-exclusive license to consult it on an as is basis, at your own risk. All other rights are reserved. All pertinent state, regional, and local safety regulations must be observed when installing and using this product. For reasons of safety and to help ensure compliance with documented system data, only the manufacturer should perform repairs to components. When devices are used for applications with technical safety requirements, the relevant instructions must be followed. Failure to use Easy Charging software or approved software with our hardware products may result in injury, harm, or improper operating results. Failure to observe this information can result in injury or equipment damage. Safety Information Easy Charging Co., Ltd. All rights reserved. Page 1 Safety Information Before using or maintaining this product, it is important to read the following safety instructions. Failure to follow and implement all the specified instructions and procedures, will invalidate the warranty and as such Easy Charging will not be liable for any .claims. Do not open the charger. Do not use the charger if it is damaged. Do not use an extension lead on the charging cable. Do not touch or insert foreign objects into the plugs. Do not install the charger near flammable, explosive, or combustible materials. All work on the equipment must only be carried out by qualified personnel who have read and fully understood all safety information and installation requirements contained in this manual. The charger must be out of reach from children. EV charger must be connected to a protective earth conductor. The electrical installation must comply with all local applicable safety requirements, standards and guidelines. No modifications must be made to the EV charger. Components should not be changed or replaced by the end-user or unqualified personnel. Page 2 1. Product Overview AC Charging Pile developed by Easy Charging Co., Ltd., creates smart, stable and reliable charging experience for electric vehicles owners. LED Charging indicator Emergency Stop Button Display screen Coupler Holder 1.1 Main features of products LED Charging indicator: Blue Standby; Green (flashing) charging in progress; Red Error. Display screen: displays the status and parameters of charging station. Emergency stop button: Press down this button in case of emergency. Coupler holder: place the charging coupler head to the coupler holder when the charge station is not in use. Page 3 2. List of Accessor Instruction Manual *1 Certificate *1 Mounting plate *1 Wire clamp plate *1 Anchor bolt *5 Flat head cross tapping screws M4*1in *5 3.Main Technical Parameters Round head self-

tapping teeth screws M3*0.3in *2 Mechani cal teeth pan head screws with flat tail M4*0.4in*3 Product model Product name Case Material Product size Wire-in Net weight Cable length Input voltage Input frequenc y Rated power Output voltage Output current Standby power consumption Working temperature Storage temperature Working altitude Ingress Protection Cooling mode ZAA411C-CS 11.5KW AC Charging Pile PC+ Fireproof and Flame Retardant W8.7*D4*H16 inch Bottom feed 20 pounds 23. feet AC 100V-240V20%

603Hz 11.5KW AC 240V20%

48A (max) 5W

-20+50

-40+80

<1.2mile TYPE 3R natural cooling Page 4 Safety standard Warranty period Special protection UL 2231,UL 2594 2 Years UV protection design Emergency shutdown, OVP , UVP, OCP, Leakage protection, Earthing reminder, temperature protection, waterproof protection, power-off protection, data protection. Insulation resistance: the insulation resistance between input loop and ground, output loop and input to output of charging station is 10M. 4. Installation Instructions All work on the equipment must only be carried out by qualified personnel who have read and fully understood all safety information and installation requirements contained in this manual. 4.1 Installation environment requirements 4.1.1 This AC smart charging stations are suit for outdoor application with its TYPE 3R structure. 4.1.2 Please ensure that the Usage temperature is in the range of -20 to

+50. Do not mount the EV charger in areas containing highly flammable materials or gases. Do not mount the EV charger in potentially explosive atmospheres. 4.2 Before Installation 4.2.1 Easy intelligent AC Charging Pile can be installed on the wall or bracket according to the requirements. the charger. 4.2.2 Make sure appropriate MCB is installed at upstream of AC power supply to 4.2.3 Use protection. The selected circuit protection device must integrate the load appropriate residual current device (RCD) and the corresponding electrical overcurrent protection device. 4.2.4 Use copper cables that comply with local wiring regulations. The selected cable must be able to withstand a continuous load of up to 50A for each period. Page 5 4.3 Wall mounting 4.3.1 Remove 10 x M3x0.3inch screws on the back cover, connect AC power supply cord to the corresponding terminals labeled L, N and PE. Tighten cable gland and assemble the back cover, tighten 10 x M3x0.3inch screws. Connect with AC power cord 4.3.2 Use the mounting plate as template to position the holes on the wall, drill three 0.1inch holes at depth of 1.1 inch. Fix the mounting plate on the wall with 3 x M4 x 0.8inch screws. 4.3.3 Fix the charger on mounting plate with 3 x M4 x 0.4 inch screws. Page 6 4.3.4 The final effect picture after fixing the charging pile. Page 7 5 Smart Phone APP User Guide with optional WIFI/Bluetooth module 5.1 Please use your smart phone to scan the following QR code to obtain the APP user Guide. APP user Guide Page 8 6 Charger User Guide 6.1 The LCD Displays ICONS Function. Reservation indicator Charging duration indicator Time window Paramet er window WIFI icon Bluetooth Smart charging indicator Error icon Connector status indication Charging status indication 6.1.2 WIFI icon: The icon lights up after successful connection with the WIFI router. 6.1.3 Bluetooth icon: The Bluetooth icon lights up after successful connection with Bluetooth remote control or smart phone. 6.1.4 Charging duration indicator: the icon lights up when charging in progress, and the main time window displays the charging duration (hours: minutes). 6.1.5 Reservation indicator: lights up when the charger is set to reservation charge mode via APP. 6.1.6 Smart charging indicator: When the APP has set smart charging, the icon lights up. The system will automatically adjust the charging power according to the time set by the user. 6.1.7 Error icon: when the equipment is fault, the icon lights up and the error code is displayed in the time window. 6.1.8 Time window: display charging time parameters or error code. 6.1.9Parameter window: displays the charging voltage, current, power, and the temperature in the charging station. Page 9 6.1.10 Connector status indication: the icon flashes when it is not connected to the EV, and the icon is always on when it is connected to EV. 6.1.11 Charging status indication: 3 icons are always on when charging is not in progress, and the flashing light indicates charging in progress. 6.2Charging station operation sequence 6.2.1 Ensure the Emergency Stop Button is released. 6.2.2 Power-on the charger, wait until the self-test is completed. The LED indicator turns blue when charger is standby. 6.2.3 Plug the charging gun into the car 6.2.4 With the default plug-and-charge setting, the car will charge itself and the LED will turn green (blink). 6.2.5 After the charging is completed, the LED light will turn blue, unplug the charging gun from the electric vehicle, and insert it back into the fixed base of the charging pile.. You may end the charging session from your EV (interface varEasy from different EV models);

Or use smart phone APP or Bluetooth remote controller to stop the charging session (when optional WIFI/Bluetooth module is supplied);

Or swipe RFID card to stop charging session (when RFID module is supplied). 6.2.6 In case of abnormal situation during charging, press the emergency stop switch immediately, Attention:

Don't unplug the EV Charger before the charging is completed, theres risk of electric shock. 7 Error Code error code E01 E02 E03 E04 E05 E06 E07 E08 E10 E11 E12 Fault description Grounding fault leakage current protection Input overvoltage Input undervoltage overcurrent protection Charging coupler abnormal. Emergency Stop Button is pressed down Coupler locking mechanism abnormal Temperature sensor 1 faultreserve Temperature sensor 2 fault Temperature sensor 3 failed. Page 10 E13 E14 E20 E21 E22 E23 E30 E31 Charging area ventilation error Leakage protector calibration failed Relay open circuit Relay adhesion Relay overtemperature reserve EEPROM MCB communication failure 8 Warranty Your Easy Charging AC Charging Pile has the benefit of our guarantee, which covers the cost of repairs for 24 months from the date of installation or 27 months from the date of shipment, depending on which comes first. This gives you the reassurance that if, within that time, your charger is proven to be defective because of workmanship or material defect we will, at our discretion, either repair or replace the charger at no cost to you. Warranty Limitations:

The Warranty is valid only for products purchased either directly from Easy Charging or from an authorized reseller of Easy Charging Co., Ltd. 1) Any defect or damage which is a result of repair, alteration, or modification performed without the written permission of Easy Charging ;

2) The use of parts not manufactured, sold or approved by Easy Charging in any replacement or repair;

3) Cases where the Easy Charging Product is operated on an electrical supply which is not in accordance with the ratings specified in writing by Easy Charging Co., Ltd.;

4) The Easy Charging Product is damaged as a result of incorrect installation or being used for a purpose for which it is not designed, sold or otherwise not in accordance with any written specified instructions for use or Easy Charging Product installation performed by third party Easy Charging not approved by CUSTOMER or Easy Charging Co., Ltd.;

If changes occur in the condition or operational quality of the Easy Charging Product due to incorrect storage, transportation, mounting, climate or any other influence outside the control of Easy Charging Co., Ltd.;

6) The Easy Charging Product is further damaged as a result of operating the 5) product when it was known to be defective;

7) Easy Charging Product parts requiring replacement due to normal wear and tear including the replacement of the following parts: cables, couplers, and user interface;

8) When Easy Charging Product damage is caused directly or indirectly by utility supply problems, insect or animal attacks, lack of user care, vandalism, incorrect power supply, electrical storm damage, flooding or any other weather phenomena. Page 11 9) Unauthorized operation or modification of the Easy Charging Product or any disregard of the instructions contained in the User manual;

10) Any loss, damage, or destruction to the Easy Charging Product due to an event of force majeure that is an act of nature; and/or. 11) Any loss, damage or destruction to the Easy ChargingProduct arising from, or caused or contributed to by, the Customers or End-Users negligence or the negligence of the Customers agents or servants. 12) The firmware changes due to the modifications asked by the customer or changes in standards. 9 Recycling and Disposal 1) Disposal must be according to national and regional Regulations for electrical and 2) electronic equipment respectively. If the equipment is damaged, the old equipment and batteries must not be disposed of with household waste or large garbage.. 3) Dispose of the packaging material in the region's usual collection container for cardboard, paper, and plastics. Page 12 FCC Caution. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

FCC Label Charging Point Model name: ZBAA409E-CS FCC ID: 2BC2J-ZBAA409ECS L:30mm Note: The label is silk-screen on the sample

Date2023.10.19 Electronic Way Technology Co., Ltd Product Model Number: ZBAA409E-CS, ZBAA102E-CS, ZBAA407E-CS, ZBAA403E-CS FCC ID2BC2J-ZBAA409ECS To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following:

Testing Approval applications and procedures We declare that ORGANIZATION. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by ORGANIZATION.on our behalf shall have the same effect as acts of our own. By: peter cheng Contact Listed on FCC Wesbite Title: manager Email: sales05@mtl-test.com On behalf of: Electronic Way Technology Co., Ltd Effective Date: April 2, 2020 Revision Date:

QSF 7.6.4-8 Agent Authorization Letter Template Revision: 0 Page 1 of 1

Antenna specification Model: ESP32-C3 Type: PCB Brand: Espressif Manufacture: Espressif Systems (Shanghai) Co., Ltd. Address: Room 204, Building 2, No. 690 Bibo Road, China (Shanghai) Pilot Free Trade Zone Antenna Gain Table:

Total/Frequency 2400 2450 2500 Efficiency(%) Peak Gain(dBi) 63.87 72.67 67.15 3.59 3.96 3.62 2.4G

---------Horizontal

---------Vertical

---------H+V

---------Horizontal

---------Vertical

---------H+V

---------Horizontal

---------Vertical

---------H+V 2.45G

---------Horizontal

---------Vertical

---------H+V

---------Horizontal

---------Vertical

---------H+V

---------Horizontal

---------Vertical

---------H+V 2.5G

---------Horizontal

---------Vertical

---------H+V

---------Horizontal

---------Vertical

---------H+V

---------Horizontal

---------Vertical

---------H+V 3.Antenna structure drawing Unit: mm

Electronic Way Technology Co., Ltd Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject; Request for Confidentiality FCC ID: 2BC2J-ZBAA409ECS To Whom It May Concern, Date: October 25, 2023 Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: peter cheng Title: manager

Attestation staternents 1 To:Federal Communications Commission Authorization and Evaluation Division 7435(Dakland Mi s ROad Colul bia'VlD 21046P UsA

R noaeAr

lnemear a q 1 1 J u ie

oeuo

(FCC ID:2BC2J-ZBAA409ECS)

EEE~ LIlu1!!L-lu the undersigned`hereby authorize CWATE L1C to E act as our designated tJ.s.agent for serVice of process,ElectroniC Wav rechnology Co Ltd accepts to rnaintain an agent for no less than one vear afterthe grontee has terl inated ali rnarketing and irnpor1 ation or the conclusion of any Conlrnission related proceeding involving the equiprnent. i accepts the responsibility to aCt as designated lJ.s.agent for service of process.

`. ApplicaBit Inforlnation:

`ay Technology Coj`Ltd Con1pany narne:Electronic Contact Name:Peter Cheng Address: No.268 south Jiguang Rd shiPu rown KunshanJJiangsu China 215342 Te|ephone lWo 18098166269 Emaill sales05@mttest,com FRN 0034284729 signature:

Peter Cheng U.s.Agentlnformatbn;

Cornpany NaFne:CYVATE LLC Address:401 RYLAND ST STE 200 A RENo,N\`89502 FR` : 0034366278 Contact Nanle:Williarn Garvis Teiephone No: +1 949374-0632 ~ . Email:Bi|l@cyvate.com signature Z19/K

^LJ VVi|liam R.Garvis 9 `

Electronic Way Technology Co., Ltd Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2023.10.19 FCC ID: 2BC2J-ZBAA409ECS Ref. #1: Attestation Statements Part 2.911(d)(5)(i) Filing

(Electronic Way Technology Co., Ltd) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Ref. #2: Attestation Statements Part 2.911(d)(5)(ii) Filing

(Electronic Way Technology Co., Ltd) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Applicant: Electronic Way Technology Co., Ltd Address: No.268, South Jiguang Rd ShiPu Town, KunShan, JiangSu China 215342 Contact Person: peter cheng Tel.: 18098166269 Email: sales05@mtl-test.com Sincerely, Signature: