RF CCT Controller 70010099 Product Data SR-2833CCT Important: Read All Instructions Prior to Installation Function introduction On/Off Press and hold down to increase light intensity smoothly Control the receiver's cw channel, Press and hold down to increase/
decrease light intensity Control the receiver's ww channel, Press and hold down to increase/
decrease light intensity Output RF signal Operation Frequency 869.5MHz Power Supply 3V(1xCR2025 battery) Operating temperature 0-40C Relative humidity 8% to 80%
Dimensions 136.3x38.9x10.7mm Control 4 zones of RF receiver Dual color controller Compatible with universal serie RF receiver 1 receiver can be paired by max 8 different remote controls. Press and hold down to save color/
scene, click to recall the saved Press and hold down to decrease light intensity smoothly Click to play/pause running mode from Warm White to Cool White Waterproof grade: IP20 Safety & Warnings This device contains a button lithium battery that shall be stored and disposed properly. DO NOT expose the device to moisture. 4 zones, click to choose a zone, press and hold down to turn ON/OFF corresponding zone Pair with RF receiver Front side Step 1:Do wiring the RF receiver according to wiring diagram(please refer to the instruction of RF receiver that you would like to pair with. Step 4:Click any of the four buttons (e.g. ), LED lights connected with the RF receiver flicker once means the receiver is paired with zone 4 successfully. Learning Key RF LED Receiver Click the Learning Key button on RF receiver or re-power on the receiver Step 2:
three times continuously to set it into pairing status Step 3:Choose and click a zone number(e.g. zone 4) Note:Before the first use, please remove the protective film on the battery. Note: one receiver can be paired with max 8 remote controls. Back side Click the paired zone number/numbers, then click the other buttons to do the controlling Operate the remote after pairing If you use multiple receivers, you have two choices:
Option 1: have all the receivers in the same zone, like zone 1 Learning Key RF LED Receiver Learning Key RF LED Receiver Zone 1 RF remote Option 2: have each receiver in a different zone, like zone 1, 2, 3 or 4 Learning Key RF LED Receiver Learning Key RF LED Receiver Learning Key RF LED Receiver Zone 1 Zone 2 Zone 3 RF remote FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. RF CCT Controller 70010146 Product Data Important: Read All Instructions Prior to Installation SR-2833CCT-6Z Function introduction On/Off Press and hold down to increase overall brightness smoothly Control the receiver's CW channel, Press and hold down to increase CW and decrease WW Control the receiver's WW channel, Press and hold down to increase WW and decrease CW Output RF signal Operation Frequency 869.5MHz Power Supply 3V(1xCR2025 battery) Operating temperature 0-40C Relative humidity 8% to 80%
Dimensions 136.3x38.9x10.7mm Control 6 zones of RF receiver Dual color controller Compatible with universal serie RF receiver 1 receiver can be paired by max 8 different remote controls. Press and hold down to decrease overall brightness smoothly 6 zones, click to choose a zone, press and hold down to turn ON/OFF corresponding zone Waterproof grade: IP20 Safety & Warnings Pair with RF receiver This device contains a button lithium battery that shall be stored and disposed properly. DO NOT expose the device to moisture. Front side Step 1:Do wiring the RF receiver according to wiring diagram(please refer to the instruction of RF receiver that you would like to pair with. Step 4:Click any of the four buttons (e.g. ), LED lights connected with the RF receiver flicker once means the receiver is paired with zone 4 successfully. RF LED Receiver Learning Key Step 2:
Click the Learning Key button on RF receiver or re-power on the receiver three times continuously to set it into pairing status Step 3:Choose and click a zone number(e.g. zone 6) Note:Before the first use, please remove the protective film on the battery. Note: one receiver can be paired with max 8 remote controls. Back side Click the paired zone number/numbers, then click the other buttons to do the controlling Operate the remote after pairing If you use multiple receivers, you have two choices:
Option 1: have all the receivers in the same zone, like zone 1 RF LED Receiver Learning Key RF LED Receiver Learning Key Zone 1 RF remote Option 2: have each receiver in a different zone, like zone 1, 2, 3 or 4 RF LED Receiver Learning Key RF LED Receiver Learning Key RF LED Receiver Learning Key Zone 1 Zone 2 Zone 3 RF remote FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.