all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User Manual | Users Manual | 1.19 MiB | ||||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | Operational Description | |||||||
1 | External Photos | |||||||
1 | Internal Photos | |||||||
1 | ID Label/Location Info | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos |
1 | User Manual | Users Manual | 1.19 MiB |
ELESIGN VoIP GATEWAY ESC2420(H.323 Version) User Guide CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the users authority to operate the equipment WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. INFORMATION TO USER:
This equipment has been tested and found to comply with the limit of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation; if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient / Relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit difference from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help ESC2420 User Guide version1.0 About This Manual This Manual provides basic information on how to install and connect Elesign Gateway to the network. It also includes features and functions of Elesign Gateway components, and how to use them. Before Getting Started Before you can connect ELESIGN GATEWAY to the network and use it, you must have a high-speed Internet connection installed. A high-speed connection includes such environments as DSL, cable modem, and a leased line. Precaution Elesign Inc. has copyright to this manual. Any part of this manual cannot be reproduced or transferred electronically, mechanically, or acoustically without permission of Elesign Inc. The material of this manual could be changed for the purpose of the product enhancement. Copyright Elesign Inc. All rights reserved 1 ESC2420 User Guide version1.0 Contents Chapter 1 Summary and Introduction..........4 I. Summary5 II. Introduction...6 Chapter 2 Installation..........7 I. Installation and Procedure at a glance.....8 II. Status Checkup using LED.....11 Chapter 3 PC Network Setup.........12 I. Before Getting Started........13 II. PC Network Setup.......14 Chapter 4 Gateway Network Setup..18 I. Before Getting Started....19 II. Connect to Setup Page........20 III. Gateway Network Setup.........21 Chapter 5 VoIP Setup........23 I. Before Getting Started...24 II. VoIP Setup..............25 III. Make a Call........29 Chapter 6 Advanced Setup......30 I. Console Setup...32 II. Volume Setup................34 III. DHCP Setup.............35 IV. Use NAT Function ......37 V. Phonebook Setup.....39 VI. Firmware Upgrade .......42 2 ESC2420 User Guide version1.0 Chapter 7 Other VoIP Setup Option............43 I. Using Media Gateway......44 II. Direct Call............45 Chapter 8 Appendix...........46 I. How to check MAC Address .......47 II. Configuration and Installation with other equipments ........48 3 ESC2420 User Guide version1.0 Chapter 1 Summary and Introduction I. Summary............5 II. Introduction.......6 1. Contents Checklist.....6 2. Specifications..6 4 ESC2420 User Guide version1.0 I. Summary ESC2420 is a 2-port VoIP gateway and it connects standard telephones and fax machines to IP-based networks. It provides two FXS interfaces and one FXO interface that will enable more calls to be routed through the gateway with or without using directly connected telephones to the gateway. The gateway can be used with Internet connection such as ADSL modem, Cable Modem, and leased Line. The gateway has NAT function, which allows connecting several PCs to use the Internet simultaneously. The basic Internet calls with this gateway are service thru VoIP service provider. With PSTN back up allows to receive a call thru PSTN and automatically switches to PSTN when power-out or problem in networking occurs. 5 ESC2420 User Guide version1.0 II. Introduction 1. Contents Checklist 1) 1 Elesign Gateway (ESC2420) 2) 1 LAN Cable (Blue) 3) 1 Serial Cable (Green) 4) 2 Telephone Lines 5) 1 User Guide 6) 1 Adapter 2. Specifications Item Adapter
(Input/output/frequency) WAN LAN Serial Phone Line Port Reset Switch Optional Features Power Consumption Operating Temperature Relative Humidity Volume Weight Specification 220VA / 12VDC / 60Hz RJ-45 for LAN (10/100baseT) RJ-45 for PC (10/100baseT) RJ-45 for Serial Connector 2 RJ-11 for Telephone 1 RJ-11 for PSTN System Reset Use with PBX & Key phone, Fax Support 2.8W / 3.6W 0~60 5~95%
160mm(W) x 200mm(L) x 33mm(H) 355g 6 ESC2420 User Guide version1.0 Chapter 2 Installation I. Installation and Procedure at a Glance....8 1. Before Installation..........8 1) Check OS of PC used for Installation.......8 2) Check PCs LAN Card..... 8 3) Check Calling Environment....8 2. Procedure at a Glance.......9 3. Installation...10 II. Status Checkup using LED..........11 7 ESC2420 User Guide version1.0 I. Installation and Procedure at a Glance 1. Before Installation 1) Check OS of PC used for Installation You may install the gateway using PC thru Internet browser, Console, or Telnet. Please check OS of the PC that will be used for Installation. (Win98, NT, Me, 2000, XP, Linux). There are minor differences in setting up the network according to OS. 2) Check PCs LAN Card The PC that will be used to install the gateway must have LAN card. Please check if PC has LAN card available. 3) Check Calling Environment Before getting started, check calling environment about how many telephones you want to connect and if you will use existing PSTN network. The telephones that can be directly connected to the gateway are four. You may connect more than four telephones to use Internet call using PBX. You may connect the gateway to PBX, and you can make Internet call from any telephone that is connected to PBX. But you may only make four simultaneous Internet calls at once since the Gateway has only four FXS ports. With PSTN back up allows to receive a call thru PSTN and automatically switches to PSTN when power-out or problem in networking occurs 8 ESC2420 User Guide version1.0 2. Procedure at a Glance Please make sure to follow the procedure. Components Check Up Installation LED Check Up PC Set Up Network Set Up VoIP Set Up Make a call 9 ESC2420 User Guide version1.0 3. Installation (Step of the Procedure)
!! Caution: ADSL MODEM USERS, Please make sure to uninstall ADSL connecting program before starting the installation. 1) Remove the phone line, which is connected from the wall jack to your existing analogue phone, and connect it to Line port. Make sure to leave the handset ON HOOK 2) Find a phone line in the box and connect between VOIP1 port or VOIP2 port and your existing analogue phone 3) Remove from your PC the LAN cable for Internet connection and connect it to WAN port. Some of Modems use Cross LAN cable, so please make sure to use the cable that is connected between your PC and modem to connect from modem to LAN port of Elesign Gateway. 4) Find a LAN cable in the box and connect between LAN port and your PC. 5) Connect an adapter in the box to POWER. Make sure to use the adapter provided with the gateway in the box. 10 ESC2420 User Guide version1.0 II. Status Checkup using LED (Step of the Procedure) LED POWER STATUS WAN LAN PSTN VOIP1 VOIP2 Action Adapter is connected and system is initialized Adapter is not connected The device is registered with a proxy server The device is not registered with the proxy server When only WAN is connected When WAN is not connected or internet service is error When only LAN is connected When LAN is not connected PSTN call is coming or PSTN backup VoIP call mode When the phone connected VOIP1 is off hook When the phone connected VOIP1 is on hook When the phone connected VOIP2 is off hook When the phone connected VOIP2 is on hook LIGHT ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF 11 ESC2420 User Guide version1.0 Chapter 3 PC Network Setup I. Before Getting Started........13 1. LED Check.......13 2. Check Internet Connection........13 1) Leased Line Static IP Users.......13 2) ADSL Users.....13 II. PC Network Setup.........14 1. ADSL Modem Users...14 2. VDSL Modem Users...14 3. Cable Modem Users....14 4. Leased Line Dynamic IP Users...14 5. Lease Line Static IP Users...14 1) Win98/WinMe Users........14 2) Win2000/WinXP Users........16 6. Check PCs IP address.......17 12 ESC2420 User Guide version1.0 To use the gateway, you need to setup the network of PC and the gateway. To connect PC and the gateway, you need to confirm the PCs network setup. After the confirmation, you need to setup the network of PC and the gateway according to the Internet connection. I. Before Getting Started Before getting started, please confirm the matters below. 1. LED Check Look into the page11 to check the installation. If the color doesnt match with current installation, there might be problems regarding the connection, PC, or PCs LAN card. Please check the connection of the modem, PCs LAN card, or the gateway. 2. Check Internet Connection You need to setup the network of PC and the gateway according to the current Internet connection. Please confirm the current connection (ADSL, Cable, Lease line), and check the necessary information for setup. 1) Leased Line Static IP Users When setup the network of PC, write down the network information. (IP address, subnet mask, gateway, DNS) They are necessary information for the network setup of the gateway. 2) ADSL users Please check the ID and password that is used in connecting to Internet. They are necessary information for the network setup of the gateway. Before starting the network setup of PC, you need uninstall the ADSL connection program from PC. 13 ESC2420 User Guide version1.0 II. PC Network Setup (Step of the Procedure) 1.ADSL Modem Users After the installation, restart PC. If the PC is turned off, simply start the PC. 2.VDSL Modem Users After the installation, restart PC. If the PC is turned off, simply start the PC. 3.Cable Modem Users After the installation, restart PC. If the PC is turned off, simply start the PC. If you are using cable modem with static IP, go to Leased line static IP to setup network of PC. 4. Leased Line Dynamic IP Users After the installation, restart PC. If the PC is turned off, simply start the PC. 5. Lease Line Static IP Users 1) WIN98/WinME Users Click on Start button Select Control Panel from setting of start menu. Select Network from control panel 14 ESC2420 User Guide version1.0 Select TCP/IP and click on Property button Select Obtain an IP address automatically and click on OK button Popup window will appear to restart the computer, then restart the computer right away by clicking on OK button 15 ESC2420 User Guide version1.0 2) Win2000/WinXP Users Click on Start button Select Control Panel from Setting of start menu. Select Network. Select Local Connection Click on Properties button Select TCP/IP and click on Property button. Select Obtain an IP address automatically and click on OK button. Click on OK to close window. 16 ESC2420 User Guide version1.0 6. Check PCs IP address This step is to make sure that PC for the installation and the gateway is connected. Before you connect to the setup page using Web browser, check PCs IP address for correct installation and PC network setup. 1) Click on Start button and select RUN. 2) Enter CMD (Win2000/WinXP Users) or COMMAND (Win98/WinMe Users) and click on OK button to see a window as below. 3) When there is a prompt C:W>, enter ipconfig and hit enter to see IP information. 4) If IP address is 10.0.1.X and Default Gateway is 10.0.1.1 then the installation is correct and network of PC is setup accordingly. 17 ESC2420 User Guide version1.0 Chapter 4 Gateway Network Setup I. Before Getting Started...19 1.Check Internet Connection........19 1) Leased Line Static IP Users......19 2) ADSL Users.........19 II. Connect to Setup Page.......20 III. Gateway Network Setup...........21 1. Connect to Network Setup Page.......21 2. Network Setup according to Internet Connection..21 3. Confirmation of Setup...22 4. When Failed to Setup....22 18 ESC2420 User Guide version1.0 After PC Network Setup, you need to setup the network of the gateway. You may setup according to your Internet Connection. I. Before Getting Started Before getting started, please confirm the matters below. 1. Check Internet Connection You need to setup the network of PC and the gateway according to the current Internet connection. Please confirm the current connection (ADSL, Cable, Lease line), and check the necessary information for setup. 1) Leased Line Static IP Users When setup the network of PC, write down the network information. (IP address, subnet mask, gateway, DNS) They are necessary information for the network setup of the gateway. 2) ADSL Users Please check the ID and password that is used in connecting to Internet. 19 ESC2420 User Guide version1.0 II. Connect to Setup Page 1 2 Start Internet browser in PC. (i.e. Click on explorer icon.) Input http://10.0.1.1 in address box and hit enter. 3 When window appears to input ID and password for network, input root for ID and root for Password. Click on OK to connect to the main page. You may change ID and password. (Refer to page 31, Console Setup for more information.) 4 When you see a window above, click on necessary setup item to go on setting up. 20 ESC2420 User Guide version1.0 III. Gateway Network Setup (Step of the Procedure) 1. Connect to Network Setup Page 1) From main page, select Network setup. 2) Select the network type according to the Internet connection and input necessary information. 2. Network Setup according to Internet connection 1) ADSL Users Check ADSL and input ID and password that is used in connecting to Internet and click on OK button. 2) VDSL Modem Check Dynamic IP & Cable Modem and click on OK button. 3) Cable modem Users Check Dynamic IP & Cable Modem and click on OK button. Some of Cable service provider check on MAC address of PCs LAN card. You might not be able to connect to Internet if this is the case. Please contact you local cable service representative. 4) Leased Line Dynamic IP Users Check Dynamic IP & Cable Modem and click on OK button. 5) Lease Line Static IP Users Check Static IP and input IP address, gateway, subnet mask and DNS. Click on OK button. 21 ESC2420 User Guide version1.0 3. Confirmation of Setup 1) When you see a message, connecting for NETWORK STATUS, please click on HERE where it says Please click HERE to see current proceedings. 2) If you see a message, Connected for Network Status, the network setup is successfully done. 4. When Failed to Setup If you dont see a message, Connected for about a minute, check the items below according to Internet connection. 1) ADSL Users:
You might have failed to login. Check the ID and Password and try to restart ADSL modem by rebooting. 2) VDSL Users:
Try to restart VDSL modem by rebooting, or check the physical connections and try again. 3) Cable Modem Users Try to restart cable modem by rebooting, or check the physical connections and try again. 4) Leased Line Dynamic IP Users Check the physical connection and try again. 5) Leased Line Static IP Users Check if the IP address and other information are correct and try again. Also if DNS address is not correct, Internet thru PC might not be possible, so check to make sure the address is right. 22 ESC2420 User Guide version1.0 Chapter 5 VoIP Setup I. Before Getting Started.......24 1. Checkpoint.......24 2. Confirmation of VoIP Service Mode.....24 1) Terminal Type .24 2) Gateway Type......24 II. VoIP Setup.......25 1. Connect to Setup page....25 2. Connect to VoIP Setup page.......25 3. VoIP Setup.......26 1) Register as Terminal Type...26 2) Register as Gateway Type...27 4.When Failed to Setup......28 III. Make a Call......29 23 ESC2420 User Guide version1.0 In order to make an Internet call, VoIP setup is necessary to register to VoIP service. First, if you subscribe for the service, you will receive the necessary information to register from Service Company. I. Before Getting Started 1. Checkpoint The necessary information when registering are E.164 (internet phone number), H.323ID, Password, etc. It may be different from a company to a company. Check to make sure you have all the necessary information before getting started. 2. Confirmation of VoIP Service Mode There are different types of service from one Service Company to another. Select the VoIP setup mode according to your service provided. Make sure to check the mode and setup accordingly, otherwise, you may have problem registering. 1) Terminal Type If there are 2 of H323 ID necessary to register, you need to setup as Terminal for Terminal Type. Typically you need 2 of H323 ID and 2 of E.164 (Internet Telephone Number) for this type of service. 2) Gateway Type If there is 1 of H323ID necessary to register, you need to setup as Gateway for Terminal Type. Typically you need 1 of H323 ID and 2 of E.164 (Internet Telephone Number) for this type of service. 24 ESC2420 User Guide version1.0 II. VoIP Setup (Step of the Procedure) 1. Connect to Setup page Connect to Setup page. Refer to page20 Connect to Setup page. If you are already in Setup page, start from number 2 Connect to VoIP Setup page. 2. Connect to VoIP Setup page Select VoIP Setup from Main Page 25 ESC2420 User Guide version1.0 3. VoIP Setup 1) Register as Terminal Type First, subscribe for Internet call service to get necessary information. Input gatekeeper IP address in GATEKEEPER box. (Ex: 123.123.123.123) Leave blank for GATEWAY box. (For more information regarding setup of media gateway, refer to page44) Input area code used with PSTN in AREA CODE box. (Ex: Seoul 02) Select Gatekeeper Routed for CALL MODEL Select Terminal for Terminal Type Enter H323ID and E164 received from the service company to each box of the channel. Click on OK button. When you see a message, Registering for VoIP Status, please click on HERE where it says Please click HERE to see current proceedings. 26 ESC2420 User Guide version1.0 If you see a message, Registered for VoIP Status, the VoIP setup is successfully done. 2) Register as Gateway Type First, subscribe for Internet call service to get necessary information. Input gatekeeper IP address in GATEKEEPER box. (Ex: 123.123.123.123) Leave blank for GATEWAY box. (For more information regarding setup of media gateway, refer to page44) Input area code used with PSTN in AREA CODE box. (Ex: Seoul 02) Select Gatekeeper Routed for CALL MODEL Select Gateway for Terminal Type Enter H323ID for Channel 1 and E.164 (Internet Telephone number) for each box of the channel. 27 ESC2420 User Guide version1.0 Click on OK button. When you see a message, Registering for VoIP Status, please click on HERE where it says Please click HERE to see current proceedings. If you see a message, Registered for VoIP Status, the VoIP setup is successfully done. 4. When Failed to Setup If you dont see a message Registered for about a minute, check to make sure you have inputted the information correctly. Try again after checking the necessary information regarding the registration. 28 ESC2420 User Guide version1.0 III. Make a Call (Step of the Procedure) Dial the number Press # (Send) The way to make an Internet call may differ from a service company. In order to receive further information, contact the service company. 29 ESC2420 User Guide version1.0 Chapter 6 Advanced Setup I. Console Setup...32 1.Connect to Setup page.......32 2.Connect to Advanced Setup page.........32 3.Getting used to Console Setup..............32 1) Volume Setup...33 2) Tone Setup.......33 3) Virtual IP Setup...............33 4) NAT Setup...............33 5) Console ID & Password Setup........33 6) Confirmation of Setup.........33 II. Volume Setup...34 1.Connect to Setup page... ..34 2.Connect to Advanced Setup page.........34 3.Volume Setup..............34 III. DHCP Setup.....35 1. DHCP Setup...........35 2.Connect to Setup page.......35 3. Connect to Advanced Setup page............35 4. DHCP Setup...............36 IV. Using NAT Function......37 1. NAT Function.......37 2. Configuration of NAT......37 1) Configuring NAT......37 2) Port Forwarding Setup...38 30 ESC2420 User Guide version1.0 V. Phonebook Setup...39 1. Before Getting Started........39 2. Register Individual Information....39 1) Connect to Setup page.......39 2) Connect to Phonebook Setup page........39 3) Register Individual Information........40 3. Register Representative Gateway......41 VI. Firmware Upgrade ..42 1. Connect to Setup page42 2. Connect to Advanced Setup page......42 3. Firmware Upgrade.....42 31 ESC2420 User Guide version1.0 This chapter is to setup the advanced option other than basic setup to make an Internet call. You may setup to use advanced option according to network environment. I. Console Setup 1. Connect to Setup page Connect to Setup page. Refer to page20 Connect to Setup page. If you are already in Setup page, start from number 2 Connect to Advanced Setup page. 2. Connect to Advanced Setup page Select Advanced Setup from the main page. 3. Getting Used to Console Setup Select Console Setup from the submenu of Advanced Setup. 32 ESC2420 User Guide version1.0 1) Volume Setup This option is to adjust the volume. Refer to page34 for more detailed procedure. 2) Tone Setup This option is to select the dial ton according to the different countries. The gateway has 4 types of tone, Korean, Japanese, China 3 (TUP), and Guandong. You may distinguish the tone between the Internet call and PSTN call using this option. 3) Virtual IP Setup Virtual IP means the network ID of the LAN side of the gateway. This option allows you to change the network ID since there may be the case where same network ID present within the same network. If you change the IP address from 10.0.1.1 (default) to 10.0.10.1, virtual IP addresses that are allocated from the gateway range from 10.0.10.2 to 10.0.10.254. Virtual IP is used to connect to setup page of the gateway. It is needed to reconnect to the page, so please remember the value after changing it.
(Ex: If Virtual IP is changed to 10.0.10.1, the connecting IP address will change also to http://10.0.10.1)
! Caution: After changing the Virtual IP, reboot the gateway and restart the computer that is connected to the gateway. You may not be able to connect to the page if you forget the changed value. 4) NAT Setup This option is to Enable or Disable NAT function. 5) Console ID and Password Setup This option is to change Console ID and Password that is used to connect to setup page. Make sure to remember the changed values.
! Caution: You may not be able to connect to the page if you forget the changed value. 6) Confirmation of Setup Click on OK button after setup. To store the setup values, disconnect the adapter and reconnect to restart the gateway. 33 ESC2420 User Guide version1.0 II. Volume Setup 1. Connect to Setup Page Connect to Setup page. Refer to page20 Connect to Setup page. If you are already in Setup page, start from number 2 Connect to Advanced Setup page. 2. Connect to Advanced Setup Page Select Advanced Setup from the main page. 3. Volume Setup 1) Select Console Setup from the submenu of Advanced Setup. 2) Select the appropriate volume from 1~5 to adjust. 3) Click on OK button. 4) To store the setup values, disconnect the adapter and reconnect to restart the gateway. 34 ESC2420 User Guide version1.0 III. DHCP Setup 1. DHCP Setup This option is to restrict the usage of NAT function. The default setup of the gateway allows you to connect the several computers and the gateway automatically allocates the private IP. In situation like this, DHCP setup will allows to restrict the allocation of IP to particular PC. There is setup option of Use above IP pool only in DHCP setup page. If you want to allocate the IP without any restriction, leave it to OFF. When it is setup to ON, PCs, other than that are connected to the gateway already, will not receive any IP address from the gateway. In situation like this, use DHCP setup to manually add PC using MAC address of PC. Using MAC address of PC, you may allocate virtual IP to PC. The procedure is described below. 2. Connect to Setup Page Connect to Setup page. Refer to page20 Connect to Setup page. If you are already in Setup page, start from number 3 Connect to Advanced Setup page. 3. Connect to Advanced Setup Page Select Advanced Setup from the main page. 35 ESC2420 User Guide version1.0 4. DHCP Setup 1) Select DHCP Setup from the submenu of Advanced Setup. 2) Select ON for the setup option of Use above IP Pool only. 3) Select virtual IP address that will be allocated to PC. The IP address that can be used ranges 10.0.1.2 to 10.0.1.254. 4) Check the MAC address of PC and input in the box. Click on ADD button. Refer to page47 for How to check MAC address of PC. 36 ESC2420 User Guide version1.0 IV. Using NAT Function 1. NAT Function NAT Function is to allocate private IP to PCs connected to the gateway and enables the usage of Internet. However, the speed of Internet Connection may go down, if three or more simultaneous calls are on and more than 20 PCs are connected. 2. Configuration of NAT Using private IP allocated from the gateway, you may connect more than one PC to use Internet. 1) Configuring NAT If you would connect one or several PC to the gateway, the gateway allocates private IP to PC for NAT environment. Connect Several PCs to the gateway using
(Refer to page10 for installation) Change the network of PC (other than one that used for setup) to Obtain IP dynamically (Refer to page12). After setup, turn of the PCs and disconnect the adapter from the gateway. Connect the adapter to the gateway and check LED. Restart the PC and wait for about a minute Check to make sure you are able If you are not able to connect to to connect to Internet from every Internet, refer to page12 for PC that is connected to the Network Setup of PC. gateway. 37 ESC2420 User Guide version1.0 2) Port Forwarding Setup This function enables you to connect to Internet site that uses special port. If Internet programs dont work properly, you need to setup for IP address and port forwarding according to the programs. Connect to Setup page. Refer to page20 Connect to Setup page. If you are already in Setup page, start from number 2 Connect to Advance Setup page. Select Advanced Setup from main page. Select NAT Setup from submenu of ADVANCED SETUP Input IP address of PC to setup the option. Select transmitting protocol and input the port number. Then click on ADD button. To delete the IP address, input IP address and click on DELETE button. 38 ESC2420 User Guide version1.0 V. Phonebook Setup This option allows you to make a direct call using extension without using Gatekeeper. 1. Before Getting Started 1) Select the members to form a Group (Maximum 50 person) 2) Decide the name of Group (Maximum 14 letters using English, Korean, Number, or Special Character) 3) Decide the password of Group (Maximum 14 letters using English, Korean, Number, or Special Character) 4) Decide the host name for each member to use within the Group (Maximum 30 letters using English, Korean, Number, or Special Character) 5) Decide the extension (3 digit number) of each member to use within the Group. 6) Decide the representative gateway within the Group and let members of the group know the IP address of it. 2. Register Individual Information 1) Connect to Setup Page Connect to Setup page. Refer to page20 Connect to Setup page. If you are already in Setup page, start from number 2 Connect to Phonebook Setup page. 2) Connect to Phonebook Setup Page Select Phonebook from the main page. 39 ESC2420 User Guide version1.0 3) Register Individual Information Input Group name. Input Group password. Input Hostname. Input Extension number. Select Enable for Ext Enable. EXT ENABLE option allows to register other members of the group automatically even though only one member of the group is registered. Select enable for Renewal Enable. RENEWAL ENABLE option allows to update the latest information of other members of the group. If IP address of one of the gateway changes, it will automatically update new IP address on the list. And if one of the gateways is disconnected from the network, it will automatically be removed from the list. Click on Register button to register. Click on Home button to go to main page. You may see the extension information for each channel. 40 ESC2420 User Guide version1.0 3. Register Representative Gateway 1) Select Phonebook from the main page. 2) Input IP address of representative gateway. 3) Click on ADD button to register. 4) If representative gateway is added, you will be able to see the information (IP address, Extension and Host name) of other members within the group in the list. Check the list of IP address and extension.
! Caution: If there are same extensions used by two or more people, you cant make a call using that extension. If there is same extension within a Group, please re-register with new extension. 41 ESC2420 User Guide version1.0 VI. Firmware Upgrade Firmware Upgrade should be performed automatically. This option is for user to manually upgrade the firmware. 1. Connect to Setup Page Connect to Setup page. Refer to page20 Connect to Setup page. If you are already in Setup page, start from number 2 Connect to Advanced Setup page. 2. Connect to Advanced Setup Page Select Advanced Setup from the main page. 3. Firmware Upgrade 1) Select Remote Upgrade from the submenu of Advanced Setup. 2) Confirm the version of the firmware. 3) Leave IP address of server and input the filename that is needed to be downloaded. (Make sure to use the correct filename.) 4) Click on OK button. 5) Check to makes sure that you see a message Success for Upgrade Status. You may check the version of firmware after downloading is done. 42 ESC2420 User Guide version1.0 Chapter 7 Other VoIP Setup Option I. Media Gateway Setup.........44 1. Connect to Setup page..44 2. Connect to VoIP Setup page.........44 3. Media Gateway Setup.......44 4. Make a call using Media Gateway...44 II. Direct Call............45 1. Connect to Setup page......45 2. Connect to VoIP Setup page.........45 3. Direct call Setup........45 4. Extension Call setup.....45 5. Make a direct to call.................45 43 ESC2420 User Guide version1.0 I. Media Gateway Setup Certain service company uses Media gateway for VoIP service. When this is the case, follow the procedure below to setup to use media gateway. 1. Connect to Setup Page Connect to Setup page. Refer to page20 Connect to Setup page. If you are already in Setup page, start from number 2 Connect to VoIP Setup page. 2. Connect to VoIP Setup Page Select VoIP setup from the main page. 3. Media Gateway Setup 1) Enter gateway address in the GATEWAY box. 2) Select Direct for CALL MODEL. 3) Click on OK button. 4) When you see the confirmation page, you may check the result of the setup. 4. Make a call using Media Gateway To get information regarding making a call, contact the service company. 44 ESC2420 User Guide version1.0 II. Direct call Setup This option is to make a direct call between gateways without VoIP service. If setup is done for direct call, you may call to Netmeeting or PC Phone. 1. Connect to Setup Page Connect to Setup page. Refer to page20 Connect to Setup page. If you are already in Setup page, start from number 2 Connect to VoIP Setup page. 2. Connect to VoIP Setup Page Select VoIP Setup from the main page. 3. Direct Call Setup 1) Select Direct for CALL MODEL 2) Click on OK button. 3) When you see the confirmation page, you may check the result of the setup. 4. Extension Call setup Refer to page39 for Phonebook setup for extension call. 5. Make a Direct Call Dial Extension number that is designated to each channel of the gateway. Ex) If extension is 200, 200+#(send) 45 ESC2420 User Guide version1.0 Chapter 8 Appendix I. How to Check MAC Address ..47 II. Configuration and Installation with other equipments..48 1. Connect to PBX .....48 46 ESC2420 User Guide version1.0 I. How to check MAC Address 1. Open Command window. (Dos window) 2. When you see a prompt, C:W>, input ipconfig/all and hit enter. You will see Physical address, and that is the MAC address of PC. 47 ESC2420 User Guide version1.0 II. Configuration and Installation with other equipments 1. Connect to PBX The telephones that can be directly connected to the gateway are two. You may connect more than two telephones to use Internet call using PBX. You may connect the gateway to PBX, and you can make Internet call from any telephone that is connected to PBX. But you may only make two simultaneous Internet calls at once since the Gateway has only two FXS ports. For more detailed information regarding the installation, contact the specialist. 48 ESC2420 User Guide version1.0 www.ELESIGN.com 49
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2005-04-14 | JBP - Part 15 Class B Computing Device Peripheral | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2005-04-14
|
||||
1 | Applicant's complete, legal business name |
Elesign INC.
|
||||
1 | FCC Registration Number (FRN) |
0004265807
|
||||
1 | Physical Address |
404, KOLON techno valley, 60-4, Kasan-dong
|
||||
1 |
Seoul, N/A 153-801
|
|||||
1 |
South Korea
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
h******@americantcb.com
|
||||
1 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
P5E
|
||||
1 | Equipment Product Code |
ESC2420
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
L******** G****
|
||||
1 | Title |
Associate Research Engineer
|
||||
1 | Telephone Number |
82-2-******** Extension:
|
||||
1 |
l******@elesign.com
|
|||||
app s | Technical Contact | |||||
1 | Firm Name |
ES Tech
|
||||
1 | Name |
J****** Y****
|
||||
1 | Physical Address |
97-1 Hoiuk-Ri Majang-Myon
|
||||
1 |
Icheon City, KyngKi-Do, 467-811
|
|||||
1 |
South Korea
|
|||||
1 | Telephone Number |
82-54********
|
||||
1 | Fax Number |
82-54********
|
||||
1 |
j******@estech.co.kr
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | JBP - Part 15 Class B Computing Device Peripheral | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | 2-Port VoIP Gateway | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Estech Co., Ltd.
|
||||
1 | Name |
I******** C****
|
||||
1 | Telephone Number |
82-2-********
|
||||
1 | Fax Number |
82-2-********
|
||||
1 |
i******@estech.co.kr
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15B |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC