Equipment Tag with Input Instruction Manual and Specsheet FCC Compliance The FCC Wants You to Know This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
a) Reorient or relocate the receiving antenna. b) Increase the separation between the equipment and receiver. c) Connect the equipment to an outlet on a circuit is to which receiver from that the different connected. d) Consult the dealer or an experienced radio/TV technician. FCC Warning Modifications not expressly approved by manufacturer could void the user authority to operate the equipment under FCC rules. 15.9 (a) Labeling Requirements This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IR and RF Equipment Tag with Input P/N: WSE00433 (433.92 MHz) Description A small, attachable portable device, capable of transmitting Infra Red signals in addition to RF signals in the frequency of 433.92 MHz. It is used for the purposes of locating, monitoring and protecting mobile equipment in enclosed environments and for providing various location dependent functions. The inclusion of the input provides an indication of the short and open states of the input. General Input Transmissions Electrical power source Data rate Message protocol Message duration Battery type Battery life Short accepts dry contacts of less than 10k Open accepts dry contacts more than 1M Note: No voltage should be applied between the two input wires. The transfer from open to short or from short to open triggers the following transmissions:
Open to short 4 badge transmissions at 0.4 sec apart with B2 high Short to open - 4 badge transmissions at 0.4 sec apart with B2 low In Steady State, B2 indicates the following input states:
Low open High short One 3-Volt lithium battery 19,200 bits per second 4 bytes proprietary format 2.08 ms CR 2032 Renata Five years, assuming movement 1 hr / day Battery status indication Badge ID Dimensions Weight
(including battery) Temperature:
Operating Temperature:
Storage Humidity:
Operating Humidity:
Storage Water resistance IR Transmission Modulation Peak optical transmitted power Peak transmission wavelength Peak radiant intensity Frequency of transmission Transmission rate Transmission angle Battery status transmitted with every RF and IR message Unique factory programmed (ID code, transmit rate, motion sensor activation and deactivation, etc.) 39 x 39 x 16 mm 25 gram
-10 to 70C
-20 to 60C 5 to 95% RH @ 70 C 5 to 95% RH @ 85 C Waterproof ASK (Amplitude Shift Keying of IR carrier) 500mW 880nm 120 mW/Sr Carrier at 455 KHz During movement every 3 to 5 sec message. During rest (no movement) every 60 sec. 360 badge plane. 60 to badge perpendicular axis. RF Transmission 433.92 MHz ASK (Amplitude Shift Keying of 433.92 MHz carrier) In motion: less than 35 dbm. Motionless: less than 45 dbm Modulation Average effective radiated power Stability Peak ERP Transmission pattern FCC compliance FCC Part 15.231 Level C
+/- 20ppm
-15 dbm (max) Omnidirectional Using the Equipment Tag with Input The following is a set of procedures to ensure proper use of the Equipment Tag. To use the Equipment Tag with Input:
1. 2. 3. Use some glue to attach the Equipment Tag to a piece of equipment. A press button is available, if required. Connect the two wires together to activate the input sensor. Battery Replacement The Equipment Tag contains a standard Lithium battery of type CR2032. The battery is located inside the Equipment Tag. In order to replace the battery, you need to open the back side of the equipment tag with a Phillips screwdriver
(preferably an electric one) with point size "0". For example, the APEX #4910. A new battery can then be inserted, after which the screws must be replaced.