FCC ID: A4E-P4 Wireless Charging Holder

P4 User Manual Caution Before use of unit, please read the Manual carefully. Keep the product away from water, liquid, or wet area. Keep the product away from naked ame. The unit should be powered o before unplugging. Do not place the product in direct sunlight or heat. Keep away from temperatures over 35C. Do not attempt to remove the unit. To remove panel or attempt to repair the unit could result in potential electric shock. Do not insert foreign objects into the product. Adult Supervision is recommended if children are using this product. 1 Wireless Charging Holder USB Power grommet Wireless Charging Cord Switch power supply 2 Drawing Specications Wireless Charging: 5 V , 1 A . U SB: 5V, 4A. 3 Installation 1 Drill hole 25.5

+0.5

-0.0 2 Install screws 3 Install cover 4 FCC Requirement Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is measures:

connected. Consult the dealer or an experienced radio/TV technician for help.

60mm eMoMo Product name:Wireless Charging Holder Model No.: P4 Input: 5V=== 4A FE (+ Ds USB Output: 10W =

Wireless Charging Output: 5W FCC ID: A4E-P4 35mm This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Va

(eMoMo Technology Co.,Ltd Made In China P4ins ine, REBS

eMoMo Technology Co., Ltd Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: A4E-P4 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type 1. Block Diagram, 2. Schematics, 3. Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commissions public notice, we also request temporary confidential treatment of information accompanying this application as outlined below for an initial period of xxxx (ie- 45, 90 or 180) days:

Exhibit Type N/A File Name 1. A4E-P4 -Block diagram 2. A4E-P4 -SCH 3. A4E-P4 -Operational description File Name N/A Signature:

Contact name: Rosary Tang Company name: eMoMo Technology Co., Ltd Address: Fourth Floor, Yonghe Building, Taiwan Industrial P Shiyan, Baoan, Shenzhen,Guangdong,China Date: 04/17/2018 VCB_F-01: Operating Procedures Form FCC Confidentiality v02 Page 1 of 1

eMoMo Technology Co., Ltd Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 2022-6-2 SUBJECT: FCC Application for (FCC ID:A4E-P4) To Whom It May Concern:

We, the undersigned, hereby authorize Yoyo Zhou in Shenzhen Huaxia Testing Technology Co., Ltd at 1F., Block A of Tongsheng Technology Building, Huahui Road, Dalang Street, Longhua District, Shenzhen, China on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Shenzhen Huaxia Testing Technology Co., Ltd on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely,

(Must be signed by the person that is listed on the FCC Website) Signature:

Contact name: Rosary Tang Company name: eMoMo Technology Co., Ltd Address: Fourth Floor, Yonghe Building, Taiwan Industrial P Shiyan, Baoan, Shenzhen,Guangdong,China Date: 04/17/2018 VCB_F-01: Operating Procedures Form FCC Authorization v02 Page 1 of 1

eMoMo Technology Co., Ltd Model Confirmation Letter We, (eMoMo Technology Co., Ltd) certify the product:

Wireless Charging Holder Model No.: P4,P4(G), P4(S),P4.29,P4A,P4B,P4C,P4D,P4E,P4EA,P4F,P4F(R)-F, P4-LT05,P4-WE03 Their electrical circuit design, identical,Only the model or colors is different. layout, components used and internal wiring are Signiture:

Grantee Contact: Rosary Tang Company Name: eMoMo Technology Co., Ltd Date:2022-6-2