2.4GHz Wireless Video Sender Receiver MODEL:VST-2500/VSR-2500AM TINSE061C--001 PRINTED IN CHINA 1 2 3 4 1 2 3 4 2.4GHz WIRELESS T R A N S MIT T E R W I R E L E S S R E C E I V E R 2
. 4 G H z Table of Contents 1. Location of Controls On Sender 2. Location of Controls On Receiver 3. Channel & Timer Setting 4. 4. AC/DC Adaptor Operation 5. Antenna Operation 6. Connections/Setting up 7. Specifications 1 2 3 4 5 6~7 8 Specifications General:
Location of controls on Sender 1.Operation Frequency: 2400MHz-2483.5MHz 8. Power Supply 2.Usable range: 50~100 Meter (open side) Adaptor :DC 12V 0.2/0.3A 1. Patch Antenna FRONT 3. Operation Temperature:-10~50 C 9. Dimension:
Sender unit 1. Transmit Frequency:
107W x43Hx123Dm/m 2400~2483.5MHz Receiver unit 2. Microwave Output Power:94dbu(3m) 3. Modulation: FM 4. Maximum Frequency Deviation: 20 MHz 5. Video: a) Input Impedance: 1Vpp 75 ohm b) Frequency Response:0~5Mhz 6. Audio:
a) Input Impedance: 10K ohm b) Interface Level:1 Vpp c) Frequency Response:300-3400Hz d). Audio Sub, Carrier Frequency: 6.0 MHz, 6.5MHz 7. Operation Current:200 MA Max. 1. Receiver Frequency:2400~2483.5MHz 2. Receiver Sensitivity:-80 ~ -85 dBm 3. Video Output: 1 Vpp 75 ohm 4. Audio Output: -8dBs 47K ohm 5. Monitor Center horizontal Resolution:
330 lines 6. Operation Current:
200mA Max. 7
. Power Supply:
Adaptor: DC 12V 0.2/0.3A 1 2 2. Channel Indicator 3. Power ON/OFF Switch 2.4GHz WIRELESS T R A N S MIT T E R 1 2 3 4 4. DC Input Jack REAR 5. Audio Input Jack 6. Video In put Jack INPUT CH L R VIDEO AUDIO AUDIO DC 12V IN ON OFF 7 6 45 3 8. Dimension:
107W x43Hx123Dm/m 7. Channel Selector 8 1 Location of controls on Receiver Receiver unit REAR 1. Patch Antenna FRONT 2. Channel Indicator W I R E L 2
. 4 G H z 3. Power ON/OFF Switch E S S R E C E I V E R 1 2 3 4 4. DC Input Jack REAR 5. Audio Output Jack 6. Video Output Jack 7. Channel Timer Selector TIMER 1 2 3 4 5 6 CH ON OUTPUT L R VIDEO AUDIO AUDIO DC 12V IN ON OFF 7 6 45 3 2 1 2 TIMER 1 2 3 4 5 6 CH ON OUTPUT L R VIDEO AUDIO AUDIO DC 12V IN ON OFF WHITE YELLOW YELLOW RED INPUT VIDEO L R AUDIO AUDIO WHITE RED One Receiver can Receive 4 Channels sig al from 4 senders n with different direction or You can select any one even other Combination which depends on channel setting. The timer switch can select switcher time from 3 sec to 10 sec. Refer to channel & timer setting. 1.Connet the Video and Audio output signal of receiver with AV wire to your TV or Monitor . If connect to TV, You have to switch your TV to
"A V INPUT"function . 2. If your TV SET with AV output Jack .You can connect to a VCR for recording. 7 Connections/setting up Sender unit REAR INPUT CH L R VIDEO AUDIO AUDIO DC 12V IN ON OFF WHITE RED YELLOW YELLOW OUTPUT VIDEO AUDIO AUDIO L R WHITE RED The sender can input video and stereo or mono audio signal from camera, DVD, VCR, satellite receiver, TV--ect.and then transmit to the Receiver without wire around 100 meters at the open side. If indoor use ,the distance will Base on the building construction. 1.Conect the yellow plug into the video input Jack of sender 2.Conect the red plug into the audio R input Jack of sender 3.Conect the white plug into the audio L input Jack of sender 4.Plug the other end to the signal source, be sure that yellow plug into video output ,red plug to the R channel of Audio output ,white plug into the L channel of Audio output. Channel & Timer Setting Channel Setting RECEIVER UNIT SENDER UNIT TIMER 1 2 3 4 5 6 DIP ON CH 1 2 3 4 ON CH 1.The channel & Timer selector on the The channel selector on the rear cabinet rear cabinet are used to set channel are used to set channel No which you
& timer. Put Theswitch to ON position want to transmit. and then you can select single channel 1~4 or any other channel combination. Put one of four switch to ON position as you prefer. Don t SET more than one channel to 2.Timer setting function as below. on position. Switcher time Sw5 Sw6 3sec 5sec 7sec 10sec ON ON ON OFF OFF ON OFF OFF 6 3 AC/DC Adaptor Operation Antenna Operation AC/DC Adaptor 1. If the sender unit is far away from the Receiver unit , pls turn TX side of antenna on unit to directly face antenna on Receiver unit RF SIGNAL UPWARD TIMER 1 2 3 4 5 6 CH ON OUTPUT L R VIDEO AUDIO AUDIO DC 12V IN ON OFF Make sure that proper AC/DC adaptor have been installed correctly, use only the AC/DC adaptor supplied with the sender and receiver 1. Plug of the AC/DC Adaptor to the DC input jack of the unit. Plug the adaptor into a standard wall outlet. 2. Switch on the power switch of the unit. 3. The channel indicator LED will be illuminated. to get best reception. TX SIDE OF ANTENNA 2.4GHz WIRELESS T R A N S MIT T E R 1 2 3 4 2. If the sender unit is close to the Receiver unit
, due to multi path reason, RF sometimes you have to put both antennas 3. Place the sender unit in the most appropriate location for monitoring
(tabletop, dresser or wall mount) as higher as possible. Make sure that both units are on the same channel. of sender unit
Receiver unit to face 4. In case of poor display quality, rotate upward to void something moving between the antennas or reposition both units TX and RX which may affect the picture to obtain optimum picture transmission. stability. 4 5