FCC ID: 2A3G3-WMX720X Wi-Fi 6E BT 5.2 M.2 2230 Module, Wi-Fi 6E BT 5.2 Mini PCIe Module

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6447475.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case User Guide EmWicon Corporation 7F.-5, No. 258, Liancheng Rd., Zhonghe Dist. New Taipei City 235 Taiwan Product Overview The devices Wi-Fi 6E BT 5.2 Mini PCIe Module contain a Qualcomm chip for Wireless LAN applications. Wi-Fi 6E BT 5.2 Mini PCIe Module support key security features like Wi-Fi Protected Access (WPA), WPA2, WEP, 802.1x. Typical application of the card is integration into other wireless products such as AP/ Router which is used distance 20 cm away human body. Packaging Contents The package contains the following item(s):

1 x Wi-Fi 6E BT 5.2 Mini PCIe Module Installation guide Shut down the power of the platform Align the Wi-Fi 6E BT 5.2 Mini PCIe Module with the Mini PCIe Type socket on the platform Adjust and push down the Wi-Fi 6E BT 5.2 Mini PCIe Module gently until the metal locking levers on the Mini PCIe type socket is latched. (Please take note that the Wi-Fi 6E BT 5.2 Mini PCIe Module can only fit in one direction due to the keyed notch. Wrong orientation will cause improper installation and may damage the Mini PCIe Type socket) Connect the antenna(s) on the Wi-Fi 6E BT 5.2 Mini PCIe Module Reboot on the platform Install drivers if necessary Frequency 2400~ 2483.5 MHz 2402 ~ 2480 MHz 5150 ~ 5850 MHz 5850 ~ 5895 MHz 5925 ~ 7125 MHz Connector: I-PEX MHF1 PLUG EmWicon Corporation 7F.-5, No. 258, Liancheng Rd., Zhonghe Dist. New Taipei City 235 Taiwan Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. EmWicon Corporation 7F.-5, No. 258, Liancheng Rd., Zhonghe Dist. New Taipei City 235 Taiwan Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM Manual v01 guidance, the following conditions must be strictly followed when using this certified module:

KDB 996369 D03 OEM Manual v01 rule sections:

2.2 List of applicable FCC rules This module has been tested for compliance to FCC Part 15 2.3 Summarize the specific operational use conditions The module is tested for standalone mobile RF exposure use condition. Any other usage conditions such as co-location with other transmitter(s) or being used in a portable condition will need a separate reassessment through a class II permissive change application or new certification. 2.4 Limited module procedures Not applicable. 2.5 Trace antenna designs Not applicable. 2.6 RF exposure considerations This equipment complies with FCC mobile radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. If the module is installed in a portable host, a separate SAR evaluation is required to confirm compliance with relevant FCC portable RF exposure rules. 2.7 Antennas The following antennas have been certified for use with this module. The antenna must be installed such that 20 cm can be maintained between the antenna and users. 2.8 Label and compliance information The final end product must be labeled in a visible area with the following: Contains FCC ID:

2A3G3-WMX720X. The grantee's FCC ID can be used only when all FCC compliance requirements are met. EmWicon Corporation 7F.-5, No. 258, Liancheng Rd., Zhonghe Dist. New Taipei City 235 Taiwan 2.9 Information on test modes and additional testing requirements This transmitter is tested in a standalone mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) or portable use will require a separate class II permissive change re-evaluation or new certification. 2.10 Additional testing, Part 15 Subpart B disclaimer This transmitter module is tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of rule requirements if applicable. As long as all conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product

(including the transmitter) and obtaining a separate FCC authorization. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. OEM/Host manufacturer responsibilities OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and EMF essential requirements of the FCC rules. This module must not be incorporated into any other device or system without retesting for compliance as multi-radio and combined equipment. Prohibited for control of or communications with unmanned aircraft systems, including drones. EmWicon Corporation 7F.-5, No. 258, Liancheng Rd., Zhonghe Dist. New Taipei City 235 Taiwan

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6447476.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case User Guide EmWicon Corporation 7F.-5, No. 258, Liancheng Rd., Zhonghe Dist. New Taipei City 235 Taiwan Product Overview The devices M.2 E(2230) Type adapter cards contain a Qualcomm chip for Wireless LAN applications. The M.2 E(2230) Type adapter cards support key security features like Wi-Fi Protected Access (WPA), WPA2, WEP, 802.1x. Typical application of the card is integration into other wireless products such as AP/ Router which is used distance 20 cm away human body. Packaging Contents The M.2 E(2230) Type card package contains the following item(s):

1 x Wi-Fi 6 802.11ax 2x2 dual-band M.2 E(2230) Type Module Installation guide Shut down the power of the platform Align the M.2 E(2230) Type adapter with the M.2 E(2230) Type socket on the platform Adjust and push down the M.2 E(2230) Type adapter gently until the metal locking levers on the M.2 E(2230) Type socket is latched. (Please take note that the M.2 E(2230) Type adapter can only fit in one direction due to the keyed notch. Wrong orientation will cause improper installation and may damage the M.2 E(2230) Type socket) Connect the antenna(s) on the M.2 E(2230) Type module Reboot on the platform Install drivers if necessary Frequency 2400 ~ 2483.5 MHz 2402 ~ 2480 MHz 5150 ~ 5850 MHz 5850 ~ 5895 MHz 5925 ~ 7125 MHz Connector: I-PEX MHF4 PLUG EmWicon Corporation 7F.-5, No. 258, Liancheng Rd., Zhonghe Dist. New Taipei City 235 Taiwan Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. EmWicon Corporation 7F.-5, No. 258, Liancheng Rd., Zhonghe Dist. New Taipei City 235 Taiwan Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM Manual v01 guidance, the following conditions must be strictly followed when using this certified module:

KDB 996369 D03 OEM Manual v01 rule sections:

2.2 List of applicable FCC rules This module has been tested for compliance to FCC Part 15 2.3 Summarize the specific operational use conditions The module is tested for standalone mobile RF exposure use condition. Any other usage conditions such as co-location with other transmitter(s) or being used in a portable condition will need a separate reassessment through a class II permissive change application or new certification. 2.4 Limited module procedures Not applicable. 2.5 Trace antenna designs Not applicable. 2.6 RF exposure considerations This equipment complies with FCC mobile radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. If the module is installed in a portable host, a separate SAR evaluation is required to confirm compliance with relevant FCC portable RF exposure rules. 2.7 Antennas The following antennas have been certified for use with this module. The antenna must be installed such that 20 cm can be maintained between the antenna and users. 2.8 Label and compliance information The final end product must be labeled in a visible area with the following: Contains FCC ID:

2A3G3-WMX720X. The grantee's FCC ID can be used only when all FCC compliance requirements are met. EmWicon Corporation 7F.-5, No. 258, Liancheng Rd., Zhonghe Dist. New Taipei City 235 Taiwan 2.9 Information on test modes and additional testing requirements This transmitter is tested in a standalone mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) or portable use will require a separate class II permissive change re-evaluation or new certification. 2.10 Additional testing, Part 15 Subpart B disclaimer This transmitter module is tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of rule requirements if applicable. As long as all conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product

(including the transmitter) and obtaining a separate FCC authorization. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. OEM/Host manufacturer responsibilities OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and EMF essential requirements of the FCC rules. This module must not be incorporated into any other device or system without retesting for compliance as multi-radio and combined equipment. Prohibited for control of or communications with unmanned aircraft systems, including drones. EmWicon Corporation 7F.-5, No. 258, Liancheng Rd., Zhonghe Dist. New Taipei City 235 Taiwan

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6447422.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case

Certification designating a U.S. Agent for service of process:

As required by section 2.911(d)(7), the applicant must designate a contact located in the United States for purposes of acting as the applicants agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. In either scenario, the designation of the U.S. agent for service of process should be provided as an attachment to the equipment authorization application. The applicant must provide a written certification, which must:

i. Be signed by both the applicant and designated agent for service of process, if the agent is different from the applicant. ii. Acknowledge the applicants consent and the designated agents obligation to accept service of process. iii. Provide a physical U.S. address and email for the designated agent. iv. Acknowledge the applicants acceptance to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Unofficial information provided by FCC personnel on February 14, 2023, via the monthly call with the TCB Council:

The Agent for Process of Service:

cannot be a TCB or affiliated with a TCB (e.g. could not be a person who works for a TCB or a company that owns or is owned by the TCB) cannot be a [FCC recognised] Lab or affiliated with a test lab (e.g. could not be a person who works for a Lab or a company that owns or is owned by the Lab) Agent can be Individual Entity or a Company Entity Agent Entity must be located in US, US address/phone Entity acting as Agent must have FRN (best practice, put FRN on Agent Letter) Agent letter does not have to be FCC ID specific, can be general Agent for Grantee For devices being marketed or for which marketing has ceased for less than 1 year, if the Agent for Process of Service changes, then for every TC Number the TCB must request the FCC to put application into Audit Mode and Agent Letter needs to be updated (superseded). NOTE: The U.S. Agent for Service of Process should not be confused with the authorized agent used for signing the 731 form, other cover letters within the application, and/or the agent who may interface with the TCB. 7F.-5, No. 258, Liancheng EmWicon Rd., Zhonghe Corporation New Taipei Dist., 235 City, Taiwan U.S. Agent Designation for Service of Process ATTENTION: Federal Communications and Evaluation Mills Road . Authorization 7435 Oakland Columbia, Commission Division MD 21046 USA REGARDING: FCC Certification

-Section 2.91 l(d)(7) Information Inc. U.S. Agent Address:

Name: Approve-IT, Name: Nathan Grinager Designated Company Contact 8011 34th Ave South, Street City/Province/Zip:

Telephone No: 651-247-1678 Email:

FRN #: 0027533835 Suite 342 MN 55425 Bloomington, team@approve-it.net This letter Designated noted below. is to confirm that we ("the U.S. Agent for Service Designated U.S. Agent) as required of Process have accepted the responsibility to act as the by section 47 CFR 2.91 l(d)(7) on behalfofthe Applicant U.S. Agent Signature:

Date:

March 17, 2023 Signed by (Printed

*This letter TCB for device certification Nathan Grinager Name/Title):

(update must be dated within 1-year

/ Co-President applv) if other terms of the date the application is submitted to the confirms The Applicant year after terminating involving the equipment. Designated U.S. Agent information The applicant fu1iher above changes. its explicit all marketing consent and impo1iation and acknowledges that they must maintain an agent for no less than one OR the conclusion proceeding of any Commission-related acknowledges their responsibility tlie to inform the FCC whenever class 2 permissive change, class 3 permissive change, etc.) transmitter or limited single-modular transmitter) Rd., Zhonghe Dist., Type: (original Applicant Company name: EmWicon Corporation Service application, FCC ID: 2A3G3-WMX720X Module type: (single-modular Contact Street City/Province/Zip:

Telephone

@en Email:

New Taipei No: 886-2-82271348 Name: Eddie Lin Address:

eddie_lin City, Taiwan 235 No. 258, Liancheng 7F.-5, Applicant Signature:

Date:3/17/2023

'\. Name/fftle):

Signed by (Printed

*By signing applicable applicable declares the client for the module model described in any way to any host devices and agrees above. The client that could contain this letter, Eddie Lin/ R&D Vice President also declares the module for which the service and accepts that the service provided by Approve-IT, that the service Inc. will only be won't be has been contracted.

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6447469.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6447470.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6447471.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case FCC ID: 2A3G3-WMX720X Description of Permissive Change The application is prepared for FCC class II permissive change. The difference compared with the original design are:

1. Adding two models:

The EUT has below model names, and they are identical to each other in all aspects except for the following:

2. Adding new antenna FCC ID: 2A3G3-WMX720X Regards, Andrea Hsia/ Supervisor Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Tel: 886-3-318 3232 ext. 1628 Fax: 886-3-327 0892 Email: andrea.hsia@tw.bureauveritas.com Data: 2023-01-09

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6447472.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case