FCC ID: LCGVU121 Bluetooth Low Energy Adapter for Liquiphant ES series

unbekannt unbekannt 2019-06-30 Products Solutions Services Special Documentation Bluetooth module VU121 Remote operation via Bluetooth wireless technology About this document Bluetooth module VU121 1 About this document 1.1 Symbols Tip Indicates additional information. Reference to another chapter. Documentation Designated use 1.2 1.2.1 Remote operation of devices via Bluetooth wireless technology Suitable for the following device versions Device: Liquiphant FTL51B Firmware version: 01.00.zz or higher Device version: 1 Incorrect use The manufacturer is not liable for damage caused by improper or non-designated use. Under different operating conditions than those described here, protection may be compromised and the correct functioning of the device cannot be guaranteed. Declaration of Conformity 1.2.2 The Bluetooth module VU121 meets all the applicable EC Directives. Registered trademarks 1.3 Bluetooth The Bluetooth word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Endress+Hauser is under license. Other trademarks and trade names are those of their respective owners. Apple Apple, the Apple logo, iPhone, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc. Android Android, Google Play and the Google Play logo are trademarks of Google Inc. 2 V. 1, Rev. 2, 23-04-2019 Endress+Hauser A Bluetooth module VU121 Radio approvals 2 Radio approvals Europe 2.1 This device meets the requirements of the Telecommunications Directive RED 2014/53/EU:

EN 300 328 V2.1.1 EN 301 489-1 V2.1.1 EN 301 489-17 V3.1.1 EN 62311: 2008 Canada and United States English 2.2 2.2.1 This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this equipment not expressly approved by Endress+Hauser SE+Co. KG may void the FCC authorization to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Radiofrequency radiation exposure information This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Endress+Hauser V. 1, Rev. 2, 23-04-2019 3 Operation options Bluetooth module VU121 Franais 2.2.2 Le prsent appareil est conforme aux CNR d'industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :

L'appareil ne doit pas produire de brouillage, et L'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Les changements ou modifications apports cet appareil non expressment approuvs par Endress+Hauser SE+Co. KG peuvent annuler l'autorisation FCC d'utiliser cet appareil. Dclaration d'exposition aux radiations Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Ce transmetteur ne doit pas tre plac au mme endroit ou utilis simultanment avec un autre transmetteur ou antenne. Japan 2.3 Japanese Radio Law and Japanese Telecommunications Business Law Compliance. This device is granted pursuant to the Japanese Radio Law () and the Japanese Telecommunications Business Law (). This device should not be modified (otherwise the granted designation number will become invalid). Other countries 2.4 Other national approvals are available on request. 3 Operation options 3.1 Access via Bluetooth wireless technology Remote operation via Bluetooth wireless technology Smartphone or tablet with SmartBlue (app) Device with optional Bluetooth module A0033411 V. 1, Rev. 2, 23-04-2019 Endress+Hauser 1 1 2 4 12 Bluetooth module VU121 Operation options Preparatory steps 3.2 Note down the ID number of the Bluetooth module. The ID number on the nameplate of the Bluetooth module is used as the initial password when establishing the connection for the first time. The high cover with the window must be used for devices that are operated with the Bluetooth module. A0039040 Functions 3.3 Connection via COM interface: Bluetooth module for device diagnostics via a smartphone app or tablet app Heartbeat Technology functions Diagnostics: Read out the current diagnostics Verification: Create the verification report Monitoring: Historical record of the frequency Display the battery status via app when used with electronic insert FEL68 (NAMUR) User guidance (wizard) for SIL/WHG proof testing Visible in the livelist 10 seconds after the Bluetooth search commences Data can be read out of the Bluetooth module 60 seconds after the supply voltage has been switched on Display of the current vibration frequency and the switching state of the device The yellow LED flashes when the Bluetooth module is connected to another Bluetooth device, e.g. a cellular phone Technical data 3.4 Maximum free-field range 50 m (165 ft) Operation radius with intervisibility 10 m (33 ft) around the device Supply voltage: 3 VDC with max. 5.5 VDC and min. 2.7 VDC Power consumption: max. 5.5 mW Current consumption: 1 mA Pollution degree: 2 Endress+Hauser V. 1, Rev. 2, 23-04-2019 5 ID:__________________________________XXX-XXXXXX Commissioning Bluetooth module VU121 Temperature range: 40 to +85 C (40 to +185 F) Relative humidity: operation up to 100% in the measuring devices ( designated use). Do not open in a condensing environment!

Suitable for wet environments, integrated in measuring devices ( designated use). 3.4.1 Replacement batteries for FEL68 (2-wire NAMUR) Only the following types of AA 3.6 V lithium batteries made by the following manufacturers are suitable for use:

SAFT LS14500 TADIRAN SL-360/s XENOENERGY XL-060F Operating altitude 3.4.2 As per IEC 61010-1 Ed.3:

Up to 2 000 m (6 600 ft) above sea level Can be extended to 3 000 m (9 800 ft) above sea level if overvoltage protection is used 4 Commissioning Requirements 4.1 Device requirements Commissioning via SmartBlue is only possible if a Bluetooth module is installed in the device. System requirements SmartBlue is available as a download from the Google Play Store for Android devices and from the iTunes Store for iOS devices iOS devices: iPhone 4S or higher from iOS9.0; iPad2 or higher from iOS9.0; iPod Touch 5th generation or higher from iOS9.0 Devices with Android: from Android 4.4 KitKat and Bluetooth 4.0 Initial password The ID number (serial number) on the nameplate of the Bluetooth module is used as the initial password when establishing the connection for the first time. It is important to note the following if the Bluetooth module is removed from one device and installed in another device: all log-in data are only stored in the Bluetooth module and not in the device. This also applies to the password changed by the user. 6 V. 1, Rev. 2, 23-04-2019 Endress+Hauser Bluetooth module VU121 Commissioning 4.2 1. Establishing a connection via SmartBlue (app) Scan the QR code or enter "SmartBlue" in the search field. 2 Download link A0039186 2. 3. 4. Start SmartBlue. Select device from livelist displayed. Log-in:

User name: admin Password: ID number (serial number) on the Bluetooth module 5. For more information, tap the icons. Change the password after logging in for the first time!

Endress+Hauser V. 1, Rev. 2, 23-04-2019 7

*unbekannt*

unbekannt www.addresses.endress.com

Sample Agency Request Letter Authority to Act as Agent Date: 20.07.2019 TUV Rheinland Group 762 Park Avenue Youngsville, NC 27596 To Whom It May Concern:

I appoint TUV Rheinland LGA Products GmbH to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the FCC or Industry Canadas regulations will have affixed to it a label identical to that submitted for approval with this application. For TCB applications, We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, By : {Lp Db; IE Ralf Reimelt fe 7 Mey :

(SignatureY (Print Name) Title : Group Leader R&D Telephone : +49 7622 28 1890 On behalf of : Endress+Hauser SE+Co. KG

(Company Name)

Endress+Hauser (21) People for Process Automation Confidentiality Letter Date: 2019/08/12 Subject: Confidentiality Request for FCC ID: LCGVU121 and IC ID: 2519A-VU121 Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC/IC application be held confidential. Type of Confidentiality Requested

[_] Short Term [><] Permanent Block Diagrams x] Short Term [_] Permanent Internal Photos L] Short Term | x] Permanent _| Operation Description/Theory of Operation

[_] Short Term [x] Permanent Part List/Tune-Up Procedure

[_] Short Term Xx] Permanent Schematics

[1shortterm | SS~*d Users Manual SSSC~S~CS Endress+Hauser SE+Co. KG has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TUV Rheinland in the event information regarding the product or the product is made available to the public. TUV Rheinland will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705.

, Sf cy. l

(Signature/Title) Sincerely, By: Dr. Arno Gtz

(Print name)

1/1

Testing and certification of electronic and electric appliances, systems, installations and telecommunication systems PHOTOGRAPHS OF THE EXTERIOR OF A MODEL VU121 Page 1 of 10 TV Rheinland Nederland B.V. Eiberkamp 10 9351VT Leek The Netherlands Telephone: +31 888887888 Internet: www.tuv.com/nl E-mail: products@nl.tuv.com Table of contents 1 PHOTOGRAPHS OF THE EQUIPMENT. ....................................................................................................................... 3 1.1 LEFT SIDE VIEW. ............................................................................................................................................................. 3 1.2 RIGHT SIDE VIEW. ........................................................................................................................................................... 4 1.3 FRONT VIEW. .................................................................................................................................................................. 5 1.4 REAR VIEW. .................................................................................................................................................................... 6 1.5 BOTTOM VIEW ................................................................................................................................................................. 7 1.6 TOP VIEW ........................................................................................................................................................................ 8

.................................................................................................................................................................................................... 8 2 TEST SAMPLE PHOTOS .................................................................................................................................................. 9 Page 2 of 10 1 Photographs of the equipment. 1.1 Left side view. Page 3 of 10 1.2 Right side view. Page 4 of 10 1.3 Front view. Page 5 of 10 1.4 Rear view. Page 6 of 10 1.5 Bottom view Page 7 of 10 1.6 Top view Page 8 of 10 2 Test sample photos Page 9 of 10 END OF DOCUMENT Page 10 of 10

Date 27-05-2019

: LCGVU121 To whom it may concern, On behalf of our customer Endress+Hauser SE+Co. KG, we hereby declare the following device:

FCC ID IC : 2519A-VU121 Brand Model The EUT has one transmitter (BLE). The RF exposure assessment is based on the BLE mode. The EUT is considered as Mobile use. The EUT has a maximum rated output power in BLE mode of 2.4 mW in the frequency range of 2402 2480 MHz which means that the worst case prediction of power density

(100% reflection) at 20 cm distance (worst case) can be calculated as follows :

: VU121

: Endress+Hauser EIRP

* EIRP S = 4 * * R2 (power density without reflection) 22 S = 4 * * R2 (power density with 100% reflection) 22 S = 4 * * R2 = * (20cm)2 = * (20)2 = 0.0021 mW/cm2

(limit =10 W/m2 is 1.0 mW/cm2)

* EIRP EIRP (mW) 2.6 ___ This means that the equipment is in compliance with FCC KDB Publication 447498, 47 C.F.R. 1.1310 and 2.1091 fulfils the requirements of RSS-102 Issue 5 Section 2.5.2. stating: at or above 300 MHz and below 6 GHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 1.31 x 10-2 0.6834 W (adjusted for tune-up tolerance), where is in MHz. For this EUT the this calculates to: 1.31 x 10-2 (2402 0.6834) = 2.68 W. The EUTs maximum rate output power (EIRP) of 2.6 mW is within this requirement. Note: For conservativeness, the lowest frequency is used for calculation. Best regards, TV Rheinland Nederland B.V. R .van der Meer, Test Engineer

FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 1 of 47 Client:

Test Item:

Endress+Hauser SE+Co.KG Hauptstrasse 1, 79689 Maulburg, Germany Contact: Harald Schuble Digital System (DTS) Bluetooth Low Energy Adapter for Liquiphant ES series Identification:

VU121 Serial Number:

2539ZBTH_1810.0

(conducted sample)

-

(radiated sample) Project No.:

19040102 Date of Receipt:

April 29, 2019 Testing Location:

Test Specification:

TV Rheinland Nederland B.V. Eiberkamp 10 9351VT Leek FCC 47 CFR Part 15, Subpart C, Section 15.247 (10-1-18 Edition) RSS-Gen (Issue 5, April 2018) and RSS-247 (Issue 2, February 2017) ANSI C63.10-2013 KDB 558074 D01 DTS Meas Guidance v05.02 Test Result:

The test item passed the test specification(s). Testing Laboratory:

TV Rheinland Nederland B.V. Eiberkamp 10 9351 VT Leek Tested by:

Reviewed by:

2019-07-03 Date R. van der Meer / Inspector Name/Position Signature 2019-07-03 Date E. van der Wal / Reviewer Name/Position Signature Other Aspects:AC Power Line conducted emission tests were not requested as that will be tested in the final application. Abbreviations:

P(ass) = passed F(ail) N/A N/T

=

= not applicable

= not tested failed This report shall not be reproduced, except in full, without the written permission of TV Rheinland Nederland B.V. The test results relate only to the item(s) tested. FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 2 of 47 TEST SUMMARY 5.1.1 CONDUCTED MEASUREMENTS AT ANTENNA PORT RESULT: PASS 5.1.2 6DB AND 99% BANDWIDTH RESULT: PASS 5.1.3 PEAK POWER SPECTRAL DENSITY RESULT: PASS 5.1.4 Emissions on non restricted bands RESULT: PASS 5.1.5 BAND EDGE CONDUCTED EMISSIONS RESULT: Pass 5.1.6 RADIATED SPURIOUS EMISSIONS OF TRANSMITTER RESULT: PASS 5.2.1 AC POWER LINE CONDUCTED EMISSION OF TRANSMITTER RESULT: N/A FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

Contents 19040102.r01 Page 3 of 47 1. GENERAL REMARKS ............................................................................................... 4 1.1 COMPLEMENTARY MATERIALS ................................................................................. 4 2. 2.1 2.2 TEST SITES ............................................................................................................ 4 TEST FACILITIES ..................................................................................................... 4 LIST OF TEST AND MEASUREMENT INSTRUMENTS TABLE 1: LIST OF TEST AND MEASUREMENT EQUIPMENT ..................................................................................... 5 2.3 MEASUREMENT UNCERTAINTY ................................................................................. 6 3. 3.1 3.2 GENERAL PRODUCT INFORMATION ........................................................................... 7 PRODUCT FUNCTION AND INTENDED USE .................................................................. 7 SYSTEM DETAILS .................................................................................................... 7 3.3 COUNTERMEASURES TO ACHIEVE COMPLIANCE ......................................................... 8 4. TEST SET-UP AND OPERATION MODES ..................................................................... 9 4.1 TEST METHODOLOGY .............................................................................................. 9 4.2 OPERATION MODES ................................................................................................ 9 4.3 4.4 4.5 PHYSICAL CONFIGURATION FOR TESTING ............................................................... 10 TEST SOFTWARE .................................................................................................. 12 SPECIAL ACCESSORIES AND AUXILIARY EQUIPMENT ............................................... 13 5. TEST RESULTS ..................................................................................................... 14 5.1 CONDUCTED MEASUREMENTS AT ANTENNA PORT .................................................. 14 5.1.1 Conducted Output Power ........................................................................................................... 14 5.1.2 6dB and 99% Bandwidth ............................................................................................................ 17 5.1.3 Peak Power Spectral Density .................................................................................................... 22 5.1.4 Emissions in non-restricted bands ............................................................................................. 25 5.1.5 Band Edge Conducted Emissions ............................................................................................. 28 5.1.6 Radiated Spurious Emissions of Transmitter ............................................................................. 31 5.2 AC POWER LINE CONDUCTED MEASUREMENTS ...................................................... 47 FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 4 of 47 1. General Remarks 1.1 Complementary Materials There is no attachment to this test report. 2. Test Sites 2.1 Test Facilities The Federal Communications Commission and Industry Canada has reviewed the technical characteristics of the test facilities at TV Rheinland Nederland B.V., located in Leek, 9351VT Eiberkamp 10, The Netherlands, and has found these test facilities to be in compliance with the requirements of 47 CFR Part 15, section 2.948. The description of the test facilities has been filed at the Office of the Federal Communications Commission under registration number 786213. The facility has been added to the list of laboratories performing these test services for the public on a fee basis. The description of the test facilities has been filed to Industry Canada under registration number 2932G-2. The facility has been added to the list of laboratories performing these test services for the public on a fee basis. Normal test conditions:

Temperature (*) Relative humidity(*) Supply voltage : 3 VDC.

(*)When it was impracticable to carry out the tests under these conditions, a note to this effect stating the ambient temperature and relative humidity during the tests are stated separately.

: +15C to +35C

: 20 % to 75 %

FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 5 of 47 2.2 List of Test and Measurement Instruments Table 1: List of Test and Measurement Equipment Kind of Equipment Manufacturer Model Name For Antenna Port Conducted Emissions Inventory number Calibration Calibration date

(mm/yyyy) due date

(mm/yyyy) Temperature-

Humiditymeter Extech SD500 A00446 06/2018 06/2020 Spectrum Analyzer Rohde & Schwarz FSV A01744 RF Cable Huber + Suhner Sucoflex 102 A00347 07/2018 06/2018 07/2020 06/2020 For Radiated Emissions Measurement Receiver Rohde & Schwarz ESR7 RF Cable S-AR Gigalink Controller Controller Maturo EMCS Test facility Comtest APG0500 SCU/088/

8090811 DOC202 FCC listed:

786213 IC: 2932G-2 Spectrum Analyzer Rohde & Schwarz FSV Antenna mast Temperature-

Humiditymeter Guidehorn 1-18 GHz Guidehorn 18-40 GHz Biconilog Testantenna 2.4 GHz bandreject filter EMCS Extech EMCO EMCO Teseq BSC Bandpass filter 4-10 GHz Reactel AP-4702C SD500 3115 RA42-K-F-4B-C CBL 6111D XN-1783 7AS-7G-6G-

511 9HS-

A01982 A00447 A00450 A00257 07/2018 03/2019 07/2019 03/2020 N/A N/A N/A N/A A00235 10/2017 10/2020 A00337 A00258 07/2018 07/2019 N/A N/A A00444 06/2018 06/2019 A00008 A00012 A00466 A00065 A00131 12/2017 01/2018 11/2018 12/2020 01/2021 11/2019 N/A N/A N/A N/A N/A N/A Bandpass filter 10-26 GHz Preamplifier 0.5 - 18 GHz Reactel 10G/26.5G-

A00151 Miteq S11 AMF-5D-

005180-28-

13p A00247 N/A N/A Filterbox EMCS RFS06S A00255 04/2019 04/2020 Conformance of the used measurement and test equipment with the requirements of ISO/IEC 17025:2005 has been confirmed before testing. NA= Not Applicable FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 6 of 47 2.3 Measurement Uncertainty Table 2: Emission Measurement Uncertainty Measurement Type Antenna Port Conducted Emission Radiated Emission Frequency

< 1.3GHz 1.3 - 40GHz 150kHz - 30MHz 30MHz - 1GHz

> 1GHz Uncertainty 1.7dB 2.9 3.4dB 5.0dB 5.22dB 5.22dB FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 7 of 47 3. General Product Information 3.1 Product Function and Intended Use The brand Endress+Hauser model VU121, hereafter referred to as EUT, is a Bluetooth BLE transmitter. The transmitter will support and utilizes GFSK modulation techniques. The content of this report and measurement results have not been changed other than the way of presenting the data. 3.2 System Details Details and an overview of the system and all of its components, as it has been tested, may be found below. EUT Manufacturer Brand Model(s) FVIN Voltage input rating Voltage output rating Current input rating Antenna Antenna Gain Operating frequency Modulation Data-rate Remarks

: Digital Transmission System, BLE

: Endress+Hauser SE+Co. KG

: Endress+Hauser

: VU121

: S112 v6.1.1

:

:

:

:

:

:

: GFSK

:

:

3 Vdc (2.7 5.5 Vdc)

--

--

Internal, integrated on the PCB 0.4 dBi 2402 MHz-2480 MHz. 1 Mbps n.a. FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 8 of 47 Table 3: Interfaces present on the EUT There are no interface ports present on the EUT. 3.3 Countermeasures to achieve compliance No additional measures were employed to achieve compliance. FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 9 of 47 4. Test Set-up and Operation Modes 4.1 Test Methodology The test methodology used is based on the requirements of RSS-GEN, RSS-247, 47 CFR Part 15, Sections 15.31, 15.33, 15.35, 15.205, 15.207, 15.209, 15.247. The test methods, which have been used, are based on ANSI C63.10-2013 and KDB 558074. 4.2 Operation Modes Testing was performed at the lowest operating frequency (2402 MHz), at the operating frequency in the middle of the specified frequency band (2440 MHz) and at the highest operating frequency (2480 MHz). These operation modes were selected after review of the capabilities and characteristics of the EUT. The test software as mentioned in section 4.4 enabled the settings of these modes. The EUT has been tested in the modes as described in table below Operation Mode Transmit (Tx) Transmit (Tx) Transmit (Tx) EUT Status On On On Frequency

(MHz) 2402 (Ch 0) 2440 (Ch 19) 2480 (Ch 39) TX power control setting max max max The EUT was set in payload model PRBS9 with a payload length of 37 Bytes. FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 10 of 47 4.3 Physical Configuration for Testing For programming purposes only the EUT was connected to the usb port of a laptop computer. The laptop computer was used to configure the EUT to continuously transmit at a specified output power and channel as specified in the test data. See section 4.5 for Auxiliary details. The EUT was tested on a stand-alone basis and the test system was configured in a way that a load condition was emulated by a bicycle wheel that was spun by a controllable speed. The justification and manipulation of cables and equipment in order to simulate a worst-case behavior of the test setup has been carried out as prescribed in ANSI C63.10-2013. Figure 1: Test Setup Diagram antenna port conducted tests and programming. Laptop Computer

(AUX1) 1 mains mains 2 EUT 3 Spectrum Analyzer

(for Antenna-port conducted tests) No. Port 1. Mains 2. Data com. 3. Antenna port From Mains Laptop USB EUT To Laptop (AUX1) EUT Spectrum analyzer Remarks Through a power supply

--

Conducted tests FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 11 of 47 Spectrum analyzer 3 1 AUX1 2 EUT Figure 2: Test Setup Photos conducted tests and programming Figure 3: Test Setup Photos radiated tests and programming FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 12 of 47 4.4 Test Software A continuous transmit mode could be initiated by using test software as supplied by the applicant. The test software was used to define various different operational modes of the EUT for the purpose of compliance testing. The version of the test software, as supplied by the applicant and used during all tests is:

Test software In Direct Test mode a modulated wave with payload PRBS9, payload length 37 was set. This software was running on a laptop computer (AUX1). It was used to enable the test operation modes listed in section 4.2 as appropriate.

: Nordic nRFgo studio Screenshot of the software as used on AUX1 FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 13 of 47 4.5 Special Accessories and Auxiliary Equipment Assetnumber:

Laptop Computer DELL 5490 A000223238-001 host for test software, property applicant The product has been tested together with the following additional accessories:

The auxiliary items were not used during testing, but instead are only used to make the required settings for testing. For setting the transmit frequency, enable modulation etc. 1. AUX1 Product:

Brand:

Model:

Remark:

FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 14 of 47 5. Test Results 5.1 Conducted Measurements at Antenna Port 5.1.1 Conducted Output Power RESULT: PASS Date of testing:

Requirements:

FCC 15.247(b)(3) 2019-05-06 For systems using digital modulation in the 2400-2483.5 MHz band, the maximum peak output power is 1W (+30dBm). RSS-247 section 5.4(4): the e.i.r.p. shall not exceed 4 W (+36 dBm). Test procedure:

The Peak Conducted Output Power was measured using the method according to section 11.9.1.1 in ANSI C63.10-2013. The maximum peak output power (conducted) was measured at the antenna connector with a spectrum analyzer. The final measurement takes into account the loss generated by all the involved cables. Measurement uncertainty is +/- 2.5 dB. Notes: mW = 10 ^ (dBm/10) dBm = 10 x log(mW) plots 4: Peak power plots, Figures 1a, 1b and 1c show plots of the Peak Power outputs, correction factors (= 0.24dB Cableloss) included in the reading. FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 15 of 47 Conducted Output Power Frequency Output Power Limit Verdict

[dBm]

[dBm]

[Pass/Fail]

Plot number

[MHz]

2402 2440 2480 3.71

( 0.00235 W) 3.76

(0.00238 W) 3.77

( 0.00238 W)

+30

(1W)

+30

(1W)

+30

(1W) Pass Pass Pass A B C Plot A Date: 6.MAY.2019 09:47:27 FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 16 of 47 Plot B Plot C Date: 6.MAY.2019 09:48:29Date: 6.MAY.2019 09:49:08 FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 17 of 47 5.1.2 6dB and 99% Bandwidth RESULT: PASS Date of testing:

Requirements:

2019-05-06 & 2019-07-03 FCC 15.247(a)(2) and RSS-247 Section 5.2(1) For systems using digital modulation in the 2400-2483.5MHz band, the 6dB bandwidth shall be at least 500kHz. For 99% Bandwidth: RSS-Gen Section 4.6.1: No requirement is given. Test procedure 6dB bandwidth:

ANSI C63.10-2013 section 11.8.1 Option 1 A spectrum analyzer was connected to the antenna port of the EUT. The spectrum analyzer resolution bandwidth was set to 100kHz, video bandwidth to 300kHz and the span wide enough to capture the modulated carrier. For 99% Bandwidth:

RSS-Gen. The transmitter shall be operated at its maximum carrier power measured under normal test conditions. The span of the analyzer shall be set to capture all products of the modulation process, including the emission sideskirts. The resolution bandwidth shall be set as close to 1%

of the selected span as is possible without being below 1%. The video bandwidth shall be set to 3 times the resolution bandwidth. Video averaging is not permitted. Where practical, a sampling detector shall be used given that a peak or peak hold may produce a wider bandwidth than actual. A spectrum analyzer was connected to the antenna port of the EUT. The spectrum analyzer resolution bandwidth was set to 1% of the selected span, Video bandwidth was set to 3 times the resolution bandwidth. The span was set to capture the whole modulation process. The Spectrum analyzers automated function for 99% BW was used. Measurement uncertainty is +/- 26kHz. Plots A1,B1 and C1 shown on the next pages are of the 6 dB bandwidth. Plots A2,B2 and C2 shown on the next pages are of the 99% bandwidth FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 18 of 47 6dB and 99 percent Bandwidth Operating Frequency

[MHz]

2402 2440 2480 99%

6dB Limit Verdict Plot Bandwidth Bandwidth 6dB BW

[Pass/Fail]

number

[kHz]

1040.1 1044.4 1045.5

[kHz]

707.7 711.4 712.0

[kHz]

>500

>500

>500 Pass Pass Pass A1/A2 B1/B2 C1/C2 Plot A1 Date: 6.MAY.2019 09:29:34 FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 19 of 47 Plot B1 Plot C1 Date: 6.MAY.2019 09:33:10Date: 6.MAY.2019 09:33:59 FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 20 of 47 Plot A2 Plot B2 FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 21 of 47 Plot C2 FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 22 of 47 5.1.3 Peak Power Spectral Density RESULT: PASS Date of testing:

Requirements:

2019-05-06 FCC 15.247(e) and RSS-247 section 5.2(2) For digitally modulated systems, the power spectral density (PSD) conducted from the intentional radiator to the antenna shall not be greater than 8dBm in any 3kHz band during any time interval of continuous transmission. Test procedure:

ANSI C63.10-2013 The section 11.10.2 PKPSD peak PSD procedure was used. A spectrum analyzer was connected to the antenna port of the EUT. The analyzer resolution bandwidth was set to 3kHz and the video bandwidth was set to 10kHz. The sweep time was set to auto couple and the trace was allowed to stabilize before making the final measurement. By using the Peak marker function the maximum amplitude was determined. The final measurement takes into account the loss generated by all the involved cables (0.24 dB). Measurement uncertainty is +/- 1.1 dB. FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 23 of 47 Peak Power Spectral Density Operating Frequency Max PSD Limit Verdict Plot

[MHz]

[dBm]

[dBm]

[Pass/Fail]

2402 2440 2480

-11.8

-11.7

-11.6 8 8 8 Pass Pass Pass A B C Plot A P P Date: 6.MAY.2019 09:52:07 FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 24 of 47 Plot B Plot C Date: 6.MAY.2019 09:51:28Date: 6.MAY.2019 09:50:40 FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 25 of 47 5.1.4 Emissions in non-restricted bands RESULT: Pass Date of testing:

Requirements:

2019-05-06 FCC 15.205, FCC 15.209, FCC 15.247(d) and RSS-247 section 5.5 In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. Test procedure:

ANSI C63.10-2013 KDB 558074 D01 DTS Meas Guidance v05.02 Section 11.13 A RF conducted measurement was done using the marker-delta method, as described in ANSI C63.10. Measurements were performed using a spectrum analyzer with a suitable span to encompass the peak of the fundamental and using the following settings:

RBW = 100kHz, VBW = 300kHz. The highest emission amplitudes relative to the appropriate limit were measured and recorded in this report. Measurement uncertainty is +/- 2.5 dB. Results: All out of band spurious emissions are more than 20 dB below the fundamental. See the figures on the following pages. FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 26 of 47 Plot: Emissions in non restricted bands, Spectral Diagram @2402 MHz Plot: Emissions in non restricted bands, Spectral Diagram @2440 MHz Date: 6.MAY.2019 09:56:16Date: 6.MAY.2019 09:58:08 FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 27 of 47 Plot: Emissions in non restricted bands, Spectral Diagram @2480 MHz Date: 6.MAY.2019 10:00:20 FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 28 of 47 5.1.5 Band Edge Conducted Emissions RESULT: Pass Date of testing:

Requirements:

2019-07-03 FCC 15.205, FCC 15.209, FCC 15.247(d) and RSS-247 section 5.5 In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. Test procedure:

ANSI C63.10-2013 KDB 558074 D01 DTS Meas Guidance v05.02 A RF conducted measurement was done using the marker-delta method, as described in ANSI C63.10. Measurements were performed using a spectrum analyzer with a suitable span to encompass the peak of the fundamental and using the following settings:

RBW = 100kHz, VBW = 300kHz. The highest emission amplitudes relative to the appropriate limit were measured and recorded in this report. Measurement uncertainty is +/- 2.5 dB. Results: All out of band spurious emissions are more than 20 dB below the fundamental. See the figures on the following pages. FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 29 of 47 Plot: Band Edge Conducted Emission, Spectral Diagram, 2402 MHz, showing more than 20 dBc, F1 shows the band edge frequency of 2400 MHz. FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 30 of 47 Plot: Band Edge Conducted Emission, Spectral Diagram, 2480 MHz, showing more than 20 dBc. F1 shows the band edge frequency of 2483.5 MHz. FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 31 of 47 5.1.6 Radiated Spurious Emissions of Transmitter RESULT: PASS Date of testing:

Frequency range:

Requirements:

2019-05-21 30MHz - 25GHz FCC 15.209 and FCC 15.247(d) and RSS-Gen Radiated emissions which fall outside the operation frequency band and outside restricted bands shall either meet the limit specified in FCC 15.209(a) or be attenuated at least 20dB below the power level in the 100kHz bandwidth within the band that contains the highest level of the desired power (the less severe limit applies). Radiated emissions which fall in the restricted bands, as defined in FCC 15.205(a) and RSS-Gen Table 6, must comply with the radiated emission limits specified in FCC 15.209(a) and RSS-Gen Table 4. Test procedure:

ANSI C63.10-2013 KDB 558074 D01 DTS Meas Guidance v05.02 The EUT was placed on the testsite turntable. Before final measurements of radiated emissions were performed, the EUT was scanned to determine its emission spectrum profile. The physical arrangement of the test system, the associated cabling were varied in order to ensure that maximum emission amplitudes were attained. The spectrum was examined from 30MHz to the 10th harmonic of the highest fundamental transmitter frequency (25GHz). Final radiated emission measurements were made at 3m distance. At each frequency where a spurious emission was found, the EUT was rotated 360 and the antenna was raised and lowered from 1 to 4m in order to determine the emissions maximum level. Measurements were taken using both horizontal and vertical antenna polarizations. The highest emission amplitudes relative to the appropriate limit were recorded in this report. Field strength values of radiated emissions at frequencies not listed in the tables are more than 20 dB below the applicable limit. Where Peak (Pk) values where at least 6 dB under the Average (Av) limits, Av value was not tested. Were Average values were tested, Average values were measured using at least 10 kHz Video Bandwidth. FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 32 of 47 Radiated Emissions, 30MHz - 1GHz, Horizontal and Vertical Antenna Orientations Frequency

[MHz]

114.1 143.7 161.6 191.7 239.7 800-960 noise Antenna Orientation Level QP

[dBV/m]

Limit QP

[dBV/m]

Verdict

[Pass/Fail]

Vertical Vertical Horizontal Vertical Horizontal Vertical 23.4 21.5 18.4 33.5 25.0 28.0 43.5 43.5 43.5 43.5 46.0 46.0 Pass Pass Pass Pass Pass Pass Notes: - Level QP = Reading QP + Factor

- Tested in modes as described in section 4.2, the 6 highest values noted. Preliminary measurements indicated that the radiated emissions from EUT were not affected by the EUTs operating mode or frequency.

- Quasi Peak detector used with a bandwidth of 120 kHz.

- Measurement uncertainty is +/- 5.22 dB. Plot of the emissions (Peak detector values shown), EUT Horizontal-Antenna Horizontal @2402 MHz M1, M2 are from the AUX1 (test lab power supply) Date: 22.MAY.2019 08:25:12 FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 33 of 47 Plot of the emissions (Peak detector values shown), EUT Horizontal-Antenna Vertical @2402 MHz M1, M2 are from the AUX1 (test lab power supply) Plot of the emissions (Peak detector values shown), EUT Vertical-Antenna Vertical @2402 MHz M1, M2 are from the AUX1 (test lab power supply) Date: 22.MAY.2019 08:27:37Date: 22.MAY.2019 08:36:10 FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 34 of 47 Plot of the emissions (Peak detector values shown), EUT Vertical-Antenna Horizontal @2440 MHz M1, M2 are from the AUX1 (test lab power supply) Plot of the emissions (Peak detector values shown), EUT Vertical-Antenna Horizontal @2480 MHz M1, M2 are from the AUX1 (test lab power supply) Date: 22.MAY.2019 09:08:19Date: 22.MAY.2019 09:14:02 FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 35 of 47 Radiated Emissions, 1 - 25GHz, 2402 MHz. Frequency

[MHz]

1440 2275 2312.5*R

(restricted band 2310-2390) 2483.6*R

(restricted band 2483.5-2500) 4804*H 7206*H 9608*H EUT Detector Bandwidth Level Orientation/

Antenna Orientation

(MHz)

[dBV/m]

Limit

[dBV/m]

Result V / H V / H H / H V / H V / V V / V V / V Pk Pk Pk Pk Pk Pk Pk 1 1 1 1 1 1 1 38.5 48.5 49.6 50.0 54.8 Pk 53.1 Av 55.4 Pk 53.1 Av 53.0 Pk 48.6 Av 54 (Av) 74 (Pk) 54 (Av) 74 (Pk) 54 (Av) 74 (Pk) 54 (Av) 74 (Pk) 54 (Av) 74 (Pk) 54 (Av) 74 (Pk) 54 (Av) 74 (Pk) Pass Pass Pass Pass Pass Pass Pass Radiated Emissions, 1 - 25GHz, 2440 MHz. EUT Detector Bandwidth Level Limit Result Frequency

[MHz]

Orientation/

Antenna Orientation 1440 V / H 2312.5*R

(restricted band 2310-2390) 2483.6*R

(restricted band 2483.5-2500) 2568.5 4880*H 7320*H 9759*H 22391 H / H V / H H / H V / V V / V V / V V / V Pk Pk Pk Pk Pk Pk Pk Pk

(MHz)

[dBV/m]

[dBV/m]

40.1 49.6 50.0 52.2 53.6 Pk 53.6 Av 53.5 Pk 49.9 Av 52.0 Pk 46.6 Av 47.6 54 (Av) 74 (Pk) 54 (Av) 74 (Pk) 54 (Av) 74 (Pk) 54 (Av) 74 (Pk) 54 (Av) 74 (Pk) 54 (Av) 74 (Pk) 54 (Av) 74 (Pk) 54 (Av) 74 (Pk) Pass Pass Pass Pass Pass Pass Pass Pass 1 1 1 1 1 1 1 1 FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 36 of 47 Radiated Emissions, 1 - 25GHz, 2480 MHz. Frequency

[MHz]

1440.7 2339.5*R

(restricted band 2310-2390) 2483.55*R

(restricted band 2483.5-2500) 4960*H 7440*H 9919*H 12399 EUT Detector Bandwidth Orientation/

Antenna Orientation

(MHz) Level

[dBV/m]

Limit

[dBV/m]

Result V / H V / H V / H V / V V / V V / V V / V Pk Pk Pk Pk Pk Pk Pk 1 1 1 1 1 1 1 38.7 49.0 52.8 50.4 Pk 50.1 Av 54.4 Pk 49.9 Av 52.0 Pk 46.9 Av 47.5 54 (Av) 74 (Pk) 54 (Av) 74 (Pk) 54 (Av) 74 (Pk) 54 (Av) 74 (Pk) 54 (Av) 74 (Pk) 54 (Av) 74 (Pk) 54 (Av) 74 (Pk) Pass Pass Pass Pass Pass Pass Pass Notes:

- *R refers to a frequency in a restricted band,

- *H refers to a frequency which is a harmonic of the fundamental.

- Field strength values of radiated emissions not listed in the tables above are more than 20 dB below the applicable limit.

- Measurement uncertainty is +/- 5.5 dB.

- a selection of plots is provided on the next pages FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 37 of 47 Plots of the radiated emissions Plot of the emissions at 2402 MHz, EUT Vertical, Horizontal polarization, Peak values shown gap in the plot is of the used Notch filter Plot of the emissions at 2402 MHz, range 4 to 12 GHz, EUT Vertical, Vertical polarization, Peak values shown FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 38 of 47 Plot of the emissions at 2402 MHz, EUT Vertical, Vertical polarization, 4.8 GHz, Average value shown Plot of the emissions at 2402 MHz, EUT Horizontal, Horizontal polarization, 7.2 GHz, Average value shown FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 39 of 47 Plot of the emissions at 2402 MHz, EUT Vertical, Vertical polarization, 9.6 GHz, Average value shown Plot Radiated unwanted emissions in the restricted frequency band 2310 - 2390 MHz at 2402 MHz, reduced Video BW (worst case Average values, EUT Horizontal, Antenna Horizontal position shown). FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 40 of 47 Plot of the emissions at 2440 MHz, EUT Vertical, Horizontal polarization, Peak values shown, gap in the plot is of the used Notch filter Plot of the emissions at 2440 MHz, in the range 4 to 12 GHz, EUT Vertical, Vertical polarization, Peak values shown FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 41 of 47 Plot of the emissions at 2440 MHz, harmonic at 4880 GHz, Vertical polarization, Average values shown Plot of the emissions at 2440 MHz, in the range 12 to 18 GHz, EUT Vertical, Vertical polarization, Peak values shown, reduced video bandwidth. FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 42 of 47 Plot of the emissions at 2440 MHz, in the range 18 to 25 GHz, EUT Vertical, Vertical polarization, Peak values shown, reduced video bandwidth FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 43 of 47 Plot of the emissions at 2480 MHz, EUT Vertical, Horizontal polarization, Peak values shown, gap in the plot is of the used Notch filter Plot of the emissions at 2480 MHz, in the range 4 to 12 GHz, Vertical polarization, Peak values shown FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 44 of 47 Plot of the emissions at 2480 MHz, harmonic at 4960 GHz, EUT Vertical,Vertical polarization, Average values shown Plot of the emissions at 2480 MHz, harmonic at 7440 GHz, EUT Vertical,Vertical polarization, Average values shown FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 45 of 47 Plot of the emissions at 2480 MHz, harmonic at 9919 GHz, EUT Vertical,Vertical polarization, Average values shown Plot of the emissions at 2480 MHz, in the range 12 to 18 GHz, EUT Vertical, Vertical polarization, Peak values shown, reduced video bandwidth FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 46 of 47 Plot Radiated unwanted emissions in the range 18 25 GHz at 2480 MHz, reduced Video BW

(Peak values, Antenna Vertical position shown). Plot Radiated unwanted emissions in the restricted frequency band 2483.5 - 2500 MHz at 2480 MHz, reduced Video BW (worst case Average values, EUT Horizontal, Antenna Horizontal position shown). FCC ID: LCGVU121 IC: 2519A-VU121 Test Report No.:

19040102.r01 Page 47 of 47 5.2 AC Power Line Conducted Measurements RESULT: Not Applicable / Not requested by the applicant. Date of testing:

N/A End of report

Testing and certification of electronic and electric appliances, systems, installations and telecommunication systems PHOTOGRAPHS OF THE TESTSETUP OF A BRAND Endress+Hauser, MODEL VU121 Page 1 of 6 TV Rheinland Nederland B.V. Eiberkamp 10 9351VT Leek The Netherlands Telephone: +31 888887888 Internet: www.tuv.com/nl E-mail: products@nl.tuv.com Table of contents 1 PHOTOGRAPHS OF THE TEST SETUP. ...................................................................................................................... 3 1.1.1 1.1.2 1.1.3 1.1.4 1.1 RADIATED EMISSIONS..................................................................................................................................................... 3 Radiated emissions setup below 1 GHz. ......................................................................................................... 3 Radiated emissions setup above 1 GHz, up to 18 GHz. ............................................................................... 4 Radiated emissions setup above 1 GHz, 18 G up to 25 GHz ....................................................................... 4 Radiated emissions setup detail, front and rear side. .................................................................................... 5 ANTENNA PORT CONDUCTED TESTS ............................................................................................................................ 6 Conducted tests test setup overview ................................................................................................................ 6 1.2.1 1.2 Page 2 of 6 1 Photographs of the test setup. 1.1 Radiated emissions. 1.1.1 Radiated emissions setup below 1 GHz. Page 3 of 6 1.1.2 Radiated emissions setup above 1 GHz, up to 18 GHz. 1.1.3 Radiated emissions setup above 1 GHz, 18 G up to 25 GHz Page 4 of 6 1.1.4 Radiated emissions setup detail, front and rear side. Page 5 of 6 1.2 Antenna Port Conducted Tests 1.2.1 Conducted tests test setup overview END OF DOCUMENT Page 6 of 6