FCC and Industry Canada Compliance Information This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
this device may not cause harmful interference, AND this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Enlighted Inc. could void the user's authority to operate the equipment. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
l'appareil ne doit pas produire de brouillage, ET l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. CE This device complies with the essential requirements and other relevant requirements of the R&TTE Directive (1999/5/EC). The equipment is Class 1 radio equipment which can be placed on the market and be put into service without restrictions in accordance with article 1(3) of Commission Decision 2000/299/EC (Version July 2014). Model: SU-4S FCC ID: AQQ-SU4S IC: 10138A-SU4S Copyright 2016 Enlighted Inc. All rights reserved. All other brand or product names are trademarks of their respective companies or organizations. Technical Support For questions regarding the installation or operation of this product, contact Enlighted Technical Support: support@enlightedinc.com Company Contact Information Location: 930 Benecia Ave, Sunnyvale, CA 94085 Phone: +1.650.964.1094 Web: enlightedinc.com Ruggedized Sensor
(SU-4S) Installation Instructions Ruggedized Sensor (front and back) Applicable For:
SU-4S-LRW; SU-4S-LRB SU-4S-HRW; SU-4S-HRB Shipped Components Enlighted Ruggedized Sensor Unit inch Lock Nut Tools you may Need inch Knock out tool Items you will Need inch LB Conduit Body inch Chase Nipple Page 5 Page 6 93-01663-01 Rev01 Page 1 Caution Installation and maintenance must be performed by a qualified electrician in accordance with local, state, and national electrical codes (NEC) and requirements. Step 6: Knock out a inch hole on the end of the light fixture. Using the inch chase nipple, connect the LB conduit to the fixture. See Figure 5. Installation The Ruggedized sensor is shipped with the cable attached to the sensor. Figure 1. Chase Nipple LED Description LED Status Description/Solution LED not on Check power and wiring Purple solid All LEDs are on during boot time for 5-6 seconds Green blinking Sensor commissioned and working Figure 1 Step 1: Turn off all power to the light fixture by switching off the circuit breaker. Step 2: Mount the Control Unit (CU) in a UL approved enclosure. Refer to the Control Unit Installation Guide. See Figure 7 for detailed wiring connections from the CU. Step 3: Remove the cover plate of the inch LB conduit body by removing the two screws. Figure 2. Figure 2 Step 4: Thread the Ruggedized sensor onto LB conduit body. Figure 3. Figure 3 Enlighted Control Unit Red blinking Incompatibility between LED driver and sensor Replace LED driver and if not resolved, replace sensor. Red solid Faulty sensor replace sensor Green solid Sensor installed, initialized, and uncommissioned waiting for discovery. Figure 5 Blue solid Image being upgraded. Step 7: Pull the Ruggedized sensor cable through the chase nipple into the fixture and connect it to the Control Unit. See Figure 6. For wiring connections to the CU, see Figure 7. Enlighted Control Unit Figure 6 Figure 7 Step 5: Replace the cover and two screws on the LB conduit body. Figure 4. Step 8: If the ruggedized senor cable is not long enough to reach the Control Unit, use an RJ12 coupling to connect the rugged sensor cable to an Enlighted 7ft Sensor cable.
(CBL-2-7F) Step 9: Switch on the circuit breaker to turn the power on. Figure 4 Page 2 Page 3 Page 4