T30PA127F2.4G ZIGBEE PCB MODULE OEM/Integrators Installation Manual SECTION:HARDWARE August,2017 Technical support:tech.support@ennfus.com Sales:sales.international@ennfus.com MADE IN CHINA 0 ENNFU SCIENTIFIC REC 30128 REV A. Revision History Revision Number Revision A Date Released August,2017 Release Specifics First Release 1 ENNFU SCIENTIFIC REC 30128 REV A. COPYRIGHT 2017 ,ENNFU SCIENTIFIC COMPANY LIMITED This document is confidential and is the property of Ennfu Scientific Company Limited(Ennfu).It may not be copied or reproduced in any way without the express written consent of Ennfu.This document also is an unpublished work of Ennfu.Ennfu intends to,and is maintaining the work as confidential information.Ennfu also may seek to protect this work as an unpublished copyright.In the event of either inadvertent or deliberate publication,Ennfu intends to enforce its rights to this work under the copyright laws as a published work.Those having access to this work many not copy,use,or disclose the information in this work unless expressly authorized by Ennfu. Trademark and logo:
ENNFUis registered trademark of Ennfu Scientific Company Limited in China and/or other countries. The property of all other trademarks and names mentioned in this document belong to all registered companies. its legally General Ennfu may terminate your license if you fail to comply with the terms and conditions of this license.In such event,you must destroy your copies of the software program.You are responsible for payment of any taxes,including personal property taxes,resulting from this license. Occupation Safety and Health Act(OSHA) The occupation safety and health act clearly places the burden of compliance on the user of the equipment and the act is generalized to the extent that determination of compliance is a judgment decision on the part of the local inspection.Hence,Ennfu will not be responsible for meeting the full requirements of OSHA in respect to the equipment supplied or for any penalty assessed for failure to meet the requirements,in respect to the equipment supplied,of the Occupation Safety and Health Act,as interpreted by an authorized inspector.Ennfu will use their best efforts to remedy such violation at a reasonable cost to the buyer. Ennfu Warranty The seller agrees,represents and warrants that the equipment delivered hereunder shall be free from defects in material and workmanship.and the product quality warranty period is 12 months after delivery. Said warranty shall not apply if the equipment shall not have been operated in accordance with sellers written instructions applicable to such equipment,or if such equipment shall have been repaired or modified without sellers approval;provided,however,that the foregoing limitation of warranty insofar as it relates to repairs,alternations,or modifications,shall not be applicable to routine preventive and corrective maintenance which normally occur in the operation of the equipment. Declaimer Though the information provided herein is believed to be accurate,be advised that the information contained herein is not a guarantee for satisfactory results.Specifically,this information is neither a warranty nor guarantee,expressed or implied,regarding performance,merchantability,fitness,or any other matter with respect to the products,and recommendation for use of the product information in conflict with any patent.Please note that Ennfu reserves the rights to change and/or improve the product design and specification without notice. 2 ENNFU SCIENTIFIC REC 30128 REV A. Federal Communications Commission (FCC) statement FCC ID:2ANLK-T30A This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC rules.These limits are designed to provide reasonable protection against harmful installation.This module generates,uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions. interference residential in a However,there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the module and receiver.
-Connect the module into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. This module complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Radiation Exposure Statement This RF module complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment and its antenna should be installed and operated with minimum distance 20 cm between the radiator and your body. This module and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. Notice:
The module is limited to OEM installation ONLY. This module is intended for OEM integrators under the following conditions:
1. This module is restricted to installation in products for use only in mobile and fixed applications. 2. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. 3. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter. 4. OEM integrator has be limited the operation channels in channel 1-16 for 2.4GHz band. 3 ENNFU SCIENTIFIC REC 30128 REV A. The OEM integrator is still responsible for:
1. Ensuring that the end-user has no manual instructions to remove or install module 2. The FCC compliance requirement of the end product, which integrates this module. 3. Appropriate measurements (e.g. 15 B compliance) and if applicable additional equipment authorizations (e.g. Verification, Doc) of the host device to be addressed by the integrator/manufacturer. 4. The separate approval portable configurations with respect to Part 2.1093 and different antenna configurations is required for all other operating configurations, including The user manual of the end product should include:
1. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. 2. the restriction of operating this device in indoor could void the users authority to operate the equipment. 3. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. 4. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 5. The FCC part 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference received, including interference that may cause undesired operation. interference, and (2) this device must accept any Label of the end product:
The final end product must be labeled in a visible area with the following "Contains FCC ID:2ANLK-T30A ". The end product shall bear the following 15.19 statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. If the labeling area is considered too small and therefore it is impractical (smaller than the palm of the hand) to display the compliance statement, then the statement may be placed in the user manual or product packaging. Guidance to the Host Manufacturer:
1. We hereby acknowledge our responsibility to provide guidance to the host manufacturer in the event that they require assistance for ensuring compliance with the Part 15 Subpart B requirements. 2. The host manufacturer is responsible for additional testing to verify compliance as a composite system. When testing the host device for compliance with the Part 15 Subpart B requirements, the host manufacturer is required to show compliance with the Part 15 Subpart B while the transmitter module(s) are installed and operating. The modules should 4 ENNFU SCIENTIFIC REC 30128 REV A.
(i.e. be transmitting and the evaluation should confirm that the modules intentional emissions are compliant fundamental and out of band emissions) with the Radio essential requirements. The host manufacturer must verify that there are no additional unintentional emissions other than what is permitted in the Part 15 Subpart B or emissions are complaint with the Radio aspects. CE Conformity Hereby, Ennfu Scientific Company Limited declares that this device is in compliance with the essential safety requirements and other relevant provisions set out in the European Directive. EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013 Disposal and recycling this module properly according to local You must dispose of laws and regulations.Because this module contains electronic components,it must be disposed of separately from household waste.When this module reaches its end of life,contract local authorities to learn about disposal and recycling options. 5 ENNFU SCIENTIFIC REC 30128 REV A. Safety Instructions :
1, Static Electricity High frequency simulator has electrostatic sensitive characteristics, avoid human contact the electronic components of module as much as possible.(According to the production process of official anti-static standard of IC manufacturers 2, Soldering Soldering iron needs good grounding during the soldering, and the cable ground-strap should be equipped during the mass production. 3, Power supply Power quality has great influence on the performance of the module, please ensure that the power module has small ripple, be sure to avoid the frequent greatly shake.Recommend using type filter (ceramic capacitor / tantalum capacitor and inductance). 4, Grounding Module should be single point grounding,recommend to apply for 0 ohm, or 10mH inductor, separate from other grounding of circuit. 5, Antenna module installation requirement The antenna module installation structure has a great influence on the performance of the module, so must make sure the antenna exposed and vertical. When the module mounted in a shell, can use high-quality antenna to extend the line and extended to the external of casing. The antenna should not being mounted in the shell,that will greatly shorten the transmission distance. 6, Interference If there are other frequency wireless modules in the same module, should has a reasonable frequency planning layout, taking shielding measures to reduce harmonic interference and inter-modulation interference effects. 7, Crystals If there are existing crystals near this module in the circuit board,please increase the distance between the non crystals as much as possible. 6 ENNFU SCIENTIFIC REC 30128 REV A. About this manual This manual provides the hardware information you need to design.read this manual before working with this product.For personal and safety and for the best product performance,make sure you thoroughly understand the contents before using this module. If You Need Assistance All technical support is given in the attached CD.For more information or any requests,please send an E-mail request to tech.support@ennfus.com, and should enter your contact information, we will give you full related needed technical supports. 7 ENNFU SCIENTIFIC REC 30128 REV A. 1, INTRODUCTION T30PA127F2.4G is a 2.4GHz wireless tiny volume Zigbee wireless pcb module,SMD mode
(1.27mm pin spacing ), and it s a transceiver module. Nordic RTF 2401 PA chip being adopted to get a chargeable power and get a longer distance when designed.the module was also being with external IPEX antenna terminal.
(T30PA127F2.4G ZIGBEE PCB MODULE OUTLINE) T30PA127F2.4G module has being used the vector network analyzer for precise impedance matching,and now it has stable production,suit for various applications(especially for Smart Home applications). T30PA127F2.4G module based on the TI CC 2530 RF chip technology,which had integrated 8051 microprocessor and wireless transceiver,apply to all the Zigbee design and 2.4GHz IEEE802.15.4 protocol. The module had being derived all I/O ports of Single-Chip to easily develop many applications. As an advanced hardware platform,the module has two types for selection:
- Preprogramming type, P/N T30PA127F2.4G/P
- No programming type, P/N T30PA127F2.4G/N For the preprogramming type, the developer just need to operate few configurations to quickly build a Zigbee network in 5 minutes,and never need any complicate programming.all the details please see the software manual. For no programming type,the developer should do a second developing for its own applications. 8 ENNFU SCIENTIFIC REC 30128 REV A. 2,TECHNICAL PARAMETERS No. Parameter name RF chip PA chip Module size Module weight Work frequency Craft Interface mode Power supply Comm level Value CC2530 RFX2401 TI NORDIC Summary 1.7mg 2400~2483.5MHz Immersion gold 14.9mm*25.9mm*2.7mm Including IPEX Including IPEX 2.4GHz IEEE 802.15.4 PROTOCOL SMD,SIMMERSION GOLD,LEAD FREE SMD Caution:Causing permanent damage to the module when Higher than 3.6vdc. 2.0~3.6V DC 3*8*1.27mm
+0.7~+5V Test condition:
Weather:Sunny,35;relative humidity:65%;
Test location:Open wide space Antenna gain:3DB Installation height:2m Speed rate:250k About 100mW MCU sleepwireless shut,voltage 3.3V Power supply must exceed 100mA Average current All I/O pins of MCU,please see IC manual. Single data packet Single data packet Please see IC manual. External antenna Actual test comm distance About 800m 250Kbps 20dBm 1.2uA 140mA@20dBm 42mA I/O 1~103 Bytes 1~103 Bytes Support IPEX Air ratio Send power Shut current Send current Receive current Comm interface Send length Receive length RSSI support Antenna interface Working temperature Working humidity Storage temperature Receive sensitivities
-40~+85 Industrial Grade 10%~90%
-40~+125 97dBm@250Kbps Relative humidity,Non-condensing. Industrial Grade Please see IC manual. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 9 ENNFU SCIENTIFIC REC 30128 REV A. 3, PIN DEFINE MIN 14.9 25.9 2.7 0.8 1.27 3.1 2.3. MAX 14.9 25.9 2.7 0.8 1.27 3.1 2.3 A B C D E F G Units mm mm mm mm mm mm mm 10 ENNFU SCIENTIFIC REC 30128 REV A. Pin Definition Pin No. Pin name Pin direction Pin application 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 GND VCC P2.2 P2.1 P2.0 P1.7 P1.6 NC NC P1.5 P1.4 P1.3 P1.2 P1.1 P1.0 P0.7 P0.6 P0.5 P0.4 P0.3 P0.2 P0.1 P0.0 RSET 1~103BYTE GROUND,TO THE GROUNDING OF POWER SUPPLY. SUPPORT POWER SUPPLY,MUST BE 2.0~3.6V I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O CHIP IO CHIP IO CHIP IO CHIP IO CHIP IO NC NC CHIP IO CHIP IO CHIP IO CHIP IO CHIP IO CHIP IO CHIP IO CHIP IO CHIP IO CHIP IO CHIP IO CHIP IO CHIP IO CHIP IO INPUT RESET PORT The Pin definition,driver software and communication protocol of Modular,please see TI
<CC2530 DataSheet>. 11 ENNFU SCIENTIFIC REC 30128 REV A. 4PACKAGE SPECIFICATION 4.1 Tape reel package Tape Reel Package Information Module numbers Total module number Reel size Package number 194 modules/reel 776 pcs/reel 13/44 750 pcs/reel 12 ENNFU SCIENTIFIC REC 30128 REV A. T30PA127F2.4G Tape reel layout 4.2 Carton Package information:
Package Material Carton Carton Package Size(mm) L360*W360*H55 L460*W370*H370 Gross Net(Kg) Remark 1.90 11.90 Product package Transport package 13 ENNFU SCIENTIFIC REC 30128 REV A. 5,Inspection Inspect the packages for external damage before opening.after unpacking,inspect the unit for damage and compare parts to those and the shipping packing list. 6,Storage The package can be safely stored indoors,with hole plugs installed,between-50 and
+85 degree C.The package must be protected against moisture. 14 ENNFU SCIENTIFIC REC 30128 REV A.