iEm rsonT EAM-9002 At a Glance Receiver Professional System Microphone Dual Wireless 2. Mic A LED 3. Power LED 4. Mic BLED Instruction Manual use and keep fofuturereference before Please read carefully 1 Power switch (On, Off)
Thank You when it comes to We know you have many choices technology; thank you for choosing Electronics. fornia, entertain we are dedicated and delight. us here at Naxa 1 in 2001 in Los Angeles, Cali that products to delivering Established Audio output jack (1/4") 2. Power (AC 110V,60Hz) We trust that you will be happy with your purchase. Please read this manual carefully erence. tation, Come visit us at www.emersonaudio.com all that we have to offer!
You may also find the latest FAQ, documen and other product material at our website. and see and save it for ref Microphones In the Box Two wireless
(A/green, B/red) microphones Wireless receiver Microphone patch cable (1/4" to 1/4") 1 1 e I I I
1 1 1
1.Microphone pickup 2. PowerLED 3. Power switch (On, Standby, Off) 4. Battery compartment cap Pagel Emerson Electronics I www.emerson audio.com How to Connect To start using your wireless er must be connected fier, karaoke, or PA system. microphones, to the audio input of an ampli the receiv When using a microphone for vocal or speech work, the closer you are to the microphone when record more likely ing. Consider speaker and the microphone. placing a pop filter between the it will pick up "plosives"
the Your receiver can be connected to systems with:
1/4 input 1/8" input (with an optional adapter To connect the receiver and microphones:
Specifications Sensitivity
-72 dB Frequency 9Ppedance 50-18,000 Hz 6000 Operation voltage Microphone:
DC 9 V 110 V60Hz Receiver: AC 1. Use the patch cable to connect the 1/4 AUDIO OUTPUT jack of the receiver of the input system (e.g., PA system). an amplifier, karaoke, to the 1/4" connector or Battery life 2.Connect the receiver extend the antennas timal reception. to power (AC 110 V). Fully and position them for op Effective distance Type Up to 3 hours 30FT Cardioid 3 one "9V" battery the battery compartment, twist and require microphones The wireless each. To access unscrew the bottom cap of the microphone. Load one "9V" alkaline into the compartment, and then screw the bottom cap
@ Makesure tomatch the+and-
battery back into place. polarities compartment. marked inside the battery 4.Turn the receiver on, and then turn the micro phones on. When the microphones to the receiver, green and red, respectively. the A and B indicators will light are connected e gre en A LED corr:esponds to the
(D Th _ _ marked with a green band;
microphone the red B LED corresponds crophone marked with a red band. to the mi are subject to change without prior notice Specifications FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. turning input level on the input sys Lower the tem before Slowly readjust able level after the microphones turned on and connected. the input to a comfort are on the microphones. Placing Your Microphone The optimal position the sound source depends on a few factors, mostly a matter of trial and error. relative to but it is for your microphone with different Experiment see which sounds best, but keep in mind. distances and positions to things the following Cardioid Cardioid microphones that are in front ofit. Sounds from behind the micro phone will are more sensitive be slightly muted to sounds Support If you have problems the instructions the web at www.emersonaudio.com to get up to them for your device. inute news, alerts, and documentation in this manual. Please also visit us on with your device, please consult For additional hnical Suppot. assistance, please contact Emerson Tee NAXA Technical 2320 East 49th St. Vernon, CA 900S8 Support Cardioid microphones speech recording. are great for vocal or www.naxa.com/n axa_support Page2 Emerson Electronics I www.emersonaudio.com