iEm rson EAM-9001 How to Connect Wireless Microphone To start using your microphone, put of a speaker system or amplifler. connect it to the in Your microphone can be connected to systems with:
System 1/4" input 1/8" input (with the included adapter}
Wired Connection 1 Connect the XLR end of the cable to the bottom of the microphone. 2. Connect the 1/4" end of the cable to a speak 1/8" plug er system input {or use the included adapter). 3. Set the switch on the microphone position. to the "MIC"
Instruction before use and keep for future Manual read carefully reference. Please Thank You We know you have many choices when it comes to technology;
thank you for choosing us here at Naxa Electronics. Established fornia, we are dedicated Cali in 2001 in Los Angeles, that to delivering products entertain and delight. We trust that you will be happy with your purchase. Please read this manual carefully and save it for ref erence. You may also find the latest FAQ, documen i and other product material at our website. tation, Come visit us at www.emersonaudio.com and see all that we hav e to offer!
Wireless 1 Load one "AA" battery ment found on the back of the wireless Connection compart receiver. into the battery In the Box Microphone Wireless receiver Cable (1/4" to XLR) 1/4" to 1/8" adapter Page 1 ta Make sure to match the polarity marked inside the battery compart ment. 2. Turn the wireless tenna. receiver on and extend its an 3. to Connect the 1/4" plug of the wireless 1/8"
a speaker system input (or use the included plug adapter). receiver Cardioid speech recording. microphones are great for vocal or for vocal or speech When using a microphone work, the closer you are to the microphone it will pick up "plosives"
more likely ing. Consider speaker and the microphone. the when record placing a pop filter between the Specifications Frequency 50-18,000 Hz Output impedance Operation voltage DC 1.SV Effective distance 30FT 4. Twist and unscrew the bottom half of the mi crophone clockwise to reveal the battery com partment. Load one "AA" battery into phone, then screw the bottom back on. the micro Cable length lu Adapter plug 5.03 m (16.5') 6.3 mm (1/4") 3.5 mm (1/8") CD Disconnect the cable from the micro phone before opening the microphone. Failure phone. to do so will damage the micro this product. at www.emersonaudio.com. for the latest visit information. may change to improve Specifications and design Please our website product FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Make sure to match the polarity marked inside the battery compart ment. 5. Set the switch on the microphone position. to the ON l-
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. for your microphone Your Microphone Placing The optimal position the sound source depends on a few factors, mostly a matter of trial and error. Experiment see which sounds best, but keep the following things in mind. relative to but it is with different distances and positions Support If you have problems the instructions to get up to the m the web at www.emersonaudio.com for your device. inute news, alerts, in this manual. Please also visit us on and documentation with your device, to please consult For additional assistance, hnical Support. please contact Emerson Tee Cardioid Cardioid that are in front of it. Sounds from behind the micro muted. phone will be slightly are more sensitive microphones to sounds Support NAXA Technical 2320 East 49th St. Vernon, CA 90058 www.naxa.com/naxa_support Emerson Electronics I www.emersonaudio.com Page2 Emerson Electronics I www.emersonaudio.com