FCC ID: S4A99-990120-00 RF/IR Remote Control

Universal Remote Control URC PLUS (v3) Users Guide V2.3 for URC Plus v3.8 COPYRIGHT 2009 Entone, Inc. All rights reserved. This document contains proprietary information protected by copyright. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written consent of Entone, Inc., 2755 Campus Drive, Suite 235, San Mateo, CA 94403. U.S.A. DISCLAIMER IF THIS PRODUCT DIRECTS YOU TO COPY MATERIALS, YOU MUST HAVE PERMISSION FROM THE COPYRIGHT OWNER OF THE MATERIALS TO AVOID VIOLATING THE LAW WHICH COULD RESULT IN DAMAGES OR OTHER REMEDIES. TRADEMARKS Entone and the tagline Connecting the Home are trademarks of Entone, Inc. All other trademarks or registered trademarks belong to their respective owners. CHANGES The material in this document is for information only and is subject to change without notice. While reasonable efforts have been made in the preparation of this document to assure its accuracy, Entone, Inc. assumes no liability resulting from the use of the information contained herein. Entone, Inc. reserves the right to make changes in the product design without reservation and without notification to its users. P/N: HYDRA_UG 1.0 CUSTOMER SUPPORT AND CONTACT INFORMATION For Customer Support please call: 650.572.7000 Customer Contact Information:

Entone, Inc. 2755 Campus Drive Suite 235 San Mateo, CA 94403 U.S.A. Tel: 650.572.7000 www.entone.com V2.3 for URC Plus v3.8 Table of Contents FCC Information...................................................................................................................................................................3 Introduction ...............................................................................................................................................................4 1.1 Loading Batteries..............................................................................................................................................................5 2.1 Controlling the Hydra................................................................................................................................................6 Attach the RF Remote Control Antenna..........................................................................................................................7 URC PLUS Registration with Hydra ................................................................................................................................8 URC PLUS Registration with Hydra having URC PLUS logo........................................................................................9 URC PLUS Registration with Hydra without URC PLUS logo.................................................................................... 11 3.1 Controlling the Amulet ........................................................................................................................................... 12 IR Reception Range ...................................................................................................................................................... 13 4.1 Controlling Your Television and other A/V Devices.............................................................................................. 14 To Program a TV or AUX device .................................................................................................................................. 15 Toggle Power Key Punch-through Functionality.......................................................................................................... 16 Auto Search Procedures ............................................................................................................................................... 16 Appendix A Device Code............................................................................................................................................... 17 Appendix B Other Features........................................................................................................................................... 22 Showing URC PLUS Firmware Version....................................................................................................................... 22 Showing Programmed Device Code ............................................................................................................................ 23 2 Copyright 2009 Entone, Inc. All rights reserved V2.3 for URC Plus v3.8 URC PLUS Users Guide FCC Information FCC ID S4A99-990120-00 3 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. Caution any changes or modifications not expressly approved by Entone Incorporated could void the user's authority to operate this equipment. Copyright 2009 Entone, Inc. All rights reserved. V2.3 for URC Plus v3.8 URC PLUS Users Guide Chapter 1.1 Introduction The Entone Universal Remote Control Plus (URC PLUS) is designed to work either on Radio Signals (RF) or InfraRed

(IR). It can control Hydra Multi-Television Gateway using RF from another room where is not at direct sight distance from the Hydra. Or, it can use IR to control Amulet Video Receiver at direct sight distance. The URC PLUS can also be used to control other A/V devices such as TV, DVD player and audio equipment using IR. The URC PLUS differs from the old URC on the followings :

 The old URC can only support old Hydra hardware. URC PLUS supports both the old Hydra and new Hydra hardware (with URC PLUS logo printed on the front panel).

 URC PLUS supports Amulet

 URC PLUS supports more A/V devices 4 Copyright 2009 Entone, Inc. All rights reserved. V2.3 for URC Plus v3.8 URC PLUS Users Guide Loading Batteries The URC PLUS comes with AA-size batteries, which need to be installed when you first receive your system. When you replace old batteries, you should replace all of the batteries. Use batteries of the same kind, for example alkaline or carbon zinc, and do not mix batteries of different kinds. Alkaline batteries last longer than carbon zinc. Warning: Mixing old and new batteries or different types of batteries poses a fire hazard. To load batteries to URC PLUS:

1. Press down on the battery covers top latch and slide the cover off. 2. 3. Put the new batteries in. Make sure you match the plus ( + ) ends with the plus markings on the battery If you are changing out batteries, take out all of the old batteries. case. 4. Slide the cover back into place. Figure 1-1 Loading Batteries to URC PLUS 5 Copyright 2009 Entone, Inc. All rights reserved. V2.3 for URC Plus v3.8 URC PLUS Users Guide Chapter 2.1 Controlling the Hydra Hydra is a multi-television gateway. It can support multiple TVs in multiple rooms viewing different channels or TV programs. You can use URC PLUS to control Hydra using radio signals (RF). These radio signals travel over long distances and go though walls and other solid objects. You must connect the RF Remote Control Antenna to the rear panel of the Hydra. Your Hydra comes with 3 URC PLUS. (Additional URC PLUS can be purchased separately.) Your URC PLUS must be registered to one of the 3 decoders before it can be used. One URC PLUS can only be registered to one decoder. However, you can register at most 3 URC PLUS to a decoder. After registration, you need to use the corresponding URC PLUS to control the decoders. Figure 2-1 Controlling Hydra using RF URC PLUS 6 Copyright 2009 Entone, Inc. All rights reserved. V2.3 for URC Plus v3.8 URC PLUS Users Guide Here are some principles of the remote registration method:

 Each decoder allows a maximum of 3 URC PLUS to be registered and a registration list is maintained. If the user has registered 3 URC PLUS and tries to register another URC PLUS, the first registered URC PLUS will be removed from the registration list. This works as a first-in-first-out fashion.

 Each URC PLUS can only be registered for one decoder. If user tries to register a URC PLUS which is already registered to another decoder, that remote registration will be removed from the original registration list.

 The registration list is maintained in order. If the secondly registered URC PLUS is removed from the list, the third entry will move forth to the second and the third will be blank for a new URC PLUS to be registered. You must install the RF Remote Control antenna before doing the registration. Please refer to the previous section for installing the RF Remote Control Antenna. Attach the RF Remote Control Antenna You need to attach the RF Remote Control Antenna to the Hydras rear panel REMOTE ANTENNA input in order to use the radio control remotes. Figure 2-2 Attaching RF Remote Control Antenna NOTE: Be sure to set the antenna straight up so that you can use the URC PLUS from as far away as possible. Dont let the antenna touch anything. ATTENTION: If your URC PLUS isnt working very well from far away, you may be experiencing interference from objects near your receiver. To improve your URC PLUSs reception range, try any or all of the followings:

1. Place the receiver higher than all of the other equipment in your entertainment center. 2. Provide room above the receiver so that the antenna can be installed straight up. If this is not possible, 3. Place the RF antenna outside the entertainment center by using a coaxial cable to connect the antenna tilt the RF Antenna at about a 30 angle. to the Hydra. 4. Try moving the Hydra to other locations. 7 Copyright 2009 Entone, Inc. All rights reserved. V2.3 for URC Plus v3.8 URC PLUS Users Guide URC PLUS Registration with Hydra There are 2 types of Hydra boxes, the new one with the URC PLUS logo on top of the front panel and the old one without the URC PLUS logo. The registration method for the new box and the old box is different. Figure 2-3 URC PLUS Logo Figure 2-4 New Hydra with URC PLUS logo The following table lists the new and old Hydra box type :

New Hydra with URC PLUS logo Old Hydra without URC PLUS logo Hydra HD B Series, Amulet HD Hydra II, Hydra HD A Series Check your Hydra box type and use the corresponding registration method. 8 Copyright 2009 Entone, Inc. All rights reserved. V2.3 for URC Plus v3.8 URC PLUS Users Guide URC PLUS Registration with Hydra having URC PLUS logo 1. Press and hold the OK button on the Hydra front panel for approx. 5 seconds. When releasing the OK button, the Hydra front panel will display RC REG. The Hydra is now in remote registration mode. Figure 2-5 Hydra in Remote Registration Mode 2. On the URC PLUS, press and hold the STB button for approx. 5 seconds. The STB button backlight will illuminate. Figure 2-6 URC PLUS in Remote Registration Mode Step 1 (for box with URC PLUS logo) On the URC PLUS, press STB once again. Both the STB and AUX button backlight will illuminate. Figure 2-7 URC PLUS in Remote Registration Mode Step 2 (for box with URC PLUS logo) Figure 2-8 URC PLUS in Remote Registration Mode Step 3 (for box with URC PLUS logo) Now the URC PLUS is in registration mode. 9 Copyright 2009 Entone, Inc. All rights reserved. V2.3 for URC Plus v3.8 URC PLUS Users Guide 3. Select the decoder to register by:

 Press 1 to register URC PLUS to decoder 1.

 Press 2 to register URC PLUS to decoder 2.

 Press 3 to register URC PLUS to decoder 3. After you enter a registration event, the STB button backlight on the URC PLUS will blink twice to indicate that the registration process was successful. The Hydra front panel will display RC REG Dx to indicate that the registration process was successful. Figure 2-9 Remote Registration Successful Pressing a key other than 0, 1, 2, 3 or a button is not pressed within 10 seconds, the STB backlight will extinguish and the URC PLUS registration process will be terminated. If the Hydra does not receive any URC PLUS registration event within 30 seconds, the process will be terminated. 4. The Hydra front panel displays the following messages during remote control registration:

Front Panel Message RC REG TO RC REGERR RC REG RC REGEND RC REG D1 RC REG D2 RC REG D3 Description Registration times out Registration error In registration mode Registered to IR only mode Registered to decoder 1 Registered to decoder 2 Registered to decoder 3 Table 2-1 Remote Registration Messages NOTE:

 While the URC PLUS is in STB mode, the volume +/- and MUTE key signal will be sent to the TV.

 By Default, if the URC PLUS is in STB mode, the POWER key signal will be sent to the STB ONLY.

 If the URC PLUS is in TV mode, the POWER key signal will be sent to the TV ONLY.

 However, the POWER key can be configured to control both the STB and TV while the URC PLUS is in STB mode, please refer to the section Toggle Power Key Punch Through Functionality in Chapter 4 for details. 10 Copyright 2009 Entone, Inc. All rights reserved. V2.3 for URC Plus v3.8 URC PLUS Users Guide URC PLUS Registration with Hydra without URC PLUS logo 1. Press and hold the OK button on the Hydra front panel for about 5 seconds. When the OK button is released, the Hydra front panel Standby/On indicator blinks twice (alternates red and green), then stays lit red to indicate that the Hydra is now in remote registration mode. Figure 2-8 Hydra in Remote Registration Mode 2. On the URC PLUS, press and hold the STB button for approx. 5 seconds. The STB button backlight will illuminate. Now the URC PLUS is in registration mode. Figure 2-9 URC PLUS in Remote Registration Mode (for box without URC PLUS logo) 3. Select the decoder to register by:

 Press 1 to register URC PLUS to decoder 1.

 Press 2 to register URC PLUS to decoder 2.

 Press 3 to register URC PLUS to decoder 3. After you enter a registration event, the STB button backlight on the URC PLUS and the Hydra front panel Standby/On indicator will blink twice to indicate that the registration process was successful. 4. Pressing a key other than 0, 1, 2, 3 or a button is not pressed within 10 seconds, the STB backlight will extinguish and the URC PLUS registration process will be terminated. If the Hydra does not receive any URC PLUS registration event within 30 seconds, the process will be terminated. NOTE:

 While the URC PLUS is in STB mode, the volume +/- and MUTE key signal will be sent to the TV.

 By Default, if the URC PLUS is in STB mode, the POWER key signal will be sent to the STB ONLY.

 If the URC PLUS is in TV mode, the POWER key signal will be sent to the TV ONLY.

 However, the POWER key can be configured to control both the STB and TV while the URC PLUS is in STB mode, please refer to the section Toggle Power Key Punch Through Functionality in Chapter 4 for details. Copyright 2009 Entone, Inc. All rights reserved. V2.3 for URC Plus v3.8 11 URC PLUS Users Guide Chapter 3.1 Controlling the Amulet Amulet is a single television video receiver. You can connect Amulet to a primary TV only. Amulet only uses InfraRed (IR) to receive remote control signals. Unlike Hydra, you do not need to do remote registration in order to use URC PLUS to control Amulet. However, you have to program the URC PLUS to use IR. To set the URC PLUS to use IR to control Amulet:

1. On the URC PLUS, press and hold the STB button for approx. 5 seconds. The STB button backlight will illuminate. Now the URC PLUS is in registration mode. Figure 3-1 URC PLUS in Remote Registration Mode Step 1 (for Amulet using IR mode) 2. On the URC PLUS, press STB once again. Both the STB and AUX button backlight will illuminate. Figure 3-2 URC PLUS in Remote Registration Mode Step 2 (for Amulet using IR mode) Figure 3-3 URC PLUS in Remote Registration Mode Step 3 (for Amulet using IR mode) 12 Copyright 2009 Entone, Inc. All rights reserved. V2.3 for URC Plus v3.8 URC PLUS Users Guide 3. Press 0 to set URC PLUS to IR mode only. The URC PLUS will not send any RF signal. The STB button backlight on the URC PLUS will blink twice to indicate that the setting was successful. Pressing a key other than 0, 1, 2, 3 or a button is not pressed within 10 seconds, the STB backlight will extinguish and the URC PLUS registration process will be terminated. IR Reception Range IR signals travel only short distances (40 feet or less), and cannot go through walls or other solid objects. You must point the URC PLUS to the Amulet, with no objects blocking the line of sight. Figure 3-4 IR Reception Range 13 Copyright 2009 Entone, Inc. All rights reserved. V2.3 for URC Plus v3.8 URC PLUS Users Guide Chapter 4.1 Controlling Your Television and other A/V Devices The URC PLUS can also be used to control TVs and other A/V devices such as DVD players and recorders. The URC PLUS uses InfraRed (IR) light signals to control other devices that the remote is programmed to control. IR signals travel only short distances (40 feet or less), and cannot go through walls or other solid objects. You must point the URC PLUS directly at these devices, with no objects blocking the line of sight. Figure 4-1 Controlling Devices using IR URC PLUS You can program URC PLUS to control one TV and one AUX device. Use the remote controls mode keys

(i.e., STB, TV, or AUX) to control a specific device. When pressed, the selected mode key will light up confirming your choice. Then you can use the URC PLUS to control your STB, TV or AUX device. You have to program the URC PLUS what TV and AUX devices you are using by either 1) entering the 4-

digit device code 2) doing an auto search. NOTE:

 While the URC PLUS is in STB mode, the volume +/- and MUTE key signal will be sent to the TV.

 By Default, if the URC PLUS is in STB mode, the POWER key signal will be sent to the STB ONLY.

 If the URC PLUS is in TV mode, the POWER key signal will be sent to the TV ONLY.

 However, the POWER key can be configured to control both the STB and TV while the URC PLUS is in STB mode, please refer to the section Toggle Power Key Punch Through Functionality in Chapter 4 for details. Copyright 2009 Entone, Inc. All rights reserved. V2.3 for URC Plus v3.8 14 URC PLUS Users Guide To Program a TV or AUX device 1. Locate the device code for your desired device in the device code table provided in the Appendix. If you could not find the device code for your device or it does not work after trying the listed device codes for your device brand, then you can go to the next section to try the auto search procedures. 2. Turn on your device and with media inserted (if applicable). 3. On the remote control, press a device mode key once (i.e., TV or AUX). Figure 4-2 Select the device mode NOTE: Use the AUX mode key to program control of VCR, DVD player, cable box, satellite set-top-

box and audio device. 4. Press and hold the Setup key until the selected mode key backlight blinks twice, then release Setup. The device mode key will light up. Figure 4-3 Press SETUP for 5 seconds to enter device setup mode 5. Enter the four-digit device code for you device. If you perform this procedure correctly, the selected device mode key backlight will blink twice. NOTE: If you enter an invalid device code, the selected device mode key will fast blink 7 times. Device program mode will be terminated. 6. Aim the remote control at your device and press the Power once. The device should be turn off. If it does not respond, repeat the above steps. Copyright 2009 Entone, Inc. All rights reserved. V2.3 for URC Plus v3.8 15 URC PLUS Users Guide Toggle Power Key Punch-through Functionality By default, if the remote control is in STB mode, the URC Power button switches STB off ONLY. To control the URC Power button functionality to switch off either both the TV and/or STB, do the following:

1. On the remote control, press STB once to ensure it is in STB mode. 2. Press and hold the Setup key until the STB mode key backlight blinks twice, then release Setup. The STB device mode key backlight will light up. 3. Press POWER key once. 4. Either do the following:

a. Press 1 to control both the STB and TV, OR b. Press 0 to control the STB ONLY Auto Search Procedures If your device does not respond to the remote control after trying all devices codes listed for you brand, or if your brand is not listed at all, try searching for your device code as follows:

1. Turn on your TV or your A/V device. 2. On the remote control, press a device mode key once (i.e., TV or AUX). NOTE: Use the AUX mode key to program control of VCR, DVD player, cable box, satellite set-top-box and audio device. 3. Press and hold the Setup key until the selected device mode key blinks twice, then release Setup. The device mode key will light up. 4. Press the POWER key once. 5. Aim the remote control at the TV. Press either the CHANNEL UP key or CHANNEL DOWN key to do device auto-scan:

a. Press the CHANNEL UP key to start searching upward at an approx. 5 seconds interval for each device code. The TV/AUX mode key will be on and blink every 5 seconds while in the device scan mode. NOTE: In this search mode, the remote control will send IR codes from the library starting from the lowest code set number to the end of code set for that device; OR b. Press the CHANNEL DOWN key to start searching downward at an approx. 5 seconds interval for each code set. The TV mode key will be on and blink every 5 seconds while in the device scan mode. NOTE: In this search mode, the remote control will send IR codes from the highest code set number to the beginning of code set of that device. If the TV turns off, a working code has been found. Press OK once to lock in the code. The selected mode key will blink twice If all code sets of that device is exhausted in the search and the OK is not pressed, the selected device key will fast blink 7 times and the search mode will be terminated. NOTE: During the auto-scan, you can press UP arrow or DOWN arrow to advance to the next device code immediately without waiting for 5 seconds. You can also use UP arrow or DOWN arrow to change the direction of the search. 6. 7. 16 Copyright 2009 Entone, Inc. All rights reserved. V2.3 for URC Plus v3.8 Your URC Plus can control many brands and models of television, VCR, DVD and other types of audio-visual equipment. The following pages list device codes for many categories and brands of equipment. You may need to test several codes to find the best match for your equipment. Your equipment may be supported even if your brand is not shown in the list below. If you cannot locate your brand, or none of the listed device codes works, then you may still use the Auto-Search feature to try to locate a suitable device code. Instructions for using the Auto-Search feature is located on page 15 of this guide. URC PLUS Users Guide Appendix A Device Code TV Admiral Adventura Aiwa Akai Albatron Alleron America Action Amtron Anam Anam National AOC Apex Audiovox Aventura Bang & Olufsen Belcor Bell & Howell Benq Bradford Brillian Brockwood Broksonic Candle Carnivale Carver CCE Celebrity Celera Changhong Citizen Clarion Coby Colortyme Concerto 0001, 0020 0012 0071 0002, 0018, 0053 0013 0009 0023 0008 0023 0003, 0008 0004, 0005, 0006, 0018, 0080 0021, 0025, 0041 0008, 0023 0022 0031 0004 0001 0015, 0083 0008, 0023 0028 0004 0023, 0075 0004, 0006, 0012, 0018 0018 0019 0029 0002 0025 0025 0004, 0006, 0008, 0018 0023 0076 0004, 0006 0004, 0006 17 0023 0007, 0008 0008, 0023 0019 0008, 0023 0082 0000, 0004, 0006, 0018, 0019, 0020, 0053 0008, 0023 0085 0004, 0005, 0006, 0043 0004, 0006 0065 0032 0000 0004, 0011, 0017 0016, 0022, 0023, 0045 0020 0002 0026 0002, 0003, 0004, 0006 0004, 0006, 0007, 0008, 0009, 0022, 0023, 0043 0004, 0006, 0018 0081 0022 0009 0008, 0009, 0022, 0023 0008, 0023 0026, 0027 0000, 0003, 0004, 0006, 0010, 0034, 0037, 0061 0004, 0011, 0017, 0018 0004, 0005, 0006, 0007, 0018 0087 0008, 0009, 0023 Contec Contec/Cony Craig Crosley Crown CTX Curtis Mathes CXC Cytron Daewoo Daytron Dell DiamondVision Dimensia Dumont Durabrand Dwin Electroband Electrograph Electrohome Emerson Envision Epson ESA Fujitsu Funai Futuretech Gateway GE Gibralter Goldstar Gradiente Grunpy Haier Hallmark Harman/Kardon Harvard Havermy Hewlett Packard Hisense Hitachi Hyundai IMA Infinity Insignia Inteq Janeil JBL JC Penney JCB Jensen JVC Kawasho KEC Kenwood KLH Kloss Novabeam KTV LG Logik Luxman LXI Magnavox Majestic Marantz Matsushita Maxent 0016, 0030 0004, 0006 0019 0008, 0023 0020 0072 0091 0004, 0006, 0007 0014 0008 0019 0045, 0084 0017 0012 0019 0000, 0004, 0005, 0006, 0010 0002 0004, 0006 0007, 0010, 0067 0002, 0004, 0006 0023 0004, 0006, 0018 0025 0008, 0012 0008, 0018, 0023, 0029 0004, 0005, 0013 0001 0004, 0006 0000, 0006, 0019, 0021 0004, 0006, 0018, 0019, 0038, 0040, 0059, 0064, 0065 0001 0004, 0006, 0018, 0019, 0040 0024 0026 Copyright 2009 Entone, Inc. All rights reserved. V2.3 for URC Plus v3.8 URC PLUS Users Guide Megapower 0013 Megatron 0006 Memorex 0001, 0005, 0006, 0063 MGA 0004, 0005, 0006, 0018 Midland 0010, 0011, 0017 Mitsubishi 0004, 0005, 0006, 0020 Monivision 0013 Montgomery Ward 0001 Motorola MTC Multitech NAD NEC Net-TV Nikko Norcent Olevia Onwa Optimus Optonica Orion Panasonic Penney Philco 0003, 0020 0004, 0005, 0006, 0018 0008, 0023, 0029 0006, 0021 0003, 0004, 0005, 0006, 0018 0026 0006, 0018 0080 0073, 0079 0008, 0023 0024 0020 0045 0003, 0010, 0024, 0035, 0047 0018, 0021 0003, 0004, 0005, 0006, 0007, 0018, 0019 0003, 0004, 0007, 0019, 0038, 0040, 0065 0038 0004, 0018 0004, 0006 0025, 0077 0004, 0005, 0006 0086 0013 0010 0000 0004, 0006, 0007 0074 0090 0004, 0011, 0017 0003, 0010, 0024 0018, 0023 0000, 0004, 0006, 0007, 0008 0000, 0003, 0004, 0005, 0006, 0033, 0037, 0044, 0057 0018, 0023 0011, 0017, 0018 0004, 0006, 0018, 0026 0004, 0005, 0006, 0007, 0018, 0029, 0042, 0053, 0054 0045 0004, 0070 Philips Philips Magnavox Pilot Pioneer Polaroid Portland Prima Princeton Prism Proscan Proton Protron Proview Pulsar Quasar Radio Shack Radio Shack/Realistic RCA Realistic Runco Sampo Samsung Sansui Sanyo 18 Scotch Scott Sears Sharp Sheng Chia Shogun Signature Sony Soundesign Squareview SSS Starlite Superscan Supre-Macy Supreme SVA Sylvania Symphonic Syntax Syntax-Brillian Tandy Tatung Technics Techwood Teknika Telefunken TMK TNCi Toshiba Vector Research Vidikron Vidtech Viewsonic Viking Vizio Wards Waycon Westinghouse White Westinghouse Yamaha Zenith 0006 0004, 0006, 0007, 0008, 0009, 0023 0000, 0004, 0006, 0009, 0019, 0021, 0022 0004, 0006, 0007, 0020, 0055 0020 0004 0001 0002, 0036, 0039, 0050, 0051, 0052, 0056 0004, 0006, 0008, 0009, 0023 0022 0004, 0008, 0023 0008, 0023 0020 0012 0002 0030 0004, 0006, 0018, 0019, 0022 0008, 0022, 0023, 0063 0073 0073 0020 0003, 0027 0010, 0024 0004, 0006, 0010 0001, 0004, 0005, 0006, 0007, 0008, 0009, 0019, 0023 0053 0004, 0006 0017 0021, 0046, 0048, 0049, 0058, 0060, 0062, 0066 0018 0019 0004, 0005, 0006 0026, 0078 0012 0027, 0089 0000, 0001, 0004, 0005, 0006, 0009, 0018, 0019 0021 0069 0043 0004, 0005, 0006, 0018 0001, 0004, 0011, 0017 DVD Accurian Advent Aiwa Akai Alco Allegro Amphion MediaWorks AMW Apex Arrgo Aspire Audiovox Bang & Olufsen Blaupunkt Blue Parade Broksonic California Audio Labs CineVision Coby Curtis Mathes CyberHome Daewoo Denon Disney Durabrand Emerson Enterprise ESA Fisher Funai GE Go Video Gradiente Greenhill Harman/Kardon Hitachi Hiteker Initial Insignia Integra JBL JVC Kawasaki Kenwood KLH Koss Landel 2027 2006 2074 2000 2004 2022 2085 2085 2013, 2014, 2031, 2059 2023 2007 2004 2016 2014 2012 2000, 2069 2002 2022 2060 2024 2023, 2029 2022, 2066 2002, 2056, 2073 2062 2025 2001, 2017, 2026 2017 2026 2018 2026 2011, 2014, 2063 2022, 2067 2002 2014 2019, 2077 2046 2013 2014, 2049 2026, 2084 2012 2019 2048 2004 2002, 2076 2004, 2014 2003, 2009, 2070 2028 Copyright 2009 Entone, Inc. All rights reserved. V2.3 for URC Plus v3.8 URC PLUS Users Guide Lasonic Lenoxx LG Liquid Video Liteon Magnavox Memorex Microsoft Mintek Mitsubishi Nesa Next Base Onkyo Oppo Oritron Panasonic Philips Pioneer Polaroid Proceed Proscan Qwestar RCA Regent Rio Rowa Samsung Sansui Sanyo Sharp Shinsonic Sonic Blue Sony Superscan Sylvania Teac Technics Theta Digital Toshiba Urban Concepts US Logic Venturer Xbox Yamaha Zenith 19 2020 2008, 2025 2017, 2022, 2064, 2082 2009 2027, 2071 2001, 2010, 2026, 2057 2000, 2062 2011 2014, 2021 2065 2014 2028 2010 2015 2003, 2009 2002, 2010, 2034, 2036, 2053, 2056, 2079, 2080, 2081 2010, 2057 2012, 2051, 2083 2043 2013 2011, 2055 2003 2004, 2011, 2012, 2014, 2038, 2055 2008 2022 2005 2002, 2039, 2041, 2046, 2050, 2052, 2058, 2067, 2078 2000 2000, 2018 2068 2021 2022 2032, 2033, 2037, 2042, 2044, 2045, 2047, 2054, 2075 2001 2001, 2026 2004 2002 2012 2000, 2010, 2030, 2035, 2040, 2061, 2072 2010 2021 2004 2011 2002, 2034 2010, 2017, 2022, 2064 VCR 1008 ABS 1005 Adventura 1005 Aiwa 1008 Alienware 1004 American High 1002 Asha 1000 Audio Dynamics 1003 Audiovox 1002 Beaumark 1001 Bell & Howell 1003 Calix 1002, 1003 Candle 1004 Canon 1002, 1003 Citizen 1000 Colortyme 1002, 1003 Craig 1000, 1002, 1004 Curtis Mathes 1002 Cybernex 1008 CyberPower 1005 Daewoo 1000 DBX 1008 Dell 1007 DIRECTV 1009 Durabrand 1005 Dynatech 1003 Electrohome 1003 Electrophonic 1003, 1004, 1005 Emerson 1001 Fisher 1004 Fuji 1005 Funai 1005 Garrard 1008 Gateway 1002, 1004 GE 1000, 1003 Goldstar 1005 Gradiente 1005 Harley Davidson 1000 Harman/Kardon 1001 Headquarter 1008 Hewlett Packard 1007 HNS Howard Computers 1008 1008 HP Hughes Network 1007 Systems 1007 Humax 1008 Hush 1008 iBUYPOWER 1004 Instant Replay 1000, 1001, 1002, 1003, JC Penney 1004 1004 JCL JVC Kenwood Kodak LG Linksys Lloyd's LXI Magnavox Magnin Marantz Marta Matsushita Media Center PC MEI Memorex MGN Technology Microsoft Mind Mitsubishi Motorola MTC Multitech NEC Nikko Niveus Media Noblex Northgate Olympus Optimus Orion Panasonic Philco Philips Philips Magnavox Pilot Pulsar Quarter Quartz Quasar Radio Shack Radio Shack/Realistic Radix Randex RCA Realistic ReplayTV Ricavision Runco Samsung Sanky Sansui Sanyo 1000, 1001, 1014 1000, 1001 1003, 1004 1003 1008 1005 1003 1004, 1009, 1016 1003 1000, 1001, 1004 1003 1004 1008 1004 1001, 1002, 1003, 1004, 1005, 1009, 1010 1002 1008 1008 1015 1004 1002 1002, 1005 1000, 1001 1003 1008 1002 1008 1004 1003 1010, 1018 1004, 1006, 1012 1004 1004, 1007, 1016 1016 1003 1009 1001 1001 1004 1003 1001, 1002, 1003, 1004, 1005 1003 1003 1002, 1004, 1007, 1011 1001, 1002, 1003, 1004, 1005 1006 1008 1009 1002, 1007 1009 1010, 1018 1001, 1002 Copyright 2009 Entone, Inc. All rights reserved. V2.3 for URC Plus v3.8 URC PLUS Users Guide Sears Sharp Shogun Singer Sonic Blue Sony Stack STS Sylvania Symphonic Systemax Tagar Systems Tandy Tashiko Teac Technics Teknika Tivo TMK Toshiba Totevision Touch Unitech Vector Research Video Concepts Videosonic Viewsonic Voodoo Wards XR-1000 Yamaha Zenith ZT Group Cable Box ABC Americast Antronix Archer AT&T Bell South Cable Vision Cabletenna Cableview Clearmaster ClearMax Colour Voice Comcast Comtronics Contec 20 1001, 1003, 1004 1017 1002 1004 1006 1008, 1013 1008 1004 1004, 1005 1005 1008 1008 1001 1003 1005 1004 1003, 1004, 1005 1007 1002 1008, 1019 1002, 1003 1008 1002 1000 1000 1002 1008 1008 1002, 1003, 1004, 1005 1004, 1005 1000, 1001 1009 1008 3000, 3001, 3002, 3004, 3024, 3025 3033 3006, 3007 3007 3041 3033 3036 3006 3005 3032 3032 3009 3037, 3038 3010 3011 3032 3039 3031 3012 3026 3030 3007 3000, 3001 3013, 3026 3027 3014, 3015 3001 3026 3001, 3013, 3024, 3026, 3029, 3031 3016 3017, 3025 3029, 3031, 3038, 3039, 3041 3018 3032 3003 3042 3018 3011 3028 3021, 3023, 3025 3025 3008, 3009, 3016 3019, 3027, 3035 Coolmax COX Director Eastern Everquest Focus GC Electronics GE Gemini General Instrument 3001, 3029, 3031, 3037 Goldstar Hamlin Hitachi Jasco Jerrold Magnavox Memorex Motorola Movie Time Multitech NEC NET Brazil NSC Oak Pace Panasonic Paragon Philips Pioneer Popular Mechanics 3030 Proscan Pulsar Quasar Radio Shack RCA Realistic Recoton Regal Regency Rembrandt Runco Samsung Scientific Atlanta Signal Signature Sony Sprucer Standard Component Starcom Stargate Starquest Supercable 3000, 3001 3025 3025 3026, 3032 3005, 3023 3007 3030 3015 3012 3001 3025 3019, 3027 3004, 3041 3013, 3026 3001 3034, 3036 3023 3020 3013, 3024, 3026 3013, 3026 3013, 3026 3029 3032 3040 3002 3025 3032 3013, 3026 3018 3006, 3007 3024 3006, 3007 3032 3011, 3016, 3018 3032 3032 3032 3022, 3025, 3033 3030 Supermax TIME WARNER Tocom Toshiba Tristar Tusa TV86 Unika United Cable Universal V2 View Star Viewmaster Vision Vortex View Zenith Zentek Satellite Alphastar CaptiveWorks Chaparral Coolsat DIRECTV Dish Network 4010 4053 4004 4054 4013, 4015, 4016, 4019, 4021, 4022, 4028, 4029, 4031, 4035, 4036, 4041, 4042, 4043, 4046, 4047 4000, 4001, 4002, 4003, 4014, 4020, 4023, 4033, 4044, 4045 4000, 4014 4005 4000, 4014, 4033, 4044, 4045 4000 Dishpro Drake Echostar Expressvu General Instrument 4006, 4017 GOI Hisense Hitachi HTS Hughes Network Systems Humax Ilo Jerrold JVC LG Magnavox Memorex Mitsubishi Motorola Next Level Panasonic 4000 4018 4011 4000 4013, 4019, 4022, 4024, 4041 4055 4018 4017 4000, 4033, 4044, 4045 4048 4016 4016 4022 4017 4017 4043, 4047, 4049 Copyright 2009 Entone, Inc. All rights reserved. V2.3 for URC Plus v3.8 URC PLUS Users Guide Pansat Paysat Philips Pioneer Primestar Proton Radio Shack RCA Realistic Samsung Sharp Sony Star Choice STS Tivo Toshiba UltimateTV Uniden US Digital USDTV Viewsat Voom Zenith 4051 4016 4013, 4016, 4024, 4031, 4042 4013 4009 4018 4017 4024, 4025, 4026, 4028, 4029, 4030, 4034 4007 4013, 4024, 4036, 4038 4050 4015, 4021, 4027, 4032, 4035, 4037, 4039, 4040 4017 4012 4013, 4024 4041 4015 4008, 4016 4018 4018 4052 4017 4046 Audio ADC Adcom Aiwa Alco Amphion Media Works AMW Anam Apex Audiotronic Audiovox B & K Bang & Olufsen BOSE Capetronic Carver Coby Curtis Mathes Denon Fisher GE GPX Harman/Kardon Hitachi Integra JVC Kenwood KLH Koss Left Coast Magnavox Marantz Mitsubishi 5005 5067 5055 5011 5012 5012 5007 5064 5008 5011, 5063 5068 5017 5028, 5046 5005 5008 5059 5001 5052, 5053, 5054 5013 5000 5065 5002, 5060 5013 5004 5056 5009, 5031 5011 5010 5002 5005, 5008, 5033 5002, 5008 5062 NAD Nakamichi NEC Onkyo Optimus Oritron Panasonic Philips Pioneer Polk Audio RCA Rio Samsung Sanyo Sharp Sherwood Shure Sonic Blue Sony Soundesign Stereophonics Sunfire Teac Technics Thorens Venturer Wards Yamaha 5016 5015 5003 5034, 5037, 5038, 5045, 5049, 5051 5001, 5005, 5006, 5007 5010 5027, 5035, 5047 5002, 5008, 5061 5001, 5005, 5006, 5021, 5026, 5029 5002 5001, 5005, 5006, 5007, 5011, 5057 5014 5041 5013 5066 5058 5003 5014 5018, 5019, 5020, 5022, 5023, 5024, 5025, 5030, 5032, 5042, 5043 5000 5006 5009 5007, 5011 5044 5008 5011 5000 5004, 5036, 5040, 5048, 5050 21 Copyright 2009 Entone, Inc. All rights reserved. V2.3 for URC Plus v3.8 URC PLUS Users Guide Appendix B Other Features Showing URC PLUS Firmware Version The URC PLUS firmware version is in the format of x.y.z, where x, y and z is digit 0-9. Use the following procedures to show the URC PLUS firmware version:

1. Press STB. 2. Press and hold SETUP for 5 seconds. 3. The STB backlight will illuminate. 4. Press INFO once. 5. The 3 digits of the firmware version (x, y and z as described above) will be displayed in the following manner. a. The STB backlight blinks to indicate the digit. One blink indicates 1, 2 blinks indicates 2, etc until 9 blinks indicates 9. A 0 is indicates by a shot, long, short, long, short, long blink. In between each digit, the STB backlight will be off for 1 second. b. c. For example, the following blink pattern shows a firmware version of 2.0.4. .-.-.- .... In addition, the URC PLUS Firmware version will also be shown on the sticker at the back of the remote control. 22 Copyright 2009 Entone, Inc. All rights reserved. V2.3 for URC Plus v3.8 URC PLUS Users Guide Showing Programmed Device Code You can display the 4-digit device code by the following procedures:

1. Press TV to display the TV device code or AUX to display the AUX device code. 2. Press and hold SETUP for 5 seconds. 3. The TV or AUX backlight will illuminate. 4. Press INFO once. 5. The 4-digits device code will be displayed in the following manner. a. The TV/AUX backlight blinks to indicate the digit. One blink indicates 1, 2 blinks indicates 2, etc until 9 blinks indicates 9. A 0 is indicates by a shot, long, short, long, short, long blink. b. In between each digit, the TV/AUX backlight will be off for 1 second. c. For example, the following blink pattern shows a device code of 0123. -.-.- . .. ... 23 Copyright 2009 Entone, Inc. All rights reserved. V2.3 for URC Plus v3.8

entone connecting the home October 21, 2009 To whom it may concern:

We the undersigned, hereby authorize Atlas Compliance & Engineering, Inc., to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Atlas Compliance & Engineering, Inc., on our behalf shall have the same affect as acts of our own. This authorization is valid until further written notice from Entone Technologies (HK) Limited. Sincerely, Mark Evensen Vice President Entone Technologies (HK) Limited 23/F, Langham Place, 8Argyle St, Hong Kong www.entone.com tel +852 3148 3500 fax +852 3148 3588

entone connecting the home October 21, 2009 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen:

This letter is to comply with Section 0.457(d)(2)(i) and Section 0.459 pertaining to confidential material. Entone Technologies (HK) Limited would like the following documents regarding this submission for FCC ID: S4A99-990120-00 to be kept confidential. 1) 2) Electrical Schematics of the Circuitry Block Diagram and Theory of Operation The above material contains trade secrets or technical data, which would customarily be guarded from competitors. We do not want these documents to be accessible to the general public. Sincerely, Mark Evensen Vice President Entone Technologies (HK) Limited Entone Technologies (HK) Limited 23/F, Langham Place, 8Argyle St, Hong Kong www.entone.com tel +852 3148 3500 fax +852 3148 3588

Non-Conformities FCC ID: S4A99-990120-00 (CKC CS Ref # E09-000137-FCC-01) The items listed below represent requests for information following review of this application for certification under United States (FCC) regulations. Further question may arise pending review of responses to these items. OK Non-Conformity or Comment Submitted Response ID

#

x x 1 2 CKC CS General Agreement has not yet been provided. Please provide a signed copy of the CKC CS General Agreement. The FRN information provided on form 731 is inconsistent with that listed on the FCC website. Please submit any changes in FRN information to the FCC. 10/8/09 The Inconsitancy is in the FRN Number information not the Grantee Information. A signed Copy was provided. The address which appears on the FCC website is as follows Entone Technologies Limited 17F 10 Knutsford Terrace Tsimshatsui Hong Kong This is the information I submitted on the 731 form to the TCB. Line 1: 17F 10 Knutsford Terrace Line 2:

P.O. Box:

City: Tsimshatsui State: Country: Hong Kong Zip Code: N/A where is the inconsistency I spoke with the Entone and the FRN Information was updated on 07/30/2008. The information on file for the FRN Number (23/F Office Tower Langham Place) is correct. Can you update the information on the 731? I will have the Grantee Code information updated on the FCC web Respondent / Date of Response Bruce Smith 10/5/09 Bruce Smith 10/6/09 Bruce Smith 10/8/09 Continued Below 10/8/09 The Information on the form 731 was updated. Still waiting on the Grantee Code Information to be updated. 10/16/09 Checked the FCC Website and the Grantee Information has not been updated yet. The Applicants Phone Number and Fax Number were not provided. We will contact the Agent, Technical & Non-Technical Contact before we would contact the applicant. This information is needed for filing. Please provide the aforementioned numbers. 10/8/09 - Update has not been made. Please either provide the numbers to us and we will update your information for you or enter the information under the category of Applicants & Manufacturers under the section Predefine and Manage on the left hand scroll bar . The confidentiality letter is signed by a party other than the person named in the FCCs grantee information listing. Please update either the grantee information, the confidentiality letter, or provide a letter from the person named on the grantee code information granting authority to the other individual permission to sign on their behalf. This requirement comes from the FCCs authorized individual policy contained in KDB publications. 10/8/09 New Letter has not been received. Please send the letter referenced. 10/20/09 The Grantee Contact was still shown as Mark Evensen and the Cover Letters Provided were signed by Carson Cheng. Please modify confidentiality letter to include citing to rule section 0.457 10/8/09 Draft Confidentiality letter is attached for your reference. site by my client and send this information to you at that time. My client has submitted the update to the FCC. Grantee Information was found to be updated on the Web. this will be updated Corrected on application form. the FCC website states Mark Evenson as the contact, I will get a new confidentiality letter corrected and signed by Mark. I will have the Grantee Code information updated on the FCC web site by my client and send this information to you at that time. New Cover Letter and Confidentiality Letter Provided. Do you have a template for a confidentiality letter? If so can you email it to me?

New Confidentiality Letter Provided. Bruce Smith 10/16/09 Bruce Smith 10/20/09 Bruce Smith 10/6/09 Bruce Smith 10/8/09 Bruce Smith 10/6/09 Bruce Smith 10/8/09 Bruce Smith 10/22/09 Bruce Smith 10/6/09 Bruce Smith x x 3 4 x 5 6 7 The block diagram contains a portion of the schematic diagram. Since the schematics have been referenced as confidential. Additionally, the operational description may be held confidential. Presently, the block diagram exhibit is not covered under the confidentiality letter, if so desired, please modify the confidentiality letter. (no response necessary to this item). 10/8/09 New Letter has not been received. Please send the letter referenced. I will change the confidentiality letter to include block diagram. New Confidentiality Letter Provided. 10/22/09 Bruce Smith 10/6/09 Bruce Smith 10/22/09 x The items indicated above must be submitted before processing can continue on the referenced application. Failure to provide the requested information within 60 days may result in application dismissal pursuant to Section 2.917(c) and forfeiture of the filing fee pursuant to Section 1.1106. How to read the table:

OK column indicates closure by CKC CS. ID column is for use with Agents to assist in identifying the probable source for closure. A Application issue TL Test lab issue C Client issue R Retesting may be necessary

# column indicates unique or separate non-conformity items (note some items may be related). Non-Conformity or Comment column indicates the evaluators specific question or comment. Submitted response column indicates the response or a summary of the response provided. Respondent / Date of Response column indicates the responding party or agent and the date of the response was either received or logged.