FCC ID: GDI-SID004 Supplies ID

Entrust Corporation 4/27/23 Element Project TS-DTCD-0004 Modular Integration Instructions Dear Application Examiner, We, Entrust Corporation hereby declare that the Supplies ID radio transmitter GDI-SID004 complies with the considerations provided in the sections below. 1. General a. The Supplies ID radio transmitter GDI-SID004 will only be integrated into Entrust Corporation products and is therefore controlled exclusively by Entrust Corporation. b. No manual exists for installation of this transmitter since Entrust is the integrator; however, the end product manual will include the FCC regulator notice that is described in section 8 below. 2. List of applicable FCC rules a. The applicable rules for this transmitter are the following:

i. 15.212 Modular transmitters ii. 15.203 Antenna requirement iii. 15.204 External radio frequency power amplifiers and antenna modifications iv. 15.225 Operation within the band 13.110-14.101 MHz 3. Summarize the specific operational use conditions a. This transmitter is only for use in Entrust host products that are within the scope of this limited modular approval (GDI-SID004). b. EMC Compliance Notice: To ensure compliance of the model RX10 retransfer printer to the radiated emissions requirements for class A Information Technology Equipment, be sure to use a shielded Ethernet cable when connecting to your network. 4. Limited module procedures a. The info below is also found in the FCC Modular Approval Letter exhibit, but is also provided here:

Entrust Corporation, Supplies ID, GDI-SID004 is seeking modular approval. The radio meets the requirements for modular approval as detailed in FCC 15.212. Compliance to each of the requirements is described below:

i. The modular transmitter must have its own RF shielding. The radio portion of the module is contained in its own RF shielding. The shielding is installed at the factory. Please see the Internal Photos exhibit. ii. The modular transmitter must have buffered modulation/data inputs. The EUT has buffered data inputs to ensure compliance with part 15 requirements under conditions of excessive data rates or over-

modulation. Please see the Schematics exhibit. iii. The modular transmitter must have its own power supply regulation. The EUT has its own power supply regulation to ensure compliance with Part 15 requirements regardless of the quality or level of external DC supplying the module from the host unit. Please see Schematics exhibit. Also, the technical report exhibit contains AC power line conducted emissions data taken with the EUT powered from a linear power supply that contains no EMC suppression components. iv. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204. The EUT meets the FCC antenna requirements. Please see Antenna information exhibit and internal photos exhibit. v. The modular transmitter must be tested in a stand-alone configuration. The EUT was tested in a stand-alone configuration. The module was greater than 10cm from the host device. Please see setup photos exhibit and technical report exhibit. vi. The modular transmitter must be labelled with its own FCC ID number. The EUT is labelled with its own FCC ID number. Please see FCC ID label & location exhibit. If the FCC ID number will not be visible when the module is installed inside a host device, another label with the FCC ID will be applied to the exterior of the host device. vii. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. The EUT is compliant with all applicable FCC rules. Detailed instructions for maintaining compliance are given in the user manual. viii. The modular transmitter must comply with any applicable RF exposure 5. Trace antenna designs requirements. See section 6 below. a. Transmitter is 13.54MHz and uses a circular PCB loop antenna with 4 turns, and a diameter of 46mm. 6. RF exposure considerations a. This device is for use with a minimum separation distance of 20cm between the antenna and the body, in a general / uncontrolled environment. 7. Antennas a. See section 5 above for details on the PCB trace antenna. 8. Label and compliance information a. The following FCC regulatory notice will be integrated into the end product manuals. 9. Information on test modes and additional testing requirements a. Operational modes and conditions were considered when creating and executing the test plan for the transmitter. The transmitter was operated in the appropriate mode for each test (such as continuous transmit, inactive, etc). These special test modes are not available to the operator; the equipment under test was manually configured to be in a certain test mode, and the test reports describe the mode(s) used for each test. 10. Additional testing, Part 15 Subpart B disclaimer a. See section 8 above for information on the regulatory notice that is included with the products that contain this transmitter. b. The manufacturer is required to ensure that the final host product that contains this limited modular device complies with Part 15 Subpart B through compliance testing. c. Entrust Corporation is ensuring compliance with FCC regulations by ensuring that any new type of host product that integrates this limited modular transmitter is tested and certified with a class II permissive change. Sincerely, Jeff Aymond Sr Electrical Engineer

DatacardGroup Datacard Group Minnetonka, MN 55343-9015 SECURE ID AND CARD PERSONALIZATION SOLUTIONS Tel. 952.933.1223 Fax 952.933.7971 www.datacard.com June 30, 2004 TCB TUV America Inc 10040 Mesa Rim Road San Diego CA 92121 Dear Sir or Madam:

We, DataCard Corporation [11111Bren Road West, Minnetonka, MN 55343], hereby deciare that the Supplies ID radio transmitter GDI-SIDO04 will only be integrated into Datacard products and is therefore controlled exclusively by Datacard Corporation. No manual exists for this product since DataCard is the integrator; however, the foliowing FCC regulatory notices will be integrated into the end product manuals. This equipment generates, uses, and can radiate radio frequency energy. If it is not installed and used in accordance with this instruction manual, it may interfere with radio communications. This equipment has been tested and found to be within the limits for Class A computing devices, pursuant to Title 47 CFR Part 15 Subpart B of FCC rules, designed to provide reasonable protection against radio interference in a commercial environment. Operation of this equipment in a residential environment may possibly cause interference. in the event of interference, the users, at their own expense, will be required to take whatever measures are necessary to correct the problem. This device emits radio-frequency waves and must be used as installed and recommended by Datacard, the device manufacturer. You may not modify the device or how it is used without the written permission of Datacard. You may not operate the device after modifying it or its method of operation. This device contains the following radio transmitter FCC ID: GDI-SID004. Sincerely, ick Hokanson Senior Agency Engineer 952 988 1384 952 988 1568 rick_hokanson@datacard.com

Entrust Corporation 9/13/22 Element Project TS-DTCD-0004 Label and Location (FCC) The label on the module states the FCC ID number, and all required statements are included in the compliance documentation that ships with the product, are shown below. Also shown is the location of the label on the module. This label is attached to the module as a permanent adhesive, attached to a metal plate. In addition to this label which is on the RFID module, the FCC ID number is also located on the label of end product that contains the module; an example is shown below which indicates that the FCC ID is contained within the product (also a permanent adhesive attached to metal plate). Note that some details may differ in this label but it will always include the FCC ID as shown.

EntrustCorporation 7/18/22 ElementProjectTSDTCD0004 AgentAuthorizationLetter Towhomitmayconcern, We,theundersigned,herebyauthorizeJeffAymondtoactonourbehalf,asouragent,inthe followingmattersrelatedtotheFCCand/orIndustryCanadaapprovalofourproducts:report submittal,relatedcorrespondence,thesigningofalldocumentsrelatingtothesematters,and anyotherlawfulactivitynecessarytoobtainsuchcertification.AnyactcarriedoutbyJeff Aymondwithinthescopeofthisauthorizationshallhavethesameeffectasourown. Thisauthorizationshallexpire12monthsfromoriginaldate. Sincerely, MarkForster PrincipalProductSafetyComplianceSpecialist

Date: 2/20/23 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 Re: Attestation regarding covered equipment and the Covered List FCC ID: GDI-SID004 To whom it may concern, Per 2.911(d)(5)(i), Jeff Aymond certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Per 2.911(d)(5)(ii), Jeff Aymond certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Sincerely, Jeff Aymond Principal Electrical Engineer

Entrust Corporation 4/3/23 Element Project TS-DTCD-0004 Cover Letter for FCC Application Description of radio:

Supplies ID radio is an RFID tag reader. 13.56MHz radio communicates with a passive RFID tag

(read & write) located on a nearby consumable supply component to determine proper identification and status. FCC ID is GDI-SID004, original filing in 2004, and a C2PC was completed in 2010. This is a C2PC where the limited modular radio is being implemented into several new versions of the product that are very similar to the existing product but have differences in mechanical parts and ancillary electrical equipment (not the limited modular radio). There are no mechanical, electrical, or firmware changes to the limited modular radio or the block diagram;

the board has not changed and it is still implemented in the same way. The new versions of the product are tested in the following versions of the product:

MX Series, LC Conversion, Phase 1 MX Series, LC Conversion, Phase 2 MX Series, LC Conversion, Phase 3.1 Specifically, the components that the limited modular radio is being integrated into are Cleaner

(phase 1), Graphics (phase 2), and Topper (phase 3.1). The radio circuit is located on PWA p/n 534508, and no changes have been made to this board since the last C2PC completed in 2010. This C2PC does not make any changes to any circuits of the following areas as listed in FCC 2.1043(a): frequency determining, frequency stabilizing, frequency multiplication, and basic modulator circuitry. The grounding and circuits are electrically identical to the circuits in the 2010 C2PC. An alternate manufacturer is being added to the crystal resonator component that generates the 13.56MHz carrier frequency for the antenna:

-The part on the bill of materials is Y2.

-Adding an alternate component that can be used in place of the existing part

-Both components are equivalent in specification for form / fit / function

-Additional testing was performed in DTCD0091 to qualify this crystal and verify that this crystal meets the performance requirements of the applicable standards. Applicable rule parts are FCC 15.225. FCC ID GDI-SID004 Sincerely, Jeff Aymond Sr Electrical Engineer

Entrust Corporation 7/18/22 Element Project TS-DTCD-0004 Modular Approval Letter Dear Application Examiner, Entrust Corporation, Supplies ID, GDI-SID004 is seeking modular approval. The radio meets the requirements for modular approval as detailed in FCC 15.212. Compliance to each of the requirements is described below:

1. The modular transmitter must have its own RF shielding. The radio portion of the module is contained in its own RF shielding. The shielding is installed at the factory. Please see the Internal Photos exhibit. 2. The modular transmitter must have buffered modulation/data inputs. The EUT has buffered data inputs to ensure compliance with part 15 requirements under conditions of excessive data rates or over-modulation. Please see the Schematics exhibit. 3. The modular transmitter must have its own power supply regulation. The EUT has its own power supply regulation to ensure compliance with Part 15 requirements regardless of the quality or level of external DC supplying the module from the host unit. Please see Schematics exhibit. Also, the technical report exhibit contains AC power line conducted emissions data taken with the EUT powered from a linear power supply that contains no EMC suppression components. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204. The EUT meets the FCC antenna requirements. Please see Antenna information exhibit and internal photos exhibit. 5. The modular transmitter must be tested in a stand-alone configuration. The EUT was tested in a stand-alone configuration. The module was greater than 10cm from the host device. Please see setup photos exhibit and technical report exhibit. 6. The modular transmitter must be labelled with its own FCC ID number. The EUT is labelled with its own FCC ID number. Please see FCC ID label & location exhibit. If the FCC ID number will not be visible when the module is installed inside a host device, another label with the FCC ID will be applied to the exterior of the host device. 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. The EUT is compliant with all applicable FCC rules. Detailed instructions for maintaining compliance are given in the user manual. 8. The modular transmitter must comply with any applicable RF exposure requirements. The EUT is compliant with all applicable RF exposure requirements. Please see RF Exposure Exhibit. Please contact me if you have additional questions. You attention to this matter is greatly appreciated. Best regards, Jeff Aymond Sr Electrical Engineer

Entrust Corporation 7/18/22 Element Project TS-DTCD-0004 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 Re: Request for confidentiality FCC ID: GDI-SID004 To whom it may concern, We hereby respectfully request that under the provision of 47 CFR 0.459 and 0.457(d) the documents listed below and attached with this application for certification be provided with long term confidential status. 3 Bill of Materials_x.docx The items in this document that are confidential are the parts list table and the PWA p/n listed in the description above the table. Any exhibit / information for which we have requested confidentiality, but which may not be accorded such treatment by the FCC, should be returned to us. The documents listed above contain trade secrets that are treated as confidential by us. Substantial competitive harm to us could result should they be made available to the public. Sincerely, Jeff Aymond Sr Electrical Engineer

Date: 2/20/23 Federal Communications Commission TO:

Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 Re: section 2.911(d)(7) filing To whom it may concern, This letter is to confirm that Jeff Aymond has accepted responsibility to act as the agent for service of process as acknowledged by the applicant, Jeff Aymond. U.S. Agent: Jeff Aymond Title: Principal Electrical Engineer Company Name: Entrust Corporation Address: 1187 Park Place Telephone No: 952-933-1223 Email: Jeff.Aymond@entrust.com FRN: 0007965262 The applicant accepts and acknowledges the obligation to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Signature of Applicant:

Signature of U.S. Agent (if different from applicant):

Name: Jeff Aymond Date: 2/20/23 Name:

Date: