SXP-2280 CDMA 1XRTT FIXED WIRELESS PHONE 800 MHz CDMA TECHNICAL MANUAL Copyright@2007 SungilTelecom Co.,Ltd Before installing your SXP-2280, carefully remove the contents from the shipping carton and check for evidence of shipping damage. If damage is found, contact your Authorized Sungil Distributor or shipping agent immediately. SAFE OPERATION INSTRUCTIONS IMPORTANT! Before installing or operating this product, read the SAFETY AND GENERAL INFORMATION section of this guide.
Install the unit indoors. Install the unit on a hard, flat surface for proper ventilation.
Do not expose the unit to rain or moisture
Do not place the unit on or close to sources of heat. IMPORTANT NOTICES TERMS AND CONDITIONS FOR USE OF SXP-2280 PRODUCTS ("Product") These Terms and Conditions are a legal contract between you and Sungil Corporation for the title to and use of the Product. BY RETAINING AND USING THE PRODUCT AFTER RECEIPT OF IT, YOU AGREE TO THE TERMS AND CONDITIONS INCLUDING WARRANTY DISCLAIMERS, LIMITATIONS OF LIABILITY AND INDEMNIFICATION PROVISIONS BELOW. IF YOU DO NOT AGREE TO THE TERMS AND CONDITIONS, DO NOT USE THE PRODUCT AND IMMEDIATELY RETURN THE UNUSED PRODUCT FOR A COMPLETE REFUND. You agree to accept sole responsibility for any misuse of the Product by you; and, in addition, any negligent or illegal act or omission of your or your agents, contractors, servants, employees, or other users of the Product so long as the Product was obtained from you, in the use and operation of the Product. Sungil Telecom Ltd. Corporate Headquarters 321 Gongdan-dong, Gumi City, Kyongbuk 730-030, Korea Sales and Technical Support Tel: +82-31-714-0038 Fax: +82-31-714-9174 E-mail: sales@sungiltel.com http://www.sungiltel.com 2006 Sungil Telecom Co. Ltd., All Rights Reserved 1.1 ICCB Construction 1.2 Button Layout ICCB has 15 keys which are numeric keys(0-9), *, # , Recall , Redial and ICC key. Each key is used to make call but under specific menu internally, *, #, Redial, Recall and ICC key could be used as function key. 0-9 : Number Button
*,#,Recall,Redial and ICC : Used at not only making call but also operation as follows,
*: The Cancel / Previous key to cancel what a user did or go previous menu.
#: The Store/Confirmation key to store/confirm what a user did like editing in editor. Recall: The up key for item selection on the menu. Redial: The down key for item selection on the menu. ICC: ICC stands for Indian Calling Card and this key has specific number for each region. This key is able to work only under Insert Coin status on LCD and dont work at other status. 1.3 Coin Selector The below picture is shown coin selector structure. The specification of it is as follows.
- Supports 1 Rs and 5 Rs.
- Maximum two coins for 1Rs and 5Rs. Under maximum insertion like two 1Rs and two 5Rs,
when a user inserts coin, it will be refunded. If a user inserts coins within 1 sec between coins, they will be just refund to avoid coins jam. 1.4 Coin Box A coin box installed at bottom of ICCB can store 500 coins for 5Rs. internally, whenever coins drop into coin box, Coin Counter increase by one and it let Box Full message come out when it would reach 500 coins and a user cannot make a call under this message. At this moment, a shop keeper (an operator ) can initial this coin counter with removing coins from coin box. To initialize coin counter, a operator should go Programming Mode menu and make counter zero. 2. Menu Construction 2.1 Menu Tree Root Menu Sub Menu Description To enter to the programming mode (ICCB Mode) 1) Open the ICCB. 2) To enter to this menu, Please follow below instructions. On-Hook handset -> Press Programming mode button on the main board -> Off-Hook handset. 3) First menu, 1.Cash Record will be displayed (ICCB Mode). Programming Mode
(ICCB Mode) 1:Cash Record 2:Local Prefix 3:MT code option 4:Tariff 5:ICC NUMBER 6:Display 7:Sound Show to Cumulative Coins Show to Current Coins Reset Cumulative Coins 1:Cumu. Coins 2:Current Coins 3:Cumu. Reset 4:Current Reset Reset Current Coins 5:Daily Coins Show to Daily Coins 6:Last Call List Show to list for last call 92 CODE ______ MT code YES MT code NO 1:Enter code 2:Tariff View 1:Show Option 2:Banner Selection to Banner or Date&Time Editing the Banner TATA Indicom a) AM/ PM Type b) 24 Hours Type c) Day of Week Type 3:Date&Time 1:Earpiece Vol 2:Ringer Vol 3:Speaker Vol 4:Key beep Vol 5:Ring Tone 6:Service Alert 8:S/W Version 9:Password Tariff Password To enter to the CDMA mode 1) Press the short keys follows 624709247*2690 2) The message on LCD will be displayed Enter Code ****. 3) Enter your password 0000 ( It can be changed ) 4) First menu, 1.Setting will be displayed. CDMA Mode Menu 1:Setting 2:Version 1:Voice Privacy 2:DTMF Tone 3:Password 4:AutoCall Time 1:S/W Version 2:H/W Version 3:PRL ID 1) To enter to Conversation Menu. 2) Press the Redial Button on Conversation 3) You can show the LCD message 1.Voice Privacy Conversation Menu 1.Voice Privacy 2.DTMF Tone To enter to NAM Mode Menu. 1) Press the short keys follows 47*869#*75259#
2) The message on LCD will be displayed PASSWORD ______. 3) Enter your password 000000 ( It can be changed ) 4) First menu, 1.GENERAL will be displayed. 01. ESN
(Electronic Serial Number) 02. CAI Ver
(Common Air Interface) 03.SO EVRC Read Only Read Only MSM6000 Chip just supported the 01. General
(Service Option)
(Enhanced Variable Rate Codec) EVRC. 04. SCM
(Station Control Mark) 05. LOCK CODE 06. SLOT MODE
. Read Only 07. SLOT CYCLE INDEX 08. RC (Radio Configuration) 09. SPC CHANG 10. SPC VALUE 01. Current NAM 02. Setup NAM 02. NAM 1 03. NAM 2 01. MCC 02. MNC 03.MIN 04.PHONE NO#
05. ACCOLC 06.PRIMARY CH. 07.SECOND CH. 01. Primary CH System A 02. Primary CH System B 01. Secondary CH System A 02. Secondary CH System B 01. NAM 1 or 02. NAM 2 08. ACQ SID 09. LOCK SID 10.H-S/NID Enable 11. HOME SID/NID CDMA HOME SID Enable Yes or No Home SID1~20 Home NID1~20 12.SID/NID LOCK LOCK Home SID1~20 LOCK Home NID1~20 13. CDMAPREF SYSTEM 14. PRL ENABLE 15. PRL ID 16. OTAPA ENABLE 17. MOB_TERM_HOME 18. MOB_TERM_FOR_SID 19. MOB_TERM_FOR_NID For CDG2 Testing You can selection the NAM1 or NAM2
(Mobile Country Code) * 3 digit
(Mobile Network Code) * 2 digit
*10 digit
(Directory Number) * 10 digit
(ACCess OverLoad Class) 0~ 15 2.2 Short Key List Key Items A-Key CDMA Mode Menu NAM Mode Menu Set ICCB Password to default value. Set CDMA Menu Password to default values. Master Clear Current Coin Count Action Keys
*75259#147*359#
624709247*2690 47*869#*75259#
Program mode push button + 5 times pressing emergency button +
'1036'
Program mode push button + 5 times pressing emergency button +
'4263'
##**90 or
##**47*869#90
*1*
Conversation Menu Conversation state
+ Redial button Emergency button Description To enter A-Key. To enter to CDMA Menu. To enter to NAM Mode Menu. Whenever Shop keeper would forget ICCB Password, he can use it to make a password as default 3842 Whenever Shop keeper would forget CDMA mode Password, he can use it to make a password as default 0000 In the factory, for products initialization for menus values. It will display how many coins are there in box currently. To see the conversation menu on conversation as follows 1) Voice Privacy 2) DTMF Tone To adjust earpiece volume level. Conversation Volume earpiece NAM Mode Menu for 47*869#*75259#
To enter NAM mode 1) General 2) Setup NAM A. Current NAM B. NAM1 => JUST USED C. NAM2 For examples, you can change to the PRL enabled/Disable, HOME SID/NID or MIN number. 2.3 ICCB User Mode Display 1 Handset On-Hook ICCB User Mode (Normal Call) TATA Indicom or MM/DD/YY hh:mm or According to Display Menu in CDMA Menu, you can change display type like the upper. Default is logo as TATA Indicom. 2 Handset Off-Hook INSERT COIN
- This screen request for insertion coin to make call. But registered free call numbers are available.
- During 45 secs, you didnt anything. Some alarm will be occurred on 3 After Insertion coin. 4 Dial numbers handset. PLEASE DIAL 114
- From Left, what you dialed will be displayed. Automatically it will make a call in 4 secs after dialing numbers. 5 Not match with Tariff 6 Making Call
(In case of Ordinary Call) Not Available Calling 7 Connected Call. 00Rs Time 00:60
(in case of Ordinary Call)
- On conversation, Value, time will be displayed( 00Rs Time 0:00 )
- Will display remained time and coin will be dropped in the inside box. At this time, whenever every 10 is remained, Alarm will be made one time and after then after 2 secs until call ends, Alarm will be made.
- During alarm sound, If you would insert coin, Alarm sound will disappeared no more.
- In case of local call, After current 60 secs would be used up, just inserted coin will be dropped to the box and new 60 secs will be displayed and you can keep talking without stoping..
- If you dont insert coin at this time, Call will end and screen will go to Insert Coin screen.
( INSERT COIN )
- Available talking time for each inserted coin will be displayed as much as value which was set on Call duration menu on ICCB mode.
% In case of international call, it is 10 secs. 8 Conversation Menu
(by Pressing Redial Button) Conv. Menu
- On the conversation, If you press Redial Button, Conversation Menu will come up as follows. 1.Voice Privacy 2.DTMF Tone 00:00 9 Ending call
- Totally elapsed time will be displayed during 15 sec. ( Need to be discussed with PTB team ) 10 Incoming 11 Recalll Incoming Call.
In case ICCB has remained time after call. Disaply text should be discussed with PTB team. 12 Redial
- in case of only IDLE state, Pressing Redial key can dialed last numbre which was made successfully.
- In case of no history, nothing is happened. 2.4 ICCB User Mode Display for Emergency Call and Toll Free ICCB User Mode (Emergency Call) 1 Emergency button
If you press Emergency button, Please Dial will be displayed in stead of Insert Coin message on LCD
- Be used at Virtual calling card number and real emergency number 2 Dial numbers like 100,101. 100
- Available emergency numbers are 100, 101, 102.
If dialed number is not emergency number, Not available.. message will be displayed. 3 Try to make call Emergency Call
- On Calling, "Emergecny Call" will be displayed
- In case of Toll free number, Toll Free Call will be displayed Toll Free Call
( It should be discussed with JP) Time 00:60
- Only Time will be displayed. ( Time 0:00 ) 4 During Conversation 2.5 ICCB Menu ( Programming Mode) To enter to the ICCB Programming Mode 1) Open the Coin Box 2) To enter to this menu, Please follow below instructions. On-Hook handset -> Press Programming mode button on the board -> Off-Hook handset. 3) The message on LCD will be displayed Enter Code ****. 4) Enter your password 3842 ( it can be changed ) 5) First menu, 1.Local Prefix will be displayed (ICCB Mode) Press '#': Saved and go back to the programming mode. Press *: Go back to the programming mode. Menu Display 1:Cash Record Sub Menu Display Description 1: Cumu. Coins Press #
Cumu.Tot 0000000 Press Redial Press * or #
Recall or 2: Current Coins Press #
Curr.Tot 00000 Press Redial Press * or #
Recall or Press 1, show to cumulative coins collected since installation. Press Recall, Menu Next Up as follows Press Redial. Menu Next Down as follows Cumu.Tot 0000000 Cumu.Use 0000000 Cumu.5Rs 0000000 Cumu.1Rs 0000000 Press *, Go back to the root menu. Press #,Saved and go back to the root menu Press 2, show to current coins collected in the cash box. Press Recall, Menu Next Up as follows Press Redial. Menu Next Down as follows Curr.Tot 00000 Curr.Use 00000 Curr.5Rs 00000 Curr.1Rs 00000 Press *, Go back to the root menu. Press #,Saved and go back to the root menu
% It counts the collected coins upto 700, After it shows BOXFULL. 3:Cumu. Reset Press #
4: Current Reset Press #
5: Daily Coins Press #
Day 0000Rs 000Cn Press * or #
5: Last Call List Press #
01: Phone number Press 1 or 2, #
2:Local Prefix 92 Code XXXXXXX 3:MT Code Option MT code Yes Press Recall, Redial Press * or #
4:Tariff Press #
1:Enter Code Press #
Press 3, You can erase cumulative coin counter Del Cumu.Coins?
Press *, Go back to the root menu. Press #,resetting the current coin counter. Press 4, You can erase current coin counter. Del Cur.Coins?
Press *, Go back to the root menu. Press #,resetting the current coin counter. Press 5, show to day total rupee with coin counts. Press *, Go back to the root menu. Press #,Saved and go back to the root menu Press 5, show to last calls information with number, time and rupee about up to 10 calls. Press 1, Move Next Up for last calls. Press 2, Move Next Down for last calls. 01: Phone number Press # => Show to the information as follows Rs 0000 Coin 000 Press *, Go back to the root menu. Press #,Saved and go back to the root menu Press Recall, Move up to the next mode. Press Redial, Move Down to the next mode. MT code Yes Press *, Go back to the root menu. Press #
Enter Code 56 Press 1~9,0, If you want to change the MT code, press the number. Press #, Updated the option MT code No Press *, Go back to the root menu. Press #, Updated the option You can make tariff Enter PWD XXXX 5:ICC Number 6:Display Input No XXXXXXX Press #
Input sec XXX Press * or #
2:View Tariff Press #
01:91 20s Press Recall, Redial Press * or #
1: Show Option Press #
Show Date&Time Press Recall, Redial Press * or #
2: Banner Press #
TATA Indicom Press * or #
3: Date&Time Press #
DTSet DayOfWeek Press Recall, Redial Press * or #
You can show Tariff press free call number Press 1. Entering the Show Option menu. Press Recall, Move up to the next mode. Press Redial, Move Down to the next mode. Show Blank Show Banner Show Date&Time Press *, Go back to the root menu. Press #, Updated the option Press 2, You can show to currently banner. Press #, Entering the editing mode Press Redial, insert space Press Emergency., Big or Small alpha mode Press *, Go back to the root menu. Press #, Updated the option Press 3, Entering the Date&Time menu Press Recall, Move up to the next mode. Press Redial, Move Down to the next mode. DTime DayOfWeek DTime 24Hours DTime AM/PM Press *, Go back to the root menu. Press #, Updated the option. 7:Sound 1: Earpiece Vol. Press #
EarVol. >>>>
Press Recall, Redial Press 1, Entering the volume of earpiece menu Press Recall, Volume Up Press Redial. Volume Down Press *, Go back to the root menu. Press * or #
2: Ringer Vol. Press #
RingerVol. >>>>
Press Recall, Redial Press * or #
3: Speaker Vol. Press #
SpeakerVol. >>>>
Press Recall, Redial Press * or #
4: Key Beep Vol. Press #
KeyBeepVol. >>>>
Press Recall, Redial Press * or #
5: Ring Tone. Press #
Press Recall, Redial Press * or #
6: Service Alert. Press #
SvcAlert On Press Recall, Redial Press * or #
New xxxx Press #
Re-Enter xxxx Press * or #
Press #, Updated the volume level. Press 2, Entering the volume of ringer menu Press Recall, Volume Up Press Redial. Volume Down Press *, Go back to the root menu. Press #, Updated the volume level. Press 3, Entering the volume of speaker menu Press Recall, Volume Up Press Redial. Volume Down Press *, Go back to the root menu. Press #, Updated the volume level. Press 4, Entering the volume of key beep menu Press Recall, Volume Up Press Redial. Volume Down Press *, Go back to the root menu. Press #, Updated the volume level. Press 5, Entering the ring tone selection menu Press Recall, Up Press Redial. Down Press *, Go back to the root menu. Press #, Updated the ring tone items. Press 6, Entering the Service Alert menu Press Recall, Service Alert is On Press Redial, Service Alert is Off Press *, Go back to the root menu. Press #, Updated the option You can show to the s/w version. You can show to the current password, default -> 3842 Press #, Entering the next mode for entering the new password Press 1~9,0, If you want to change the new password, press the number. We should be re-enter the new password. Press #, Updated the new password. 8:S/W Version 9:Password 2.5 CDMA Mode Menu To enter to the CDMA mode 1) Press the short keys as follows 624709247*2690 2) The message on LCD will be displayed Enter Code ****. 3) Enter your password 0000 ( It can be changed ) 4) First menu, 1.Setting will be displayed. Menu Display 1.Setting Press 1 2.Version Press 2 Description Press 1, Entering the Voice Privacy Menu. Press Recall, Changed the option to Standard as follows V.P. Standard Press Redial, Changed the option to Enhanced as follows V.P. Enhanced Press #, Go back to the root menu. Press 2, Entering the DTMF Tone Menu. Press Recall, Changed the option to Short as follows DTMF Tone Short Press Redial, Changed the option to Long as follows DTMF Tone Long Press #, Go back to the root menu. Press 3, Entering the next mode for entering the new password. Press 1~9,0, If you want to change the new password, press the number. We should be re-enter the new password. Press #, Updated the new password. Press 4, Entering the auto send time menu for orig. call Press Recall, Up for time count Press Redial. Down for time count Press *, Go back to the root menu. Press #, Updated the auto send time. Press 1, Entering the S/W Version menu. Press *, Go back to the root menu. Sub Menu Display 1: Voice Privacy Press #
V.P. Enhanced Press Recall, Redial Press * or #
2: DTMF Tone Press #
DTMF Tone Short Press Recall, Redial Press * or #
3: Password Press #
New xxxx Press #
Re-Enter xxxx Press * or #
4: Auto Call Time Press #
AutoCallTime XX Press Recall, Redial Press * or #
1: S/W Version Press #
S/W:XXXXXXXXXX Press *
2: H/W Version Press #
H/W:XXXXXXXXXX Press *
3: PRL ID Press #
PRL ID:XXXXXXXX Press *
1: Debug Screen Press #
Debug Screen Press #
Press 2, Entering the H/W Version menu. Press *, Go back to the root menu. Press 3, Entering the PRL ID menu. Press *, Go back to the root menu. Press 1, Entering the Debug Screen menu. You can enter the debug mode and you can show to the system information on CDMA network as follows. R 100 E 07 T 00 S 01243 N 00012 C 1011 PN 122 B 3.998V 2: Test Call Press #
TCall xxxxxxx Press Recall, Redial Press recall Press * or #
Press *, Go back to the root menu. Press 2, Entering the Test Call menu. Press Recall, Move up to the test call item. Press Redial, Move down to the test call item. Press recall, We can call on the selected option item. Press *, Go back to the root menu.
% Below show to the selected item, Markov~Loopback 3: Audible Tone Press #
A.Tone xxxxxxxx Press Recall, Redial Press * or #
Press 3, Entering the Audible Tone menu. Press Recall. Move up to a tone item. Press Redial, Move down to a tone item. Press #, Updated the tone item.
% Below show to the selected item. Korea, LatinAmerica, East Europe, China/Siri, Nicaragua, India 0.Hidden Press 0 4: Mirroring Press #
Do Mirroring Press Recall, Redial Press * or #
Press 4, Entering the mirroring menu. Press Recall, Do mirroring Press Redial, RestoreMirroring Press #, Updated the selected item. Battery Backup Failure If youre using the battery, the unit must be connected to AC power for at least 3 hours to fully charge the battery before it will provide back-up power to your SXP-2280. Verify that the battery has been charged for at least 3 hours and that the power source and its corresponding circuit breaker are functioning properly. Then, examine the battery for physical damage and corrosion. Replace the battery if necessary. Item Capacity Description 3.7V Li-ion(Nominal) / 1700mAh Talk Time Duration Over 3 Hours (Min) ( on SCI = 2) Standby Time Duration Over 140 Hours ( on SCI = 2) Charging Time Duration 3 Hours (Max) ( on SCI = 2) GENERAL INFORMATION AND SAFETY Your SXP-2280 Fixed Wireless Phone (FWP) functions as both a radio transmitter and receiver. When it is ON, the FWP receives and sends out radio frequency (RF) energy. The CDMA 800 unit operates in the frequency range between 824 and 894 MHz. When you use your SXP-2280, the cellular system handling your call controls the power level at which your unit transmits. Nominal power output is 230 mW. WARNING!
Only Authorized Service Personnel should remove the cover of your SXP-2280. For further assistance, contact your Authorized Sungil Representative. Please have your units model and serial number ready. The duration of your calls and operate your phone in the most power-efficient manner. Temperature Environment Operating Temperature: From -20C to +60C ; Up to 95% relative humidity (non-condensing). Storage Temperature: From -25C to +75C; Up to 95% relative humidity (non-condensing). Antenna Care and Replacement Do not use the SXP-2280 with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result. Have your antenna replaced by a qualified technician immediately. Use only a manufacturer-approved antenna. Unauthorized antennas, modifications, or attachments could damage the SXP-2280 . Driving Check the laws and regulations on the use of cellular products in the areas where you drive. Some jurisdictions prohibit your using a cellular device while driving a vehicle. Even if your jurisdiction does not have such a law, we strongly suggest that, for safety reasons, the driver use extreme caution when operating the cellular device while the vehicle is in motion. Always obey the law. Exposure to electronic Devices Most modern electronic equipment is shielded from RF energy. However, RF energy from cellular devices may affect inadequately shielded electronic equipment. RF energy may affect improperly installed or inadequately shielded electronic operating and entertainment systems in motor vehicles. Check with the manufacturer or its representative to determine if these systems are adequately shielded from external RF energy. You should also check with the manufacturer of any equipment that has been added to your vehicle. Consult the manufacturer of any personal medical devices (such as pacemakers, hearing aids, etc.) to determine if they are adequately shielded from external RF energy. Turn your SXP-2280 OFF in health care facilities when any regulations posted in the areas instruct you to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy. Aircraft Turn OFF your SXP-2280 before boarding any aircraft. Use it on the ground only with crew permission. Do not use it in the air. To prevent possible interference with aircraft systems, U.S. Federal Aviation Administration (FAA) regulations require you to have permission from a crew member to use your cellular phone (or any other cellular product) while the plane is on the ground. To prevent interference with aircraft systems, FCC regulations prohibit using your cellular device while the plane is in the air. Children Do not allow children to play with your SXP-2280 to prevent damage to the unit. Blasting Areas Construction crews often use remote control RF devices to activate off explosives. Therefore, to avoid interfering with blasting operations, turn your SXP-2280 OFF when in a "blasting area" or in areas posted:
"Turn off two-way radio."
FCC WARNING This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. RF Exposure Guidelines During transmitter operation, in order to meet RF Maximum Permissible Exposure Safety Guidelines, a minimum distance of 20cm shall be maintained between antenna and personnel.