FCC ID: R2NSDC-1000 HSDPA USB Modem

HSDPA USB Modem User Guide SDC-1000 Copyright Epivalley Co., Ltd has the copyright for this manual. This manual should not be reproduced or distributed with no prior written consent by Epivalley Co., Ltd. Registered Trademark The registered trademark stated in this manual is the registered trademark owned by the corresponding company. Condential & Proprietary This manual is the technical property of Epivalley Co., Ltd and it is prohibited to copy or utilize the manual with no prior consent by the technical data department. Table of Contents Connecting with PC 11 Checkig Connection 12 Epivalley HSDPA Dialer 12 Web 12 SMS 13 Address 16 Setting 17 Logs 18 Terminating Program 18 Trouble Shooting 19 Specication 20 Warranty 21 Cautions for Safety 4 Introduction 5 Specic Features 5 Conguration 6 Condition for Use 6 Name of Each Part 7 Installing Program 8 Deleting Program 9 Using USIM 10 PIN Code 10 PUK Code 10 Using SDC1000 11 Running Program 11 3 Cautions for Safety The cautions for safety are the contents to keep the safety of users and to prevent possible loss in property or convenience caused by ac-

cidents. The product should properly be used after sufcient understanding of the contents. Warning Do not discretionally disassemble, modify, or repair the product. Do not use the product if possible at the place where the use of handsets is prohibited. Use the product according to the rules and regulations of hospitals or medical institutions when using the product in such places. Do not use the product in the Airplane. Keep the product and accessories out of childrens reach. Do not touch or use with wet hands. Do not use the product outside in the thundering or lightning weather. Cautions Be careful not to give impact to the product and not to throw (or drop) the product because the product may be broken or deformed. When a trouble is occurred with the product, visit a designated service center to receive the service. Keep the USB port of the product clean always. The data to use the product is stored in USIM CARD; be careful to avoid possible damage to USIM CARD. Do not use or keep the product with magnetic storage media together. Do not use or keep the product at the very hot or very cold place or the place with large variation of temperature. If the model is disconnected from PC in switch-on status, the data may be damaged; disconnect the model from the PC after the pro-

grams are terminated and the power LED is turned off. When the product is used in connection with a notebook with use the battery only, the battery of the notebook may be somewhat rapidly discharged due to additional consumption of the power by the product. 4 Introduction Thanks you for purchasing SDC1000 of Epivalley Co., Ltd. SDC1000 is a USB Modem by HSDPA method to use wireless internet anytime and anywhere with no limit in time or place.

* HSDPA (High Speed Downlink Packet Access): This is the mobile communication method for sending/receiving data at the speed signicantly faster than that of W-CDMA or CDMA. Specic Features

* General Features

- USIM Support

- Internet, Intranet

- SMS

- Address

- Connection logs

* Mechnical Features

- Compatible microSD card

- Main Intenna

- UMTS Diversity Intenna (2100MHz)

- 7 Colors LED

- Dimension: 38mm(W) 16mm(H) 78mm(D)

* Data Rate

- Download: Up to 7.2 Mbps

- Upload: Up to 384 Kbps

* Frequency Band

- GSM: 850 / 900 / 1800 / 1900 MHz

- UMTS: 850 / 1900 / 2100 MHz 5 Conguration The conguration of SDC1000 product is as shown below:

Main Body Manual USB Extension Cable

* Note: The conguration of the product may be somewhat changed wit no prior notice to improve the functions of the product. Condition for Use The minimum specication of the PC to use SDC1000 is as described below:

Operating System: Windows 2000, XP or Vista(32bit, 64bit), Mac OS X CPU: Pentium 4, 1 GHz or above Memory: 128 MB RAM or above Hard disk space: 100 MB or above Connection port: USB slot A-Type 6 Name of Each Part Front Part Lateral Part Lower Part Slide knob USB Port USIM Slot LED Display Micro SD Slot USB Port 7 Installing Program S/W is included in USB Modem. 3. To install the program, les are copied from Modem to PC. 5. Designate the destination folder to install the program and click [Next] button. 1. When SDC1000 is inserted into the USB port of the PC to use SDC1000, the installation program is automatically run.

* Note: If SDC1000 Dialer program is already installed, the program is not auto-

matically run. If you want to reinstall the program, manu-

ally start the installation program with use of explorer. 2. When the installation is automatically started, below-shown screen is displayed. Choose the setup language and click

[OK] button.

* Note: If the installation is not automatically run, doubleclick setup32.exe le in CD.

(In case of Vista 64, setup64.exe) 4. When Welcome to the Installshield Wizard message is displayed, click

[Next] button. Destination folder of the program 6.Click [Install] button to install the program. 8 Deleting Program 7. Files are copied from Modem to PC. The method to delete Epivalley HSDPA Dialer installed in PC is as described below. 1. On the task bar, click [Start] - [Program]

- [Epivalley] - [SDC1000_Dialer] - [Unin-

stall] in order. 8. Program is completely installed. Click

[Finish] button to nish the program installation. 2. When a popup screen is displayed and it is asked whether to delete the program, click [Yes] button. 9 Using USIM USIM (universal subscriber identity module) consists of SIM (subscriber identity module) containing subscribers information and UICC (universal IC card) and various func-

tions including user authentication, global roaming, and e-commerce are performed with a card. For proper use of SDC1000, USIM Card should be inserted. Carefully input the password and click [OK]

button; if valid password is inputted, Epival-

ley HSDPA Dialer program is properly run and, if invalid PIN Code is inputted, an error message is displayed as shown below.

* Note: If invalid PIN Code is inputted three or more times, USIM Card is blocked and cannot be used. PIN Code PIN Code is the password to be inputted for conrmation when running the program to use SDC1000.

(If PIN Lock Option is in [ON] status, you should input the password when starting Epivalley HSDPA Dialer program.) Blocked USIM Card may be released with input of PUK Code. PUK Code PUK Code is a pre-dened code to release blocked USIM Card. Input PUK Code and new PIN Code and click [OK] button to release blocked USIM Card.

* Note: PUK Code may be identied in USIM Pack when purchasing USIM and consists of 8digit numbers. If invalid PUK Code is inputted, an error message is displayed. In this case, click

[OK] button and input valid PUK Code and new PIN Code to release blocking.

* Note: Be careful because, if you fail in inputting valid PUK Code 10 or more times, USIM Card is blocked and cannot be used. (You have to purchase USIM Card again.) 10 Running Program Run Epivalley HSDPA Dialer program be below-described method. 1. 1. Doubleclick the shortcut icon (Epivalley HSDPA Dialer) on the window. Or on the task bar, click [Start] - [Program]

- [Epivalley] - [SDC1000_Dialer] - [Epivalley HSDPA Dialer] in order. Using SDC1000 Connecting with PC The USB Port of SDC1000 is built in the main body. Pull out the USB Port and con-

nect it with PC. 1 2 3 4 2. Epivalley HSDPA Dialer program is run. Check whether LED part is lighted on. 11

* Note: When SDC1000 is not used, re-

move it from PC and push USB Port inside to be stored.

* Note: When SDC1000 is used connecting with a notebook, the receive sensitivity may be reduced due to the electronic wave generated by LCD monitor. In this case, use it using the USB extensible cable supplied when purchasing the product. Checkig Connection When SDC1000 is connected with PC, the connection status may be conrmed on the status display bar at the lowest part of the program. Using SDC1000 Ths status of product may also be checked on the LED at the side of SDC1000. RED Yellow GREEN Orange Power On Blink: No service In service Blink: Receiving SMS No SIM When SDC1000 is properly connected When SDC1000 is not connected When SDC1000 is connected but USIM Card is not inserted or is improperly insertted 12 Epivalley HSDPA Dialer Connection with intenet or sending/receiv-

ing SMS is possible with use of Epivalley HSDPA Dialer program and the telephone numbers and addresses may conveniently be managed in the address list. Web

[Web] is the menu used in connecting with internet. When using [Web] for the rst time, the prole needed to connect with internet should be created and, from the next use, internet connection is possible with use of the stored prole. 1. Click [Web]. 2. Create the prole needed to connect with internet. Click [Add] or click the right button of mouse and select [Add]

button. Using SDC1000 4. Select the prole created for internet connection and click [Connect] button. 3. Input Prole Name to create the prole for internet connection and input the information needed to connect with prole. Click [OK] button to create a prole. 5. Internet is connected and the time of internet use and packets may be checked. SMS

[SMS] is the menu that is used in sending short messages or consrming received short messages. Short messages may be sent with setting the sending time and the short messages received from numbers for rejection are automatically classied into spam mes-

sages. Send 1. Click [SMS] button. 13 Using SDC1000 2. Write the message on Editor screen. 4. Click [Send] button the send the message. Clear: erase the message written on Editor screen. Templates: designates the templates of message Emoticon: inputs emoticon. Special: inputs special characters. 3. Input the telephone number to receive the message and click [Add] button to designate the number as the receivers number. The telephone number may be added by selecting a number in the numbers registered in the address or may be designated by selecting a number in the message sending his-

tory after clicking [Log] button. Wrong designated receivers number may be deleted by selecting the receiving number in the telephone number list and by clicking

[Del] button. To send a messages with reservation, click [Reserved]

button designate the time and date to send the messages. Inbox In [Inbox] tab, you can see the received messages. Received messages are automatically stored in Inbox. 14 When a message is received, the receipt is noticed on the Windows popup screen and, if the program is minized, the tray icon ashes. The messages may be arranged by Date, Number, Content, Destination, and Message Status; the message may be relayed with clicking [Forward] button and a reply message may be sent with clicking [Reply] button.

* Note: The method to notice the receipt of a message may be set in [Incoming SMS Alert] in [Setting] menu. Using SDC1000 Sent In [Sent] tab, you can check the mes-

sages sent. The messages may be arranged by Date, Number, Content, Destination, and Message Status and the message may be relayed with clicking [Forward] button. Also, the destination (PC or USIM) where the messages are stored may be conrmed with the icon. Draft In [Draft] tab, you can check the reserved messages, the messages not sent, and the messages failed in sending. The messages may be arranged by Date, Number, Content, Destination, and Message Status and the message may be relayed with clicking [Forward] button. Spam In [Spam] tab, you can check the mes-

sages received from the telephone numbers designated as Spam and the messages containing the words desig-

nated as Spam. The messages may be arranged by Date, Number, Content, Destination, and Message Status and the message may be stored with clicking [Save] button.

* Note: Click [Save] button to store the tele-

phone number to which the message was sent or change the destination to store the message.

* Note: Click [Resend] button to send the selected message again.

* Note Click [Inbox] button to move or resend the selected message. You can dene the Spam messages in

[Spam message Settings] in [Setting]

menu. 15 Address

[Address] menu is used to register, edit, and delete telephone numbers. Viewing Registered Telephone Numbers You can check the stored telephone numbers with selecting All, PC, or SIM tab and you can view the registered tele-

phone numbers in the arrangement by Name, Mobile, Address, Ofce, Home, Fax, E-mail, and Comments. Using SDC1000 putting the search condition, and clicking

[Search] button. Registration, Correction, and Deletion of Telephone Numbers You can register a new telephone num-

ber or correct or delete registered tele-

phone numbers with use of the button at the lowest part of Address Menu. Searching Telephone Numbers You can search the registered telephone numbers with selecting the search type

(Name, Mobile, Group, Address, Ofce, Home, Fax, E-mail, and Comments), in-

16 Add: registers a new telephone number in the telephone book. Edit: may correct the information on the registered telephone number. Delete: deletes the registered telephones from the telephone book. Sending Short Messages You can send a message to the registered telephone numbers with clicking [SMS] button at the lowest part of Address Menu. Check the telephone numbers to send the message and click

[SMS] button. Managing Telephone Number Groups Telephone numbers may conveniently be managed with classication into groups. A group may be created with clicking the right button of mouse and clicking [Add]

button. You can move the registered telephone numbers to another group with Drag &

Using SDC1000 Drop and send a message to a group or groups at a time. Setting In [Setting] menu, you can set the envi-

ronment related with the use of Epivalley HSDPA Dialer program. SMS In [SMS] tab, you can set the information on notice of message receipt and Spam message management. Also, you can move or copy the regis-

tered telephone number by selecting the number and clicking the right button of mouse. General In [General] tab, you can set the informa-

tion on the language and color theme related with Windows. USIM In [USIM] tab, you can set the informa-

tion related with PIN Code. 17 Using SDC1000 Lock In [Lock] tab, you can set the information related with lock function. Logs In [Logs], you can check the information on the date and time of internet connec-

tion and the quantities of sent/received data in relation to use of internet. Terminating Program To terminate Epivalley HSDPA Dialer program, click at the right top of the program. Information In [Information] tab, you can check the information related with S/W Version, Modem, and Memory. Prev: conrms the internet logs of previous month. Next: conrms the internet logs of next month. Export: The internet logs of current month are downloaded in csv le type. Or click the right button of mouse on the tray icon and click [Exit] button. 18 Trouble Shooting If you informs the expected problems and solutions in relation to the use of SDC 1000, the troubleshooting will be prepared with referring to the related contents of other models. 19 Specication Specication will be prepared after conrm-

ing the nal specication. 20 Warranty Let use be informed of the warranty policy of Epivalley. 21 CE User Information Hereby, Epivalley co., LTD. declares that this SDC-1000 is in compliance with the essential requirements and other relevant provisions of Directive1999/5/EC. FCC RF EXPOSURE INFORMATION This USB modem is approved for use in normal size laptop computers only (typically with 12 or larger display screens). To comply with FCC RF exposure requirements, this modem should not be used in configurations that cannot maintain at least 12 mm from users and bystanders; for example, in certain laptop and tablet computers and configurations where the USB connectors are unable to provide or ensure the necessary separation is available between the modem and its users to satisfy compliance. The FCC has granted an Equipment Authorization for this HSDPA USB MODEM with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this USB modem is on file with the FCC and can be found under the Display Grant section of http://www.fcc.gov /oet / fcc id after searching on FCC ID: R2NSDC-1000 For more information about RF exposure, please visit the FCC website at www.fcc.gov WARNING! Read this information before use Caution Modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC Compliance Information This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received. Including interference that may cause undesired operation. Information to User This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/ tv technician for help.