FCC ID: PJWMBRW35 Mobile Broadband Router

Ericsson W3x Series Mobile Broadband Router for WCDMA/HSPA Mobile Networks Safety and Regulatory Information Ericsson W3x Series Mobile Broadband Router for WCDMA/HSPA Mobile Networks Safety and Regulatory Information Copyright Ericsson AB 2008 - All Rights Reserved Disclaimer No part of this document may be reproduced in any form without the written permission of the copyright owner. The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. Ericsson shall have no liability for any error or damage of any kind resulting from the use of this document. 3/1551-CRH 102 168 Uen Rev PA2 2008-11-04

. ii

. Contents 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.10 1.11 1.12 2 2.1 2.2 2.2.1 2.2.2 2.3 2.3.1 2.4 2.5 2.6 2.7 2.8 2.9 2.10 Safety Information Product Care and Safety Antenna Care Radio Wave Exposure Information Personal Medical Devices Potentially Explosive Atmospheres Intended Use Power Supply Installation Practices Battery (W35 only) Mains Power Fails Children Moving or Storing Regulatory Information Declaration of Conformity FCC Statement FCC Part 15 Statement Note Caution Canada Statement Canadian ICES-003 Statement Wireless Guidance Power Supply Environmental Conditions WiFi Compliance RoHS Compliance USB Compliance WEEE Directive 3/1551-CRH 102 168 Uen Rev PA2 2008-11-04 1 1 2 2 3 3 3 4 4 4 4 4 5 6 6 7 7 7 8 8 8 9 10 10 10 10 10 iii Safety Information 1 Safety Information 1.1 Note: Read this information before using your Ericsson Mobile Broadband Router (MBR) W30/W35 for safe and efficient use. Product Care and Safety Your Ericsson W30/W35 is a highly sophisticated electronic device. To get the most out of it, be sure to read the following text about product care, safety and efficient use. Treat your product with care, keep it in a clean and dust free place. Do not expose your Ericsson W30/W35 to liquid, moisture or humidity. Do not expose your Ericsson W30/W35 to extreme high or low temperatures; refer to the topic Environmental Conditions documented on page 7 for more detailed information. Do not expose your Ericsson W30/W35 to open flames or lit tobacco products. Do not drop, throw or try to bend the product since rough treatment could damage it. Do not use this product near water, for example, near a bathtub, washbowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using a telephone (other than cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Do not use this product near medical equipment. Do not use this product in an aircraft because this product can transmit signals that could interfere with various onboard systems and may be dangerous to the operation of the aircraft or disrupt the cellular network. The optional battery within the W35 should be removed. Do not use this product near life support equipment, or any equipment which may be susceptible to any form of radio interference. In such areas this product must be powered off. This product can transmit signal that could interfere with such equipment. 3/1551-CRH 102 168 Uen Rev PA2 2008-11-04 1 Safety Information Do not attempt to disassemble you Ericsson W30/W35. A broken warranty seal will void the warranty. The product does not contain consumer serviceable components. Only Certified Service Centers should perform service. Do not use any accessories other than those approved by Ericsson or approved for use by your service provider. Use of non-original, or non-

approved accessories, may result in loss of performance, damage to the product, fire, electric shock or injury and may violate regulations. The warranty does not cover product failures that have been caused by use of non-original or non-approved accessories. Only Telephone equipment approved in the country where the W35 is used is to be connected. Antenna Care Use only an antenna that has been specially designed and approved for your Ericsson W30/W35. Use of unauthorized antennas, modifications, or attachments could damage the router and may violate the appropriate regulations, causing loss of performance and radio frequency (RF) energy above the recommended limits. Do not hold or touch the antenna when the Ericsson W30/W35 is in use. Holding or touching the antenna affects call quality. Do not use the Ericsson W30/W35 if the antenna or antenna cable is damaged or missing. Do not place the telephone cord or the power supply cord on, or near, the Ericsson W30/W35 antenna or antenna cable. Do not cover or place an obstruction on, or around, the antenna. Radio Wave Exposure Information The Ericsson W30/W35 is a low-power radio transmitter and receiver. During use, it emits low levels of radio frequency energy (also known as radio waves or radio frequency fields). Governments around the world have adopted comprehensive international safety guidelines, developed by scientific organizations, e.g. ICNIRP

(International Commission on Non-lonizing Radiation Protection) and IEEE

(The Institute of Electrical and Electronics Engineers Inc.) through periodic and thorough evaluation of scientific studies. 1.2 1.3 2 3/1551-CRH 102 168 Uen Rev PA2 2008-11-04 Safety Information 1.4 1.5 1.6 These guidelines establish permitted levels of radio wave exposure for the general population. The levels include a safety margin designed to assure the safety of all persons, regardless of age and health, and to account for any variations in measurements. Specific Absorption Rate (SAR) is the unit of measurement for the amount of radio frequency energy absorbed by the body. The SAR level for this product was determined at the highest certified level in laboratory conditions using a measurement standard published by the European Committee for Electrotechnical Standardization (CENELEC). With the antenna solutions recommended by Ericsson, the maximum radio wave exposure is below the limit in the international safety guidelines within a few centimeters from the antenna. Consequently, for recommended placement of the terminal and antenna, the radio wave exposure levels are below the limits. More information on radio frequency exposure can be found on:

http://www.ericsson.com/health Personal Medical Devices Radio waves may affect the operation of cardiac pacemakers and other implanted equipment. If a minimum distance of 15 cm is kept between the antenna and the pacemaker, the risk of interference is limited. If you have any reason to suspect that interference is taking place, immediately move away from the antenna. Contact your cardiologist for more information. For other medical devices, please consult the manufacturer of the device. Potentially Explosive Atmospheres Do not use your Ericsson W30/W35 in an area where a potentially explosive atmosphere exists. Intended Use This product is designed and approved for private and public use in an indoor location. The Ericsson W30/W35 is designed for use within the home or office. Any attached cabling must remain internal to the building. 3/1551-CRH 102 168 Uen Rev PA2 2008-11-04 3 Safety Information 1.7 1.8 1.9 1.10 1.11 Power Supply Ensure that your AC power outlet is adequately grounded, is situated near the Ericsson W30/W35 and easily accessible. Connect the power supply cord only to the AC power outlet that meets the specifications marked on the Ericsson W30/W35 supply. Never alter the AC power cord or plug. If necessary have the correct outlet installed by a qualified electrician or call your service provider for assistance. To reduce risk of damage to the electric cord, remove it from the outlet by holding onto the AC adapter rather than the cord. Make sure the cord is positioned so that it will not be stepped on, tripped over or otherwise subjected to damage or stress. Installation Practices In locations prone to lightning, installation practices providing protection should be followed. Battery (W35 only) Caution Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Mains Power Fails This equipment will remain inoperable when mains power fails unless the optional battery (W35 only) has been installed and is charged. Children Do not allow children to play with your Ericsson W30/W35 since it contains small parts that could become detached and create a choking hazard. 4 3/1551-CRH 102 168 Uen Rev PA2 2008-11-04 Safety Information 1.12 Moving or Storing Turn off the Ericsson W30/W35 by disconnecting the power supply as well as the battery (if one is installed). If you are transporting the Ericsson W30/W35 on an aircraft, you will be asked to remove the battery from the unit. For updated information about the transportation and use of wireless communication equipment, contact the appropriate local and national regulatory agency or your service provider. 3/1551-CRH 102 168 Uen Rev PA2 2008-11-04 5 Regulatory Information 2 Regulatory Information This device (Ericsson W30/W35) must be installed and used in strict accordance with the manufacturers instructions that comes with the product. In some situations or environments, the use of wireless devices may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include:

Using the Wireless equipment in an environment where the risk of interference to other devices or services is perceived or identified as harmful. If you are uncertain of the policy that applies on the use of wireless equipment in a specific organization or environment you are encouraged to ask for authorization to use this device prior to turning on the equipment. The manufacturer is not responsible for any interference caused by unauthorized modification of the devices included with this kit, or the substitution or attachment of connecting cables, antennas and equipment other than specified by the manufacturer. The correction of interference caused by such unauthorized modification, substitution or attachment will be the responsibility of the user. The manufacturer and its authorized resellers or distributors are not liable for any damage or violation of government regulations, regulatory approvals and misuse of any kind failing to comply with these guidelines. The Ericsson W30/W35 has regulatory approvals in the following markets/countries:

EU, US, Canada, Australia, New Zealand, Singapore, South Africa and Malaysia. 2.1 Declaration of Conformity Hereby, Ericsson AB declares that this product is in conformity with the requirements and other relevant provisions of the following European directives for the CE mark:

2006/95/EC: Low Voltage Directive (LVD) 1999/5/EC, Radio Equipment and Telecommunications Terminal Directive (R&TTE). 6 3/1551-CRH 102 168 Uen Rev PA2 2008-11-04 Regulatory Information 2.2 Note: Shielded Ethernet cables must be used in order to comply with the emission standards. FCC Statement This device (Ericsson W30/W35) complies with CFR47 Part 15, Part 22 and Part 24 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Responsible party in US is:

Ericsson Inc. with address: 6300 Legacy Drive, Plano, TX 75024, U.S.A. and phone no. 972-583-2000. 2.2.1 FCC Part 15 Statement Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. consult the dealer or an experienced radio/TV technician for help. Note: Shielded Ethernet cables must be used in order to comply with the emission standards. 2.2.2 Caution To comply with FCC RF exposure compliance requirements when using the roof antenna, a separation distance of at least 20 cm (8 inches) between the equipment and the body must be maintained. 3/1551-CRH 102 168 Uen Rev PA2 2008-11-04 7 Regulatory Information 2.3 2.3.1 2.4 Changes or modification to this product not authorized by the manufacturer could void your authority to operate the equipment and invalidate approvals. Canada Statement This product meets the applicable Industry Canada technical specification. Canadian ICES-003 Statement This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB003 du Canada. Note: Shielded Ethernet cables must be used in order to comply with the emission standards. Wireless Guidance Wireless devices are closely regulated and some countries have different restrictions. If you are uncertain contact the local Radio approval authorities to check if there are any restrictions of use before you use the equipment. The wireless device are only qualified for use in the countries identified by the approval marks but notice that you also must follow additional limitations, cautions, concerns if any. Care should be taken to minimize human contact during normal operation. Some circumstances and environment require restrictions on wireless devices. The table on the next page delineates the IEEE 802.11 channels and their corresponding center frequencies. The information is deemed to be accurate; however local regulatory authorities should be consulted before using such equipment. 8 3/1551-CRH 102 168 Uen Rev PA2 2008-11-04 Regulatory Information Table 1 Channel Number 1 2 3 4 5 6 7 8 9 10 11 12 13 Geographic Indoor Usage IEEE 802.11g Channels Channel Frequency 2412 MHz 2417 MHz 2422 MHz 2427 MHz 2432 MHz 2437 MHz 2442 MHz 2447 MHz 2452 MHz 2457 MHz 2462 MHz 2467 MHz 2472 MHz US, CA, ETSI, SI, AU, NZ, SA, MA US, CA, ETSI, SI, AU, NZ, SA, MA US, CA, ETSI, SI, AU, NZ, SA, MA US, CA, ETSI, SI, AU, NZ, SA, MA US, CA, ETSI, SI, AU, NZ, SA, MA US, CA, ETSI, SI, AU, NZ, SA, MA US, CA, ETSI, SI, AU, NZ, SA, MA US, CA, ETSI, SI, AU, NZ, SA, MA US, CA, ETSI, SI, AU, NZ, SA, MA US, CA, ETSI, SI, AU, NZ, SA, MA US, CA, ETSI, SI, AU, NZ, SA, MA ETSI, SI, AU, NZ, SA, MA ETSI, SI, AU, NZ, SA, MA US = United States CA = Canada ETSI = ETSI countries SI = Singapore AU = Australia NZ = New Zealand SA = South Africa MA = Malaysia Only use the provided approved antennas and correct settings (channels, output power etc.). The transmitter shall not be co-located with other transmitters or antennas. 2.5 Power Supply AC Input: 100 - 240 VAC; 50-60 Hz 3 pole AC inlet connector (IEC 320 power inlet). Available plugs: EU, UK, USA and AU. 3/1551-CRH 102 168 Uen Rev PA2 2008-11-04 9 Regulatory Information 2.6 2.7 2.8 2.9 Note: For use only with approved supplied power adapter. In the event of equipment malfunction, replace only with an AC/DC Adapter specified by Ericsson. Environmental Conditions Maximum environmental values during use:

Temperature: 0o C to +45 C o Humidity: 5% to 95% RH, non-condensing. WiFi Compliance The Ericsson W30/W35 has been tested for interoperatibility with the WiFi standard (the global industry-standard for local wireless networking) and supports all Wi-Fi certified client devices. RoHS Compliance The Ericsson W30/W35 meets the requirements in the European RoHS directive (2002/95EC). USB Compliance The Ericsson W30/W35 meets the requirements in the USB-IF Compliance Program for systems. 2.10 WEEE Directive Requirements according to WEEE-directive (2002/96/EC) Disposal of Old Electrical and Electronic Equipment

(Applicable in the European countries with separate collection systems). This symbol on the product indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will prevent potential negative consequences for the environment and human health, which could 10 3/1551-CRH 102 168 Uen Rev PA2 2008-11-04 Regulatory Information otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. Ericsson offers take-back and recycling services for products in many locations around the world. The customers are advised to contact the local Ericsson representative for further information. 3/1551-CRH 102 168 Uen Rev PA2 2008-11-04 11 Ericsson AB www.ericsson.com Ericsson AB 2008 - All Rights Reserved 3/1551-CRH 102 168 Uen Rev PA2 2008-11-04

Ericsson W3x Series Mobile Broadband Router for WCDMA/HSPA Mobile Networks User's Guide Ericsson W3x Series Mobile Broadband Router for WCDMA/HSPA Mobile Networks User's Guide Copyright Ericsson AB 2008 - All Rights Reserved Disclaimer No part of this document may be reproduced in any form without the written permission of the copyright owner. The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. Ericsson shall have no liability for any error or damage of any kind resulting from the use of this document. Trademark List Firefox Internet Explorer MSN Messenger Opera Safari Windows Firefox is a registered trademark of Mozilla Foundation. Internet Explorer is a registered trademark of Microsoft Corporation. MSN Messenger is a registered trademark of Microsoft Corporation. Opera is a registered trademark of Opera Software ASA. Safari is a registered trademark of Apple Computer, Inc. Windows is a registered trademark of Microsoft Corporation. All other brand and product names are trademarks or registered trademarks of their respective holders. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12

. ii

. Contents 1 1.1 1.2 2 2.1 2.2 2.3 2.4 2.5 2.5.1 2.5.2 2.5.3 2.5.4 3 3.1 3.1.1 3.1.2 3.1.3 3.2 3.2.1 3.2.2 3.3 3.3.1 3.3.2 3.3.3 3.3.4 3.4 3.4.1 Introduction Structure of this Guide Related Documents W3x Series Overview Product Variants W30 Data Router W35 Data and Voice Router Feature Summary Housing Back Side Interfaces Left Side Interfaces Right Side Interface Front Panel Configuration and Management Access and Login to the Web User Interface Enter PIN code Enter Password Inactivity Timeout Overview Alarms Network Information Wireless LAN Configuration Wizard Enable the Wireless LAN Network Name Wireless LAN Authentication Wireless LAN Configuration Wizard Confirmation Internet Mobile Network Connection Details 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 1 1 2 3 3 4 5 5 7 7 9 10 10 14 14 15 15 16 18 19 20 21 21 22 22 28 29 30 iii Contents 3.4.2 3.4.3 3.4.4 3.5 3.5.1 3.5.2 3.5.3 3.6 3.6.1 3.6.2 3.6.3 3.6.4 3.6.5 3.6.6 3.6.7 3.6.8 3.6.9 3.6.10 3.7 3.7.1 3.7.2 3.7.3 3.8 3.8.1 3.8.2 3.8.3 3.8.4 3.9 3.9.1 3.9.2 3.9.3 3.9.4 3.9.5 Traffic Statistics Authentication Cellular Band Selection LAN LAN IP Address DHCP Server LAN Port Status Wireless LAN Enable WLAN Region Radio Channel Transmit Power [dBm]

Data Rate Scan for Wireless Networks Network Name (SSID) WLAN Security Connected Devices Whitelist NAT UPnP IGD Application Level Gateways Port Forwarding File and Printer Sharing How it Works Host Name and Workgroup File Sharing Printer Sharing System Basic System Information Configuration Backup and Restore System Restart Software Update Factory Reset 31 31 34 36 36 37 39 40 40 41 41 41 41 42 43 43 45 45 47 48 48 49 52 52 53 53 54 56 57 57 58 59 60 iv 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Contents 3.10 3.10.1 3.11 3.12 Event Log Persistent Logging Change Password Logout 4 4.1 4.2 5 5.1 5.2 6 6.1 6.1.1 6.1.2 6.2 6.2.1 6.2.2 6.2.3 6.3 6.3.1 6.3.2 6.3.3 6.3.4 7 7.1 7.2 7.3 7.4 7.4.1 Telephony and Fax (W35 only) SIM Authentication Information Tones Battery (W35 only) Installation of the Battery Battery Function PC Configuration IP Settings Obtain IP Settings Automatically Configure Static IP Address Wireless LAN Settings Prepare the Wireless Client(s) Install the Wireless LAN Interface Configure Access to the W3x WLAN USB Sharing Settings Check Workgroup Settings Access a Shared Storage Device Set Up a Connection to a Shared Storage Device Access a Shared Printer Troubleshooting Restart Reset to Factory Default Settings LAN Connections Internet Access Change TCP Settings 1/1551-CRH 102 168 Uen Rev F 2008-11-12 62 63 63 64 65 65 66 67 67 67 68 68 68 70 70 70 70 71 71 72 73 73 74 77 77 77 78 79 80 v Contents 7.5 7.6 7.7 Wireless LAN Connection Access to Shared Files or Printer Telephony and Fax Service (W35 only) 80 82 83 Glossary 85 vi 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Introduction 1 Introduction 1.1 This chapter describes the structure of this guide and provides a list of reference documents. Structure of this Guide This Users Guide contains information that is needed for an end-user to configure and manage the Ericsson Mobile Broadband Router (MBR) W3x product series. This guide describes both the Ericsson W30 and W35 and when design, functionality and commands are in common, the term Ericsson W3x is used. Any information that is unique to a specific model is described with the appropriate product name; Ericsson W30 or Ericsson W35. The following chapters are included:

Chapter 1 Introduction provides information about this guide and provides a list of reference documents. Chapter 2 W3x Series Overview gives an overview of the Ericsson W3x product series Chapter 3 Configuration and Management provides detailed information about how to perform configuration and management of the Ericsson W3x. Chapter 4 Telephony and Fax (W35 only) includes information about the telephony and fax function in the Ericsson W35. It also includes instructions on how to enter the SIM authentication codes via a telephone handset. Chapter 5 Battery (W35 only) includes information about how to handle battery installation and charging for the Ericsson W35. Chapter 6 PC Configuration gives instructions for configuring computers to work with the Ericsson W3x. Chapter 7 Troubleshooting describes how to solve a number of issues that could occur during installation, configuration, and use of the Ericsson W3x. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 1 Introduction 1.2 The Glossary includes abbreviations and explanations to technical terms used in this guide. Related Documents In the following documents, more information about the Ericsson W3x can be found:

Ericsson W3x Series, Quick Installation Guide, XX/LZT 108 9869, Ericsson AB 2008. Ericsson W3x Series, Safety and Regulatory Information, 3/1551-CRH 102 168, Ericsson AB 2008. Ericsson W3x Series, License Information, 4/1551-CRH 102 168, Ericsson AB 2008. 2 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 W3x Series Overview 2 W3x Series Overview This chapter gives an overview of the Ericsson Mobile Broadband Router

(MBR) W3x product series. 2.1 Product Variants The Ericsson W3x product series consist of two models:

Ericsson W30 Data Router Ericsson W35 Data and Voice Router The W3x product series facilitates protected, high-speed Internet access for multiple users in home and small or branch office environments. It includes advanced data capabilities such as router and switch functionality, and provides the users with multiple possibilities for local area connectivity

(Ethernet and WLAN). With WCDMA/HSPA radio access capability the Ericsson W3x is well suited to provide broadband data access with data speeds similar to fixed line DSL services. The data rate is up to 7.2 Mbps and the up-link speed is up to 2 Mbps. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 3 W3x Series Overview 2.2 W30 Data Router The Ericsson W30 data router provides data capabilities such as data access (e.g. Internet) in the respect that it allows multiple computers to be connected to the router using Ethernet or wireless LAN (WLAN). It also supports file and printer sharing via the USB port. Figure 1 - Overview of Interfaces on the Ericsson W30 4 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 W3x Series Overview 2.3 W35 Data and Voice Router The Ericsson W35 data and voice router incorporates the same set of functions and data features as the Ericsson W30. Additionally, this model also includes high quality voice and fax services via the telephony interfaces. A broad range of network related services such as Prepaid Subscription, CLI (Calling Line Identification), Call Waiting, Call Barring, Call Forwarding, and Multiparty Conference Calls are available. WCDMA/HSPA radio access is well suited for combined and efficient data and voice transmission over the mobile network. Figure 2 - Overview of Interfaces on the Ericsson W35 2.4 Feature Summary The Ericsson W3x features the latest technology, which makes it highly suitable for everyday broadband services:

Wireless Broadband Services at Reliable High Speed The Ericsson W3x uses WCDMA/HSPA as primary radio access and GSM/GPRS/EDGE as fall-back. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 5 W3x Series Overview Web-based user interface for configuration of the device with wizard support. Advanced Networking Support an advanced local network setup providing IP routing, Ethernet switching, DHCP service, and NAT. File and Printer Sharing Network file and printer sharing is supported through a USB connection. Local Wireless Access with High-level Security The Ericsson W3x may function as a WLAN access point for the wireless local network supporting WEP, WPA, and WPA2 with pre-

shared keys for WLAN security. In addition to the above, the Ericsson W35 also has the following features:

Voice Services The Ericsson W35 includes voice capabilities accessed over standard analog telephone line interfaces. Network services such as Prepaid Subscription, Caller ID (1st call only), CLIP, Call Waiting, Call Forwarding, and Multiparty Conference Calls are supported. Fax Service The Ericsson W35 supports fax over IP (T.38) functions using packet switched connection. If T.38 Fax is offered by the service provider as a service with the Ericsson W35, simply connect an ordinary fax machine to the Phone/Fax connector on the back of the unit and the fax will work without further configurations. Battery back-up For voice back-up purposes, an optional (available as an accessory) rechargeable battery-pack can be connected between the AC/DC adapter and the Ericsson W35. For more information about the Ericsson W3x product series, see www.ericsson.com/fwt 6 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 W3x Series Overview 2.5 Housing The housing on the Ericsson W3x is designed to be either wall mounted or standing on the desk by use of the provided table stand. Figure 3 - Mounting alternatives 2.5.1 Back Side Interfaces The back side of the Ericsson W3x includes the following interfaces:

Figure 4 Ericsson W35 back side 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 7 W3x Series Overview 8 The interfaces are described in the tables below:

Table 1 Ericsson W3x back side interfaces Label Ethernet 1-4 10-28VDC Reset Description Ethernet LAN connectors for connecting client PCs to the Ericsson W3x. Power input for connecting the provided power supply adapter or an optional external battery pack (Ericsson W35 only). A small hole in the housing used to restore the Ericsson W3x configuration to factory default settings. The following procedure resets all configurable values back to factory default, including the login user name and password. 1. Press the Reset button with the tip of a pen. The Standby button starts blinking. 2. Wait until the Standby button shows steady blue which indicates that the reset is finished. In addition to the above, the Ericsson W35 also includes interfaces for telephony and fax services. Note: Telephony and fax services must be supported by the subscription/network in order to work. The interfaces are described in the tables below:

Table 2 Additional back side interfaces on Ericsson W35 Label Phone Phone/Fax Description Telephone connector, for connecting an analog telephone to the Ericsson W35. Telephone/Fax connector, for connecting a fax machine to the Ericsson W35. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 W3x Series Overview 2.5.2 Left Side Interfaces The left side of the Ericsson W3x is equipped with the following interfaces:

Figure 5 Ericsson W3x left side The table below describes the interfaces:

Table 3 W3x left side interfaces Interface SIM Type SIM card slot USB USB-A Button Description SIM card slot for inserting a SIM card. Note: The Ericsson W3x must be disconnected from the power mains (or an optional battery removed) when inserting or removing the SIM card. USB connector for connecting USB device(s), e.g. a memory stick or a printer to the Ericsson W3x. For future use. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 9 W3x Series Overview 2.5.3 Right Side Interface The right side of the Ericsson W3x is equipped with an antenna connector

(type MCX) for connecting an optional external antenna. Figure 6 Ericsson W3x right side 2.5.4 2.5.4.1 Front Panel The front panel of the Ericsson W3x includes a signal quality indicator, LED indicators and a Standby button as described below. Signal Quality Indicator The signal quality indicator shows the quality of the signal from the mobile network. The more segments displayed in the bar graph, the stronger the signal. The symbol in the centre of the graph (

a mobile network connection and when a connection is established, it indicates the following:

) is blinking when searching for When 3G is displayed there is a connection to a UMTS network. 3G with a + sign indicates connection to a HSPA network. When the 3G symbol is unlit and the segment bar displays signal, there is a connection to a GSM/GPRS/EDGE (2G) network. 10 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 W3x Series Overview 2.5.4.2 W30 LED Indicators The following LED indicators are visible on the front of the Ericsson W30:

Figure 7 - Ericsson W30 LED indicators Table 4 Description of Ericsson W30 LED indicators Symbol Color Blinking

(blue) Off On (blue) Off Description Various alarm conditions exist that makes it impossible to establish a connection to the mobile network (and Internet). Information is specified on the Overview web page. No alarms. The Wireless LAN is activated. The Wireless LAN is not activated. On (blue) Off A connection to Internet is established. No Internet connection is established. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 11 W3x Series Overview 2.5.4.3 W35 LED Indicators The following LED indicators are visible on the front of the Ericsson W35:

Figure 8 - Ericsson W35 LED indicators Table 5 Description of Ericsson W35 LED indicators Symbol Color Blinking

(blue) Off Blinking

(blue) Off On (blue) Off On (blue) Off On (blue) Off Description New voice mail message(s) is available. No voice mail message(s) is available. Various alarm conditions exist that makes it impossible to establish a connection to the mobile network (and Internet). Information is specified on the Overview web page. No alarms. The Wireless LAN is activated. The Wireless LAN is not activated. A connection to Internet is established. No Internet connection is established. A connected telephone is off-hook. A connected telephone is on-hook. 12 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 W3x Series Overview 2.5.4.4 Built-in Ethernet Indicators The Ethernet LAN connectors (Ethernet 1-4) have two built-in indicators each. The left indicator shows the speed of data traffic between the Ericsson W25 and the connected client. If the speed is 100 Mbps, the indicator is green. When the indicator is unlit, the speed is 10 Mbps. The indicator to the right is yellow when a LAN connection is established and flashes to show data traffic activity. 2.5.4.5 Standby Button The Standby the Ericsson W3x has finished the start-up procedure. button at the bottom of the front shows steady blue when The button can be pressed to switch the Ericsson W3x to a standby (low-

power) mode (equal to when the Ericsson W35 is running on optional battery power). The button shows red when the unit is in standby mode and only phone services are available. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 13 Configuration and Management 3 Configuration and Management When the physical installation of the Ericsson W3x is finished (as described in the Quick Installation Guide), the internal Web User Interface (WUI) is available for configuration and status control. This chapter provides detailed information about configuration options and management of the Ericsson W3x using the WUI. The WUI is available in five languages; English, German, Spanish, French and Italian. Each page in the WUI includes country flags for the supported languages:

Click on a flag to change to the preferred language. 3.1 Access and Login to the Web User Interface The WUI can be accessed locally from a PC connected to either an Ethernet LAN port or to the wireless LAN interface. Note: First time setup must be done via an Ethernet port as the wireless LAN in the Ericsson W3x is disabled by default. Internet Explorer 5.0 or higher When accessing the web pages, the following web browsers are supported:

Safari 1.3 or higher Firefox 1.0 or higher Opera 8 or higher Start a web browser on a PC connected to the Ericsson W3x and type http://mbr or http://192.168.1.1 in the Address (URL) field. Note:

If you change the internal IP address on the Ericsson W3x, you have to use the new address to access the web pages. A start page is displayed in one of the following appearances depending on the operational status of the Ericsson W3x described in section 3.1.1 and 3.1.2. 14 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Configuration and Management 3.1.1 Enter PIN code The SIM card contains information about the subscription and is normally protected by a PIN (Personal Identification Number) code and a PUK

(Personal Unblock Key) code. Normally, you have to enter a PIN code to activate the SIM card. In some cases, however, PIN authentication is not required and it is possible to use the SIM card without entering a PIN code. The Enter PIN code page is displayed if a PIN code is required:

Figure 9 - Enter PIN code page Enter the PIN code (provided with the SIM card). You can also check Remember my PIN to have automatic SIM authentication in case of a system restart. Click the Apply button to save the settings. 3.1.2 Enter Password If a PIN code is not needed for SIM authentication, or if automatic SIM authentication is enabled, the Enter password page is displayed:

1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 15 Configuration and Management Figure 10 Enter password page Type user in the Password field and click the Log In button. For security purposes, it is recommended to change the default password, see section 3.11 Change Password. Note: You might, at any time, be redirected to the Enter password page without your intention if there are any problems with the connection to the mobile network and/or Internet. In this case, just enter the password and check the ALARMS section on the Overview page. After a successful login, the Overview page is displayed, see section 3.2 Overview. 3.1.3 Inactivity Timeout The WUI has an inactivity timeout set to 20 minutes. Before this timeout expires, it is preceded by a notification (displayed on top of the current displayed page) one minute before the automatic logout:

Figure 11 - Inactivity Timeout Warning The Cancel button can be clicked to abort the automatic logout. 16 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Configuration and Management When the timeout expires, the Enter password page is displayed with a notification about the automatic logout:

Figure 12 Enter password page (after inactivity timeout) Enter the Password and click Log In to make a new login. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 17 Configuration and Management 3.2 Overview The Overview page gives an overview of the settings on the Ericsson W3x as described below. Figure 13 - Overview page The Overview page provides the following functions:

The left-hand menu (visible on all web pages) that includes configuration topics for additional configuration described one by one in the following sections. The Configuration Wizard button which is the entrance to the step-

by-step configuration wizard recommended to be used for setting up your Wireless LAN. See section 3.3 Wireless LAN Configuration Wizard. The ALARMS section where detected error conditions are specified. See section 3.2.1 Alarms for more information. If an alarm occurs, the Alarm indicator (on the front of the Ericsson W3x) is blinking and a message is also sent to the Event log. See section 0 Event Log. 18 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Configuration and Management The NETWORK INFORMATION section where the most important connection status information is collected. This information (among others) is also found on the Internet and LAN web pages respectively. 3.2.1 Alarms The ALARMS section on the Overview page includes detected active error conditions. Events that generate an alarm are such that make it impossible to send or receive data, e.g. SIM card missing. If there are no alarms currently detected the text "No alarms detected"

is displayed. If an alarm is detected, the Alarm indicator on the Ericsson W3x front panel is blinking, and the corresponding cause is displayed according to the table below:

Table 6 - Alarm cause description Alarm cause No SIM card detected Invalid SIM card inserted No PIN code entered Incorrect PIN code entered SIM card blocked SIM card permanently blocked Alarm detection not working Unknown alarm Description There is no SIM card inserted, or the SIM card is not correctly inserted. The inserted SIM card is invalid No PIN code has been entered to activate the Internet and voice services. The entered PIN code is incorrect. The SIM card has been blocked (due to entering the wrong PIN code three times). The PUK is required to unblock the SIM card. The SIM card has been permanently blocked (due to entering the wrong PUK code ten times). A new SIM card is required. The alarm detection function is currently not working. An alarm that cannot be identified has occurred. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 19 Configuration and Management 3.2.2 Network Information The NETWORK INFORMATION section on the Overview page includes a selection of the Internet and LAN settings. This information (among others) is also displayed on the Internet and LAN pages respectively. The Internet information includes connection status and basic settings. Details about the following items are displayed:

Table 7 - Network information (Internet) description Text/symbol IP Address:

Connection:

Service provider:

Network registration:

Description The mobile network (HSPA, UMTS or GSM) signal quality available at the Ericsson W3x location. This signal quality affects the performance of the unit. If two or more bars are green, the connection is usually acceptable. The IP address automatically assigned to the Ericsson W3x by the mobile network. Note: If you require static IP addressing from your operator, contact them directly. The radio access technique currently used to enable Internet access. It can be HSPA, UMTS, EDGE, or GPRS. The name of, or other reference to, the mobile network operator. The current mobile network registration status:

- Not registered, not searching

- Registered, home network

- Searching

- Registration denied

- Unknown

- Roaming

- Limited Service The LAN section includes information about the following item:

Table 8 - Network information (LAN) description Text IP Address Description The LAN IP address of the Ericsson W3x. 20 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Configuration and Management 3.3 Wireless LAN Configuration Wizard The Wireless LAN Configuration Wizard guides you step-by-step through the basic setup for the Wireless LAN (WLAN). A Wireless LAN is a local network that communicates through wireless connections. Note: The wireless setup typically requires configuration of both the Ericsson W3x and the wireless clients. For more information about configuring wireless clients, see 6.2 Wireless LAN Settings. Click the Configuration Wizard button on the Overview page to start the wizard. 3.3.1 Enable the Wireless LAN The Ericsson W3x may function as a WLAN Access Point (AP) for the local network providing wireless client(s) with Internet and LAN access. Figure 14 Wireless LAN: WLAN Access Point page To enable connection of one or more wireless clients to the Ericsson W3x, select the Enable WLAN check box. Click Next to proceed. Note: The WLAN interface will not be activated until the complete configuration details are entered. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 21 Configuration and Management 3.3.2 Network Name All clients on the local wireless network share a common Service Set IDentifier (SSID) or network name. This name is required to establish connection between the Ericsson W3x and the wireless client(s), and to distinguish the wireless network from any other(s) that may be in use nearby. Only devices configured with the same network name as the one set on the Ericsson W3x can obtain access to it. Figure 15 Wireless LAN: Network Name (SSID) page The network name is case-sensitive (distinguish between uppercase and lowercase letters) and can be changed to any combination of numbers (0 9), letters (a z), and hyphens (-) with a maximum length of 32 characters. If the Enable SSID broadcast option is selected, your local wireless client(s) will find the network name when scanning the air. If not, the network name is hidden and has to be manually provided to the wireless client(s). If you want to change the preconfigured network name (MBR), type a new name in the Network name (SSID): field and also select if the SSID shall be hidden or not. Click Next to proceed. Wireless LAN Authentication All communication on the wireless LAN can be protected from potential intruders and eavesdroppers through standard authentication and encryption methods. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 3.3.3 22 Configuration and Management Authentication is used to restrict access to the wireless network and encryption is the translation of data into a form that cannot be easily understood by unauthorized users. The encrypted data can only be sent and received by users with access to a private encryption key. Note: Make sure that the operating system(s) and Wireless LAN interface(s) of the wireless client(s) support the selected authentication method. Figure 16 Wireless LAN: Authentication page Select one of the authentication methods from the Authentication drop-

down list. The available options are as follows:

Open (No security);

f you select Open as authentication method no client configuration is needed but be aware of that the WLAN will now be open without any kind of security. WEP-64, WEP-128 (Low security);

WEP (Wired Equivalent Privacy) is considered to be a low security option. WEP encrypted data is translated into blocks of either 64 bits length or 128 bits length. WPA, WPA2 (High security);

WPA (Wi-Fi Protected Access) and its successor WPA2 are the most reliable security options. WPA encryption uses the Temporal Key Integrity Protocol (TKIP) while WPA2 encryption follows the Advanced Encryption Standard (AES). AES offers a higher level of security and is approved for sensitive corporate and government data transmission. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 23 Configuration and Management WPA/WPA2 Mixed (High security) WPA/WPA2 Mixed enables connection of both WPA and WPA2 clients. Click Next to proceed. 3.3.3.1 Open If you select Open, the last page of the configuration wizard, where you can review and confirm your settings, is displayed:

Figure 17 WLAN Configuration Wizard Confirmation page To confirm the settings and close the Configuration Wizard, click the Finish button. You can use the Previous button to go back to previous pages and check your settings and/or make changes. If you click the Cancel button, the Configuration Wizard closes and no changes are saved:

Figure 18 - Cancel Configuration Wizard 24 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Configuration and Management 3.3.3.2 WEP Encryption Key WEP encrypted data can only be sent and received by users with access to a private encryption key. This means that each client on your wireless network has to be configured with the same key as in the Ericsson W3x. A 64-bit data encryption key includes 10 characters. A 128-bit data encryption key includes 26 characters. Only the hexadecimal numbers 0 to 9 and letters A to F are allowed. Figure 19 Wireless LAN: WEP (64 BIT) page Figure 20 Wireless LAN: WEP (128 BIT) page Enter an encryption key in the Encryption key field. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 25 Configuration and Management Click Next to proceed. 3.3.3.3 WPA/WPA2 Passphrase WPA and WPA2 authentication and encryption require a passphrase. Each client on your wireless network has to be configured with the same passphrase as in the Ericsson W3x. A WPA or WPA2 passphrase is case sensitive and consists of between 8 and 63 optional characters. It is recommended that the passphrase contains at least 20 characters. Figure 21 Wireless LAN: WPA page 26 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Configuration and Management Figure 22 Wireless LAN: WPA2 page Figure 23 - Wireless LAN: WPA/WPA2 Mixed page Type a unique passphrase in the Passphrase field. Note: Avoid using special characters (such as :, and ) when entering a pass phrase. Click Next to proceed. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 27 Configuration and Management 3.3.4 Wireless LAN Configuration Wizard Confirmation On the last page of the Configuration Wizard, the current settings are displayed:

Figure 24 WLAN Configuration Wizard Confirmation page To confirm the settings and close the Configuration Wizard, click the Finish button. You can use the Previous button to go back to previous pages and check your settings and/or make changes. If you click the Cancel button, the Configuration Wizard closes and no changes are saved:

Figure 25 - Cancel Configuration Wizard 28 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Configuration and Management 3.4 Internet The Internet web page includes status information and settings for the connection to the mobile network. Note: The information on this page may vary depending on product model and required authentication for Internet service setup. Figure 26 - Internet page 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 29 Configuration and Management 3.4.1 Mobile Network Connection Details The Ericsson W3x connects to the HSPA/UMTS (3G) network when it is available and uses the GSM/GPRS/EDGE (2G) network as fallback. Note: Your SIM card must support both 2G and 3G to have this capability. Check with your operator for any issues related to your local coverage for both 2G and 3G. The following information is displayed regarding the connection to the mobile network:

Table 9 - Mobile Network connection details Text/symbol Link Status:

Mode:

Connection:

Service provider:

Current APN:

Network registration:

IP Address:

Description The mobile network (HSPA, UMTS or GSM) signal quality available at the Ericsson W3x location. This signal quality affects the performance of the unit. If two or more bars are green, the connection is usually acceptable. The Internet access status, either Up or Down. If the link is up, connection is established. The protocol used for the Internet data traffic:

PPP (Point-to-Point Protocol). The radio access technique currently used to enable Internet access. It can be HSPA, UMTS, EDGE, or GPRS. The name of, or other reference to, the mobile network operator. The APN (Access Point Name) currently used. The current mobile network registration status, which can be one of the following:

- Not registered, not searching

- Registered, home network

- Searching

- Registration denied

- Unknown

- Roaming

- Limited Service The IP address automatically assigned to the Ericsson W3x by the mobile network. Note: If you require static IP addressing from your operator, contact them directly. 30 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Configuration and Management 3.4.2 3.4.3 DNS 1:

DNS 2:

The IP address to the primary DNS server. The IP address to the secondary DNS server. Traffic Statistics The TRAFFIC STATISTICS section on the Internet page includes information about the following items:

Table 10 - Traffic Statistics description Text Transmitted /

Received:

Error:

Overruns:

Dropped:

Transmitted /

Received current month:

Transmitted /

Received previous month:

Description The total size (and number) of transmitted/received data packets. The number of invalid data packets. The number of packets lost due to too many incoming data packets. The number of dropped data packets. The total size of transmitted/received data for the current month. The total size of transmitted/received data for the previous month. Note: The data size and packet counters have the upper limits of 4 GiB and 232 packets (more than 4 billion packets). When these limits have been reached, the counters wrap around to zero. Authentication Internet access requires authentication of the Ericsson W3x. Depending on the current Internet service setup, the authentication requests may differ. Your service provider provides the Ericsson W3x SIM card and details needed for authentication. The AUTHENTICATION section on the Internet page includes the following authentication details that may be required:

Table 11 - Authentication details Text PIN Description The PIN (Personal Identification Number) code, which 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 31 Configuration and Management Remember my PIN Auto APN APN (3G) APN (2G) PPP user name PPP password Authentication Protocol is used for SIM authentication. If enabled, SIM authentication is automatic and you will not have to enter the PIN code in case of a system restart. If enabled, the APN (Access Point Name) is automatically configured based on information on the SIM card. The 3G APN, which is a reference to the UMTS Internet access point on the service providers network. The APN usually has the format

<name.service_provider.country>. The 2G APN, which is a reference to the GSM Internet access point on the service providers network. The APN usually has the format

<name.service_provider.country>. The Point-to-Point Protocol Internet mode user name, which is used for user authentication. The Point-to-Point Protocol Internet mode password, which is used for user authentication. The authentication protocol (PAP or CHAP) to be used when PPP is used for authentication. If authentication is required because of a reset to factory default configuration, fill in the appropriate fields and click Apply to save the settings. Note: Only enter details you have received from your service provider and leave other fields empty. 3.4.3.1 Unblock SIM Card If three attempts have been made with an incorrect PIN code, the SIM card is blocked and the Unblock SIM button is displayed besides the PIN field. Figure 27 - Unblock SIM button 32 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Configuration and Management The PUK code is needed to unblock the SIM card. Click the Unblock SIM button to display the Unblock SIM page:

Figure 28 - Unblock SIM page Type the PUK code in the PUK field and type a new PIN code in the New PIN and Retype new PIN fields. Click OK to save the settings. Note:

If ten attempts have been made with an incorrect PUK, the SIM card is permanently blocked, and a new SIM card is required. 3.4.3.2 Unlock Operator Lock If the SIM card used in the Ericsson W3x is locked to a specific operator it cannot be replaced with any other SIM card without having received an unlock code from the service provider. If this is the case, and an invalid SIM card is inserted, the Unlock Operator Lock button is displayed besides the PIN field. Click the button to display the Unlock operator lock page:

Figure 29 - Unlock operator lock page Type the unlock code provided by the service provider in the Operator unlock code field and click OK to save the settings. The code consists of 10 characters. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 33 Configuration and Management 3.4.3.3 Change PIN If SIM authentication is verified, the PIN field cannot be edited. Instead the Change PIN button is displayed. Figure 30 - Change PIN button To change the PIN, click Change PIN to display the Change PIN page:

Figure 31 - Change PIN page Type the current and new PIN in the corresponding fields and click OK to save the settings. 3.4.4 Cellular Band Selection The CELLULAR BAND SELECTION section on the Internet page includes settings for manually selection of the frequency bands to use. Table 12 Cellular band selection details Text Region Description The drop-down list includes Preferred Roaming List

(PRL) regions. The PRL contains information regarding allowed systems (GSM/UMTS) and bands. This information is used by the Ericsson W3x during the system selection and acquisition process, initially and when the Ericsson W3x is roaming. By setting a specific region, the Ericsson W3x favors bands within this region. 34 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Configuration and Management Included regions in the list are:

Global Europe/Rest of the World North America Australia Japan H3G, W2100, G900/1800 Note: A restart is required if changing this setting. Select the frequency bands to be used for a 3G mobile connection; 850, 1900, 2100. Select the frequency bands to be used for a 2G mobile connection; 850, 900, 1800, 1900. 3G Settings 2G Settings 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 35 Configuration and Management 3.5 LAN The LAN (Local Area Network) page includes settings for the connections between the Ericsson W3x and other local devices, and status on the physical LAN ports. Figure 32 - LAN page 3.5.1 LAN IP Address The LAN IP address and subnet mask of the Ericsson W3x is used for connections to clients on the LAN/WLAN. The following configuration options are displayed on top of the LAN page:

36 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Configuration and Management Table 13 - LAN page description Text IP address:

Subnet mask:

Description The LAN IP address of the Ericsson W3x. The subnet mask, which determines the range of IP addresses on the subnet. The LAN IP address and subnet mask can be changed, but before you do this, consider the following:

Make sure that the new address is not included in the DHCP server IP address range, displayed in the DHCP Server section. The default range is 192.168.1.2 192.168.1.100. Make sure that the DHCP server IP address range is included in the new subnet. If you want to change the subnet not to include the DHCP IP address range, you first have to disable the DHCP server. If port forwarding rules have been configured, those settings have to be removed before changing the IP address or subnet mask. For information, see section 3.7.3 Port Forwarding. To change the LAN IP address or subnet mask of the Ericsson W3x, type the new values in the corresponding fields and click Apply to save the settings. Note:

If you change the LAN IP address while connected to the WUI, you will be disconnected. You have to redirect the web browser to the new address in order to confirm the new settings. Type the new LAN IP address in the Address (URL) field and press Enter. DHCP Server The Ericsson W3x incorporates a DHCP (Dynamic Host Configuration Protocol) server which dynamically assigns IP addresses to devices on the LAN/WLAN whenever they are switched on. The DHCP server also puts the hostname, supplied by the client DHCP request, in the local DNS

(Domain Name System/Service) proxy. The DNS proxy contains a small database of local host names and addresses supplied by client DHCP requests. In addition it also caches requests to remote DNS servers. The following configuration options are displayed in the DHCP server section on the LAN page:

3.5.2 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 37 Configuration and Management Table 14 - DHCP Server configuration options Text Enable DHCP server IP address range from:

IP address range to:

Lease Time [sec]:

Description Select this checkbox to enable the DHCP server. Note: If you already have a DHCP server on your network, you should disable this feature in the Ericsson W3x. The IP addresses that can be assigned to LAN/WLAN clients are collected from a predefined range of available IP addresses. The preconfigured range from 92.168.1.2 to 192.168.1.100 is suitable for most local networks. The DHCP server uses the concept of a lease, that is the amount of time that a given IP address will be valid for a specific device. If the lease time expires and the device is still connected, the lease is automatically renewed. The preconfigured lease time is 7200 seconds

(2 hours) and a valid value must be within the range 60 and 2147483647 seconds. Note:

If you want to configure a connected device with a static IP address, make sure that the address is outside the DHCP server IP address range. Before changing any of the DHCP server settings, read the following:

The DHCP server IP address range has to be on the same subnet as the LAN IP address on the Ericsson W3x. The DHCP server IP address range must not include the LAN IP address on the Ericsson W3x. If port forwarding rules have been created, those settings have to be removed before changing the DHCP server IP address range. For more information, see section 3.7.3 Port Forwarding. To change the DHCP server settings, type the new values in the corresponding fields and click Apply to save the settings. 38 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Configuration and Management 3.5.2.1 Leases When there are clients connected to the Ericsson W3x that have been assigned IP addresses from the DHCP server they are presented in the DHCP Server section as in the example below:

Figure 33 - DHCP server leases If not, the text There are no leases at this time is displayed. 3.5.3 LAN Port Status The LAN PORT STATUS section on the LAN page shows the link status of each Ethernet LAN port (Ethernet 1 - 4) on the Ericsson W3x. Figure 34 - LAN Port Status The status for each port is either green (Up) when a device is connected to the port or red (Down) when no device is connected. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 39 Configuration and Management 3.6 Wireless LAN A Wireless LAN (WLAN) is a local network that communicates through wireless connections. The Ericsson W3x can be used as a WLAN Access Point (AP), connecting to wireless PCs according to the IEEE standard 802.11b/g, providing Internet and LAN access. The WLAN settings are displayed on the Wireless LAN page. Figure 35 - Wireless LAN page 3.6.1 Enable WLAN To enable the wireless LAN on the Ericsson W3x select the Enable WLAN check box and click the Apply button to save the setting. To ensure the security of your Wireless LAN, you are recommended to change the default settings for SSID and authentication. Note: The wireless setup typically requires configuration of both the Ericsson W3x and the wireless client(s). For more information on configuration of wireless clients, see section 6.2 Wireless LAN Settings. 40 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Configuration and Management 3.6.2 3.6.3 3.6.4 3.6.5 Region Wireless devices are thoroughly regulated and the countries have slightly different regulations. Therefore, the geographical region where the Ericsson W3x is used must be stated to make sure the correct radio frequencies are used when transmitting data. Select the geographical region in which you reside from the Region drop-

down list and click Apply to save the setting. Radio Channel The radio channel must be in accordance with the previous set region and only channels that are allowed in the configured region are available in the Radio channel drop-down list. By selecting Auto (recommended) the radio in the Ericsson W3x will automatically scan each valid channel and choose the one with least interference. Select either Auto or a specific channel number from the Radio channel drop-down list and click Apply to save the setting. Transmit Power [dBm]

To avoid interference with other wireless networks, the transmit power level can be reduced. If you want to change the transmit power level according to your specific conditions, select an appropriate level from the Transmit power [dBm] drop-down list and click Apply to save the setting. Data Rate According to wireless LAN standards and the IEEE 802.11 protocols there are different data rates available for different modes. From the Data rate drop down list there are the following modes available:

B-Mode Only (supporting IEEE 802.11b clients with a maximum data rate of 11 Mbit/s) G-Mode Only (supporting IEEE 802.11g clients with a maximum data rate of 54 Mbit/s) B/G-Mixed Mode (supporting both IEEE 802.11b/g clients as described above) Legacy B-Mode (supporting IEEE 82.11b legacy clients). 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 41 Configuration and Management Select an appropriate data rate from the Data rate drop down list according to what is supported by the wireless clients that should connect. Click Apply to save the setting. 3.6.6 Scan for Wireless Networks If you want information about adjacent wireless networks, click the Scan for wireless networks button. A scanning is started and when finished, information about wireless networks is presented as in the example below:

Figure 36 - Scan for wireless networks page The list displays the following information about wireless networks that are nearby:

Table 15 - Scan for wireless networks description Text MAC Address Network Name Channel RSSI Description The MAC address of the access point for the WLAN. The network name (SSID) of the WLAN. The radio channel used by the WLAN. The RSSI (Received Signal Strength Indicator) which is a link indication expressed in dBm to show the signal strength of the wireless network. This information can be of help when deciding which channel to use. Click Back to return to the Wireless LAN page where you can select a desired channel. 42 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Configuration and Management 3.6.7 Network Name (SSID) All clients on the WLAN share a common network name or SSID (Service Set IDentifier). This name is required to establish connection between the Ericsson W3x and other wireless client(s) and to distinguish the WLAN from any other(s) that may be in use nearby. Only clients configured with the same network name (SSID) as the one set on the Ericsson W3x can obtain access to it. Note:

It is recommended to change the preconfigured network name MBR to something else that makes it harder for unauthorized persons to access your wireless network. The following settings concerning the network name are displayed and can be modified on the Wireless LAN page:

Table 16 - Network name description Text Network name (SSID):

Enable SSID broadcast Description The network name (SSID) of the wireless network. The network name is case-sensitive

(distinguish between uppercase and lowercase letters) and can be changed to any combination of numbers (0-9), letters

(a-z), and hyphens (-) with a maximum length of 32 characters. If Enable SSID broadcast is checked, the SSID is continuously broadcasted and any nearby wireless client(s) will find it when scanning the air. If the checkbox is cleared, the SSID will be hidden and in this case the name has to be provided manually to every wireless client where access is to be granted. To change settings for the Network Name (SSID), type the new values in the corresponding fields and click Apply to save the settings. 3.6.8 WLAN Security All communication on the wireless network can be protected using different authentication and encryption methods. The most common is to encrypt the WLAN using an encryption method such as WEP, WPA and WPA2. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 43 Configuration and Management Which authentication and encryption method that should be used depends on what is supported by the connected wireless client(s). Note: Each wireless client must be configured to use exactly the same security mode and key/passphrase as the Ericsson W3x or they will not be able to connect. In the Authentication drop-down list you select which type of authentication/encryption you want to use for your WLAN. The following subsections describe the authentication methods supported by the Ericsson W3x. Open (No security) If you select Open as authentication method no client configuration is needed but be aware of that the WLAN will now be open without any kind of security. For example, it is now possible for anyone with a computer and a wireless interface card to connect to the Ericsson W3x at any time and having access to both your home network and Internet connection. WEP and WEP Encryption Key (Low security) WEP (Wired Equivalent Privacy) is considered to be a low security option. The data is encrypted into blocks of either 64 bits length or 128 bits length. WEP encrypted data can only be sent and received by users with access to a private encryption key. This means that each client on your wireless network has to be manually configured with exactly the same key as the one entered in the Ericsson W3x in order to allow encrypted data transmissions. WEP-64 bit data encryption requires a key including 10 characters. Only hexadecimal numbers 0-9 and letters a-f (uppercase or lowercase) are allowed. WEP-128 bit data encryption requires a key including 26 characters. Only hexadecimal numbers 0-9 and letters a-f (uppercase or lowercase) are allowed. Enter an encryption key in the Passphrase / Key field and click Apply to save the settings. WPA/WPA2 and Passphrase (High security) WPA (Wi-Fi Protected Access) and its successor WPA2 are the most reliable security options. WPA encryption uses the TKIP (Temporal Key 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 3.6.8.1 3.6.8.2 3.6.8.3 44 Configuration and Management Integrity Protocol) while WPA2 encryption follows AES (Advanced Encryption Standard). AES offers a higher level of security and is approved for sensitive corporate and government data transmission. WPA/WPA2 Mixed enables connection of both WPA and WPA2 clients. WPA and WPA2 authentication and encryption require a passphrase. A passphrase is a sequence of words or other text and is similar to a password in usage, but is generally longer for added security. Each client on your wireless network has to be configured with exactly the same passphrase as the one entered in the Ericsson W3x in order to allow encrypted data transmission. A WPA or WPA2 passphrase is case sensitive (distinguish between uppercase and lowercase letters) and consists of between 8 and 63 characters. It is recommended that the passphrase contains at least 20 characters. Enter a passphrase in the Passphrase / Key field and click Apply to save the settings. Note: Avoid using special characters (such as :, and ) when entering a passphrase. Connected Devices The CONNECTED DEVICES list on the Wireless LAN page includes the MAC (Media Access Control) addresses of all wireless clients currently connected to the Ericsson W3x. Whitelist A common method of restricting WLAN access is to specify the MAC address(es) in a whitelist for those computers to be granted access to the WLAN. This kind of whitelist is also known as MAC Association or MAC Access list. Up to 20 MAC addresses for wireless clients can be added to the whitelist. Once the whitelist has been enabled, only clients with an associated MAC address are allowed to connect to the WLAN. Note: This feature does not require any configuration of clients, but it is recommended that some kind of encryption (WEP, WPA/WPA2) is used in combination with the whitelist. 3.6.9 3.6.10 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 45 Configuration and Management 3.6.10.1 Add Client(s) to the Whitelist To add a client to the whitelist, you can either copy/paste a MAC address from the CONNECTED DEVICES list or type the clients MAC address in the field below WHITELIST and click Add . The MAC address has the form of xx:xx:xx:xx:xx:xx, where x is a hexadecimal number (0-9 and/or letters a-f), for example 00:80:37:8c:10:46. Check Enable whitelist to activate the feature and click Apply to save the settings. To delete a MAC address from the whitelist, click the Delete button next to the MAC address to delete. 3.6.10.2 Find a Wireless Client MAC Address The MAC address for a WLAN adapter is normally found on the product label. For internal wireless PCI cards running on Windows platform, the command ipconfig /all (run from a Command Prompt window) can be used to display the MAC address (displayed as Physical Address against the network adapter). For example:

Wireless LAN adapter Wireless Network Connection:

Media State . : Connected Description . : Intel(R) PRO/Wireless 3945ABG Physical Address. : 00-19-D2-39-14-54 DHCP Enabled . : Yes Autoconfiguration Enabled . : Yes 46 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Configuration and Management 3.7 NAT The Ericsson W3x includes a NAT (Network Address Translation) service. With this service several computers on a LAN/WLAN can share the same Internet connection using a single public IP address. Devices on the LAN/WLAN use dedicated private IP addresses, which cannot be used on the Internet. When a computer on the LAN/WLAN want to send a data package to the Internet, its IP address is automatically translated by NAT to an external (public) IP address allowed on the Internet. When a reply receives to this external IP address, it is translated back to the origin private IP address to be able to found its way back to the sending computer on the LAN/WLAN. In this way, details about the local devices remain private and it is not possible to access a local computer on the LAN/WLAN directly from the Internet. The NAT page includes the following settings:

Figure 37 - NAT page 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 47 Configuration and Management 3.7.1 3.7.2 UPnP IGD The Ericsson W3x supports the Universal Plug and Play (UPnP) Internet Gateway Device (IGD) standard. UPnP IGD is used to provide automatic port forwarding allowing communication between certain Internet applications and the local network. When UPnP IGD is enabled, programs like MSN Messenger and most network enabled games are allowed to pass the NAT service. UPnP IGD is enabled by default, but if you want to disable the feature, clear the Enable UPnP IGD check box and click Apply to save the settings. Application Level Gateways From a security perspective, certain Internet applications, for example FTP applications that open additional ports upon transfer, are especially problematic to handle. An Application Level Gateway (ALG) provides a translation and transportation service for such a specific application. Incoming data packets are checked against existing NAT and packet filtering rules, IP addresses are evaluated and a detailed packet analysis is performed. If necessary, the contents of a packet are modified and if a secondary port is required, the ALG will open one. The Ericsson W3x includes ALG support for the following applications:

Table 17 - ALG Supported Applications Application File Transfer Protocol (FTP) Trivial File Transfer Protocol (TFTP) Point-to-Point Tunneling Protocol (PPTP) Session Initiation Protocol (SIP) Real Time Streaming Protocol (RTSP) Protocol TCP UDP TCP/UDP TCP/UDP TCP/UDP Port number 21 69 1723 5060 554 The ALG for each application does not require additional configuration. The supported ALGs can be enabled and disabled individually. To disable an ALG, clear the corresponding check box and click Apply to save the settings. 48 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Configuration and Management 3.7.3 Port Forwarding Port forwarding is used to allow an external user to access a service residing on a server connected to the LAN (to cross the NAT border). It enables access to servers on the LAN from the Internet (e.g. Web server) and also enables applications to work from the LAN (e.g. games, voice and chat) to the Internet. Note: Port forwarding requires that the Ericsson W3x has a public IP address for Port Forwarding requests from the Internet to be handled correctly. This IP address is displayed on the Overview page as the Internet: IP address. A private IP address usually begins with 10, 172, or 192. In this case, no incoming access from the Internet is allowed. For more information on public and private IP addresses, contact your service provider. When a computer on the Internet sends data to the public IP address of the Ericsson W3x, it needs to know what to do with the data. A port forwarding rule tells the Ericsson W3x which computer on the local area network to send the data to. The PORT FORWARDING section on the NAT page includes the following information about port forwarding rules:

Table 18 - Port Forwarding description Text NAT Port Server IP Server Port Protocol Delete Edit Description The NAT port number that the data traffic is allowed to be transported on. The IP address of the destination server on the LAN. The port number on the destination server which identifies the type of service that is directed, for example web service on port 8080. The protocol to be used for the service; TCP or UDP. Click on the button to delete the port forwarding rule. Click on the button to edit the port forwarding rule. 3.7.3.1 Add a Port Forwarding Rule To add a new port forwarding rule, click the Add Instance button. The Add Port forwarding Instance page is displayed:

1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 49 Configuration and Management Figure 38 - Add Port forwarding Instance page Select a Protocol from the drop-down list and type the appropriate values in NAT Port, Server IP, and Server Port fields and click Apply to save the setting. Below are some examples of common applications and corresponding server port they use for network access. The NAT Port has often the same value as the Server Port value. Exceptions are made when the same applications are used on many clients on the LAN/WLAN, where each Server IP value needs to be unique and differ from the NAT Port value. Table 19 - Common applications server ports Application MSN Messenger Server Port 6901 Unreal Tournament 2004 NetMeeting Quake III 7777, 7778, 7787, 28902 1720, 1503 27669 (+1 for each player) Note:

If multiple ports or port ranges are required, create a new port entry for each port or port range. 3.7.3.2 Port Forwarding Example In the following example, port forwarding is used to allow incoming access

(from the external network (Internet)) to an internal web server (on the LAN/WLAN). The TCP protocol is used for data traffic. The NAT port 80 on the Ericsson W3x is open and the destination computer on the LAN with static server IP address 192.168.1.101 has appointed the server port 8080 to be used. 50 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Configuration and Management Figure 39 - Port forwarding example 3.7.3.3 Edit Port Forwarding Rule To edit a port forwarding rule, click Edit next to the rule to edit. The Edit Port forwarding page is displayed:

Figure 40 - Edit Port forwarding page Change one or more value(s) in the Protocol, NAT Port, Server IP, or Server Port field(s) and click Apply to save the settings. 3.7.3.4 Delete Port Forwarding Rule To delete a port forwarding rule, click Delete next to the rule to be deleted. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 51 Configuration and Management 3.8 File and Printer Sharing The Ericsson W3x supports local network storage and printer sharing through the USB port. If an external USB hub is connected, the Ericsson W3x supports connection of up to two storage devices and one printer at the same time. The Sharing page displays information about connected USB device(s):

3.8.1 Figure 41 - Sharing page How it Works The Ericsson W3x uses Samba (www.samba.org) as the base to implement file and printer sharing through SMB/CIFS. SMB and CIFS are the protocols used by Microsoft for sharing and the service is called smb on the Ericsson W3x. Linux Kernel auto detection of USB devices is used as part of the automatic configuration of the storage and printer sharing. When a new USB device (storage or printer) is detected, the Ericsson W3x automatically creates configuration files for Samba containing the new device. It then makes the smb service use the new configuration, 52 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Configuration and Management 3.8.1.1 3.8.2 thereby sharing the USB device via the SMB/CIFS protocol. This process is totally automatic and there are no configuration parameters that can be set, other than renaming the shared resources. The Ericsson W3x uses a relatively low powered processor and is not designed to be a multi tasking platform. This means that you may experience problems during high load situations such as simultaneously downloading a large file through the mobile network and printing a large document or copying a large file to/from a shared storage device mounted on the Ericsson W3x. Dont expect to have full performance on all simultaneous tasks. Safe Removal of a USB Device Before removing a USB device from the Ericsson W3x wait until the activity LED (if any) on the device stops blinking or wait some 30 seconds to be sure there is not any ongoing/remaining write operations to be made. Host Name and Workgroup All devices on the LAN/WLAN that want to access a USB shared storage device or printer must belong to the same workgroup as the Ericsson W3x. The following information can be changed on the Sharing page:

Table 20 - Sharing information Text Host name:

Workgroup:

Description The name of the Ericsson W3x on the local network. The name of the group of devices sharing the same resources on the local network. To change the host name or workgroup, type the new name in the corresponding field and click Apply to save the settings. For information about setting up a connection from a PC to a shared device, follow the instruction in section 6.3.3 Set Up a Connection to a Storage Device or section 6.3.4 Access a Shared Printer. 3.8.3 File Sharing When a USB storage device is connected to the Ericsson W3x the included files are shared with all devices on the local network (LAN/WLAN) and all local users have full access to the shared files. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 53 Configuration and Management Note: Only the first partition of the storage device will be automatically mounted and shared through the smb service. The file system on a shared partition needs to be of a supported type;

otherwise the automatic mounting of the device will not work. Currently the supported types are:

FAT; Microsoft legacy file system from MS-DOS with 8.3 character filename FAT32; Microsoft Windows 95 file system based on FAT but with long file name ext2; Second extended file system, the standard Linux file system. ext3; Like ext2, but with journaling support. When a storage device is connected to the USB port on the Ericsson W3x, information about the device is displayed in the SHARED STORAGE DEVICES section on the Sharing page. If this page is open when you connect the device, a refresh of the page may be required for the new information to be displayed. Table 21 - Shared storage devices description Text Storage device:

Share name:

Description The manufacturers name of the device. The name of the shared resource used when accessing the device from a PC on the LAN/WLAN. To give a shared device a specific name, type a name in the corresponding Share name field and click Apply to save the setting. Note:

If a Share name includes more than 12 characters or has embedded spaces, the share name will not be visible in Windows 95, 98 or ME clients. To access shared files from a PC using Windows 2000 or XP, follow the instructions in section 6.3.2- Access a Shared USB Storage Device. Printer Sharing When a printer is connected to the USB port on the Ericsson W3x, it is automatically shared over the LAN/WLAN using SMB/CIFS protocol. The smb service only performs protocol conversion between SMB/CIFS and the local printer. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 3.8.4 54 Configuration and Management When a printer is connected to the USB port on the Ericsson W3x, information about the printer is displayed in the SHARED PRINTER section on the Sharing page. If this page is open when you connect the printer, a refresh of the page may be required for the new information to be displayed:

Table 22 - Shared printer description Text Printer Share name Description The manufacturers name of the device. The name of the shared printer used when accessing it from a PC on the LAN/WLAN. To give a network printer a specific name, type a name in the Share name field and click Apply to save the setting. Note:

If a Share name includes more than 12 characters or has embedded spaces, the share name will not be visible in Windows 95, 98 or ME clients. To access a shared printer from a PC using Windows 2000 or XP, follow the instructions in section 6.3.4 Access a Shared Printer. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 55 Configuration and Management 3.9 System The System page includes system information and management functions, used to update and restore the Ericsson W3x. Note: The information on this page may vary depending on product model and services included in the subscription. Figure 42 - System page 56 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Configuration and Management 3.9.1 Basic System Information The table on top of the page includes basic system information about the Ericsson W25. The following information is displayed:

Table 23 Basic System Information Text Product Product Id:

Serial Number:

Boot Loader:

Application Software:

UMTS Boot Loader:

UMTS Application Software:

Ethernet MAC Address:

WLAN MAC Address:

IMEI:

Description The product name. The product identification. The unique serial number of the unit. The ID and version of the boot loader software. The ID and version of the application software. The ID and version of the UMTS boot loader software. The ID and version of the UMTS application software. The MAC address of the external Ethernet interface. This MAC address can also be found on the product label on the bottom of the unit. The MAC address of the WLAN interface. This MAC address can also be found on the product label on the bottom of the unit. The unique IMEI number of the unit. This number can also be found on the product label on the bottom of the unit. 3.9.2 3.9.2.1 Configuration Backup and Restore The current running configuration of the Ericsson W3x can be saved into a backup copy (locally stored on a PC). This backup copy can then be used for restoring the configuration to a specific state. Back Up Current Configuration To back up the current running configuration, click the Back Up button in the CONFIGURATION BACKUP AND RESTORE section on the System page. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 57 Configuration and Management Follow the instructions on the screen to select a location for the configuration file. Note: Do not modify a configuration file. If you do, the file might be invalid and not accepted if you want to make a restore. All configuration changes should be made on the web pages. 3.9.2.2 Restore from Backup File In case of a system failure or a corrupted configuration, the system can be restored from a previously stored backup file. To restore from a backup file, click the Browse button in the CONFIGURATION BACKUP AND RESTORE section on the System page to locate the configuration file. When a file has been selected it is displayed in the text field below Restore to previous settings from a configuration backup. Click Restore to restore the configuration. When finished, a confirmation message is displayed:

Figure 43 - Configuration Restore Confirmation Click OK to return to the System page. 3.9.3 System Restart You can at any time restart the Ericsson W3x. The restart does not result in any configuration changes. To restart the Ericsson W3x, click Restart in the RESTART section on the System page. During the restart process the following information is displayed:

58 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Configuration and Management Figure 44 - Restart Progress Message When the restart is completed you have make a new login to the WUI. Type http://192.168.1.1 in the Address (URL) field to display the User login page. 3.9.4 Software Update New Ericsson W3x software versions can be installed from a local file. First, make sure that the new software file is available on your PC. Then click Browse in the SOFTWARE UPDATE section on the System page to locate the file. The selected file will be displayed in the Update the system with new software field. Click Upgrade to start the installation. During the installation process, a new window showing the progress is displayed:

Figure 45 - Software Update Initiated page Figure 46 - Software Update Progress page When the update is completed, the following window is displayed:

1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 59 Configuration and Management Figure 47 - Software update complete Click the Close window button to close the window. The following page is displayed:

3.9.5 Figure 48 - Software update complete page Click the Restart button to restart the Ericsson W3x. Factory Reset The Ericsson W3x configuration can be reset to its factory default settings from the System page. Note:

If the WUI is not accessible, a reset to factory default settings can also be done using the Reset button on the unit. See section 7.2 Reset to Factory Default Settings. To reset the configuration to factory default settings, click Reset in the FACTORY RESET section on the System page. Note: This procedure resets ALL configurable values back to default settings, including the login password (user). Before the reset starts, you will get the following question:

60 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Configuration and Management Click OK to start the reset or Cancel to abort the reset and return to the System page. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 61 Configuration and Management 3.10 Event Log On the Event Log page, a list of the events that has been sent to the log on the Ericsson W3x is displayed:

Figure 49 - Event Log page Each row in the log list displays the time and date when an event was reported to the log, the type of the event, and a brief statement indicating its cause. Note:

If the actual time is not available, the timestamp is set to Jan 1 00:00:00 when the Ericsson W3x is restarted. This will change to actual time when available. 62 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Configuration and Management The system logging information is written to 3 files in the system and these files are rotated in a circular fashion. The files are not saved to flash memory and will be lost when rebooting the system or when power is disconnected. To view only a selection of the log events in the list, select a filter level from the Display list. Available log levels are Alarms only and All. The Alarms only log level corresponds to the Alarm Ericsson W3x and the information in the ALARMS section on the Overview page. indicator on the Click Refresh to update the list with new information. The most recent logs are listed at the bottom of the list. Persistent Logging If persistent logging is enabled, the log files are written to flash memory in two alternating files meaning they will remain after a system restart or power failure. Note: Persistent logging should only be used for debugging purposes since it consumes flash memory. To enable this feature, select the Persistent logging check box on the Event Log page and click Apply to save the setting. 3.10.1 3.11 Change Password On the Change Password page the password used for logging in to the web pages can be changed. For security reasons you are recommended to change the preconfigured password. Figure 50 - Change Password page 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 63 Configuration and Management Type the current password in the Current Password field. If it is the first time you change the password, the password is user. Type a new password in the New Password and Retype New Password fields. A password can include up to eight (8) characters (letters and/or numbers). Note: The password is case-sensitive (distinguish between uppercase and lowercase letters). Save the new password by clicking OK . 3.12 Logout To logout from the Ericsson W3x web pages, click Logout in the left-hand menu. When the logout is completed, the Enter password page is displayed. 64 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Telephony and Fax (W35 only) 4 Telephony and Fax (W35 only) A telephone and/or a fax machine can be connected to the Ericsson W3x via the Phone or Phone/Fax connectors on the back of the unit. Note: A fax must be connected to the Phone/Fax connector and the operator needs to support a fax over IP function. The telephony and the fax services will work without any further configurations but must be supported by the subscription/network in order to work. If you experience problems see the trouble shooting section 7.7 Telephony and Fax Service. 4.1 SIM Authentication It is possible to enter the PIN code for SIM authentication via a telephone connected to the Ericsson W35 (instead of the WUI). Follow the steps below to enter the PIN code using a telephone. The PIN required and PUK required tones are described in Table 24 Information Tones on the next page. 1. Pick up the telephone handset. If you hear the dial tone, you do not need to enter any PIN. If you hear the specific PIN required tone, proceed to step 2. 2. Dial * <PIN> #

If the PIN is correct, you will hear the normal dial tone, which indicates that the voice service is activated and that it is possible to make phone calls. If the PIN is incorrect, you will hear the PIN required tone again. Repeat step 2. Note:

If three attempts have been made with an incorrect PIN, the SIM card is blocked and you will hear a new tone, indicating that the PUK is required to unblock the SIM card. To unblock the SIM card, dial the following sequence:

* <PUK> * <new PIN> * <new PIN> #

1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 65 Telephony and Fax (W35 only) If the PUK is correct and the new PIN codes agree, you will hear the normal dial tone, which indicates that the voice service is activated and that it is possible to make phone calls. Remember the new PIN for future use. If the PUK is incorrect or the new PIN codes do not agree, you will hear the PUK required tone again. Repeat the unblock SIM card sequence above. Note:

If ten attempts have been made with an incorrect PUK, the SIM card is permanently blocked and a new SIM card is required. Contact your service provider. Information Tones The Ericsson W35 generates information tones in your telephone handset, thus providing the same characteristics as the one given by the traditional fixed line network. The following table describes the nature of the unique information tones you will get when using the Ericsson W35. Table 24 - Information Tones Name PIN required PUK required Nature 50 50 200 200 Repeating 200 ms tone at regular 50 ms intervals. 50 50 50 50 Repeating 50 ms tone at regular 50 ms intervals. Description SIM authentication is required to enable the voice service. The SIM card is blocked. The PUK and a new PIN are required to unblock the SIM card. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 4.2 66 Battery (W35 only) 5 Battery (W35 only) The Ericsson W35 can be powered with a rechargeable battery pack to provide voice service redundancy in the event of a total mains power failure. When mains powered, the Ericsson W35 will keep the battery charged. Note: The battery is not fully charged when delivered. The charging time for an empty battery is about 4 hours. The battery will not charge if the environment temperature is above 40 degrees Celsius, due to over heating protection. 5.1 Installation of the Battery The battery is available as an accessory and is inserted between the AC/DC adapter and the Ericsson W35. Battery pack Figure 51 - Battery pack and power adapter 5.2 Battery Function If a power failure occurs the Ericsson W35 automatically switches over to battery operation. In order to extend the battery time only voice services is available. Data services, such as USB, Ethernet and Wireless LAN functions will be unavailable. The Standby powered by battery (or when the Standby button has been pressed). button on the front of the Ericsson W3x is red when The stand by time is up to 4 hours if no telephone calls are made. Talk time is typically 3 hours. Battery time depends on the mobile network signal quality, battery age, and environmental temperature. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 67 PC Configuration 6 PC Configuration 6.1 6.1.1 6.1.1.1 The connection to the Ericsson W3x may require specific PC configuration. This chapter includes instructions on how to configure Internet Protocol (IP) settings as well as establish wireless connection(s) with the Ericsson W3x. The descriptions include examples from Windows XP and 2000. If you use another operating system, please refer to the system documentation or online help. IP Settings The Ericsson W3x automatically assigns the IP settings to your PC(s). You only need to configure the PC(s) according to the instructions below to accept the information. In some cases however, you may want to configure IP settings manually. See section 6.1.2 Configuring Static IP Address. If you want to allow wireless PCs to access your device, you also have to follow the instructions in section 6.2 Wireless LAN Settings. Obtain IP Settings Automatically Follow the instructions that correspond to the operating system installed on your PC. Windows XP 1. In the Windows task bar, click the Start button, and then click Control Panel. The Control Panel window is displayed. 2. If you are using Category View, Click Network and Internet Connections and then Network Connections. If you are using Classic View, double-click Network Connections. The Network Connections window is displayed. 3. Double-click the icon corresponding to your network interface card

(NIC). This icon is usually labeled Local Area Connection. The Local Area Connection Properties window is displayed with a list of currently installed network items. 4. Select Internet Protocol TCP/IP and ensure that the check box beside the text is selected. Click Properties . 68 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 PC Configuration 5. In the Internet Protocol (TCP/IP) Properties window, select Obtain an IP address automatically and Obtain DNS server address automatically. 6. Click OK twice to confirm your changes and close the windows, and then close the Control Panel window. 6.1.1.2 Windows 2000 First, check for the IP protocol and, if necessary, install it:

1. In the Windows task bar, click the Start button, point to Settings, and then click Control Panel. 2. Double-click the Network and Dial-up Connections icon. 3. 4. 5. In the Network and Dial-up Connections window, right-click the Local Area Connection icon, and then click Properties. The Local Area Connection Properties dialog box is displayed with a list of currently installed network components. If the list includes Internet Protocol (TCP/IP), then the protocol has already been enabled. Skip to step 11. If Internet Protocol (TCP/IP) does not display as an installed component, click Install . In the Select Network Component Type dialog box, select Protocol, and then click Add . 6. Select Internet Protocol (TCP/IP) in the Network Protocols list, and then click OK . You may be prompted to install files from your Windows 2000 installation CD or other media. Follow the instructions to install the files. 7. If prompted, click OK to restart your computer with the new settings. Next, configure the PCs to accept IP information assigned by the Ericsson W3x:

8. In the Windows task bar, click the Start button, point to Settings, and then click Control Panel. 9. Double-click the Network and Dial-up Connections icon. 10. In the Network and Dial-up Connections window, right-click the Local Area Connection icon, and then click Properties. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 69 PC Configuration 11. Select Internet Protocol TCP/IP and ensure that the check box beside the text is selected. Click Properties . 12. In the Internet Protocol (TCP/IP) Properties window, select Obtain an IP address automatically and Obtain DNS server address automatically. 13. Click OK twice to confirm your changes and close the windows, and then close the Control Panel window. 6.1.2 Configure Static IP Address Most users do not need to configure static IP settings. Automatic configuration is appropriate in most cases. For information about static IP configuration, see the operating system documentation or online help. Note: Make sure that the IP address of the client is on the same subnet as the Ericsson W3x. The IP address range of the Ericsson W3x subnet is displayed on the LAN page (see section 3.5). Wireless LAN Settings This section provides a general description of what is required to make your wireless clients work with the Ericsson W3x. Before you follow the instructions below, you need to configure the Wireless LAN settings in the Ericsson W3x as described in section 3.6 Wireless LAN. Prepare the Wireless Client(s) The coverage of the Wireless LAN depends on a number of factors, including the distance between the Ericsson W3x and the PC and the occurrence of obstacles, such as walls and electrical equipment. Guidelines on setting the hardware components of your wireless network are provided by your Wireless LAN interface provider. Install the Wireless LAN Interface Each PC on your Wireless LAN must be fitted with a Wireless LAN interface, such as a wireless network card. You also have to install the corresponding driver files for your particular Wireless LAN interface. The 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 6.2 6.2.1 6.2.2 70 PC Configuration 6.2.3 6.3 driver files and instructions on how to install them are provided together with the interface. Configure Access to the W3x WLAN The configuration steps below will vary depending on both the operating system and the Wireless LAN interface installed on the PC. These steps provide a basic outline. For specific instructions, refer to the documentation provided with your Wireless LAN interface. Configure the following wireless parameters on each of the wireless PCs:

Set the Wireless LAN interface to use infrastructure mode. This configures the PCs to access each other and the Internet through the Ericsson W3x. Configure the network name (SSID) and channel to match the network name and channel configured on the Ericsson W3x. This information can usually be obtained through WLAN scanning. The network name is case sensitive. If you are using Wired Equivalent Privacy (WEP) security, configure the same encryption key that is configured on the Ericsson W3x. If you are using Wi-Fi Protected Access (WPA or WPA2) security, configure the same passphrase that is configured on the Ericsson W3x. The passphrase is case sensitive. Configure the IP settings using the procedure described in section 6.1 IP Settings. USB Sharing Settings When a storage device or printer is connected to the USB port on the Ericsson W3x, information about the device is displayed on the Sharing page. To be able to use the shared device you also have to set up a connection to the shared device on your PC. In some cases, you have to make sure that your PC belongs to the same workgroup as the Ericsson W3x. Follow the instructions in the next section to check the workgroup on your PC. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 71 PC Configuration 6.3.1 6.3.1.1 Check Workgroup Settings The following sections include instructions on how to check the workgroup settings on a PC using Windows XP or 2000. Windows XP Follow the steps below to check the workgroup settings on a PC using Windows XP:

1. In the Windows task bar, click the Start button, and then click Control Panel. The Control Panel window is displayed. 2. If you are using Category View, click Performance and Maintenance and then See basic information about your computer. If you are using Classic View, double-click System. The System Properties window is displayed. 3. Click the Computer Name tab. 4. Click Change . The Computer Name Changes window is displayed. 5. Make sure that the Workgroup name is exactly the same as on the Sharing page. If not, you have to change the workgroup either on the PC or on the Ericsson W3x. 6. If you decide to change the workgroup on the PC, type the correct name in the Workgroup field and click OK . If you do not want to make any changes, click Cancel . The Computer Name Changes window is closed. 7. If you have changed the workgroup settings, follow the instructions on the screen to restart the PC. 6.3.1.2 Windows 2000 Follow the steps below to check the workgroup settings on a PC using Windows 2000:

1. In the Windows task bar, click the Start button, and then click Settings and Control Panel. The Control Panel window is displayed. 2. Double-click the System icon. The System Properties window is displayed. 3. On the Network Identification tab, click Properties . The Identification Changes window is displayed. 72 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 PC Configuration 6.3.2 4. Make sure that Workgroup is selected in the Member of section and that the name of the workgroup is exactly the same as the one on the Sharing page. If not, select the Workgroup option and type the name in the field. If there is already a workgroup name, although not the same as on the Ericsson W3x, you have to change it either on the PC or on the Ericsson W3x. 5. If you have made any changes, click OK . Otherwise, click Cancel . The Identification Changes window is closed. 6. If you have changed the workgroup settings, follow the instructions on the screen to restart the PC. Access a Shared Storage Device To access a USB storage device from a PC using Windows 2000 or XP, follow the steps below:

1. In the Windows task bar, click the Start button, and then click Run. 2. Type \\<host_name>\<share_name> in the Open field. The Host name and Share name are displayed on the Sharing page. Click OK . 3. The shared resource is displayed. Double-click on the shared file to open it. 6.3.3 Set Up a Connection to a Shared Storage Device The following sections include instructions on how to set up a connection to a mass storage device from a PC using Windows XP or 2000. The Storage device will be displayed in the My Computer window as a new partition. 6.3.3.1 Windows XP Follow the steps below to set up a connection to a shared storage device from a PC using Windows XP:

1. In the Windows task bar, click the Start button, and then click My Computer. The My Computer window is displayed. 2. From the Tools menu, select Map Network Drive. The My Network Drive window is displayed. 3. Select a drive that is not already used from the Drive drop-down menu. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 73 PC Configuration 6.3.3.2 4. In the Folder text field, type \\<host_name>\<share_name>. You find the host name and share name on the Ericsson W25 Sharing page. 5. Click Finish . The Map Network Drive window is closed. The device is displayed in the My Computer window as a new partition. Windows 2000 Follow the steps below to set up a connection to a shared storage device from a PC using Windows 2000:

1. Right-click the My Computer icon and select Map Network Drive... The Map Network Drive window is displayed. 2. Select a drive that is not already used from the Drive drop-down menu. 3. In the Folder text field, type \\<host_name>\<share_name>. You find the host name and share name on the Sharing page. 4. Click Finish . The Map Network Drive window is closed. The device is displayed in the My Computer window as a new partition. 6.3.4 Access a Shared Printer When a printer is connected to the USB port on the Ericsson W3x, information about the device is displayed on the Sharing page If you connect a USB printer directly to your PC, the printer device type and brand will normally be automatically detected and a printer driver assigned and installed. This is not the case when using a network shared USB printer connected to your Ericsson W3x. On the PCs that should use the printer, install the correct printer driver compatible with the PCs operating system. The printer driver is found either on the discs that were shipped with your printer or by downloading it from the manufacturers web page. The Ericsson W3x supports two protocols for printing: Samba and RAW. The protocol that is used may vary depending on printer and manufacturer. It also affects how to access the printer via the Ericsson W3x. The following sections include instructions on how to access a shared printer from a PC using Windows XP or 2000. 74 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 PC Configuration 6.3.4.1 Printer Supporting the Samba Protocol Follow the steps below to set up a connection to a shared printer from a PC using Windows XP (similar interface in Windows 2000):

1. Connect the printer to the USB port on the Ericsson W3x. 2. In the Windows task bar, click the Start button, and select Run. 3. Type \\<host_name> in the Open field and press Enter. The shared printer is displayed. 4. Right click on the printer and select Connect... 5. If you dont have the correct printer drivers installed a pop up window appears. Click OK to install the drivers. 6. Select a manufacturer and a printer in the Add Printer Wizard window or click Have disk . 7. Your computer now tries to connect to the shared printer. This could take a few minutes. 8. Print a test page to verify that your printer is connected properly. In the Windows task bar, click the Start button, and select Printers and Faxes. Your shared printer will be displayed as <printer name> on

<host_name>. Right-click on the printer icon and select Properties. On the General tab, click on Print Test Page . 6.3.4.2 Printer Supporting the RAW Protocol Follow the steps below to set up a connection to a shared printer from a PC using Windows XP (similar interface in Windows 2000):

1. Connect the printer to the USB port on the Ericsson W3x. 2. In the Windows task bar, click the Start button and select Settings followed by Printers and Faxes. A new window appears including printers connected to the PC. 3. Select Add a printer. The Add Printer Wizard appears. Click Next>

to proceed. 4. In the Local or Network Printer window, select Local printer attached to this computer and click Next> . 5. In the Select a Printer Port window, check Create a new port and from the Type of port drop-down list select Standard TCP/IP Port. Click Next> . 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 75 PC Configuration 6. The Add Standard TCP/IP Printer Port Wizard opens. Click Next> to proceed. 7. In the Add Port window and Printer Name or IP Address field enter the IP address of the Ericsson W3x (preconfigured 192.168.1.1) and a Port Name, for example IP_192.168.1.1. Click Next> . 8. In the Additional Port Information Required window, select the Custom checkbox and click the Settings button. 9. In the Configure Standard TCP/IP Port Monitor window, select Raw as Protocol and type 9100 as Port Number below Raw Settings. 10. Click OK to return to the wizard and click Next> to proceed. 11. In the Completing the Add Standard TCP/IP Printer Port Wizard window, verify your settings and click Finish . 12. The Add Printer Wizard Install Printer Software window is displayed. Select the Manufacturer and Printer and click Next> . 13. Enter a name for your printer and click Next> . 14. Select Do not share this printer option and click Next> . 15. Print a test page to verify that your printer setup is working properly and then click Next> to proceed. It could take a minute or two for the test page to be printed. 16. Click Finish in the Add Printer Wizard. 17. Repeat these steps if you have further computers which should have access to the shared printer. 76 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Troubleshooting 7 Troubleshooting 7.1 7.2 This chapter describes how to solve a number of issues that could occur during installation, configuration, and use of the Ericsson W3x. More information is available at www.ericsson.com/fwt. If none of the suggested methods in this chapter solve your problem, you are recommended to:

1. Restart the Ericsson W3x (see section 6.1). 2. Reset the Ericsson W3x to factory default configuration (see section 6.2). 3. Contact your service provider. Restart To restart the Ericsson W3x, click Restart on the System web page. If you cannot access the WUI, remove the power cable to disconnect the Ericsson W3x from power and wait a moment before reconnecting the cable. Reset to Factory Default Settings The factory default configuration contains the original settings of your Ericsson W3x. To reset the configuration to factory default settings, click the Reset button in the FACTORY RESET section on the System web page. If you cannot access the WUI, the following procedure resets all configurable values back to factory default settings:

1. Press the Reset button with the tip of a pen. The Standby button starts blinking. 2. Wait until the Standby button stops blinking which indicates that the reset is finished. Note: A reset to factory default configuration cannot be undone. If you reset the Ericsson W3x to default configuration, all your previous 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 77 Troubleshooting configuration changes are replaced. If you have previously changed the password, the Enter password page will be displayed. You have to login to the web pages with the default password (user). 7.3 LAN Connections Table 25 LAN Connections Indication/Symptom Cannot access the local network from a PC that is connected to one of the Ethernet ports on the Ericsson W3x. Cannot access the WUI on the Ericsson W3x. What to do Check the network cable and make sure that there is a physical connection between the PC and the Ericsson W3x and that at least one of the corresponding LAN connector indicators is lit. If not, make sure that the cable is properly connected or try with another Ethernet cable. Check that the PC is configured to obtain IP address automatically using DHCP. If not, change the PC TCP/IP settings. For instructions, see section 6.1.1 Obtaining IP Settings Automatically or refer to the manual of your operating system. Make sure you are using the correct LAN IP address in the web browser. If the LAN IP address has been changed and you do not know the current IP address, use the Reset button to reset the Ericsson W3x to factory default configuration

(see section 7.2). This will set the LAN IP address to 192.168.1.1 and the web page address to http://192.168.1.1. Make sure you are using the correct login password. If the default password has been changed and you do not know the current password, use the Reset button to reset the Ericsson W3x to 78 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Troubleshooting Indication/Symptom What to do factory default configuration (see section 7.2). This will reset the login details to default values (User name user and Password user). 7.4 Internet Access Table 26 Internet access Indication/Symptom Cannot access the Internet from any of my local devices. The Internet connection is unacceptable slow or regularly dropping. Cannot access a certain Internet application or specific type of data What to do Check the status of the Alarm indicator. If it is blinking, see the information in the Alarms section on the Overview page. On the Internet page, verify that the Link status is Up and that an IP address is defined. Check the signal quality indicator on the front of the Ericsson W3x. The more segments displayed in the bar graph, the stronger the signal. Try to move the Ericsson W3x to another position or attach an external antenna (indoor window or outdoor roof mounted). External antennas are available as accessories to the Ericsson W3x. For optimizing the performance of the Internet connection, it might be necessary to change some TCP settings in the client PC as described in section 7.4.1 Change TCP Settings. Check the NAT page to make sure that the ALG supporting the 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 79 Troubleshooting Indication/Symptom applications. What to do Internet application is enabled. If the application requires UPnP IDG, check that UPnP IDG is enabled on the NAT page. A port forwarding rule might be required for a specific application. See section 3.7.3 Port Forwarding. 7.4.1 Change TCP Settings To achieve maximum performance on the Internet connection some parameters in the TCP/IP stack of the client PC can be changed. These kinds of settings are hidden in the Windows registry, but there are some tools that give user friendly access to them, for example TCP Optimizer, http://www.speedguide.net/downloads.php The following TCP settings are recommended to optimize the performance:

TCP Receive Window = 146000 Selective ACK:s = Yes Max Duplicate ACK:s = 2 RFC1323 TCP Window Scaling = Yes (enabled) Note: Windows Vista and recent versions of Linux kernels have automatic window scaling enabled by default and should not need any TCP tweaking. 7.5 Wireless LAN Connection Table 27 Wireless LAN Indication/Symptom Cannot access the local network from a wireless device. What to do indicator Check that the WLAN on the front panel of the Ericsson W3x is on. If not, connect an Ethernet cable between the PC and the Ericsson W3x to establish a connection and enable the wireless LAN (disabled in the default configuration). 80 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Troubleshooting Indication/Symptom What to do Verify that the Wireless LAN interface installed on the wireless client is active. Keep the Ericsson W3x away from electrical devices that disturb the radio signals, for example microwave ovens. Try to move the Ericsson W3x to another location, but make sure that the mobile network signal is still acceptable before finalizing the installation. Make sure that your Ericsson W3x network does not use the same radio channel as other wireless devices, for example security systems. The radio channel is displayed on the Wireless LAN page. To avoid interference, let the Ericsson W3x select a channel automatically (Auto). Verify that the network name

(SSID) on the Ericsson W3x and the wireless client are the same. Note that the network name is case- sensitive. Verify that the operating system and Wireless LAN interface of the client supports the authentication and encryption method (WEP-64, WEP-128, WPA, or WPA2) configured on the Ericsson W3x. These settings are displayed on the Wireless LAN web page. If the security method is not supported in the client, configure the Ericsson W3x to use another method. For the configured security method, make sure that the same encryption key or passphrase is configured on both the Ericsson W3x and the client. Note that a passphrase is case sensitive. If whitelist is enabled, verify that the 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 81 Troubleshooting Indication/Symptom What to do wireless client is included on this list. If the wireless client uses a static IP address, make sure that this IP address is on the same subnet as the Ericsson W3x. The IP address and subnet mask for the Ericsson W3x is displayed on the LAN page. 7.6 Access to Shared Files or Printer If you cannot access a shared storage device or printer connected to the USB connector on the Ericsson W3x, take the following action to identify and solve the problem:

Check that the USB device is detected by the system by looking on the Event Log web page. Connect the USB device, wait a few seconds and click the Refresh button. Make sure the Display list box is set to All. Move to the bottom of the log using the scroll bar on the right. If your USB device is recognized you will se some lines like the example below:

Jan 1 00:07:29 FWT user.info kernel: usb 1-3: new high speed USB device using ehci_hcd and address 4 Jan 1 00:07:29 FWT user.info kernel: scsi0 : SCSI emulation for USB Mass Storage devices Jan 1 00:07:34 FWT user.notice kernel: Vendor:

Model: USB DISK Pro Rev: PMAP Jan 1 00:07:34 FWT user.notice kernel: Type: Direct-Access ANSI SCSI revision: 00 Jan 1 00:07:35 FWT user.notice kernel: SCSI device sda: 4013056 512-byte hdwr sectors (2055 MB) Jan 1 00:07:35 FWT user.notice kernel: sda: assuming Write Enabled Jan 1 00:07:35 FWT user.err kernel: sda: assuming drive cache:

write through Jan 1 00:07:35 FWT user.notice kernel: SCSI device sda: 4013056 512-byte hdwr sectors (2055 MB) Jan 1 00:07:35 FWT user.notice kernel: sda: assuming Write Enabled Jan 1 00:07:35 FWT user.err kernel: sda: assuming drive cache:

write through Jan 1 00:07:35 FWT user.info kernel: sda1 Jan 1 00:07:35 FWT user.notice kernel: Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0 Restart the Ericsson W3x. Disconnect the USB device from the Ericsson W3x, and then reconnect it. 82 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Troubleshooting Make sure that the PC belongs to the same workgroup as the Ericsson W3x. For instructions, see section 6.3.1 Check Workgroup Settings. The Ericsson W3x workgroup is displayed on the Sharing web page. If you have problems accessing a printer, make sure that the printer drivers are correctly installed on the PC. 7.7 Telephony and Fax Service (W35 only) Note: The telephony and the fax services will work without any further configurations but must be supported by the subscription/network in order to work. If you are unsure, check with your service provider. Table 28 Telephony and Fax Service Indication/Symptom Cannot make or receive a call from a telephone connected to the Ericsson W35. What to do Make sure that the phone is working, for example by connecting it to a fixed line telephone network

(PSTN). The phone has to be of a standard touch tone type (with DTMF keypad support). Note: Some old phones have a keypad, although they do not support DTMF. These phones are consequently not supported by the Ericsson W35. The phone must be connected to the Phone connector on the Ericsson W35. Verify that a dial tone is heard when picking up the handset. If not, replace the handset and restart the Ericsson W35. Allow some two minutes for the startup and then listen for the information tone again If an information tone other than the dial tone is heard when lifting the handset verify that the SIM card is correctly inserted, re-enter the PIN, or enter the PUK and a new PIN to unlock the SIM card. The method to use depends on the type of 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 83 Troubleshooting Indication/Symptom Cannot send or receive on a fax connected to the Ericsson W35 What to do information tone. For information about tones, see section 4.2 Information Tones. Make sure that the fax is connected to the Phone/Fax connector on the Ericsson W35. Check that the Internet LED is on and on the LAN page that the Ericsson W35 has received an IP address. The data service is a prerequisite for the fax service, see section 7.4 Internet Access for troubleshooting the data service. Make sure that the fax is working, for example by connecting it to a fixed line telephone network

(PSTN). Messages regarding fax status and failures are shown on the fax. 84 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Glossary Glossary 802.11b An IEEE standard for a wireless network that operates at 2.4 GHz with rates up to 11 Mbps. 802.11g An IEEE standard for a wireless network that operates at 2.4 GHz with rates up to 54 Mbps. 2G Second Generation The second generation wireless communications technology, introducing digital voice encoding. Low speed data services are supported. 3G Third Generation The third generation wireless communications technology. 3G includes enhanced voice, data, and video capabilities, improved availability, broad bandwidth and high speed. ALG Application Layer Gateway An ALG provides a translation and transportation service for an Internet application. AES Advanced Encryption Standard An encryption method used by WPA2. AES offers a high level of security and is approved for sensitive corporate and government data transmission. AP Access Point An Internet device that seamlessly connects wired and wireless networks. Access points attached to a wired network support the creation of multiple radio cells that enable roaming throughout a facility. APN Access Point Name A reference to the Internet access point of an Service provider. Association Describes the establishment and maintenance of a wireless link between devices. (If security is enabled, the devices cannot do anything but exchange security credentials with this link). See Authentication. Authentication The processthat occurs after association to verify the identity of the wireless device or end user and allow access to the network. Broadcasting To simultaneously send the same message to multiple recipients. CDMA Code Division Multiple Access A general term describing mobile air interface technologies based on spread spectrum digital radio access methods, offering benefits including increased capacity, quality and security. CDMA is fundamental to 3G mobile systems. Channel A channel determines the radio frequency used by an access point to pass data traffic to wireless clients. Available channels depend on region specific regulations. CHAP Challenge-Hanshake Authentication Protocol CHAP is an authentication scheme used by PPP servers to validate the identity of remote clients. CHAP periodically verifies the identity of the client by using a three-way handshake. This happens at the time of establishing the initial link, and may happen again any time afterward. The verification is based on a shared secret (such as the client users password). See also PAP. CIFS Common Internet File System See SMB. CLIP Calling Line Identity Presentation A service that provides a called party the 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 85 Glossary calling line identity,for example the phone number, of the caller. DHCP Dynamic Host Configuration Protocol A protocol used by networked computers

(clients) to obtain IP addresses and other parameters such as the default gateway, subnet mask, and IP addresses of DNS servers from a DHCP server. DHCP server A configuration server, capable of configuring network devices with a variety of information, such as IP addresses, required for their operation. DNS Domain Name System (or Service) The distributed name/address mechanism used in the Internet. It comprises distributed online databases that contain mappings between human-readable names and IP addresses, and servers, which provide translation services to client applications. DTMF Dual Tone Multi Frequency The telephone signaling method used over the line in the voice-frequency band to the call switching center. The version of DTMF used for telephone tone dialing is known by the trademarked term Touch-Tone. EDGE Enhanced Data rates for Global Evolution A technology that gives GSM the capacity to handle services for the third generation of mobile telephony. EDGE provides three times the data capacity of GPRS. Encryption Encryption is an effective way to achieve data security by translating data into a secret code. Encryption key A sequence of characters used for data encryption. The encrypted data can only be sent and received by users with access to the encryption key. Ethernet The most common LAN technology, used in wired networks. FTP File Transfer Protocol A protocol for exchanging files over the Internet. FTP is most commonly used to download and upload files from and to servers. Gateway A network point that acts as an entrance to another network. GPRS General Packet Radio Service A packet-based mobile communications system building on GSM. Advantages over standard GSM include higher data transmission speeds, more efficient use of radio resources and continuous connection to the network to facilitate more advanced non-

voice services. GSM Global System for Mobile Communication The second generation mobile system originally developed in Europe. GSM is oriented to voice and circuit mode data. Host A device (usually a computer) that is connected to a TCP/IP network, including the Internet. Each host has a unique IP address. Host name The DNS name of a device on a network, used to simplify the process of locating computers on a network. HSPA High Speed Packet Access A mobile broadband technology that improves the performance of networks based on the Universal Mobile Telecommunications System (UMTS). IGD Internet Gateway Device See UPnP IGD. IEEE Institute of Electrical and 86 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Glossary Electronics Engineers IEEE (pronounced I-tripleE) is an organization composed of engineers, scientists, and students. The IEEE is best known for developing standards for the computer and electronics industry. In particular, the IEEE 802 standards for local area networks are widely followed. IMEI International Mobile Equipment Identity The IMEI number is a 15 digit numnber which includes information on the origin, model, and serial number unique to every mobile device. The IMEI number is used by the mobile network to identify valid devices. IP Internet Protocol A part of a suite of protocols that effectively defines the Internet as we know it. Specifies addressing and control information for routing data packets over networks. IP address The address of a host on the Internet, consisting of four numbers, each from 0 to 255, separated by periods, for example 192.168.1.1. An IP address consists of a network ID that identifies the particular network the host belongs to, and a host ID uniquely identifying the host itself on that network. A network mask is used to define the network ID and the host ID. See also Private IP Address and Public IP Address. LAN Local Area Network A computer network limited to the immediate area, such as a home, office, or small building. Lease time The amount of time that a dynamically assigned IP address will be valid for a specific device. MAC address Media Access Control address The permanent hardware address of a device assigned by its manufacturer. MAC addresses are expressed as six pairs of hexadecimal characters (0-9 and a-f), with each pair separated by colons. For example:

1a:2b:23:5b:66:9a Mass Storage Various techniques and devices used to store large amounts of data. An example of a mass storage device is a hard disk. MBR Mobile Broadband Router A router providing residential and small office users with broadband services like high-

speed data, voice, and fax connectivity. Internet access is provided through the mobile communications network. NAT Network Address Translation A service performed by many routers that translates a networks IP address into a private IP address for each device on the LAN. Only the router and the LAN know these addresses; the outside world sees only the public IP address when talking to a computer on the LAN. Network mask A sequence of bits applied to an IP address to select the network ID while ignoring the host ID. Bits set to 1 mean select this bit while bits set to 0 mean ignore this bit. For example, if the network mask 255.255.255.0 is applied to the IP address 100.10.50.1, the network ID is 100.10.50, and the host ID is 1. See also Subnet mask. Packet The units of data transmitted on a network. Each packet contains a payload (the data), plus overhead information such as where it came from (source address) and where it will go (destination address). PAP Password Authentication Protocol PAP is a simple authentication protocol used to authenticate a user to a remote access server or Internet Service Provider (ISP). PAP 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 87 Glossary is used by PPP and almost all network operating system remote servers support PAP. PAP transmits unencrypted ASCII passwords over the network and is therefore considered insecure, it is used as a last resort when the remote access server does not support a stronger authentication protocol, such as CHAP. Passphrase A secret password used for WPA and WPA2 wireless data encryption. The encryption is based on a WPA master key that is derived from the passphrase and the network name

(SSID). PC Personal Computer A computer designed for use by one person at a time. Port In TCP and UDP networks, an endpoint to a logical connection. The port number identifies what type of port it is. For example, port 80 is used for HTTP traffic. PIN Personal Identification Number A secret code used for individual access to for example computer networks. Generally, a PIN is made up of 4 to 10 digits. PPP Point-to-Point Protocol A protocol for serial data transmission that is used to carry IP (and other protocol) data between the service provider and your computer. Private IP Address A private IP Address is typically assigned to a client on a LAN and is not used outside the LAN. Private IP addresses are typically used when multiple computers share the same Internet connection. Protocol A set of rules governing the transmission of data. In order for a data transmission to work, both ends of the connection have to follow the rules of the protocol. PSTN Public Switched Telephone Network The traditional, wired telephone network designed primarily for voice traffic. Public IP Address A public IP address is a globally unique number that identifies a device on the Internet. Anyone on the Internet can connect to the device using the public address. PUK Personal Unblocking Key A secret code made up of 8 to 10 digits. The PUK is used to reactivate a SIM card that has been blocked. Roaming The movement between microcells in a radio network. Roaming service is used to provide network access independent of where the user resides and what service provider that is running the network. Routing The forwarding of data between a local network and the Internet on the most efficient route, based on the datas destination IP address and current network conditions. A device that performs routing is called a router. RSSI Received Signal Strength Indicator The RSSI is an indicator of the strength of the received radio signal. SIM Subscriber Identity Module The smart card required by all mobile customers to operate their phones. Carries authentication, billing and information about the individual subscriber, as well as address book and other personalized information. SMB Server Message Block An application-level network protocol mainly applied to shared access to files, printers, serial ports, and miscellaneous communications between nodes on a network. SMB was later renamed to CIFS

(Common Internet File System) with more 88 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Glossary features added, including support for symbolic links, hard links, and larger file sizes. TFTP Trivial File Transfer Protocol A TCP/IP protocol commonly used for software downloads. SSID Service Set Identifier A unique network name, or identifier, that differentiates one wireless LAN from another. All access points and clients attempting to connect to a specific WLAN must use the same SSID. Subnet A portion of a network. The subnet is distinguished from the larger network by a subnet mask that selects some of the computers of the network and excludes all others. The subnets devices remain physically connected to the rest of the network, but they are treated as though they were on a separate network. Subnet mask A mask that defines a subnet. See also Network mask. Switching Routing data traffic by setting up temporary connections between two or more network points. This will take the data toward its intended destination. TCP Transmission Control Protocol See TCP/IP. TCP/IP Transmission Control Protocol /

Internet Protocol The basic protocols used on the Internet. TCP is responsible for dividing data up into packets for delivery and reassembling them at the destination. IP is responsible for delivering the packets from source to destination. When TCP and IP are bundled with higher-level applications such as HTTP, FTP, Telnet, and so on, TCP/IP refers to this whole suite of protocols. TKIP Temporal Key Integrity Protocol A protocol used for WPA data encryption. It ensures that a unique master key is generated for each packet, supports message integrity and sequencing rules, and supports re-keying mechanisms. TKIP avoids the problems of WEP static keys by dynamically changing data encryption keys. UDP User Datagram Protocol A connection-less transport service that dispenses with the reliability services provided by TCP. UDP gives applications a direct interface with IP and the ability to address a particular application process running on a host via a port number, without setting up a connection session. UPnP Universal Plug and Play A networking architecture that provides compatibility among networking equipment, software, or between equipment and software. UPnP IGD UPnP Internet Gateway Device A standard used by UPnP aware clients, such as MSN Messenger, to work properly from behind a NAT. UMTS Universal Mobile Telecommunications Service A 3G wireless system that delivers high-

bandwidth data and voice services to mobile users. UMTS has an air interface based on WCDMA and a core network based on the General Packet Radio Service (GPRS). URL Uniform Resource Locator The address of a resource on the Internet, for example www.ericsson.com. USB Universal Serial Bus An interface for connecting peripherals such as storage devices and printers to a host. 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 89 Glossary WAN Wide Area Network A network of computers that covers a large geographical distance. With respect to the Ericsson W25, WAN refers to the Internet. WUI Web User Interface In Ericsson W25 the WUI refers to a built-in web based configuration tool with wizard support. WCDMA Wideband CDMA The radio access technology for wideband wireless access supporting 3G services. It allows very high speed multimedia services like wireless Internet access and videoconferencing. WCDMA is also known as CDMA DS (Direct Sequence). WEP Wired Equivalent Privacy A method for data encryption on wireless networks. Data is encrypted into blocks of either 64 bits length or 128 bits length. The encrypted data can only be sent and received by users with access to a private encryption key. Wireless A common term used to describe telecommunications in which radio waves

(rather than some form of wire) carry the signal over part or all of the communication path. WLAN Wireless Local Area Network A WLAN is a network in which a mobile user can connect to a LAN through a wireless

(radio) connection. The IEEE 802.11 standard specifies the technologies for Wireless LANs. WPA Wi-Fi Protected Access An authentication and encryption standard for wireless networks. WPA addresses the security limitations of WEP, providing a stronger data encryption method; TKIP. WPA data encryption is based on a WPA master key. The master key is derived from the passphrase and the network name (SSID) of the device. WPA2 Wi-Fi Protected Access 2. An enhanced version of WPA. For data encryption, WPA2 uses AES instead of TKIP. 90 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12 Ericsson Enterprise AB www.ericsson.com Ericsson AB 2008 - All Rights Reserved 1/1551-CRH 102 168 Uen Rev PA2 2008-11-12