FCC ID: RAR80005000 802.11n dual-band WIFI router

BelAir20EO and AP 511x Series Quick Install Guide QUICK GUIDE 1/006 92-LZA 101 803 Uen D Copyright Ericsson AB 2013. All rights reserved. No part of this document may be reproduced in any form without the written permission of the copyright owner. Disclaimer The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. Ericsson shall have no liability for any error or damage of any kind resulting from the use of this document. Trademark List Wi-Fi Wi-Fi is a registered trademark of the Wi-Fi Alliance. Wi-Fi Certified Logo Ericsson The Wi-Fi CERTIFIED logo is a registered trademark of the Wi-Fi Alliance. Ericsson is the trademark or registered trademark of Telefonaktiebolaget LM Ericsson. All other product or service names mentioned in this manual are trademarks of their respective companies. 1/006 92-LZA 101 803 Uen D | 2013-12-13 Getting Started 1 1.1 Getting Started Package Contents External antennas are ordered and shipped separately. For AP 5115 to AP 5118:

Customers supply their own power cable and use the power cable connector kit to terminate the cable. Units can be powered either by AC power or by Power over Ethernet (PoE). 1/006 92-LZA 101 803 Uen D | 2013-12-13 2 BelAir20EO and AP 511x Series Quick Install Guide 1.2 AC Power (AP 5115 to AP 5118 Only) These units accept AC input power in the range of 100240 V AC. The units do not have a power switch. They are powered on when connected to a power source. Maximum AC power consumption is 14.5 W. Warning!

The unit contains a 5-A fuse and relies on the rated fuse or circuit breaker of the wall outlet (15 A in North America, 10 A in Europe). Warning!

Use ONLY the Ericsson power cable connector supplied with the unit. Use of any other power cable connector can damage the unit and voids the Ericsson product warranty. 1.3 Internet Port and Power The unit can be powered with IEEE 802.3af or IEEE 802.3at Power over Ethernet (PoE). Use IEEE 802.3af PoE for most applications. IEEE 802.3af PoE supplies a maximum of 12.95 W to the powered device. Table 1 PoE Power Consumption Table State Idle Medium Traffic High Traffic Max. Traffic PoE Port Only 3.6 W 8.4 W 10.8 W 11.76 W PoE Port and One LAN Port 4.05 W 8.85 W 11.25 W 12.21 W The PoE switch or power injector must meet local and national regulatory requirements. 802.3at Power Source Equipment (PSE) Specification:

50.0 to 57 V DC, with 30 W output power from the PSE 3 1/006 92-LZA 101 803 Uen D | 2013-12-13 Getting Started 802.3at Powered Device (PD) Specification:

42.5 to 57 V DC at the PD, with 25.5 W maximum input power to the PD 802.3at Cable Specification:

100 m maximum length

Maximum cable pair resistance of 12.5 Ohms, satisfied by using CAT5 or CAT5e as specified by ANSI/TIA/EIA-568 or Class D as specified by ISO/IEC 11801:1995

600 mA maximum current per pair 1.4 Functional Earth Ground and Lightning Protection Units are not designed to survive a direct lightning hit. However, they are intended to withstand the voltage and current surges induced from nearby lightning activity. The level of required lightning protection depends on regional lightning conditions and location of installation. For example, an AP installed on a roof top requires greater lightning protection than an AP installed on the side of a building. The following is a list of recommended installation practices to mitigate the voltage and current surges induced from lightning activity. If there is a conflict between these recommendations and local or national electrical codes, the local or national electrical codes must be followed.

For streetlight or hydro/telecom pole mounting the AC power adapter should be protected with a lightning surge protector. AC power routed to the power adapter must be routed inside the pole. If power is routed on the pole exterior, the power must be routed through a metal conduit grounded at the base of the pole. For rooftop installations, the unit must not be mounted at the highest point on the building. If the building has installed lightning arrestors, the unit must be located within the umbrella protection zonea 60 degree zone under the lighting arrestor, but if possible, the unit should not be located closer than 30 feet (approx. 10 m) from the lightning arrestor. Power and Ethernet cables must be routed through independent grounded metal conduits. For lightning surge protection, the installer must connect a separate ground wire between the external chassis of the unit and a ground on the pole. The ground point on the AP accepts a 1/4 screw. It is recommended for areas susceptible to lightning activity, such as on poles, rooftops, or on or near any tall structures, that shielded CAT 5e or CAT 6 Ethernet cable be employed. The external antennas ports of the unit require lightning arrestors to be employed whenever the external antenna is located more than 3 feet 1/006 92-LZA 101 803 Uen D | 2013-12-13 4 BelAir20EO and AP 511x Series Quick Install Guide

(approx. 1 m) from the unit. When lightning arrestors are used, they must be located within 3 feet (approx. 1 m) of the unit and must be grounded to both the unit and protective earth ground. The 1/4 GND screw of the unit can be used for this application. 5 1/006 92-LZA 101 803 Uen D | 2013-12-13 Installing the BelAir20EO and AP 511x Series AP 2 Installing the BelAir20EO and AP 511x Series AP 2.1 Step 1Select Location Choose a proper place for the unit. In general, the best location is at the center of the intended wireless coverage area, within line of sight of all wireless devices. For optimum performance, consider these guidelines:

Mount the unit as high as possible above any obstructions in the coverage area.

Avoid mounting next to or near building support columns or other obstructions that can cause reduced signal or null zones in parts of the coverage area.

Mount away from any signal absorbing or reflecting structures (such as those containing metal). The unit can be mounted on any wall or on a pole. Warning!

Do not install the unit in any areas where blasting (blasting caps, radio controlled equipment) or explosive gases can be present. Warning!

To comply with FCC radio frequency (RF) exposure limits (FCC OET 65C) for the general population, antennas must be located a minimum distance of 12 inches (approx. 30 cm) or more from the body of all persons. 1/006 92-LZA 101 803 Uen D | 2013-12-13 6 BelAir20EO and AP 511x Series Quick Install Guide 2.2 Step 2Mount Unit Wall or Large Pole Mounting Large poles have an outer diameter greater than 3 inches (7.6 cms). If mounted on a flat surface, the unit must be mounted to a surface that is at least 1/2-inch plywood or its equivalent. Poles must have the equivalent rigidity. 1. Attach the mounting plate to the wall or pole.

For walls, use up to four 1/4 inch (M6) anchoring bolts. Use the plate as a drill hole template. The outer edges of the plate must be elevated from the wall surface while the center channel must touch the wall surface. For large poles, use through bolts or use the pairs of slots for stainless steel strapping. The center channel must touch the pole surface. 2. Connect ground wire to unit. 7 1/006 92-LZA 101 803 Uen D | 2013-12-13 Installing the BelAir20EO and AP 511x Series AP 3. Attach four mounting screws to unit back. Note: Ground wire not shown. 4. Attach unit to mounting plate:

a Insert mounting screws on the back of the unit into shoulder screw holes on mounting plate. Slide unit down until screws are into the slots. Tighten screws snug. b Screw in the remaining mounting screw at base of unit into the mounting plate hole. 1/006 92-LZA 101 803 Uen D | 2013-12-13 8 BelAir20EO and AP 511x Series Quick Install Guide Note: Ground wire not shown. Small Pole Mounting Small poles have an outer diameter less than 3 inches (7.6 cms). 1. Connect ground wire to unit. 2. Use two stainless steel straps to secure unit to pole. 9 1/006 92-LZA 101 803 Uen D | 2013-12-13 Installing the BelAir20EO and AP 511x Series AP Note: Ground wire not shown. Strap mounting applies to all units except the AP 5115 to AP 5118. 2.3 Step 3Mount and Attach External Antennas This step applies only to the following APs:

Table 2 APs and Required Antennas APs BelAir20EO-11C, BelAir20EO-11CR2, AP 5117R, AP 5117U BelAir20EO-11D, BelAir20EO-11DR2, AP 5118R, AP 5118U AP 5113 Required Antennas Two 5 GHz External 11.5 dBi Two 2.4 GHz External 8 dBi One 2.4 GHz External 12 dBi Ericsson Description and Part Number 5 GHz 11.5 dBi Dual Feed Directional Antenna

(BNCKH0091 or INE 105 2162) 2.4 GHz 8 dBi Dual Feed Directional Antenna

(BNCKH0007 or INE 105 2159) Dual Polarization 2.42.5 GHz Flat Panel Antenna 12 dBi (KRE 105 217) Mounting Kit (KRY 901 293) The external antennas must be approved by Ericsson specifically for the APs. The antennas are ordered and shipped separately. 1. Attach the 5 GHz or 2.4 GHz antennas to their mounting surface. Ericsson provides several different types of 5 GHz and 2.4 GHz antennas, each with its own requirements and procedures for attaching to a mounting surface. For details on attaching the antennas to their mounting surface, 1/006 92-LZA 101 803 Uen D | 2013-12-13 10 BelAir20EO and AP 511x Series Quick Install Guide refer to the mounting procedures supplied with the antennas that were ordered. 2. Connect external 5 GHz or 2.4 GHz antennas to connectors. See the figure. Connect only antennas that are approved specifically for the units. Either antenna can connect to either connector. Use thread-locker and self-amalgamating tape to keep connection tight and waterproof.

Connect external 5 GHz or 2.4 GHz antennas here. Connect only antennas that are approved specifically for the units. Either antenna can connect to either connector. Use thread-locker and self-amalgamating tape to keep connection tight and waterproof. Note: Ground wire and mounting hardware not shown. 2.4 Step 4Prepare Power Cable (AP 5115 to AP 5118 Only) Refer to Figure 1. 11 1/006 92-LZA 101 803 Uen D | 2013-12-13 Installing the BelAir20EO and AP 511x Series AP Figure 1 Power Cable Connector Assembly 1. Place compression nut (4), grommet (3), and body (2) over power cable as shown in Figure 1. 2. Strip outer jacket and inner conductors as shown in Figure 1. 3. Secure conductors to appropriate terminals by tightening screws on insert assembly (1). Refer to the following table. Conductor Type Ground Power Neutral North American Color Green/Yellow Black White European Color Terminal ID Green/Yellow Brown Blue 1 2 3 4. Attach body (2) to insert assembly (1) by rotating black knurled ring on insert assembly in a clockwise direction. 5. Secure compression nut (4) to body (2) by rotating in a clockwise direction. 1/006 92-LZA 101 803 Uen D | 2013-12-13 12 BelAir20EO and AP 511x Series Quick Install Guide 2.5 Step 5Connect and Power On BelAir20EO and All AP 511x Series: Power over Ethernet The AP gets its operating power from the PoE port when connected to a device that provides IEEE 802.3af or 802.3at compliant Power over Ethernet (PoE). Figure 2 Power Connection for BelAir20EO and All AP 511x Series Power over Ethernet Note: Ground wire and mounting hardware not shown. Warning!

The BelAir20EO and AP 511x series AP must be connected to a power source that complies to IEEE 802.3af or 802.3at. Caution!

The PoE connection to the BelAir20EO and AP 511x series AP must use the supplied Ethernet gland to ensure a waterproof connection. Failure to use the Ethernet gland voids the Ericsson product warranty. AP 5115 to AP 5118 Only The AP can get its operating power directly from an AC power source or from the Internet port when connected to a device that provides IEEE 802.3af or 802.3at compliant Power over Ethernet (PoE). If the AP is connected to both a PoE source device and an AC power source, the AP automatically adjusts to use the most suitable power source. 13 1/006 92-LZA 101 803 Uen D | 2013-12-13 Installing the BelAir20EO and AP 511x Series AP Figure 3 Power Connections for AP 5115 to AP 5118 Note: Ground wire and mounting hardware not shown. 2.6 Step 6Check Indicators After powering on, wait 2 minutes and check the indicators on the unit. If the indicators are not as shown, refer to the BelAir20EO and AP 511x Series Technical Description, 1/1550-LZA 101 803. 2.7 Step 7Configure Unit In most cases, the unit configures itself automatically after powering on. To configure the unit manually through its local web interface or Command Line Interface (CLI), refer to the Access Point User Guide, 1/1553-LZA 101 806. 1/006 92-LZA 101 803 Uen D | 2013-12-13 14 BelAir20EO and AP 511x Series Quick Install Guide Ericsson AB 2013. All rights reserved. No part of this document may be reproduced in any form without the written permission of the copyright owner. The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. Ericsson shall have no liability for any error or damage of any kind resulting from the use of this document. 1/006 92-LZA 101 803 Uen D BelAir20EO and AP 511x Series Conformity and Regulatory Statements STATEMENT OF COMPLIANCE 1/174 02-LZA 101 803 Uen C Copyright Ericsson AB 2013. All rights reserved. No part of this document may be reproduced in any form without the written permission of the copyright owner. Disclaimer The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. Ericsson shall have no liability for any error or damage of any kind resulting from the use of this document. Trademark List Wi-Fi Wi-Fi is a registered trademark of the Wi-Fi Alliance. Wi-Fi Certified Logo Ericsson The Wi-Fi CERTIFIED logo is a registered trademark of the Wi-Fi Alliance. Ericsson is the trademark or registered trademark of Telefonaktiebolaget LM Ericsson. All other product or service names mentioned in this manual are trademarks of their respective companies. 1/174 02-LZA 101 803 Uen C | 2013-12-13 Contents Contents 1 1.1 1.2 1.3 2 3 3.1 4 5 6 7 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 About this Document Scope Target Group Comments About the Documentation Regulatory Information and Disclaimers Manufacturers US Federal Communication Commission Conformity Statement FCC Interference Statement Manufacturers Industry Canada Conformity Statement Manufacturers European Community Conformity Statement Declaration of Conformity for RF Exposure Product Disposal Mise au rebut du produit Produktentsorgung Verwijdering van het product Tuotteen hvittminen Smaltimento del prodotto Produktbortskaffelse Eliminao do produto Eliminacin del producto 1 1 1 1 2 3 3 5 9 12 13 13 13 13 14 14 14 14 14 1/174 02-LZA 101 803 Uen C | 2013-12-13 BelAir20EO and AP 511x Series Conformity and Regulatory Statements 1/174 02-LZA 101 803 Uen C | 2013-12-13 About this Document 1 About this Document This section describes the scope and target groups for this document. 1.1 Scope This document provides the regulatory information, disclaimers, and compliance statements for the product. 1.2 Target Group The information in this document is intended for all personnel who want to learn more about the product. 1.3 Comments About the Documentation Ericsson encourages you to provide feedback, comments or suggestions so that we can improve the documentation to better meet your needs. With your comments provide the following:

Document title Document number and revision Page number or section number Please send your comments to your local Ericsson Support. 1/174 02-LZA 101 803 Uen C | 2013-12-13 1 BelAir20EO and AP 511x Series Conformity and Regulatory Statements 2 Regulatory Information and Disclaimers Installation and use of this device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications to this product not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. The manufacturer is not responsible for any interference to radio or television equipment caused by unauthorized modification of this device, or attachment of any antennas or equipment other than those specified by the manufacturer. The manufacturer or its authorized resellers or distributors will assume no liability for any damage arising from failure to comply with these guidelines, or failure to comply with local, regional or national safety, electrical or building codes, or government regulations. This product is manufactured in China with originating and non-originating product. Ce produit est fabriqu en Chine avec des matires originaires et non originaires du produit. 2 1/174 02-LZA 101 803 Uen C | 2013-12-13 Manufacturers US Federal Communication Commission Conformity Statement 3 Manufacturers US Federal Communication Commission Conformity Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 3.1 FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for assistance. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:

FCC Radiation Exposure Statement:

1/174 02-LZA 101 803 Uen C | 2013-12-13 3 BelAir20EO and AP 511x Series Conformity and Regulatory Statements This device complies with FCC RF radiation exposure limits for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 12 inches (30 cm) between the radiator and your body. This transmitter must not be colocated or operating in conjunction with any other antenna or transmitter. Note: The country code selection is for non-US model only and is not available to all US models. Per FCC regulation, all Wi-Fi products marketed in US must be fixed to US operation channels only. 4 1/174 02-LZA 101 803 Uen C | 2013-12-13 Manufacturers Industry Canada Conformity Statement 4 Manufacturers Industry Canada Conformity Statement This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 30 cm between the radiator and a human body. Caution:

This device has been designed to operate with an antenna having a maximum gain of 12 dB. Antennas having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. Table 1 BelAir20EO and AP 511x series Antennas Type Internal omnidire ctional antenna Internal omnidire ctional antenna Internal direction al antenna Internal direction al antenna Internal direction al antenna External direction al antenna External direction al antenna Gain 4.4 dBi 6.7 dBi 8 dBi Brand Ericsson Manufacturer Ericsson Ericsson Ericsson Ericsson Ericsson 11.5 dBi Ericsson Ericsson 12 dBi 8 dBi Ericsson Ericsson Ericsson Ericsson 11.5 dBi Ericsson Ericsson Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent 1/174 02-LZA 101 803 Uen C | 2013-12-13 5 BelAir20EO and AP 511x Series Conformity and Regulatory Statements isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types listed above with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Professional installation instruction Please be advised that due to the unique function supplied by this product, the device is intended for use with our software and licensed third-party only. The product will be distributed through controlled distribution channel and installed by trained professional and will not be sold directly to the general public through retail store. 1 2 Installation personnel: This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge. The general user shall not attempt to install or change the setting. Installation location: The product shall be installed at a location where the radiating antenna can be kept 30 cm from nearby person in normal operation condition to meet regulatory RF exposure requirement. 3 External antenna: Use only the antennas which have been approved by the applicant. The non-approved antenna(s) may produce unwanted spurious or excessive RF transmitting power which may lead to the violation of FCC/IC limit and is prohibited. 4 Installation procedure: Refer to the BelAir20EO and AP 511x Series Quick Install Guide, 1/006 92-LZA 101 803 for details. 5 Warning: Please carefully select the installation location and make sure that the final output power does not exceed the limit set force in relevant rules. The violation of the rule could lead to serious federal penalty. Ce dispositif est conforme la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. NOTE IMPORTANTE:

Dclaration d'exposition aux radiations:

Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 30 cm de distance entre la source de rayonnement et dun corps humain. 6 1/174 02-LZA 101 803 Uen C | 2013-12-13 Manufacturers Industry Canada Conformity Statement Avertissement:

Ce dispositif a t conu pour fonctionner avec une antenne ayant un gain maximal de 12 dB. Une antenne gain plus lev est strictement interdite par les rglements d'Industrie Canada. L'impdance d'antenne requise est de 50 ohms. Table 2 Antennes pour BelAir20EO and AP 511x series Type Antenne omnidire ctionnelle interne Internal omni directionnelle antenna Antenne directionnelle interne Antenne directionnelle interne Antenne directionnelle interne Antenne directionnelle externe Antenne directionnelle externe Gain 4.4 dBi 6.7 dBi Marque Ericsson Fabricant Ericsson Ericsson Ericsson 8 dBi Ericsson Ericsson 11.5 dBi Ericsson Ericsson 12 dBi Ericsson Ericsson 8 dBi Ericsson Ericsson 11.5 dBi Ericsson Ericsson Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radio-lectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. Le prsent metteur radio a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessus et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Instructions d'installation professionnelle 1/174 02-LZA 101 803 Uen C | 2013-12-13 7 BelAir20EO and AP 511x Series Conformity and Regulatory Statements Veuillez noter que l'appareil tant ddi une fonction unique, il doit tre utilis avec notre logiciel. Ce produit sera propos par un rseau de distribution control et install par des professionnels; il ne sera pas propos au grand public par le rseau de la grande distribution. 1 Installation: Ce produit est destin un usage spcifique et doit tre install par un personnel qualifi maitrisant les radiofrquences et les rgles s'y rapportant. L'installation et les rglages ne doivent pas tre modifis par l'utilisateur final. 2 Emplacement d'installation: En usage normal, afin de respecter les exigences rglementaires concernant l'exposition aux radiofrquences, ce produit doit tre install de faon respecter une distance de 30 cm entre l'antenne mettrice et les personnes. 3 Antenne externe: Utiliser uniquement les antennes approuves par le fabricant. L'utilisation d'autres antennes peut conduire un niveau de rayonnement essentiel ou non essentiel dpassant les niveaux limites dfinis par FCC/IC, ce qui est interdit. 4 Procdure d'installation: Consulter le manuel dinstallation rapide. 5 Avertissement: Choisir avec soin le lieu d'installation et s'assurer que la puissance de sortie ne dpasse pas les limites en vigueur. La violation de cette rgle peut conduire de srieuses pnalits fdrales. 8 1/174 02-LZA 101 803 Uen C | 2013-12-13 Manufacturers European Community Conformity Statement 5 Manufacturers European Community Conformity Statement Table 3 European Community Conformity Statement Language English Deutsch Dansk Espaol Franais slenska Italiano Nederlands Norsk Portugus Suomalainen Svenska Statement This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Dieses Gert entspricht den grundlegenden Anforderungen und den weiteren entsprecheneden Vorgaben der Richtlinie 1999/5/EU. Dette udstyr er i overensstemmelse med de vsentlige krav og andre relevante bestemmelser i Directiv 1999/5/EF. Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directiva 1999/5/EC. Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la Directive 1999/5/EC. essi bnaur samrmist lgbonum krfum og rum kvum tilskipunar 1999/5/ESB. Questo apparato conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva 1999/5/EC. Deze apparatuur voldoet aan de belangrijkste eisen en andere voorzieningen van richtlijn 1999/5/EC. Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU-directiv 1999/5/EC. Este equipamento satisfaz os requisitos essenciais e outras provises da Directiva 1999/5/EC. Tm laite tytt direktiivin 1999/5/EY oleelliset vaatimukset ja on siin asetettujen muidenkin ehtojen mukainen. Denna utrustning r i verensstmmelse med de vsentliga kraven och andra relevanta bestmmelser i Direktiv 1999/5/EC. The Declaration of Conformity related to this product can be found by contacting Ericsson. The BelAir20EO and AP 511x series AP complies with the following EU Radio standards:

1/174 02-LZA 101 803 Uen C | 2013-12-13 9 BelAir20EO and AP 511x Series Conformity and Regulatory Statements

EN 300 328 V1.4.1 (2003-04) and EN300 328-2 V1.2.1 (2001-12) Electromagnetic compatibility and Radio spectrum Matters (ERM);

Wideband Transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive. EN 300 440-2 V1.1.1 (2001-09) Electromagnetic compatibility and Radio spectrum Matters (ERM); Short range devices; Radio equipment to be used in the 1 GHz to 40 GHz frequency range; Part 2: Harmonized EN under article 3.2 of the R&TTE Directive. EN 300 440-2 V1.1.2 (2004-07) Electromagnetic Compatibility and Radio spectrum Matters (ERM); Short range devices; Radio equipment to be used in the 1GHz to 40 GHz frequency range; Part 2: Harmonized EN under article 3.2 of the R&TTE Directive. EN 301 893 V1.4.1 (2007-07) Broadband Radio Access Networks (BRAN);

5 GHz high performance RLAN; Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive EN 300 328 V1.6.1 (2004-11) Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive. UK Interface Requirement 2005 UK Radio Interface Requirement for Wideband Transmission Systems operating in the 2.4 GHz ISM Band and Using Wide Band Modulation Techniques (November 2006). UK Interface Requirement 2006 Wireless Access Systems (WAS) including RLANs operating in the 5150-5725 MHz band (Version 3.0) 98/34/EC Notification number: 2006/421/UK Published 14 November 2006 UK Interface Requirement 2007 Fixed Broadband Services operating in the 5725 -5850 MHz band (Version 3.0) 98/34/EC Notification Number:

2006/422/UK Published 30 May 2007 The BelAir20EO and AP 511x series AP complies with the following EU EMC standards:

EN 301 489-17 V1.2.1 (2002-08) ElectroMagnetic Compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) Standard for Radio Equipment and Services; Part 17: Specific Conditions for 2.4 GHz Wideband Transmission Systems and 5 GHz High Performance RLAN Equipment The BelAir20EO and AP 511x series AP complies with the following EU Safety standards:

EN 60825-2:2000 Safety of Optical Fibre Communication Systems 10 1/174 02-LZA 101 803 Uen C | 2013-12-13 Manufacturers European Community Conformity Statement

EN 60950:2000 Safety of Information Technology Equipment IEC 60950:2005 Second Edition and/or EN 60950-1:2006 The following CE mark is affixed to the BelAir20EO and AP 511x series AP:

Note: This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation for example in France the frequencies 2454-2483.5 MHz are restricted to 10 mW effective isotropic radiated power (EIRP) in outdoor environments, so channels 8-13 require reduced power. For more details, contact Ericsson. 1/174 02-LZA 101 803 Uen C | 2013-12-13 11 BelAir20EO and AP 511x Series Conformity and Regulatory Statements 6 Declaration of Conformity for RF Exposure This Wireless LAN radio device has been evaluated under FCC Bulletin OET 65C, Health Canada Safety Code 6 and EN 62311:2008, and found to be compliant to the requirements set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247 (b) (4) addressing RF exposure from radio frequency devices. This Wireless LAN radio device also conforms to EU Health and Safety Directive 2004/40/EC as per EN 50385. This device complies with FCC RF radiation exposure limits for an uncontrolled environment. The radiated output power of this Wireless LAN device is below the FCC radio frequency exposure limits. However, this device should still be installed and used in such a manner that the potential for human contact during normal operation is minimized. Warning!

In order to comply with RF exposure limits established in the ANSI C95.1 standard, this equipment should be installed and operated at a minimum distance of 12 inches (30 cm) between the radiator and a human body. This transmitter must not be colocated or operating in conjunction with any other antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. 12 1/174 02-LZA 101 803 Uen C | 2013-12-13 Product Disposal 7 Product Disposal Ericsson adheres to directive 2002/96/EC of the European Parliament and the council of 27 January 2003 on Waste Electrical and Electronic Equipment

(WEEE). To dispose of equipment, including batteries, contact Ericsson customer service to get a Return Material Authorization (RMA) number and shipping instructions. 7.1 Mise au rebut du produit Ericsson se conforme la directive 2002/96/EC du Parlement europen et du Conseil de lEurope du 27 janvier 2003 relative la destruction des dchets dquipements lectriques et lectroniques (DEEE). Si vous souhaitez vous dbarrasser de lquipement, y compris des piles, veuillez communiquer avec le service la clientle de Ericsson, afin dobtenir un numro dautorisation de retour du matriel et des instructions sur les modalits dexpdition. 7.2 Produktentsorgung Ericsson erfllt die Anforderungen der Richtlinie 2002/96/EG des Europischen Parlaments und des Rates vom 27. Januar ber Elektro- und Elektronik-Altgerte (Waste Electrical and Electronic Equipment = WEEE). Fr die Entsorgung von Gerten, einschlielich Batterien, wenden Sie sich bitte an den Kundendienst von Ericsson, um eine RMA-Nummer

(Rcksendenummer) und die Versandanweisungen zu erhalten. 7.3 Verwijdering van het product Ericsson volgt Richtlijn 2002/96/EG van het Europese Parlement en de Raad van 27 januari 2003 betreffende afgedankte elektrische en elektronische apparatuur (AEEA). Voor het verwijderen van apparatuur, met inbegrip van batterijen, neemt u contact op met Ericsson klantenservice voor een retournummer (RMA) en verzendinstructies. 1/174 02-LZA 101 803 Uen C | 2013-12-13 13 BelAir20EO and AP 511x Series Conformity and Regulatory Statements 7.4 Tuotteen hvittminen Ericsson noudattaa shk- ja elektroniikkalaiteromusta 27 pivn tammikuuta 2003 annettua Euroopan parlamentin ja neuvoston direktiivi 2002/96/EY. Palauttaaksesi vlineet, mukaan luettuina akut, ota yhteys Ericsson asiakaspalveluun, niin saat RMA (Return Material Authorization) numeron ja lhetysohjeet. 7.5 Smaltimento del prodotto Ericsson aderisce alla direttiva 2002/96/CE del parlamento Europeo e del Consiglio dEuropa del 27 gennaio 2003, sullo smaltimento degli apparecchi elettrici ed elettronici (WEEE). Per lo smaltimento di tali apparecchi, comprese le batterie, contattare lassistenza clienti di Ericsson per ottenere un numero di autorizzazione alla restituzione del materiale da smaltire (Return Material Authorization - RMA) e le istruzioni per la spedizione. 7.6 Produktbortskaffelse Ericsson overholder direktivet 2002/96/EC fra Europa-Parlamentet og -Rdet dateret den 27. januar 2003 om Waste Electrical and Electronic Equipment

(WEEE) (Affald af elektrisk og elektronisk udstyr). For at bortskaffe udstyr, samt batterier, kontakt kundeservicen hos Ericsson for at f et Return Material Authorization (RMA)-nummer

(returneringstilladelsesnummer) og forsendelsesinstruktioner. 7.7 Eliminao do produto A Ericsson cumpre a Directiva 2002/96/CE do Parlamento Europeu e do Conselho, de 27 de Janeiro de 2003, relativa aos Resduos de Equipamentos Elctricos e Electrnicos (REEE). Para proceder eliminao do equipamento, incluindo as baterias, favor contactar a assistncia ao cliente da Ericsson para obter um nmero de Autorizao de Devoluo do Material (RMA Return Material Authorization) e as instrues relativas ao envio. 7.8 Eliminacin del producto Ericsson cumple con la directiva 2002/96/EC del Parlamento Europeo y del Consejo de 27 de enero de 2003 sobre los residuos de aparatos elctricos y electrnicos (RAEE). 14 1/174 02-LZA 101 803 Uen C | 2013-12-13 Product Disposal Para la eliminacin de equipo, incluyendo las pilas, contacte con el servicio de atencin al cliente de Ericsson y obtenga el nmero de una Autorizacin de Devolucin de Material (RMA) y las instrucciones para la expedicin. 1/174 02-LZA 101 803 Uen C | 2013-12-13 15