1.SCOPE This document is intented to assist related parties with the integration of MIOPS-BTM into their host devices. 2. OPERATIONAL DESCRIPTION & BLOCK DIAGRAM MIOPS BTM devices are designed to meet the needs of OEMs adding robust Bluetooth connectivity within these products. 1) DC 1.8~3.6V Power supply 2) Minimal System U1, Control the work of the various parts of machine, with external crystal, includes 16MHz as base clock 3) J1 is General-Purpose I/O Pins 4) Antenna: Antenna 5) Frequency Range: 2.4GHz 3. SPECIFICATIONS CATEGORIESFEATUREIMPLEMENTATIONBluetoothV4.0 Dual ModeFrequency2.402-2.480 GHzRange50 metersSupply VoltageSupply1.8-3.6VAntenna OptionInternalMultilayer chip antennaPhysicalDimensions15 x 21 x 1 mmEnvironmentalOperating-25C to +75CMiscellaneousWarranty1 YearApprovalsFCC/CEMIOPS-BTMWireless Specification 4. PIN DEFINITIONS
#
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Pin Name GND SWD Pin Function GND Digital I/O Description Ground System reset (active low). Also hardware debug and flash programming I/O. SWC MP21 MP22 MP23 MP24 MP25 MP26 MP27 MP28 MP29 VDD GND MP30 MP0 MP1 MP2 MP3 MP4 General Purpose I/O General Purpose I/O General Purpose I/O General Purpose I/O General Purpose I/O General Purpose I/O General Purpose I/O Digital Input Hardware debug and flash programming I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Analog Input Digital I/O Analog Input Digital I/O Digital I/O Power GND Digital I/O Digital I/O Analog Input Digital I/O Analog Input Digital I/O Analog Input Digital I/O Analog Input Digital I/O Analog Input General Purpose I/O General Purpose I/O Power Supply Ground General Purpose I/O General Purpose I/O General Purpose I/O General Purpose I/O General Purpose I/O General Purpose I/O 139238337436535634733832931103011291228132714151617181920212223242526 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 MP5 MP6 MP7 MP8 MP9 VDD GND MP10 MP11 MP12 MP13 MP14 MP15 MP16 MP17 MP18 MP19 MP20 GND Digital I/O Analog Input Digital I/O Analog Input Digital I/O Digital I/O Digital I/O Power GND Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O GND General Purpose I/O General Purpose I/O General Purpose I/O General Purpose I/O General Purpose I/O Power Supply Ground General Purpose I/O General Purpose I/O General Purpose I/O General Purpose I/O General Purpose I/O General Purpose I/O General Purpose I/O General Purpose I/O General Purpose I/O General Purpose I/O General Purpose I/O Ground Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). End Product Labeling This transmitter module is authorized only for use in devices where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in visible area with the following: Contains FCC ID: 2AD8MMBTM37 End Product Manual Information The user manual for end users must include the following information in a prominent location IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be colocated or operating in conjunction with any other antenna or transmitter. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or colocation with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC authorization. This device is intended only for OEM integrators under the following conditions: The antenna must be installed such that 20 cm is maintained between the antenna and users. As long as a condition above is met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed
(for example, digital device emissions, PC peripheral requirements, etc.).