FCC ID: 2ATRJRAD Radio communication bridge for ticketless reception solution

CONDITIONS OF SITES LAY OUT Even if we use authorized radio channels, ESII certified equipments, we draw your attention on internal or external causes in your premises that can induce a lessening of the functional behavior of our systems of reception supervising, and in which ESII shall not be held responsible of, especially on the following points:

Interferences due to external causes, sporadically or permanently. Topography and structure of your premises (contact us). Non respect of ESIIs instructions.

RESTRICTIONS OF USE The radio reach depends essentially on Master/Slave distance and depends on the environment. Generally, a limitation of 25m in direct vision of the Master/Slave distance allows to be protected against the major part of radio reach problems. And a minimum of 5m between 2 devices set on a different frequency. It is very important to be sure that radio waves are going through the minimum quantity of elements (partition, furniture, etc.) which reduce considerably the communication reach. Also check the nature of the walls (avoid concrete, metal parts, etc.) The positioning of the modules is decisive. It is important to free the radio modules from all interference sources (central processing unit, display, metal parts, etc.). For optimum communication, the environment of the radio modules must be free from all objects around 30cm at least. The modules must not be installed inside consoles or metal housings, etc. COMMUNICATION RECOVERY In case of fault communication, check the following points:

Check that all equipments are correctly supplied and wired. After having checked the correct starting of the system, check that all status visual indicators of the radio link indicate a perfect communication (the red visual indicator, beside the antenna, must be lit without blinking and permanently). If one of the status visual indicators is off or blinks:

First, check detailed points described in the previous chapters: distances, heights, clearing of modules, etc. Test the radio module showing communication failures by positioning it close to the Master to check its correct behavior. Change the radio module showing communication failures by a new one. In case of serious radio reach, a good solution is to place the Master module at the center of the room or site to reduce distances at their lowest value. Issue ITXT90 Ind.I Tous droits rserv All rights reserved. 2020 ESII VIDEO RJ45 "SLAVE"

RJ45 "SLAVE"

LIGHT PROCESSING EQUIPMENT 230VAC-15VDC 15W E V A L S HUB RADIO

R E T S A M

5 4 J R D E S U T O N

. X A M M 5 2

E V A L S

5 4 J R D E S U T O N R E T S A M X . 5 M M A 2 HUB RADIO RJ45 "MASTER"

RECEPTION SUPERVISOR SYSTEM

(eGestat, Pilote, etc.) 2 5 M M A X. AUTOMATIC TICKET DISPENSER RJ45 "SLAVE"

RJ45 "SLAVE"

HUB RADIO E V A L S

R E T S A M

5 4 J R D E S U T O N CONSOLE 230VAC-15VDC 15W DISPLAYS RJ45 "SLAVE"

5 4 J R 230VAC-15VDC 15W E V A L S HUB RADIO

R E T S A M

5 4 J R D E S U T O N RADIO RELAY MODULE RADMO10(WRL102) EN ESII reports the RADMO10 complies with guidelines 2014/30/EU (CEM), 2014/35/EU (low voltage), 2014/53/UE (RED), EN 301-489-3 (CEM), EN 301-489-1 (CEM), EN 300 220-2

(RADIO), CEI 62311 (EMF), CEI 62368-1 (Electrical Safety), 2011/65/UE (ROHS) and 2012/19/UE (DEEE) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with part 15 of the FCC Rules and with Industry Canada licence-

exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. NOTE: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the users authority to operate the equipment ELEMENTARY CARES WARNINGS No part can be repaired by the user. In case of failure, please contact the maintenance service of the company ESII. Do not put the apparatus on an unstable or hot element. Do not open the housing for another reason than setting (only a qualified individual can perform this operation). ANTENNA ORIENTATION To orientate the antenna :

1. Loosen the connectors nut (A). 2. Orientate the antenna (B). 3. Tighten the connectors nut. CONNECTORS AND VISUAL INDICATORS Fixing the HUB RADIO must be done with the 2 adhesives supplied with the product. 1. Body 2. Fixing hole 3. Housing closing screws 4. Antenna 5. Double-sided adhesive location FIXING WIRING When the power supply cable is plugged into its connector (1), the module automatically sets itself in Slave mode. If not so, it is set in Master mode. ON A MASTER MODULE The RJ45 connector MASTER just beside the antenna is connected to the reception supervisor, and those beside the supply connector must not be connected. ON A SLAVE MODULE The two RJ45 connectors DEVICES beside the supply connector are connected to the peripherals. The RJ45 connector beside the antenna must not be connected. HOUSING OPENING CONNECTORS 1. Supply connector 2. Peripheral #1 connector (Slave) 3. Peripheral #2 connector (Slave) 4. Reception supervising connector (Master) VISUAL INDICATORS 5. Green visual indicator: Tx Transmission of information to the ESII network. 6. Green visual indicator: Rx Reception of information from the ESII network. 7. Yellow visual indicator: Settings indicator At the starting of the module, it indicates during few seconds that the module is supplied. Then, this indicator gives the settings:

Lit: channel #1. Blinking: channel #2. 8. Red visual indicator: Processing indicator A the starting of the module, it indicates during few seconds the protocol status:

Lit: EBUS protocol. Off: reception protocol. Then, this indicator gives the communication quality status:

Lit: =100% (normal use). Blinking: <100% (use limit reached). Off: <75% (no or bad radio link). CONFIGURATION To set the HUB RADIO, you must position the switchs SW1 et SW3 : Channel OFF et ON : Channel 1 : 869,5 MHz Europe ON et ON : Channel 2 : 869,9 MHz Europe ON et OFF : Channel 4 : 920,3 MHz USA/Canada OFF et OFF : Channel 5 : 924,3 MHz Reserved SW2. Protocol ON : EBUS (eSirius, eGestat, eTurn). OFF : PACC (Sirius, Gestat). SW4. Positionned sur OFF CARACTERISTICS Dimensions :

Height :

(MASTER):

(POWER):

Electricals caracteristics 24V

(direct current) Electricals caracteristics 8 - 24V

(direct current) 2Amax Operating Temperature max :

35C 100x60x25mm 82g The MEAN WELL ES18E24-P1J with the device CTIPV3 power supply provided by ESII must be used to power the RADMO10 on the MASTER port. Use only a certified power supply certified and classified PS2 according to the IEC62368-1:2014 (limited to 2A max in normal and fault conditions).. OTHER 9. Adjustable antenna Issue ITXT90 Ind.I Tous droits rserv All rights reserved. 2020 ESII C R A C K !

B A 3 2 1 9 4 5 6 7 8

Federal Communications Commission Authorization and Evaluation Division Subject: Confidentiality Request regarding application for certification of FCC Laverune, Thursday 17 January 2020 ID: 2ATRJRAD Applicant: ESII Product: RADMO10 To Whom It May Concern:

Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type Block Diagram Schematics Operational Description Parts List File Name RADMO10 BlkDia.pdf RADMO10 Schem.pdf RADMO10 Opdes.pdf RADMO10 PartsLst.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. If you have any queries, please do not hesitate to contact us. Regards, David GELLY, 17 january 2020 Adresse du sige : ESII ZI Sud 2 rue de la Prade 34880 LAVRUNE Adresse postale : ESII ZI Sud Lavrune 34433 St Jean de Vedas Cedex France Tl. : +33 (0)4 67 07 04 70 Fax : +33 (0)4 67 07 04 77 Internet : www.esii.com Email : info@esii.com S.A.S. au capital de 527 448,60 - SIRET 343 616 751 000 32 N Identification FR 31 343 616 751 RC Montpellier B 343 616 751 NAF 3320C

Laverune, 17 january 2020 Subject: RADIO Certification of RADMO10 Applicant: ESII Product: RADMO10 FCC ID: 2ATRJRAD IC ID: 25190-RAD To Whom It May Concern:

We would like to submit the above product for Certification concerning FCC and Canadian rules. Please review all required documents enclosed. This is a ticketless reception solution. It displays dynamically the number of people waiting and when the counter calls, it starts vibrating, buzzing and displaying the point of service to go to. Compliance for RF exposure requirement was demonstrated in this test report. If you have any queries, please do not hesitate to contact us. Regards, David GELLY, 17 january 2020 Adresse du sige : ESII ZI Sud 2 rue de la Prade 34880 LAVRUNE Adresse postale : ESII ZI Sud Lavrune 34433 St Jean de Vedas Cedex France Tl. : +33 (0)4 67 07 04 70 Fax : +33 (0)4 67 07 04 77 Internet : www.esii.com Email : info@esii.com S.A.S. au capital de 527 448,60 - SIRET 343 616 751 000 32 N Identification FR 31 343 616 751 RC Montpellier B 343 616 751 NAF 3320C

On our behalf, | appoint M.

, to act as our agent in the preparation of this application for equipment certification. | certify that submitted documents properly describe the device or system for which equipment certification is sought. | also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commissions regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on ou behalf, | acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Aa) (oe) e (Son Adresse du sige : ESII Z] Sud 2 rue de la Prade 34880 LAVERUNE Adresse postale : ESI] ZI Sud Lavrune 34433 St Jean de Vedas Cedex France Tl. : +33 (0)4 67 07 04 70 Fax : +33 (0)4 67 07 04 77 Internet : www.esii.com Email : info@esii.com S.A.S. au capital de 527 448,60 - SIRET 343 616 751 000 32 N Identification FR 31 343 616 751 RC Montpellier B 343 616 751 NAF 3320 Olivier HEYER from Emitech Montpellier 145 rue du Massacan 34741 VENDARGUES CEDEX FRANCE TIMCO Engineering Inc. 849 N.W. State Road 45 P.O. Box 370 Newberry, Florida 32669 This authorization is valid until further written notice fro prade 34880 LAVERUNE FRANCE David GELLY, Project 271 January 2020