User Guide MODELS: INEBOX001 INTRODUCTION The manufacturer suggests reading this manual carefully. This equipment is manufactured with first quality material by experienced technicians. Proper installation and maintenance will guarantee a reliable service for years to come. A Qrcode fixed to the front or back side of the box specifies the model number, serial number, Voltage and Amperage. Drawings and extra parts numbers are included in this manual. The electrical diagram is at the end of the user guide. ATTENTION Inesocompany is not responsible for damages to the property or the equipment caused by personnel who is not certified by known organizations. The customer is responsible for finding qualified technicians in electricity and plumbing for the installation of the box. Security of the workers Thefirstobjectiveistoprotectthepersonalthatwillbeinchargeofthereplacementofthelight sources.Thatreplacementwillbedoneoncewehaveswitchedofthedistrict(orthegeneral circuitbreaker)ofthelinethatdeliverthemaintotheroadwherewewillapplythepilot. Thatforitisimportanttohaveagoodlocalizationofthatbreakerandmaketesttobesurewe haveopenedthegoodbreakerbeforewestartanyprocessontheexistinginstallation. Theproceduretoguarantythatthecircuitisopenistovalidatewithsomeoneinchargeofthe operationonsitetocontrolifthesupplyisstillhereornotwhenweopenthebreaker.Oncethat isvalidatedwehavetoguarantythatnoonecanclosethebreakeragain,thatcanbedonewitha keylockerwhenthebreakerisopen. CONSTRUCTION You just bought the most advanced lighting control box, "Inesocompany" technology at its best. This box is manufactured using the highest quality components and material. The box is one of the key elements of the network, that for it is important to pay a special attention during the installation process to guaranty a long and reliable system. SHIPPING For your safety, this equipment has been verified by qualified technicians and carefully crafted before shipment. The freight company assumes full responsibility concerning the delivery in good condition of the equipment in accepting to transport it. IMPORTANT FOR THE RECEPTION OF THE MERCHANDISE Take care to verify that the received equipment is not damaged before signing the delivery receipt. If damage or a lost part is noticed, write it clearly on the receipt. If it is noticed after the carrier has left, contact immediately the freight company in order that they do their inspection. We do not assume the responsibility for damages or losses that may occur during transportation. Safety and security IMPORTANT SAFETY INFORMATION CAUTION: As when installing or using any high voltage electrical equipment, basic safety precautions should always be followed. Under no circumstances should you attempt to clean, install, inspect, repair, disassemble or otherwise service this product without first shutting off all power to the unit. SERIOUS BODILY INJURY OR DEATH COULD OCCUR IF YOU IGNORE THIS WARNING. THIS PRODUCT MUST BE INSTALLED BY A CERTIFIED & QUALIFIED ELECTRICAL ENGINEER IN ACCORDANCE WITH ALL NATIONAL, STATE, PROVINCIAL AND LOCAL ELECTRICAL CODES AND PERMITS. Before proceeding with installation or service maintenance of this product:
Review the entire Installation Instructions Procedure thoroughly and completely prior to installation & use. Inspect this properly packaged product for any damage that may have occurred during transit. Verify the availability of necessary tools and incidental material. Verify applicable code requirements. Field assembly and installation are subject to acceptance by local inspection authority. Appropriate safety equipment to be determined by end user, per applicable safety standards and precautions. FAILURE TO DO SO COULD CAUSE DAMAGES OR SERIOUS INJURY OR DEATH & VOID YOUR WARRANTY. In no way is this document intended to construe warranty or fitness of use of the products described, nor is it intended to provide safety instruction for those installing the product. It is the responsibility of the installer to respect the installation procedure and to use the box for what it has been designed for (lighting) with a maximum allowed current. The environment is also an important point that has to be strictly respected. The product is and IP 55 product. This is not design for all the external use. It is not vandal proof for example. Make sure you respect the specification before installing the box in any application. This document should be given to the owner after installation and should be retained for future reference. 1/ InesoBox Overview 5:Dimming0V 6:OutputDimming110V20mA 7:CTNTemperatureSensor 8 :CTNTemperatureSensor 2/ Electrical Specification A/InputPowerSupply Voltage Frequency Current B/OutputPowerSupply Voltage Frequency Current C/DigitalandAnalogueI/O 1:AccessoriesPowerSupply(CarRadar,PedestrianRadar) 2:AccessoriesDigitalI/O 3:AccessoriesDigitalI/O 4:AccessoriesPowerSupplyReference 5:DriversDimmingReference 6:DriversDimmingSignal 7:CTNTemperatureSensor 8:CTNTemperatureSensor 100277Vac 5060Hz 10A 100277Vac 5060Hz 10A 12Vdc200mA 3.3Vdc20mA 3.3Vdc20mA 0Vdc 0Vdc 110Vdc20mA 2.5Vdc1mA 2.5Vdc1mA 3/ Radio Specifications RF Radio Communications Maximum output radio power 0dbm (1mw) Receiver category 2 Channels Data rate RF connector 915Mhz Transmitter duty cycle 1%
1 32.768Kb/s +/- 1%
SMA NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is Increase the separation between the equipment and receiver. connected. Consult the dealer or an experienced radio/TV technician for help. Radiofrequency radiation exposure Information:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 50 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FCCID : 2AAOFINEBOX001 NOTICE:
This device complies with Part 15 of the FCC Rules and with Industry Canada licence-
exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTICE:
Changes or modifications made to this equipment not expressly approved by Inesocompany may void the FCC authorization to operate this equipment. 4/ Wiring and External Protection OvercurrentprotectionisnotprovidedbyInesoBoxitMUSTbedonebythecustomer. Characteristics&featuresimbeddedinthebox Non-Start Detection Error Reporting Light Power Monitoring Tracks Burn-In Hours Dimming Based on Schedule or pre programmed scenario Photocell Adapter (Detection) Operating Temp Range Storage Temp Range Humidity Yes Yes Yes Yes Yes Optional
-20 to 70C
-40 to 85C Unlimited except above 40C less than 90%
Rain tight (mounted below) IP55 127 x 85 x 30 mm IR resistant plastic 100V ~ 277V AC 50Hz & 60Hz 0.25W 30-400W 10 A at 230V AC 1 - 10V 1.5 mm Water Degree of protection Dimensions Casing Input Voltage Range Frequency Minimum Power Consumption Ballast Wattage Range Maximum current allowed for non inductive loads Driver control Electric connections 5/ Installation procedure 1ststep. Connect the main input (live and neutral) from the driver to the left cable of the inesobox. Once you have done the connection, please make sure the connection have been well done by pulling (not to strongly but enough to verify ~0.5kg) each wiretoguarantyasafeandreliableconnection. 2ndstep Connectthedimmercabletothedimminginputofthedriver.Youhavetotakecare onthepolarityofthecables.Theredlineisthepositiveandthegrayisthenegative line for the dimming function. If you make a wrong connection it can damage the driverandthebox.Sobeforepoweringthelightfixturepayaspecialattentiononthe polarityofthedimmingcontrol. 3rdstep In case of a LED fixture it would be used, it is highly recommended to install a temperaturesensorononeoftheledpanelinordertomonitorandtocontrolthe temperatureoftheLEDsources.Thisfeaturewillallowguarantyingabetterchance toreachthemaxlifetimeoftheleds.Incaseyoudontconnectthesensoryoucant provetoyouLEDsupplierthatyouhaverespectedthetemperaturerange. 4thstep Drillaholeinthelightfixturecovertoallowtheantennatogoout.Usethesilicon partsthatwerecommendtoguarantyasafeandsecurefixingoftheantennaontop ofthelightpole.Pleaseusethedeliveredantenna. 5th Connectthegroundwiresofthedriverandthegroundofthemaininputtogetheron thededicatedscrewlocatedinthelightpole.Incaseoftherewouldnotbeoneuse thequickconnectthatwerecommendtoconnectallthegroundlinestogether. 6th Connectthemainwiresofthebox,onceyouinstallthelightheadonthetopofthe lightpole. Make all the connections of the wiring coming from the light pole and the lamp. Please refer to the detail A & B for the connections. Make sure that the cables are well connected and ensure by pulling on each of them before closing all. For more security we suggest that you protect the connections with insulation tape. Nota: Please read the special instruction about the remote antenna at the end of the installationchapter. Generalviewofatypicalwiring MainfortheDriver 2ndstepconnecttheDrivercontrolsignal
(110V)tothededicateddimminginput. Pleaseusetherecommendedquick connects. 3thstepconnecttheCTN
(temperaturesensor)totheLED pannel.Maxlenghtofthecable3m Pleaseusetherecommendedquick connects. 1ststepconnecttheliveand neutraltothedriver Pleaseusethe recommendedquick connects. 5thConnect alltheground linestogether onthe dedicated screworuse thequick connect Fuse board 6th Connectthemaininputoftheinesoboxtothe fuseboard.Pleasemakesuretheconnectionsare welldonethanreconnectthefuse. Mainfromthestreet Remote antenna installation procedure and warning. The remote antenna is used in case of we need to go out from a thick metal housing. That for we propose 2 references of coaxial cable with at the end a connection for the antenna that will be placed outside the metal housing. In case of you would like to do your own, we do not assume the responsibility for damages or non function that would occur after. So please take a special attention of the installation procedure. The performances of the whole system will be affected in case of non respect to those instructions. NOTICE:
Changes or modifications made to this equipment not expressly approved by Inesocompany may void the FCC authorization to operate this equipment. 6/ Description of the different information displayed by the LED Led RED Fixed ON : mean that the relay is ON, the dimming output is > 0v as result the LIGHT is ON Fixed OFF : mean that the relay is Off, the dimming output = 0v, as result the LIGHT is OFF Fast Blinking : device going back to factory state Slow Blinking : device error so please refer to the error procedure Led GREEN Fast Blinking: calibration of bulb in progress Slow Blinking: 250ms/2s device is linked with a concentrator (this is the normal status) Very Slow Blinking: 250ms/5s: device is not linked (status that can appear during installation procedure) LEDs PushButton 7/ Behavior change due to pushing the button Push-Button:
Short press : toggling ON/OFF (when toggling ON, the box restore the dimming value saved on the last off) Long Press (>1s) : toggling dimming. Increase or Decrease Very long press (>10s) : return to factory state