FCC ID: 2BDCA-PG-025 Soundbar

143X210MM) 2.0CH SOUNDBAR PG-025 User Manual Rear Panel 14V 1G-32G 1 2 3 4 5 Top Panel ARC ARC USB USB AUX AUX OPTICAL OPTICAL DC IN DC IN ARC ARC USB USB AUX AUX OPTICAL OPTICAL DC IN DC IN 5 4 3 2 1

+ M

+ M 1 2 3 4 5 1. On/Off 2. Prev/Decrease Volume 3. Play/Pause 4. Next/Increase Volume 5. Mode Rear Panel - Wiring Diagram ARC USB AUX OPTICAL DC IN DC 14V Power Adapter AC 230V~

HDMI Cable AUX Cable Optical Cable Dear Customer, Please read the instruction manual carefully before use and keep it in a safe place for future reference. IMPORTANT SAFEGUARDS Before use, ensure that the mains voltage corresponds to the rating of the unit. Place the unit in a cool, dry and clean place, free from vibrations. Do not place any objects such as vases full of liquid, on top of the unit. If liquid or a foreign object enters the unit, stop using it immediately, turn it off and remove the plug from the mains supply. Keep the unit away from direct sunlight. Handle the unit with care. Warning: There is uninsulated "dangerous high voltage" in the unit. To prevent electric shock, do not remove the cover or the rear plate yourself. Do not open the housing or try to repair the unit yourself otherwise the warranty will become invalid. Repairs or other operations must be conducted by a professional. When removing the plug from the mains supply or connecting or disconnecting the cable, do not pull on the power cable, rather grasp the plug/connector firmly. Make sure the power is off before connecting or disconnecting. When the unit is off, please remove the plug from the mains supply. Only use a soft, dry cloth to clean the unit. In extreme cases, mild detergents poured onto a soft cloth can be used to remove stubborn dirt. Never use volatile chemicals such as benzine or paint thinners as these will damage the unit. This unit can only be used in environments under elevation of 2000m, otherwise there may be potential safety hazards. Do not use the unit in tropical climates. otherwise there may be a safety risk. Do not block the vents otherwise the unit may overheat. TECHNICAL PARAMETERS Output power: 30W (main unit) Speaker unit: 2 " 2 (main unit) Sensitivity: 60dB Frequency range: 50Hz~16KHz SNR: 80dB TROUBLESHOOTING Check the adaptor connection to the unit as well as mains supply. Check whether the unit is turned on. Check whether the correct audio source has been selected. If the problem still cannot be resolved after going through the above checks, please contact a qualified technician. FEATURES ACCESSORIES USB, FM OPERATING INSTRUCTIONS Indicator AUX BLUETOOTH white white white white white white Battery Installation 1 2 3 4 5 6 7 8 14 13 12 11 10 9 PLAY/PAUSE 1.ON/OFF 2.MUTE 3. 4.PREV 5. 6.OPT 7.BT DECREASE VOLUME 8.MODE REPEAT 9. ARC 10. AUX 11. 12.NEXT 13. 14.EQ INCREASE VOLUME Mode button accessories unit. white Insert a USB memory device to the USB port Press Mode button repeatedly or the Mode key Ensure that your USB is stored with MP3 audio. Use the controls on the unit or remote control to make adjustments. Previous/Next Track. Repeat:Repeat single track by pressing Repeat key once or all tracks by pressing Repeat key twice. the other Mode button unit. mode, after which the white indicator will light up Make sure the audio setting of the sound source is set to HDMI. 1. 2. 1. 2. 3. 4. 5. 1. 2. 3. A3.5mm audio connecting cable is required (incl uded in the list of accessories) Connect one end of the 3.5mm audio connecting the other end to the 3.5mm Press the Mode button repatedly or the AUX to AUX mode after which the white indicator will light up or show AUX input interface of the unit. ut interface and Press MODE Button repeatedly, or the Bluetooth after which the white indicator will blink If the pairing is successful, the unit will make a sound. Turn on the Bluetooth on your device and search for PG-025. Once found, click on it to pair. Please note that the unit will automatically connect to this device (after one successful connection) in the future as long as the Bluetooth setting is turned on on both the unit and the device. 1. Open the battery cover as shown in the above figure. 2. Insert a new battery. 3. Replace the cover. Caution Used batteries should be recycled. Keep out of childrens reach. DO NOT use new and old batteries together. Change both the batteries at the same time. When not using the remote control for a long time,remove the batteries from the unit. Warning:All batteries(packed or in use)must not be exposed to high temperature such as direct sunshine or fire. FCC STATEMENT :

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate r adio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If th is equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

receiver is connected. FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Reorient or relocate the receiving an Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the Consult the dealer or an experienced radio/TV technician for help. tenna.

FX 2.0CH SOUNDBAR MODEL: PG-025 INPUT : DC 14V ==22.2A POWER CONSUMPTION: 30W FCC ID:2BDCA-PG-025 FC

i

fl

(U

(J

) 1 1 6 C:

I U J

.J y S fl I 0 E

8 r

-ETI GROUP LIMITED -

Communications Commission Fedeal Authorization Equipment 7435 Oakland Columbia, Mills MD 21046 Road and Evaluation Authorization Brancl1 Division

-AqentDesiqnati_Q_n 2/26/24 ETI GROUP LIMITED acknowledges States to act as the1agentfor service of process their consent for the following contact located in the United is sought for which authorization for the equipment

(FCC ID: [please insert FCC ID]):

2BDCA-PG-025 Name and company of U.S. agent:

Linkwld LLC U.S. address Physical FRN of U.S. agent:

0033625682 of agent:

1942 Broadway St. STE 314C, Boulder, CO, 80302, US Email address of U.S. agent:

Timothy.linkwld@proton.me Linkwld LLC acknowledges their obligation to accept service of process on behalf of ETI GROUP LIMITED. in the United States for no less than one year after either the grantee has its obligation to maintain an agent for ETI GROUP LIMITED with the FRN 0033845314 sericeof process permanently the conclusion equipment, and importation of any Commission-related all marketing terminated whichever is later. accepts of the applicable equipment within administrative or judicial proceeding involving the U.S., o the By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911 (d)(7). Sincerely, Signature

[Name]

David Wang

[Tilie]

SALES MANAGER

[Company]

ETI GROUP LIMITED Signature

(Name of U.S. agent]

[Title

(Company of U.S. agent]

Timothy Zhu Manager of U.S. agent] linkwld LLC in this lener The infonnation provided An cxpiondale for this lcner the granting does not exist. TCB. is based on the referenced rule parts ofTitlc In case the U.S. agent changes, 47 of the CFR as well as KDB 986446 DOI. 30 days via the grantee is obligated to notify the FCC within

- ETI GROUP LIMITED -

Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern:

3/22/24 We, [ETI GROUP LIMITED], hereby certify that the equipment for which authorization is sought (FCC ID:

covered equipment prohibited from receiving an equipment authorization pursuant to 2.903 of the FCC rules.

[2BDCA-PG-025]) is not We also certify that, as of the date of the filing of the application, we are not identified on the Covered List (https://www.fcc.gov/supplychain/coveredlist) as an entity producing covered equipment. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(b) and (d)(5) and (6). Sincerely, 2 0 V

, U

) i i

d n a Signature

[David Wang]

[Sales Manager]

[ETI GROUP LIMITED]

) i

) 5

) d

1 1 9 2 _ u q E d e r e v o C

l e d o m

_ 2 6 The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01.