Product Instruction Manual LED Product Name: LED downlight 53199101 Model No. 53199101 Manufacturer: Elec-tech International.,Co.Ltd 1 Address: Guangdong Province Zhihai City, Tanjiawan, No.1 Jinfeng Rd Tel0756-3390990 Fax0756-3390778 Webwww.electech.com.cn 1. Product Introduction 1.1. Product Description 1.2. oduct schematic diagram 2. Product features 1.1 Specification 10W AC 120V 60Hz
>90%
>0.9 SCR and APP dimmer
/
Electronic ratings
/W Rated Power/W
/V Rated Input voltage/V
/Hz Frequency/Hz
/% Rated Power efficiency PF Rated Power Factor Dimming method Photometric ratings LED / LED Type/Quantity
/Lm Lumen
/K Temprature/K
/Ra CRI Physical information Material operating temperature 45 wet location IP rating 125*125*72.9mm
(LWH)/mm Luminaire dimension(LWH)/mm 2835/28pcs3030/15pcs 625lm 2700-5000KR+G+B 90 ALPC 2 Method of application 2.1 (A) Installation schematic diagram(A) A A:Turn off the power supply. Check the dimension of recessed can and the lamp holder type to see whether the retrofit kit can fit the luminaire. B: E26 B: crew clockwise the E26 adaptor into the lamp holder. Tighten. C:
C: Connect the male to the female connector. D:
D: Squeeze the V shape clips to match the grooves on the inside of the can, and slide the luminaire up into the can firmly. E:
E: Make sure the trim ring is flush with ceiling. Turn on the light to check the luminaire working status. APP Controlling the Light with Bluetooth wireless technology 1 Turn on your LED downlight. Enable Bluetooth on your smart device. Open the Commercial Electric Lighting app, wait for the smart device to detect the downlight, and select the downlight to pair the device to the light. The light will blink four times if pairing is successful. 2 Now that the downlight is paired with your Bluetooth wireless technology enabled device, you can directly control the light whenever it is in range. 6 3 White Light(CCT) User Screen 4 RGB Color Light(RGB) User Screen 7 3.3 Maintenance Instruction
*
*Do Not use volatile solvent such as alcohol to clean the troffer.
*
*Use soft cotton cloth with suds to clean the troffer .
*
*Non-profecssional do Not attempt to take apart and repair the troffer .
*
*No disassemble the soft cord, if broken, please invite professional personnel or ask the manufacturer to change 3 Environmental requirement Operating temperature45 4 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. 8 Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. IC STATEMENT This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est suscept ible d'en compromettre le fonctionnement. 9