FCC ID: 2AN3JST001-B1 CC2538 Zigbee wireless module

PRODUCT SPECIFICATION ST-001-B1 User Manual 1 CONTENT FCC Statement...................................................................................................................................3 PRODUCT FEATURES ......................................................................................................................6 PRODUCT SPECIFICATIONS...........................................................................................................7 PIN ASSIGMENT................................................................................................................................8 MODULE PINOUT ........................................................................................................................... 10 MECHANICAL ................................................................................................................................. 11 ENVIRONMENTAL ......................................................................................................................... 12 OPERATING .......................................................................................................................................... 12 STORAGE.............................................................................................................................................. 12 2 FCC Statement:

Federal Communication Commission Interference StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiveris connected.Consult the dealer or an experienced radio/TV technician for help.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For product available in the USA/Canada market, only channel 1~15 can be operated. Selection of other channels is not possible.This device and its antenna(s) must not be co-

located with any other transmitters except in accordance with FCC multi transmitter product procedures.Referring to the multi transmitter policy, multiple transmitter(s) and module(s) can be operated simultaneously without C2PC. IMPORTANT NOTE:FCC Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. IMPORTANT NOTE:This module is intended for Equipment monitoring and equipment data collection. The Equipment monitoring and equipment data collection. is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated.Additional testing and certification may be necessary when multiple modules are used. 3 20 cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT:In the users manual of the end product, the end user has to be informed to keep at least 20 cm separation with the antenna while this end product is installed and operated. The enduser has to be informed that the FCC radio frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:The final end product must be labeled in a visible area with the following " Contains TX FCC ID: 2AN3JST001-B1 ". If the size of the end product is larger than 38.5x24mm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Third party Checklist The party below will implement the ST-001-B1 Module in host systems in accordance with the instructions specified in this document and the documents referenced herein. 1.The Third party will ensure the Module is integrated in a host systems using only the approved antenna model(s) described in this document. 2.The Third party will ensure the antenna placement inside the host system will maintain the required spacing to end user for RF Exposure compliance, as specified in this document. 3.If other radios are integrated inside the host with the ST-001-B1 Module, the Third party will contact its test lab, TCB or EverComm Opto Ltd. to determine if additional FCC compliance evaluation is required to meet FCC collocation rules. 4 4.The Third party will ensure end user documentation will contain the specified regulatory wording and ensure the host system and the Module itself are labeled as specified in this document. 5. The Third party will ensure the Module is programmed in the factory with compliant transmit power not exceeding the levels specified in this document.ST-001-B1 requests that the Third party acknowledge its receipt of this document and the above instructions. You may contact EverComm Opto Ltd. with any questions concerning this document or the responsibilities of the Third party. IMPORTANT NOTE:

IC Radiation Exposure Statement:This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. This module is intended for Third party. The Third party is still responsible for the IC compliance requirement of the end product, which integrates this module. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT:In the users manual of the end product, the end user has to be informed to keep at least 20 cm separation with the antenna while this end product is installed and operated. The enduser has to be informed that the IC radio-

frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:The final end product must be labeled in a visible area with the following " Contains TX IC: 2AN3JST001-B1 ". 5 PRODUCT FEATURES Star operation with up to Multiple active piconets with background scan and support for Star mode Does not support frequency hopping, this module uses a fixed frequency transmission method Low power consumption for meeting worldwide energy standards Operate at ISM frequency Band 2.4G Support 1-15 channel,2405-2475MHz Programmable Output Power up to 20dBm 2.4-GHz IEEE 802.15.4 Compliant RF Transceiver Excellent Receiver Sensitivity of 97 dBm Robustness to Interference With ACR of 44 dB RoHS compliance Low Halogen compliance Security Hardware Acceleration Future Proof AES-128/256, SHA2 Hardware Encryption Engine Optional ECC-128/256, RSA Hardware Acceleration Engine for Secure Key Radio Command Strobe Processor and Packet Handling Processor for Low-Level MAC Exchange Functionality Applications Smart Grid and Home Area Network Home and Building Automation 6 Intelligent Lighting Systems PRODUCT SPECIFICATIONS MAIN CHIPSET Texas Instruments CC2538 FUNCTIONAL SPECIFICATIONS 2.4-GHz IEEE 802.15.4 Compliant RF Transceiver Interface UART:4800,9600,19200,38400,115200 12-Bit ADC With 8 Channels and Configurable Resolution Frequency Range 2405MHz 2475MHz Transmit Output Power Output Power up to < +20dBm Receiver Sensitivity 97 dBm Data Rate 250KHz Antenna Type 2.4GHz 2dBi-dipole Module Operating Voltage

+5V 5% supply voltage 7 PIN ASSIGMENT Pin Pin Define 1 2 3-9 10 11 12 13 14 15 16 17 18 19 20 21 GND VIN GND PD0 PA7 PA6 PA5 PA4 GND GND PA3 PA2 PA1 PA0 PC0 I/O G I G I/O I/O I/O I/O I/O G G I/O I/O I/O I/O I/O Description Ground Input Voltage Maxima :+5V5%

Supply module voltage Ground GPIO port D pin 0 GPIO port A pin 7, ADC3 analog input AIN7 GPIO port A pin 6, ADC3 analog input AIN6 GPIO port A pin 5, ADC3 analog input AIN5 GPIO port A pin 4, ADC3 analog input AIN4 Ground Ground GPIO port A pin 3, ADC3 analog input AIN3 GPIO port A pin 2, ADC2 analog input AIN2 GPIO port A pin 1, ADC1 analog input AIN1 UART TX GPIO port A pin 0, ADC1 analog input AIN0 UART RX GPIO port C pin 0 8 22 23 24 25 26 27 28 29 30 31 32 33 34 35-

41 PC1 GND PC4 PC5 PB0 RST PB1 PB2 PB3 PB4 PB5 GND

+3.3V GND I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O G O G GPIO port C pin 1 Ground GPIO port C pin 4 GPIO port C pin 5 GPIO port B pin 0 SYSTEM Reset PIN GPIO port B pin 1 GPIO port B pin 2 GPIO port B pin 3 GPIO port B pin 4 GPIO port B pin 5 Ground Voltage regulator Output Ground 9 MODULE PINOUT 10 MECHANICAL PCB Thickness:1.2mm Module Thickness:3.51mm 11 ENVIRONMENTAL OPERATING Operating Temperature: 0 to 50 C (32 to 122 F) Relative Humidity: 5-90% (non-condensing) STORAGE Temperature: -40 to 80 C (-40 to 176 F) Relative Humidity: 5-95% (non-condensing) 12

EverComm Opto Ltd. Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2AN3JSTO01-B1. Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type File Name Block Diagram Block Diagram.pdf Schematics Schematics.pdf Operational Description Operational Description.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely,

(signature) EK Hin Gr L Che A Eric Chen/ Director EverComm Opto Ltd. Rev 11/20/07

MODULAR APPROVAL LETTER Modular Approval Requirement

(i) The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements.

(ii) The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with part 15 requirements under conditions of excessive data rates or over-modulation.

(iii) The modular transmitter must have its own power supply regulation.

(iv) The modular transmitter must comply with the antenna and transmission system requirements of 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a unique antenna coupler (at all connections between the module and the antenna, including the cable). The professional installation provision of 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section.

(v) The modular transmitter must be tested in a stand-

alone configuration

(vi) The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number.

(vii) The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer No Yes Yes, the modular transmitter has metal shielding. Yes, the modular transmitter uses CC2592 for buffered/

data inputs. Yes, the modular transmitter has its own power supply regulator. Yes, the antenna of the modular transmitter complies with FCC requirements. Yes, the modular transmitter is tested in a stand-alone configuration. Yes, when the module is installed inside another device, it will be labelled as contain transmitter module XXXXXXXXX Yes, the users manual has provide instructions

\\10.10.11.252\prj-2019\EverComm()\ST-001-B1\New\FCC \Modular-Approval-

Letter_140225.docx

EverComm Opto Ltd. Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: Dec. 17, 2019 SUBJECT: FCC Application for 2AN3JST001-Bl To Whom It May Concern:

We, the undersigned, hereby authorize Delia Feng _at_Cerpass Technology Corporation_ on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Delia Feng _ on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards,

(signature) 5 fy Ep Chen Eric Chen/ Director EverComm Opto Ltd.

\\10.10.11,252\prj-201 9\EverComm(H###)\ST-001-B I\New\FCC 28#\POA_Letter_140225.docx