This equipment should be installed and operated with a minumum distance of 20 cm between the radiator and your body. 2 3 4 5 PREPARATION FOR USE 6 CARE AND MAINTENANCE 7 LOCATION OF CONTROLS 1. FM Telescope Antenna 2. Carry Handle 3. VOLUME Control Knob 4. Decorative LED Blinking Mode Selection (Turn Off) Button 5. M (Memory) Button 6. /BAND (Stop/Radio Band Selection) Button 7. 8.
(Skip/Fast Search Backward) Button
(Skip/Fast Search Forward) Button 9.
/SCAN (Play - Pause/Radio Scan) Button 10. BT/CD (Bluetooth/CD Mode Selection) Button 11. CD Door 12. FINE TUNE (Radio Fine Tune) Knob 13. CD Door OPEN/CLOSE Area 14. POWER Indicator 15. LCD Display
(Bluetooth) Indicator 16. 17. Function Selector
(RadioBT/CD/AUX Power Off) 18. AUX (In) Jack 19. 20. AC~ Socket
(Headphone/Earphone) Jack 21. Battery Compartment 8 OPERATION RADIO:
1. Slide the Function Selector to RADIO position to turn on the radio. 2. Press the /BAND Button repeatedly to select AM or FM band as desire. The correspondence indicator AM or FM and the radio frequency will appear on the LCD Display. 3. Press and hold the
/SCAN button until the radio frequency on the LCD Display starts running to automatically search and will store the channel in PROG. 4. Press and hold the or Buttons play the previous/next available radio station. Repeat the same procedures until the desired radio station is searched and play. 5. If the reception is not good, turn the FINE TUNE Knob for better reception. 6. Turn the VOLUME Control Knob to adjust volume level as desired. 7. When finished listening, slide the Function Selector to OFF position to power off the unit. Radio stations preset:
1. Power on the radio and receive the desired radio station as the previous procedure. 2. Press the M Button, "P XX" will appear on the LCD Display. Press the or Buttons repeatedly to select the program number you want stored to. Then press the M Button again to 3. Repeat the same procedures until all the desired radio stations are stored into the program list.
(Up to 20 AM stations and 30 FM stations can be stored.) 4. After programming, press the desired stored radio station. or Buttons repeatedly in radio mode to select and play the This unit has a built-in ferrite rod antenna, which provides adequate reception in most areas. If reception is weak, turn the unit to improve reception. The FM Telescopic Antenna is for FM reception only. If reception is weak, adjust the length and the angle of the antenna. 9 store it. Antennas:
AM:
FM:
CD:
1.Slide the Function Selector to BT/CD/AUX position to turn on the CD. The LCD Display will illuminate and indicator CD will appear. 2.Press the OPEN/CLOSE Area on the CD Door to open it then place a CD disc on the center spindle, with the printed side face up. 3.Close the CD door by pressing the OPEN/CLOSE area. Wait a few seconds; the number of the total tracks will appear on the LCD Display. 4.Press the 5.During playback:
/SCAN Button to start playing the first track on the disc. Turn the VOLUME Control Knob to adjust volume level as desire. Press the
/SCAN Button to pause; press again to resume normal playback Press the Press and hold the or Buttons repeatedly to skip the tracks. or Buttons to fast searching the specific section. 6.To stop CD playback, press the /BAND Button. The total number of tracks will appear on the 7.When finished listening, slide the Function Selector to OFF position to power off the unit. display. Programmed Playback:
Up to 20 tracks can be programmed playback as follows:
1. In CD STOP playback mode, press the M Button. "PROG 1 -- will appear on the display and blink. 5. Press the blinking. 2. Select the first specific track to be programmed by pressing the or buttons repeatedly. 3. Press the M Button to store the selected track into the memory. 4. Repeat steps 2 and 3 until all the specific tracks are stored into the memory.
/SCAN Button to start program playback. The program indicator "PROG" will stop 6. To stop playback, press the /BAND Button. 7. To erase the program, press the /BAND Button again in stop mode. The program indicator will disappear on the display. Repeat/Random Playback:
1. During playback (or program playback), press the M Button once. The repeat one indicator REP will appear on the LCD Display. The current track will playback repeatedly. 2. During playback, press the M Button twice. The repeat all indicator REP ALL will appear on the 10 LCD Display. All the tracks on the current disc (or program) will be playback repeatedly. 3. During playback, press the M Button three times, the random indicator "RAND" will appear on the LCD Display. The unit will play the tracks randomly. 4. To cancel the repeat and random play functions, press the M Button repeatedly until all repeat/random playback indicators disappear on the LCD Display or press the /BAND Button to Note: Random playback is not available in program playback mode. stop playback. BT (BLUETOOTH):
BT pairing and play:
First time use or re-pairing the unit to a new BT Device, pair as follows:
1. Slide the Function Selector to BT/CD/AUX position to turn on the CD. The LCD Display will illuminate and indicator CD will appear. 2. Press the BT/CD Button on the top of the unit to switch the unit from CD mode to BT mode:
Indicator on the front of unit will illuminate and blink. The Indicate bt will appear on the LCD Display and blink. 3. Power on the external BT Device and enter to BT searching mode. Start pairing following the on screen instructions from the external BT Device. After paired, the indicate bt on the LCD Display and Indicator on the front of unit will stop blinking. 4. If pairing is complete you may now play music with your external BT Device. 5. During playback:
Turn the VOLUME Control Knob to adjust volume level as desire. Press the
/SCAN Button to pause; press again to resume normal playback. Press the Buttons repeatedly to skip the tracks. 6. When finished listening, slide the Function Selector to OFF position to power off the unit. or Notes:
1. When the external BT Device searched the unit, the model number MD6972 will appear on the display of external BT Device. 2. If while pairing you are asked for a code please try "0000" or "1234". Normal operation after pairing:
1. Slide the Function Selector to BT/CD/AUX position to turn on the CD. The LCD Display will illuminate and indicator CD will appear. 2. Press the BT/CD Button on the top of the unit to switch the unit from CD mode to BT mode:
The Indicator on the front of unit will illuminate and blink. 11 Indicate bt will appear on the LCD Display and blink. 3. Wait a few seconds until the unit is automatically paired to the external BT Device. The indicate bt on the LCD Display and Indicator on the front of unit will stop blinking. 4. After pairing is complete you may now play music with your external BT Device. AUX (in):
appear. NOTES:
1. Insert one end of the Audio Connect Cable (not included) to the AUX Out; Line Out or Phones Jack on the external Audio Player. 2. Insert the other end to the AUX (in) Jack on the left of unit. 3. Slide the Function Selector to BT/CD/AUX position to turn on the unit. The unit will automatically switch to AUX (In) mode. The LCD Display will illuminate and indicator AUX will 4. Play the music on the connected external Audio Player as usual. 5. Turn the VOLUME Knob to adjust volume level as desired. 6. When finished listening, slide the Function Selector to OFF position to power off the unit. Make sure the sound output level of the connected external Audio Device is on high level. Otherwise, sound will weak. If sound is distorting, reduce the volume of the connected external Audio Player or set the EQ mode of it to normal. DECORATIVE LED LIGHTS:
HEADPHONE JACK:
Press the Button on the top of unit repeatedly to set the blinking modes or turn it off as desired. For private listening, connect the 3.5mm plug from the Earphone/Headphone (not included) into the HEADPHONE Jack on the left of unit. Sound from speakers will be auto cut. 12 TROUBLESHOOTING Check the following before requesting service:
SYMPTOM POSSIBLE CAUSE POSSIBLE SOLUTION No power AC Power cord had not connected Connect the AC Cord to the rear of unit and any wall outlet having AC 120V~; 60Hz Volume of the unit was set to minimum Increase the volume level by turning the position VOLUME Control Knob clockwise No sound or sound weak Volume level of paired/connected Rise the volume level of the device is in low level Volume level too high paired/connected device Reduce the volume level by turning the VOLUME Control Knob counterclockwise Sound distortion Volume level of the connected/paired device Reduce the volume level of the too high connected/paired device Unplug the cable from AUX (In) Jack CD or BT not functioning Audio Connection Cable was inserted into the AUX (In) Jack The external BT Device had NOT paired to Pair the external BT Device to the unit as BT not functioning the unit The external BT Device too far from the unit Place the external BT device close to the page 11-12 unit Disc is dirty or scratched Try other discs CD not play CD disc incorrect install Place the CD disc on the center spindle with label side face up CD compartment door is not closed. Close CD door completely. GENERAL SPECIFICATIONS Power Source:
AC 120 V~; 60 Hz; 16 W, Or DC 12 V; 8 x C size batteries (Not included) BT Version: 5.0 BT Operation Distance:
32 Feet in open area Radio Frequency:
AM: 520-1710 kHz ;
Disc Compatible:
Impedance of Speakers:
FM: 87.5-108 MHz CD; CD-R; CD-RW 2 x 3 W; 4 ohm Audio power:
2 W per Channel (Total 4W, RMS) ACCESSORIES 1 x Owners Manual 1 x AC Power Cord SPECIFICATIONS AND ACCESSORIES ARE SUBJECT TO CHANGE WITHOUT NOTICE 13 14