EVERINT Approval Sheet Product Specification Part Description: Bluetooth Module Customer Part No:
BIGSOLON Part No: BT-MSO4 Acknowledgement of reception We have received the attached specification Date 2021. 08 .02 Company Dept. EVERINT BIXOLON R&D LAB Representative Dong-gil.Lee Received by Copyright 2021 by EVERINT, all rights reserved. 1 EVERINT Revision Record No Date Item Modifications Approved 1 2021. 08. 02 First Issued Copyright 2021 by EVERINT, all rights reserved. 2 EVERINT 1. Module Features
- Complies with Bluetooth Core Specification version 5.2
- Up to 96MHz integrated ARM M3 micro-controller
- Built-in Reference Clock: 24MHz
- RoHS Compliant 2. Applications
- Home automation gateways
- Heart rate monitors
- Wearables
- Thermometers
- Blood pressure monitors
- Mobile 3. Features
- Size (18mm X 28mm X 3.6mm )
- Surface Mountable Copyright 2021 by EVERINT, all rights reserved. 3 EVERINT 4. Electrical Characteristics Parameter Min Nor Max Unit Supply Voltage (VBAT, VDD_IO) 3.0 Operation Temperature
-30 3.3 25 3.6 85 V 5. External Reset An External active-low reset signal, BT_RESET(RESET), can be used to put the BT-
MSO4 in the reset state. An external voltage detector reset IC with 50ms delay is needed on the BT_RESET(RESET). The BT_RESET should be released only after the VDD_IO supply voltage level has been stabilized for 50ms. Copyright 2021 by EVERINT, all rights reserved. 5 EVERINT 7. Pin Description PIN No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Pin Name Description Pad Type GND GND GND GND NC BT_STATUS BT_RESET NC NC NC VBAT VDDIO GND GND GND NC PUART_TX PURT_CTS PUART_RX NC NC PUART_RTS BT_AT_CMD NC BT_DUT NC GND NC NC NC UART_RTS UART-CTS Ground connection Ground connection Ground connection Ground connection No connection Active-low reset input No connection No connection No connection Ground connection Ground connection Ground connection No connection No connection No connection No connection No connection Ground connection No connection No connection No connection D/L D/L Copyright 2021 by EVERINT, all rights reserved. 8 EVERINT 33 34 35 36 37 38 39 40 41 42 43 44 MOSI_C Serial flash memory reset(Active low) GND UART_TX UART_RX GND NC NC GND GND NC GND GND Ground connection D/L D/L Ground connection No connection No connection Ground connection Ground connection No connection Ground connection Ground connection Copyright 2021 by EVERINT, all rights reserved. 9 EVERINT 9.PIN MAP
<Top View>
Copyright 2021 by EVERINT, all rights reserved. 11 EVERINT 10. Dimension(unit :mm) Copyright 2021 by EVERINT, all rights reserved. 12 EVERINT
CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes: (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. RF Radiation Exposure Statement:
This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the ISED radio frequency (RF) Exposure rules as this equipment has very low levels of RF energy. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. RSS-102 RF Exposure Lantenne (ou les antennes) doit tre installe de faon maintenir tout instant une distance minimum de au moins 20 cm entre la source de radiation (lantenne) et toute personne physique. Cet appareil ne doit pas tre install ou utilis en conjonction avec une autre antenne ou Copyright 2021 by EVERINT, all rights reserved. 13 EVERINT metteur. IMPORTANT NOTE This device complies with FCC & ISED radiation exposure limits set forth for an uncontrolled environment. This device should be installed and must not be co-located or operating in conjunction with any other antenna or transmitter. This device is intended only for OEM integrators under the following conditions:
1) This module may not be co-located with any other transmitters or antennas. 2) The antenna must be installed such that 20cm is maintained between the antenna and users. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements with this module installed. In the event that these conditions cannot be met, then the FCC & IC authorizations are no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product including this module and obtaining separate FCC & IC authorizations.
- End Product Labeling To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product. Contains Transmitter module FCC ID: 2AKMF-BT-MSO4 IC: 22266-BTMSO4
- Manual Information to the End User The OEM integrator is responsible for ensuring the end-user has no manual instruction to remove or install module. The end user manual shall include all required regulatory information/warning as show in this manual. Copyright 2021 by EVERINT, all rights reserved. 14