IMPORTANT SAFETY INSTRUCTIONS FCC STATEMENT:
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. RF warning statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. 20. Service Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 21. Replacement parts When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original parts. Unauthorized substitutions may result in fire or electric shock or other hazards. 22. Safety check Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 23. Wall or ceiling mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer. 24. Damage requiring service Unplug this product from the wall outlet and refer service to qualified service personnel under the following conditions. a. When the power- supply cord or plug is damaged. b. If liquid has been spilled or objects have fallen into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an adjustment of other controls may result in damage and will require extensive work by a qualified technician to restore the product to its normal operation. e. If the product has been dropped or the cabinet has been damaged. f. When the product exhibits a distinct change in performance- this indicates a need for service. 25. Note to CATV system installer This reminder is provided to call the CATV system installer s attention to Article 820- 40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. 12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. An appliance and cart combination should be moved with care. Quick stop, excessive force and uneven surfaces may cause the appliance and cart combination to overturn. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. Power source This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For products intended to operate from battery power, or other source, refer to the operation instructions. 16. Power lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 17. Overloading Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock 18. Object and liquid entry Never push objects of any kind into the product through openings as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid on the product. 19. Outdoor antenna grounding If an outside antenna is connected to the product, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges. Section 810 of the National Electric Code ANSI/ NFPA 70 provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead- in wire to an antenna discharge product, size of grounding conductors, location of antenna- discharge product, connection to grounding electrodes and requirements for the grounding electrodes. POWER SOURCE The unit has a built-in rechargeable Li-ion battery. Recharge it before use or when it is consumed with the supplied AC/USB Adaptor as follows:
1. Connect the Micro USB Plug from the supplied USB Connection Cable to the Micro USB Port on the rear of unit. 2. Connect the Full size USB Plug to the USB Port on the supplied AC/USB Adaptor. 3. Plug the AC/USB Adaptor to the AC wall outlet having AC 100-240V~, 50/60Hz. 4. During charging, the Indicator on the top of unit will illuminate and blink. When finished charging:
The Indicator will stop blinking in power on mode. The Indicator will turn off in power off mode. LOCATION OF CONTROLS Top of unit:
Front of unit:
Rear of unit:
OPERATION Pairing or re-pairing the units to External BT Device In first time use or re-pairing to a BT Device, pairing it as below:
When finished listening,press and hold the Button on either unit until hear an audible prompt Power off from the speaker then release the button to power off both units. EB-1208b TROUBLESHOOTING GUIDE SPECIFICATIONS:
PACKAGE INCLUDES:
EVERY BRIGHT Protable Bluetooth Speaker System MODEL:EB-1208a IMPORTANT SAFETY INSTRUCTIONS FCC STATEMENT:
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. RF warning statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. 20. Service Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 21. Replacement parts When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original parts. Unauthorized substitutions may result in fire or electric shock or other hazards. 22. Safety check Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 23. Wall or ceiling mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer. 24. Damage requiring service Unplug this product from the wall outlet and refer service to qualified service personnel under the following conditions. a. When the power- supply cord or plug is damaged. b. If liquid has been spilled or objects have fallen into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an adjustment of other controls may result in damage and will require extensive work by a qualified technician to restore the product to its normal operation. e. If the product has been dropped or the cabinet has been damaged. f. When the product exhibits a distinct change in performance- this indicates a need for service. 25. Note to CATV system installer This reminder is provided to call the CATV system installer s attention to Article 820- 40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. 12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. An appliance and cart combination should be moved with care. Quick stop, excessive force and uneven surfaces may cause the appliance and cart combination to overturn. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. Power source This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For products intended to operate from battery power, or other source, refer to the operation instructions. 16. Power lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 17. Overloading Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock 18. Object and liquid entry Never push objects of any kind into the product through openings as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid on the product. 19. Outdoor antenna grounding If an outside antenna is connected to the product, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges. Section 810 of the National Electric Code ANSI/ NFPA 70 provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead- in wire to an antenna discharge product, size of grounding conductors, location of antenna- discharge product, connection to grounding electrodes and requirements for the grounding electrodes. POWER SOURCE The unit has a built-in rechargeable Li-ion battery. Recharge it before use or when it is consumed with the supplied AC/USB Adaptor as follows:
1. Connect the Micro USB Plug from the supplied USB Connection Cable to the Micro USB Port on the rear of unit. 2. Connect the Full size USB Plug to the USB Port on the supplied AC/USB Adaptor. 3. Plug the AC/USB Adaptor to the AC wall outlet having AC 100-240V~, 50/60Hz. 4. During charging, the Indicator on the top of unit will illuminate and blink. When finished charging:
The Indicator will stop blinking in power on mode. The Indicator will turn off in power off mode. LOCATION OF CONTROLS Top of unit:
Front of unit:
Rear of unit:
OPERATION Pairing or re-pairing the units to External BT Device In first time use or re-pairing to a BT Device, pairing it as below:
When finished listening,press and hold the Button on either unit until hear an audible prompt Power off from the speaker then release the button to power off both units. EB-1208a TROUBLESHOOTING GUIDE SPECIFICATIONS:
PACKAGE INCLUDES:
EVERY BRIGHT Protable Bluetooth Speaker System MODEL:EB-1208b IMPORTANT SAFETY INSTRUCTIONS FCC STATEMENT:
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. RF warning statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. 20. Service Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 21. Replacement parts When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original parts. Unauthorized substitutions may result in fire or electric shock or other hazards. 22. Safety check Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 23. Wall or ceiling mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer. 24. Damage requiring service Unplug this product from the wall outlet and refer service to qualified service personnel under the following conditions. a. When the power- supply cord or plug is damaged. b. If liquid has been spilled or objects have fallen into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an adjustment of other controls may result in damage and will require extensive work by a qualified technician to restore the product to its normal operation. e. If the product has been dropped or the cabinet has been damaged. f. When the product exhibits a distinct change in performance- this indicates a need for service. 25. Note to CATV system installer This reminder is provided to call the CATV system installer s attention to Article 820- 40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. 12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. An appliance and cart combination should be moved with care. Quick stop, excessive force and uneven surfaces may cause the appliance and cart combination to overturn. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. Power source This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For products intended to operate from battery power, or other source, refer to the operation instructions. 16. Power lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 17. Overloading Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock 18. Object and liquid entry Never push objects of any kind into the product through openings as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid on the product. 19. Outdoor antenna grounding If an outside antenna is connected to the product, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges. Section 810 of the National Electric Code ANSI/ NFPA 70 provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead- in wire to an antenna discharge product, size of grounding conductors, location of antenna- discharge product, connection to grounding electrodes and requirements for the grounding electrodes. POWER SOURCE The unit has a built-in rechargeable Li-ion battery. Recharge it before use or when it is consumed with the supplied AC/USB Adaptor as follows:
1. Connect the Micro USB Plug from the supplied USB Connection Cable to the Micro USB Port on the rear of unit. 2. Connect the Full size USB Plug to the USB Port on the supplied AC/USB Adaptor. 3. Plug the AC/USB Adaptor to the AC wall outlet having AC 100-240V~, 50/60Hz. 4. During charging, the Indicator on the top of unit will illuminate and blink. When finished charging:
The Indicator will stop blinking in power on mode. The Indicator will turn off in power off mode. LOCATION OF CONTROLS Top of unit:
Front of unit:
Rear of unit:
OPERATION Pairing or re-pairing the units to External BT Device In first time use or re-pairing to a BT Device, pairing it as below:
When finished listening,press and hold the Button on either unit until hear an audible prompt Power off from the speaker then release the button to power off both units. TROUBLESHOOTING GUIDE SPECIFICATIONS:
PACKAGE INCLUDES: