all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User Manual | Users Manual | 2.80 MiB | ||||
1 | Cover Letter(s) | |||||||
1 | Block Diagram | |||||||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | External Photos | |||||||
1 | Internal Photos | |||||||
1 | ID Label/Location Info | |||||||
1 | ID Label/Location Info | |||||||
1 | Operational Description | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos |
1 | User Manual | Users Manual | 2.80 MiB |
USER GUIDE Evolis Card Printer 201 All rights reserved. March 201. Ev Ref. KU-1-0-ENG Rev. A0 Copyright Evolis Card Printer March 201. All rights reserved. Copyright notice Users must observe the copyright regulations applicable in their country. This manual must not be photocopied, translated, reproduced or transmitted, in whole or in part, for any reason and by any electronic or mechanical means whatsoever without the express written consent of the Evolis Card Printer company. All the information contained in this document is subject to change without prior notice. Evolis Card Printer cannot be held liable for any errors that may be found in this manual, or for any loss or damage arising accidentally or as a result of dissemination or use of this manual. Trademarks
, Evolis Premium Suite and Evolis High Trust are trademarks of Evolis Card Printer. All other trademarks belong to their respective holders. Warranty Refer to the warranty notice supplied with your printer for warranty terms and conditions and limitations. Environmental information Evolis is committed to helping the environment by reducing the energy consumption of its products.
Recycling of end-of-life products The manufacture of the equipment that you have purchased required the extraction and use of natural resources. It may contain materials that are hazardous to health and the environment. To prevent the dispersal of such materials into our environment and reduce the pressure on our natural resources, we recommend that you use existing collection systems. These systems will appropriately re-use or recycle most of the materials in your end-of-life equipment. The crossed-out dustbin symbol on your device is a reminder to use these systems. If you need further information on collection, re-use and recycling systems, contact your local or regional waste management body.
www.evolis.com or by emailing the following address:
info@evolis.com. 2 About your new printer Thank you for choosing an Evolis printer. Using your new printer, you will be able to create a wide variety of high-quality cards and badges which can be printed in various thicknesses, colours and styles. This printer uses consumables and accessories available from Evolis. For further details, visit our website at www.evolis.com. Warranty registration Please register on line at www.evolis.com to receive our special offers and general information. Once on the website, click on Drivers and Support then on Register your printer serial number found on your printer. Getting started The purpose of this user guide is to guide you, step by step, through your printer and how it works. Take some time to read it in order to better understand your printer and its features, and to save time during installation and use.
emailing us at info@evolis.com. Contents The bookmarks found top left of your screen can be used to navigate between the various sections in this user guide. Icons The following icons are used in this manual to highlight important information:
Information providing further details or depth about certain points in the main text. Indicates that failing to take the recommended action is liable to damage your printer. This symbol indicates that a video showing the procedure is available on the www.evolis.com website and clicking on it takes you straight to on-line help. This symbol links to Evolis Print Center, accessible from your computer, which you can use to administer and manage you printer and change its settings. 3 1 Getting started 1-1 Unpacking
This list may vary depending on your location. The printer is shipped in special packaging designed to prevent any damage in transit. If you notice any visible damage, do not hesitate to contact the shipper and immediately inform your Evolis dealer, who will tell you the procedure to follow. Evolis takes great care over the quality of its packaging and we ask that you keep this packaging somewhere clean and dry. You will be asked for the full original packaging (outer box, inner wedges and protective bags) in the event that the printer is returned. If the printer is returned without its original packaging and components are damaged in transit, these components will no longer be covered by the warranty. You will be charged for new packaging for shipping the printer back to you. Accessories supplied with your printer:
Power supply unit - SWITCHBOX Type F10723-A.
Mains power cable.
USB cable. Installation, documentation and software CD-ROM.
If any of these components is missing, please contact your Evolis dealer. Use only the power supply unit supplied with your Evolis printer. SWITCHBOX Type F10723-A. Use only the USB cable supplied with your Evolis printer. The Evolis printer must be placed in a dry location, protected from dust and draughts but well-ventilated. Take
4 1-2 Description of the printer and its functions 1
A - Card input feeder B - Output hopper
- Control panel
- USB connectors
- Power cable socket
- Kensington lock 5 1
- Thermal print head
- Serial number label
(unplugged) before carrying out any work on it. Look at the getting started video described in the following section. 6 1 1-3 Installation 1-3a CONNECTING THE PRINTER
Connection to the power supply The printer must be connected to a properly protected and earthed electrical installation. FI: Laite on liitettv suojamaadoitus koskettimilla varustettuun pistorasiaan. NO: Apparatet m tilkoples jordet stikkontakt. SE: Apparaten skall anslutas till jordat uttag.
Connect the power cable to the power supply unit, then plug the power supply unit
The printer is powered on: the control panel lights up showing the printer is working connector into the printer. properly. If the control panel does not light, then either installation has not been carried out correctly or the printer is not working properly. Check the installation. Before attempting any maintenance, ensure that the power cable is always unplugged. For your personal safety, ensure that the cable and power supply unit remain easy to access, especially in the event of an emergency. To save energy, the printer will automatically switch itself to standby mode after 10 minutes of inactivity. The printer switches to hibernation mode after 30 minutes in standby mode.
Connecting the USB cable Under no circumstances should you connect the USB data cable before installation of the printer driver is complete. Refer to the section on printer driver installation for further details, and follow the instructions carefully. 7 1 1-3b RIBBONS Evolis original High Trust ribbons optimise your printers operation and avoid causing damage to it. The use of ribbons from other suppliers is liable to damage your printer and voids the manufacturers warranty for the printer. For optimum print quality, Evolis recommends that the printer is fully cleaned every time the ribbon is changed. See the Servicing and Maintenance section of this manual.
Fitting the ribbon The printer automatically recognises the ribbon inserted.
Open the cover.
Insert the ribbon as shown.
Close the cover and press until a click is heard.
8
1 1-3c CARDS
Use only the card types recommended by Evolis.
Keep your cards protected from dust.
Loading the cards
Open the card feeder.
Insert the cards, a maximum of 50 cards of thickness 0.76 mm. Ensure the cards are positioned as illustrated in the diagram.
Close the feeder.
99
1
Removing printed cards Once the print cycle is complete, cards are delivered into the output hopper below the card feeder. This output hopper is designed to collect the printed and/or encoded cards. The printer is equipped with an output hopper with a maximum capacity of 20 x 0.76 mm cards. 10 2 Printing 2-1 Installing the print driver
To install a print driver, insert the CD into your computer and select the print driver menu. A program will guide you through the entire installation process. Do not connect your USB cable to your computer until prompted to do so by the installation program. For the connection procedure, see the section on Connecting the Printer.
administrator rights to install the driver.
2 2-2 Managing the print settings Once the ribbon has been installed, your Evolis printer will automatically adapt its parameters and settings to suit the ribbon.
To access this application:
From the Start button on the bottom left of your screen in the Windows task bar, select All programs, Evolis Card Printer, Evolis Premium Suite, Evolis Print Center
The application displays all connected Evolis printers.
2
Select the desired printer.
Right click the name of the printer, select Properties to access the settings or double (left) click the name of the printer.
dealer for any advice and assistance needed before making any changes. Please refer to the Evolis Print Center manual for more detail on the meanings of each of the settings.
2
The Evolis Printer Manager has an additional function allowing the printer to communicate with the user .
Messages about the maintenance of the printer.
Messages and alerts associated with the ribbons, their compatibility with your printer or the nature of your print requests.
Warnings about problems which have stopped the printer. When the Evolis Printer Manager is active, a small icon is displayed in the bar on the bottom right of your screen. The colour of the icon varies according to the status of the printer:
: Printer ready
Orange: Information message issued - printing stopped
Red: Warning message issued - printing stopped
: Printer in hibernation mode, disconnected or communication interrupted.
Depending on the type of message, you can either:
Interrupt the printing task. Restart the task. The Evolis Printer Manager service can be disabled by right-clicking the Evolis icon on the status bar.
installed on your computer. The Evolis Printer Manager service is the best way of monitoring your printer effectively from your workstation.
2 2-4 Printing a card
MS-Access, Ms-Excel, MS-PowerPoint).
In Microsoft Word After having set the Evolis printer as the default:
Start the MS-Word application
Click on the File in the menu bar, then on Page Setup
In the Margins tab, set all margins to 0, then in the Orientation section, select Landscape.
The Paper tab has a Paper Size option, select CR80 Card
For Word 2010: click the Page layout tab, then click on Size and select CR80 Card
Close the window by clicking OK. Your Word window should now look like this:
up a card:
Logo and Illustration
Fixed and variable texts
Bar Code, etc. Once ready, click on File and then on Print.
3 Maintenance 3-1 General warranty information
instructions given below to ensure that it runs satisfactorily. Keep your warranty cover!
The manufacturers warranty is subject to strict adherence to the routine servicing and maintenance instructions, and in particular the printer cleaning cycles. Any failure to follow the maintenance and servicing procedures described in this section voids the print head warranty. Evolis declines any liability where there has been a failure to carry out required maintenance on the printer. The print head is a wearing part and an extremely sensitive printer component. Its useful life can be seriously curtailed by the presence of dust, liquids or solids in the printers immediate environment, on the print head or on the cards. Users must take all necessary precautions to insert only clean cards, free of dust deposits or foreign bodies, into the machine. The frequency and quality of cleaning are decisive factors enabling users to extend the print heads useful life and to ensure excellent print quality. Particular care must therefore be taken with cleaning. Users must comply with the servicing and maintenance instructions as fully described in this section. In addition, the use of Evolis brand ribbons (Evolis High Trust) also ensures that your equipment operates properly. Use of ribbons not approved by Evolis may as a consequence affect the quality and reliability of print jobs, produce low quality printed output and even affect the printers operation. The manufacturers warranty does not cover physical damage or quality problems caused by using non-
Evolis approved ribbons. Evolis provides replacement parts and consumables that you can refer to within this user guide or by visiting the website at www.evolis.com.
3-2 Routine printer cleaning 3 The print head warranty is directly linked to routine cleaning of your printer.
Recommended cleaning cycle: whenever the ribbon is changed Mandatory cleaning cycle: when the cleaning warning is triggered Servicing accessory: cleaning card.
been inserted. You should proceed with the routine cleaning of your printer as soon as the warning is triggered. If you continue to run the printer despite the warning and if the warning light remains lit, the print head warranty will be automatically voided owing to a failure to comply with your contractual maintenance obligations.
3 Follow the procedure below to ensure you have carried out regular cleaning properly:
Repeatedly running the adhesive card through the printer cleans the cleaning roller in order to maintain print quality and increases the service life of the print head.
Remove the cover from the printer as shown.
Using the lever, set the card thickness to the MAX position.
Remove the ribbon as shown on the diagram.
Close the cover and check it has clicked shut.
3
Open the feeder.
Remove any cards present in the feeder.
Close the feeder.
Double click the cleaning button on the control panel before inserting the cleaning card.
and insert the cleaning card into the manual feeder as shown, adhesive side up . Cleaning starts.
The used cleaning card is ejected automatically by the manual feeder.
The used cleaning c is ejected automatically by the manual tarts.
Routine cleaning may also be carried out from the Evolis Print Center by clicking on "Start cleaning". Before using your printer, remember to reset the gauge to the desired card thickness.
3 3-3 SERVICING THE PRINT HEAD Recommended cleaning cycle: every 5 routine cleaning cycles. Servicing accessory: cleaning pen Unplug the printer from its power supply before cleaning the print head. Follow the cleaning cycles scrupulously. Avoid any contact between the print head and any metal or sharp objects.
the print head. The cleaning pen can be used up to 8 times for cleaning the print head. Follow the procedure below:
Remove the cover from the cleaning pen.
Close the cover. Reconnect the printer.
Wait for 2 minutes after cleaning before using your printer.
4 Help This section gives a number of suggestions allowing problems that may arise when using your printer to be pinpointed. If you do not manage to solve your problem, this section also explains how to contact Evolis technical support. 4-1 Warnings and diagnosis Although the Evolis printer was designed to work independently, keeping user involvement to a minimum, it may nonetheless prove useful to gain some familiarity with the main warnings. 4-1a CONTROL PANEL WARNINGS See section 1 - Description of the printer and its functions for further details about the control panel. Cards and ribbon
Pushbutton OFF STEADY LIGHT FLASHING
4 PRINTER READY
The printer is ready to receive data. PROCESSING
The printer is receiving data. RIBBON CARDS
End of ribbon.
The ribbon is not correctly
The ribbon is torn.
The ribbon is not recognized. Check the condition of the ribbon in the printer. If you have a print job in progress, this restarts with a new card.
feeder. Put cards back into the feeder - the process starts again.
Card loading error. Check cards have been loaded. For any other problem contact your Evolis dealer.
4 PRINTER COVER OPEN MECHANICAL ERROR
The printer cover is open.
Card jammed in the Close the cover again. The printer starts up. printer.
Mechanical component fault. Open the cover and hold down the pushbutton in order to eject the jammed card. For more details, refer to section 4-3b. If the problem persists, contact your Evolis dealer for assistance. COOLING MODE
The cooling system has been activated. The printer pauses for a few seconds and restarts once it has returned to its normal operating temperature. FIRMWARE UPDATE
The printer is updating its Firmware. The printer restarts following the update.
4 4-2 Diagnosis help
to help you as effectively as possible. 4-2a PRINTING A TECHNICAL TEST CARD We recommend that you print a technical test card to ensure that your printer is working properly. This card shows various items of
these by your dealer.
Printing a technical test card
Check that there is a ribbon and card in the printer.
Press the pushbutton for four seconds. All the warning lights go out.
Press and hold down the pushbutton again.
The pushbutton light comes on.
The printed card is ejected into the output hopper. Printing the technical test card can also be launched from the Evolis Print Center. 4-2b PRINTING A GRAPHIC TEST CARD The graphic test card is used to check the print quality in colour or monochrome, the offsets and whether the ribbon is synchronised correctly.
Evolis Print Center, select System information and click on the Test cards tab. Then click the Graphic test card button. The card is printed and the printed card is ejected into the output hopper. Printing the graphic test card can only be launched from the Evolis Print Center.
4
In Evolis Print Center, double click the name of the printer to display its Properties.
Click System information, then System information.
4 4-3 Troubleshooting Do not attempt to use tools or other items to repair your printer in the event of problems, in case major damage is caused. 4-3a PRINTING PROBLEMS
Nothing prints
Check the print driver
Check the printer's power supply
Check that the printer is selected as the default printer. Check that the power cable is correctly connected to the printer and to a working electrical socket. Check that the printer is on and that the pushbutton is lit. Make sure you are using the power supply unit supplied with the printer.
Check the USB cable
Check the ribbon
Check the cards
Print a test card Check that the USB cable is connecting the printer to your computer.
Check that there are cards in the card feeder. Check that no cards are jammed in the printer. See elsewhere in this section for the procedure to be followed.
Blank card ejected
Check the ribbon
The print head may be damaged
Print a test card. If the test card does not print, contact an Evolis dealer for technical support or visit the website at www.evolis.com.
4
Poor print quality Small blemishes on the card Horizontal white lines Blurred image
The card surface may be dirty. Check that your cards are perfectly clean. Use new cards.
Cleaning roller or print head clogged. Run a cleaning cycle.
Check that there are no wrinkles on the ribbon surface.
Print head dirty or damaged. Clean or replace the print head.
Check that the ribbon is correctly positioned in the printer.
Poor ribbon synchronisation. Open and close the printer cover to synchronise the ribbon.
Dirty printer or cleaning roller. Clean the printer
Use of incompatible cards.
We recommend that you obtain your cards from an Evolis dealer.
4 Check that no area of the card design to be printed is outside the print margins.
If irregular characters are printed, check that you are in fact using the USB cable supplied with your printer. Check the connection between the computer and the printer. Try using another cable of the same type.
Partial or incorrect printing
Check the print settings
Check the interface cable Clean the printer, especially the cleaning roller. See the maintenance section.
Check that the printer is clean
Check that the cards are clean
Check the ribbon
Check the print head
Check that the ribbon spools freely. Store your cards protected from dust. Should horizontal straight lines appear on printed cards, it is likely that the print head is dirty or damaged. See the section on maintenance and troubleshooting. If the problem persists, contact an Evolis dealer or visit the website at www.evolis.com.
4 4-3b FREEING JAMMED CARDS Control panel displays:
MECHANICAL ERROR
Card jammed in the printer. Print jobs are interrupted. Do not turn off your printer as this cancels pending print jobs in the printers memory. Remove the card as follows:
Open the printer cover and remove the ribbon.
Press the pushbutton to turn the card transport rollers. If the card is still stuck inside the printer, slide it manually towards
Replace the ribbon, then close the printer cover.
To prevent card jams: Check that the card thickness gauge is correctly adjusted.
in this manual.
4 4-3c REPLACING THE PRINT HEAD The print head is a sensitive component of your equipment. It determines the print quality, and regular servicing along with an immediate
replaced. Evolis has designed a unique device enabling users to undertake such replacement with no tools needed, simply by following the instructions very carefully. Before doing anything else, please contact your Evolis dealer in order to check the advisability of replacing the print head. The dealer will supply a new print head if need be. For more information on print head warranties, refer to the Evolis warranty booklet.
4 To exchange the print head, please proceed as follows:
Before changing the print head, please unplug the power cable.
Step 1 - Removing the defective print head
Open the printer cover.
Locate the print head.
Press on the plastic part behind the head (pressure plate) and pull on the head with the other hand as shown in the
Tilt the head carefully downwards and disconnect the connector linked to the cable without using force on the diagram in order to free the lugs from the holding fork, then remove the lugs from their slots. mechanism. mechanism.m.m.m.m.m.m.m.m.m.m.m.m.m.m.m.m.m.m.m.m.
4
Step 2 - Installing the new print head
Take the new head and insert it vertically (white connector upwards) raising it in the two guides so as to trap the lugs of the fork in their slots . Then lower it by pressing on the two forks , a click will be heard.
Connect the cable into its socket, making sure it is the right way round. Do not use any force, as this part is relatively
The head is back in position.
fragile. Press down on each side of the connector to ensure a good connection is made.
4
Power up the printer and check that it is properly connected to a computer on which the printers Evolis Print Center is
In Maintenance of Evolis Print Center, click on the Change print head tab.
Enter PKN no., the number you noted down in step 2. Then click . installed. If the print head kit number is not entered correctly, printer malfunctions may occur and the warranty may be voided.
4 4-3d UPDATING THE FIRMWARE (under Windows)
Before any update, please contact your Evolis dealer who will be able to guide you on the advisability or otherwise of carrying out an
dealer. Updates can be downloaded from the website at www.evolis.com:
Support & Drivers menu, then select your printer model and click on the Print drivers and Firmware link.
When requested by the program, follow the instructions in order to select the printer and start the operation. The
that the printer is not working properly. Check the connection cables and run a new update. The update is complete, and your equipment is ready to customise your cards. Never interrupt the transfer between computer and printer during the download phase (powering off the printer or computer, unplugging a cable). This would result in a complete inability to restart the printer. Should such an incident occur, please contact your Evolis dealer, who will replace your printers processing board.
4 4-3e UPDATING THE PRINT DRIVER
Before any update, please contact your Evolis dealer who will be able to guide you on the advisability or otherwise of carrying out an upgrade. Updates can be downloaded from the website at www.evolis.com:
Support & Drivers menu, then select your printer model and click on the Print drivers and Firmware link.
For more details about the procedure, please see the Installing the print driver section.
4 4-4 Technical support
If you do not manage to solve your problem, you can obtain further information and help from the Evolis partner network. 4-4a EVOLIS PARTNER NETWORK For any unresolved technical problem, contact an Evolis dealer. If you do not know any Evolis dealers, visit the www.evolis.com website and send us your question. Evolis will pass on the contact details of your nearest Evolis dealer. When calling an Evolis dealer, you do need to be close to your computer and ready to provide the following information:
A description of the incident that has occurred
A description of the steps that you have taken to resolve the problem.
www.evolis.com website includes a number of aspects related to day-to-day use of your printer. 4-4b FINDING INFORMATION ON WWW.EVOLIS.COM
Drivers and Support section on the Evolis website at www.evolis.com.
printers, and an FAQ* section giving answers to the most frequently asked questions.
*FAQ: Frequently Asked Questions
A Appendix A
This section presents your printers technical printing properties.
General technical features Single side print module, edge-to-edge printing
Colour sublimation and monochrome thermal transfer
0 dpi print head (11.8 dots/mm)
16 million colours
16MB RAM
Printing speed Full card print
Full card print
Card management and technical data
Automatic feeder
Feeder capacity: 50 cards (0.76 mm 30 mil)
Output hopper capacity: 20 cards (0.76 mm 30 mil) Card types: PVC and composite PVC cards, recycled PET cards, PET, ABS1 and special clear overlaid cards1
Card format: ISO CR80 - ISO 7810 (53,98 mm x 85,60 mm) 1
A
Ribbons To maximise the quality and lifetime of the printed cards, the service life of your print head and the overall reliability of your printer, use Evolis High Trust ribbons.
Ribbon inserted in a cassette to make handling easier
Integrated ribbon saving for monochrome printing
Ribbon:
1
1
Ports/connectivity
USB 1.1 (compatible 3.0)
Ethernet port available as an option.
Display
LEDs
1:
1 Dependant on your version of Windows
Software
Supplied with Evolis Premium Suite for Windows:
1
2
Other platforms:
1 2 For older versions of Windows, upon request only
A
Warranty conditions
years' warranty (printer and print head)
Warranty extensions available (contact your Evolis reseller)
Dimensions and weight Dimensions (H x W x L): 1 x 20 x mm
Weight: kg
Acoustics (tested in accordance with ISO 7779)
Sound pressure in assistant positions LpAm
Security
Kensington security lock
Data encryption for magnetic encoding1 1 Available for the Expert range and above
Standby mode and reduced power consumption
Printer
Printer meets the Energy Related Products Directive, ErP, 2009/125/EC
Contents of the packaging
Printer
CD-ROM with printer driver, user manuals
USB cable
Power supply unit
Power supply lead (differs according to region)
A
Options & accessories
Ethernet TCP-IP1
CE, FCC, IEC, VCCI, CCC, KC ErP 2009/125/CE, , RoHS
Power supply
Environment
Min/max operating temperature: 15 / 30 C (59 / 86 F)
Humidity: 20% to 65% without condensation
Min/max storage temperature: 5 / +70 C (23 / 158 F)
Storage humidity: 20% to 70% without condensation
Ventilation in operation: open air
Other
Resident fonts
B Appendix B B1 - Compliance statements In this section, you will find the certifications for your Evolis printer. Compliance statements Concerning Safety and Electromagnetic Compatibility of Radio Equipment (R&TTE 1999/5/CE, 2006/95/CE and 2004/108/CE Directives) Manufacturer name:
Manufacturer address:
Evolis Card Printer 14, avenue de la Fontaine Z.I. Angers Beaucouz 49070 Beaucouz, France Badgy100 & Badgy200 2014 Equipment name:
Year of manufacture:
I, the undersigned, Serge Olivier, Declare under my own responsibility, that the product described above complies with the essential applicable requirements of the 1999/5/CE, 2006/95/CE and 2004/108/CE directives:
Article 3.1 b: (electromagnetic compatibility protection requirement) Safety standard applied EN60950-1:2006 + A11: 2009 + A1: 2010 + A12: 2011 Article 3.1 b: (electromagnetic compatibility protection requirements) EMC standard applied EN50364:2001 EN62311:2008 EN55022:2006 + A1 EN55024:1998 + A1 + A2 EN61000-3-2:2006 EN61000-3-3:2008 EN301489-3:v1.4.1 Article 3.2: (Good use of the radio frequency spectrum to avoid undesirable interferences) EMC standard applied Full name: Serge Olivier Position: R&D Director Date: 2014 Signature:
EN302291-2 v1.1.1 EUROPE - Norway Only: This product is designed for IT power system with phase-
to-phase voltage 230V. Earth grounding is via the polarized, 3-wire power cord. FI: Laite on liitettv suojamaadoitus koskettimilla varustettuun pistorasiaan SE: Apparaten skall anslutas till jordat uttag NO: Apparatet m tilkoples jordet stikkontakt 41 FCC Federal Communications Commission notice Radio frequency interference in the United States The Badgy100 and Badgy 200 models complie with the following specification: FCC Part 15, Subpart A, Section 15.107(a) and Section 15.109(a) Class B Digital device Additional information:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try the following measures: - Reorient or relocate the receiving antenna.
- Increase the distance between the equipment and the radio or television.
- Connect the equipment to a circuit other than that to which the receiver is connected.
- Consult the supplier or an experienced radio/TV technician. Use of a shielded twisted pair cable is necessary to comply with the restrictions laid down by part 15 of the FCC Rules for Class B digital devices. Pursuant to Part 15.21 of the FCC Rules, any changes or modifications made to this equipment without the express, written consent of Evolis Card Printer may cause harmful interference and void the FCC authorisation to operate this equipment. This equipment complies with FCCs radiation exposure limits set forth for an uncontrolled environment under the following conditions :
1.This equipment should be installed and operated such that a minimum separation distance of 20 cm is maintained between the radiator (antenna) and users/nearby persons body at all times. 2.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with the Industry Canada CNRs applicable to licence-exempt audio devices. Their use is authorised subject to the following two conditions: (1) the device must not cause interference and (2), the user of the device must accept any radio interference to which they may be subject even if the jamming is liable to adversely affect operation. Japanese radio frequency interference (vCCI) This equipment is Class B information technology equipment based on the rules laid down by the Voluntary Control Council For Interference by Information Technology Equipment (VCCI). Its use in or close to a residential area may cause radio interference, in which case, you must take appropriate steps.
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2014-03-17 | 13.56 ~ 13.56 | DXX - Part 15 Low Power Communication Device Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2014-03-17
|
||||
1 | Applicant's complete, legal business name |
EVOLIS
|
||||
1 | FCC Registration Number (FRN) |
0020754776
|
||||
1 | Physical Address |
14 avenue de la fontaine
|
||||
1 |
49070
|
|||||
1 |
BEAUCOUZE
|
|||||
1 |
France
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
T******@TIMCOENGR.COM
|
||||
1 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
ZFX
|
||||
1 | Equipment Product Code |
0030
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
S****** O********
|
||||
1 | Title |
General Manager
|
||||
1 | Telephone Number |
33241********
|
||||
1 | Fax Number |
33241********
|
||||
1 |
s******@evolis.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DXX - Part 15 Low Power Communication Device Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | RFID IDENTIFY THE RIBBON AND SET THE PARAMETERS | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
EMITECH Angers
|
||||
1 | Name |
O******** R******
|
||||
1 | Telephone Number |
33-2-********
|
||||
1 | Fax Number |
33-2-********
|
||||
1 |
o******@emitech.fr
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 13.56000000 | 13.56000000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC