RFID Module CP013463 INTEGRATION MANUAL 2021-10-15 RFID module CP013463 FCC Certification The OEM Integrators are responsible for ensuring that the end-user has no manual instructions to remove or install module. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help Authorized antennas:
The antenna is fixed and integrated in the reader. It cannot be removed.. The module is limited to OEM installation ONLY This modular is used exclusively by Evolis This equipment complies with FCCs radiation exposure limits set forth for an uncontrolled environment under the following conditions:
1. This equipment should be installed and operated such that a minimum separation distance of 20cm is maintained between the radiator (antenna) and users/nearby persons body at all times. 2. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The RF module has been certified for mobile and fixed applications. If the module will be used for portable application the device must undergo SAR testing or MPE evaluation. In this case, a separate approval is required for all other operating configurations. Any changes or modifications to this module not expressly approved by Evolis may cause, harmful interference and void the FCC authorization to operate this equipment 1/6 RFID Module CP013463 INTEGRATION MANUAL 2021-10-15 Moreover, the host equipment must be labelled as follows:
Contains Transmitter Module FCC ID : ZFX0011 or Contains FCC ID : ZFX0011 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Example :
Name:
Model:
Type:
P/N:
S/N:
DC Input:
Zenius ZN1U0000RS 10000194536 24V DC 2.7A Contains Contient FCC ID: ZFX0011 IC: 9609A-0011 Only use power supply provided with the printer This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference
(2) this device must accept any interference received, Including interference that may cause undesired operation. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. This Class B digital apparatus complies with Canadian ICES-003. Evolis Made in France 2/6 RFID Module CP013463 INTEGRATION MANUAL 2021-10-15 Additional information RFID module CP013463 should only be used on Evolis printer. RFID module CP013463 should only be installed by a Evolis technician. 1) The shielding of RF is provided by the printer frame. The printer frame is made of XC steel or plastic carbon force. 2) Power supply regulation is provided by the motherboard. The motherboard provides +3.3 volts. 3) When a response is received from the card, the response frame is decoded by NXP SLRC 610 and the resulting bytes are stored in SRAM buffer memory and the memory of printer mother board. 4) The printer can have another RF module used to the personalization of printed cards. In this case, it is the motherboard that makes sure a single RF module is running. 5) Assembly Printer frame RFID module CP013463 Twisted cable Length:
10 to 13 cm Printer motherboard 3/6 RFID Module CP013463 INTEGRATION MANUAL 2021-10-15 RFID module CP013463 IC Certification This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1) Lappareil ne doit pas produire de brouillage. 2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This radio transmitter (IC: 9609A-0011) has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Le prsent metteur radio (IC : 9609A-0011) t approuv par Innovation, Sciences et Dveloppement conomique Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'metteur. Authorized antennas / Antennes autorises :
The antenna is fixed and integrated in the reader. It cannot be removed.. Lantenne est fixe et intgre au lecteur. Elle est non dmontable. This equipment complies with RSS102s radiation exposure limits set forth for an uncontrolled environment under the following conditions:
1. This equipment should be installed and operated such that a minimum separation distance of 20cm is maintained between the radiator (antenna) and users/nearby persons body at all times. 2. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The RF module has been certified for mobile and fixed applications. If the module will be used for portable application the device must undergo SAR testing or MPE evaluation. In this case, a separate approval is required for all other operating configurations. 4/6 RFID Module CP013463 INTEGRATION MANUAL 2021-10-15 Cet quipement est conforme aux limites dexpositions de la CNR102 applicables pour un environnement non contrl aux conditions suivantes :
1. Cet quipement devra tre install et fonctionner de telle manire quune distance minimale de sparation de 20 cm soit maintenue entre la partie rayonnante (lantenne) et lutilisateur / les personnes proximit tout moment. 2 Cet metteur ne doit pas tre co-localis ou oprer en conjonction avec toute autre antenne ou metteur. Le module RF a t certifi pour les applications mobiles et fixes. Si le module est utilis pour une application portable, l'appareil doit subir un test DAS ou de lvaluation de lexposition maximale permise. Dans ce cas, une approbation spare est requise pour toutes les autres configurations de fonctionnement. Informations devant figurer sur ltiquette de limprimante:
Contains Contient IC: 9609A-0011 IC: 9609A-0011 Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. This Class B digital apparatus complies with Canadian ICES-003. Exemple :
Name:
Model:
Type:
P/N:
S/N:
DC Input:
Zenius ZN1U0000RS 10000194536 24V DC 2.7A Contains Contient FCC ID: ZFX0011 IC: 9609A-0011 Only use power supply provided with the printer This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference
(2) this device must accept any interference received, Including interference that may cause undesired operation. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. This Class B digital apparatus complies with Canadian ICES-003. Evolis Made in France 5/6 RFID Module CP013463 INTEGRATION MANUAL 2021-10-15 Spcificit du module RFID CP013463 Le module RFID CP013463 ne doit tre utilis que sur des imprimantes EVOLIS. Le module RFID CP013463 ne doit tre install que par un technicien Evolis. 1) Le blindage de la zone RF est assur par le chssis de limprimante qui est soit mtallique (Acier XC) ou en plastique charg carbone. 2) Lalimentation rgule 3.3 volts est assure par le carte mre de limprimante. 3) La bufferisation des donnes est assure par deux lments, via la SRAM du lecteur NXP SLRC610 et la carte mre de limprimante. 4) Limprimante peut accueillir un autre module RF pour la personnalisation des cartes, Dans ce cas cest la carte mre qui assure quil ny est quun seul module RF qui mette un instant T. 5) Montage Chssis imprimante Carte RFID CP013463 Cble torsad longueur :
10 13 cm Carte mre 6/6