Product Introduction Smart Relay uses Wi-Fi technology and may be used in different loads, including incandescent lamps, halogen lamps, LED lamps and fluorescent lamps. It is small enough to be installed in light switch boxes and body of most light fixtures. This device uses Apple HomeKit technology for remote control and inter-operation. 1 Connect wires per wiring diagram as follows Caution: If you have purchased a Smart Switch Sub-Assembly to use with it, please follow the installation instructions on the Smart Switch Sub-Assembly manual. With Smart Relay, you can turn a traditional lamp into a HomeKit smart lamp. It is recommended to install Smart Relay near the lamp. Fastening screws Fixing hole RESET button Indicator light Panel Connection port In-Wall Relay Switch Smart Relay Instruction Manual Rev. A-031821 P/N SRHW01
*Please see separate Evvr Smart Switch Sub-Assembly manual for complete instructions. Max. Load Power Complete Accessories Include Technical Specifications Model Number SRHW01 Input Voltage AC 85V~245V AC 110V/300W AC 220V/600W Min. Load Power No limit Applicable to Operating Temperature Light Fixtures 0~40C
(32~104F) Relative Humidity 5~85% RH Wireless Connectivity Wi-Fi 2.4GHz IEEE 802.11 Wireless Profile HomeKit RF Characteristics Smart Relay 1 Double Sided Foam Pad 1 N Power input for neutral wire Operating frequency:
2.4GHz Range: 50m~80m Internal antenna L Power input for live wire OUT Output for load Instruction Manual Product Size (L*W*H) 2.34in. x 1.55in. x 0.83in.
(59.4mm * 39.3mm * 21.2mm) Wire Connection port Fixing Screw 1 Instruction Manual 1 Installation Instructions Setup Code Caution: Read this manual before attempting to install the device! Using this product in a manner other than intended voids your warranty. Further, Focalcrest is NOT liable for any damage incurred with the misuse of this product. Caution: All installations of this device should be performed by a qualified or licensed electrician!
Caution: Product must be installed on a 10A line. Caution: Metal casings, mirrors, electrical appliances, etc., may affect, reduce, or interfere with wireless communication. Warning: Turn OFF electrical power from the breaker box or electrical service panel before installing or servicing this product. Improper use or installation can cause SERIOUS INJURY, DEATH, or LOSS/DAMAGE OF PROPERTY. Caution:
Use this product in an indoor environment. You can choose one of the two diagrams below to connect the wires according to your installation environment. L N N L OUT 1 L N L OUT LOAD LOAD NOTES FOR THE DIAGRAM:
N - neutral wire L - live wire L OUT - output live wire 2 Fix Smart Relay on a flat, cleaned surface Recommended placement Stick the foam pad to the recommended position on the Smart Relay and then place the relay on a flat, cleaned surface. Turn ON electrical power and check if the wires are connected correctly. If wires are properly connected, the indicator light will came on while light(s) connected to the switch is turned on. Disposal Instructions This product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more informa-
tion about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product. Warranty Policy For warranty information, please visit https://www.evvr.io/warranty Operating Instructions Important: The In-Wall Relay Switch can be controlled from a iOS device. Note: The indicator will blink blue every five seconds when the device is in setup mode. To control this HomeKit-enabled accessory, the latest version of iOS or iPadOS is recommended. A customer who owns an Apple TV (4th generation or later) with tvOS 10 or later, an iPad with iOS 10 or later, or a HomePod or HomePod mini can control HomeKit-enabled accessories away from home and automatically through triggers such as time of day, location, sensor detection, or the action of an accessory. Add Smart Relay to Apple HomeKit Troubleshooting Q1 Smart Relay pairing failed. Certifications (regional) FCC ID: 2AYEW-SRHW01 FCC Statement The device may be too far from the gateway/coordi-
nator or routing device, or there may be interference in the current network environment. Add routing devices or bring devices closer to the gateway/coor-
dinator. The device is already joined to another gateway. Please restore the device to its factory default. Q2 Cannot be controlled by gateway/coordinator or other HomeKit devices. The device may be installed in the wrong location, too far from the gateway or routing device, or there may be signal interference. Please check whether there is strong electromagnetic field equipment near the wireless switch and check whether the equipment is installed in a closed metal housing or in a closed concrete wall. Add routing devices or bring devices closer to the gateway/coordinator. Q3 The light turns off automatically after a short period of time (approximately 2 minutes or 150 seconds). 5 SEC The power of the light may exceed the maximum power (AC 110V/ 300W, AC 220V/600W). Please check whether the power of the light exceeds the maximum power. Q4 In case of power loss while the lights were on, the light status is on when power is restored?
Yes. The device will record the status of the light, and after the device is powered off, re-powering will restore the state before the device was powered off. Set the Smart Relay into setup mode by short press the RESET button.
(When the device is not added to the Homekit network, it enters setup mode for 10 minutes each time it reboots) Open the Apple Home app and select Add Accessory Locate and scan the HomeKit setup code on the device or on the front page of this manual, then follow the instructions in the Apple Home app. Unpairing Smart Relay from Wi-Fi Router Restore Smart Relay to factory Settings Press and hold the RESET button for more than 2 seconds (the indicator light will flash once) 2 SEC Press and hold the RESET button for more than 5 seconds (the indicator light will double-flash once) Indicator Light Status Color Activity Wi-Fi Connection HomeKit Connection Blue Red Red Red Glowing Glowing Flashing Double flashing Type of Connected Switch Double-click the reset button to switch between the three switching modes. Switch Indicator toggle switch (device changes status when switch changes status) toggle switch (contact closed - ON, contact opened - OFF) the indicator will blink purple once the indicator will blink purple twice momentary switch the indicator will blink purple three times Legal Notice Use of the Works with Apple badge means that an accessory has been designed to work specifically with the technology identified in the badge and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Apple, HomeKit, HomePod, HomePod mini, iPad, iPhone and Apple TV are trademarks of Apple Inc., registered in the U.S. and other countries and regions.
- Reorient or relocate the receiving antenna.
- Consult the dealer or an experienced technician for help. Important Announcement Important Note Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Please contact us for any technical issue support@evvr.io Rev. A-031821 P/N SRHW01