In-Wall Relay Switch Smart Relay (Z-Wave) Instruction Manual Product Introduction Smart Relay uses Z-Wave wireless technology and may be used in different loads, including incandescent lamps, halogen lamps, LED lamps and fluorescent lamps. It is small in size and may be installed in the box of light fixtures. This device is compatible with standard Z-Wave gateway or devices for remote control and inter-operation. Technical Specifications Fixing hole Rev. A-031821 P/N SRZW01 Model Number SRZW01
*Please see separate Smart Switch Sub-Assembly manual for complete instructions. Input Voltage AC 85V~245V Fastening screws 1 Connect wires per wiring diagram as follows Caution: If you have purchased a Smart Switch Sub-Assembly to use with it, please follow the installation instructions on the Smart Switch Sub-Assembly manual. With Smart Relay, you can turn a traditional lamp into a Z-Wave smart lamp. It is recommended to install Smart Relay near the lamp. Complete Accessories Include Smart Relay 1 Double Sided Foam Pad 1 Max. Load Power Min. Load Power Type of Load Operating Temperature AC 110V/300W AC 220V/600W No limit Lighting 0~40C
(32~104F) Relative Humidity 5~85% RH Wireless Connectivity Z-Wave Wireless Profile Z-Wave 700 RF Characteristics Instruction Manual Product Size
(L*W*H) Operating frequency:
865.2MHz to 926.3MHz Range: 40m~80m Internal antenna 2.34in. x 1.55in. x 0.83in.
(59.4mm * 39.3mm * 21.2mm) Fixing Screw 1 Instruction Manual 1 Installation Instructions RESET Button Indicator Light Panel Connection port N Power input for Neutral wire L Power input for live wire OUT Output for load You can choose one of the two diagrams below to connect the wires according to your installation environment. L N N L OUT 1 L N L OUT LOAD LOAD NOTES FOR THE DIAGRAM:
N - neutral wire L - live wire L OUT - output live wire Wire Connection port 2 Fix Smart Relay on a flat, cleaned surface Device Identification QR Code (Z-Wave) Caution: Read this manual before attempting to install the device! Using this product in a manner other than intended voids your warranty. Further, Evvr ApS is NOT liable for any damage incurred with the misuse of this product. Caution: All installations of this device should be performed by a qualified or licensed electrician!
Caution: Product must be installed on a 10A line. Caution: Metal casings, mirrors, electrical appliances, etc., may affect, reduce, or interfere with wireless communication. Warning: Turn OFF electrical power from the breaker box or electrical service panel before installing or servicing this product. Improper use or installation can cause SERIOUS INJURY, DEATH, or LOSS/DAMAGE OF PROPERTY. Caution:
Use this product in an indoor environment. Recommended placement Stick the foam pad at the recommended position on the Smart Relay and then place the relay on a flat, cleaned surface. Turn ON electrical power and check if the wires are connected correctly. If they are correct, the indicator light will be on when the load light, the light(s) connected to the switch, is on. Operating Instructions Important: The In-Wall Relay Switch can be controlled from a mobile phone when used with a Z-Wave gateway. SmartStart Inclusion Smart Relay can be added into a Z-wave network by scanning the Z-Wave QR code. Note: The QR code can be found on the Smart Relay or in the manual. Note: If your controller does not support SmartStart inclusion, please proceed inclusion manually. Restore Smart Relay to factory settings mportant Announcement Important Note Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Press and hold the RESET button for more than 5 seconds. If the Smart Relay is successfully restored to factory settings, the indicator will show RED when the load light is on. Disposal Instructions Add the Smart Relay into the controller by scanning the Z-Wave QR code. The Smart Relay will start SmartStart inclusion by power cycle or tum on the light through Smart Switch Sub-Assembly. If the Smart Relay is successfully paired, the indicator will show BLUE when the load light is on. Note: After scanning the QR code and powering up near the network, the Smart Relay will be automatically added within 10 minutes if no action is taken. Manually Inclusion/Exclusion 1. Before pairing or unpairing Smart Relay, you need to set your Z-Wave gateway into inclusion or exclusion mode. Set Z-Wave gateway into inclusion mode by adding device. Set Z-Wave gateway into inclusion mode by adding device. 2. Set Smart Relay into inclusion/exclusion mode Note: The device may require a Device Security Key (DSK) during the inclusion process, which can be found on the Smart Relay or in the manual. 30 SEC Set the Smart Relay into inclusion/exclusion mode by short press the RESET button. The load light must be on, at the same time the indicator light will slowly flash blue, wait until inclusion/exclusion is successful or until 30 seconds timeout. If the Smart Relay is successfully inclusion/exclusion, the indicator will show BLUE/RED when the load light is on. Troubleshooting Q1 Smart Relay pairing failed. Certifications (regional) FCC ID: 2A68U-SRZW01 The device may be too far from the gateway/coordi-
nator or routing device, or there may be interference in the current network environment. Add routing devices or bring devices closer to the gateway/coor-
dinator. FCC Statement The device is already joined to another gateway. Please restore the device to its factory default. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
Q2 Cannot be controlled by gateway/coordinator or other Z-Wave devices.
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device may be installed in an unreasonable location, too far from the gateway or routing device, or interference. Please check there may be signal whether field equipment near the wireless switch and check whether the equipment is installed in a closed metal housing or in a closed concrete wall. Add routing devices or bring devices closer to the gateway/coordinator. is strong electromagnetic there Q3 The light turns off automatically after a short period of time (approximately 2 minutes or 150 seconds). The power of the light may exceed the maximum power (AC 110V/ 300W, AC 220V/600W). Please check whether the power of the light exceeds the maximum power. Q4 In case of power loss while the lights were on, the light status is on when power is restored?
Yes. The device will record the status of the light, and after the device is powered off, re-powering will restore the state before the device was powered off. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
interference to
- Reorient or relocate the receiving antenna.
- Consult the dealer or an experienced technician for help. This product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product. Warranty Policy For warranty information, please visit https://www.evvr.io/warranty Please contact us for any technical issue support@evvr.io Rev. A-031821 P/N SRZW01