Installing the ExtremeMobility 802.11 ax Indoor AP510i Access Point Overview of the AP510i The AP510i is a next generation, indoor ceiling mount model enterprise class 802.11ax access point. The i in AP510i indicates that it comes with internal antennas. The AP features a dual-band radio, a band locked radio, and comes with eight WiFi internal antennas and one Bluetooth Low Energy (BLE) antenna. The AP510i can be mounted on a dry or wood wall, solid flat ceiling, junction/
gang box, and on a suspended or drop ceiling. Figure 2 AP510i back ports Note: The mounting procedures for installing the AP using the WS-MBI-
DCFLUSH (ordering part #37211) adaptor to a T-bar, WS-MBI-DCMTR01
(ordering part #30518) to a T-bar, and using the main mounting bracket
(ordering part #37201) along with a flat metal-easy attach adaptor (ordering part #37210), Accessory BRKT-000147A-01 (beam clip), and KT-135628-01 are covered in the ExtremeWireless AP510i Installation Guide. Note: The AP510i requires a minimum base firmware of WiNG 7.0. Table 2 Description of back ports on AP510i The AP510i model has the following features:
Radios: 2 radios (1 dual band, 2.4GHz and 5GHz, and 1 band locked 5GHz);
1 IoT Radio (2.4 GHz) Console Port: RJ45 Two Ethernet Ports One multi-rate GE/2.5GE/5GE port (LAN1) with PoE 10/100/1000 Ethernet Port (LAN2) with PoE LEDs: 6 All LEDs will be on during reset. One Reset button Power: PoE 802.3af; 12VDC external power in connector (see Table 1 for details) Antennas:
Eight WiFi internal One BLE internal antenna antennas Temperature:
0 to +40C (32F to 104F) operating temperature Enclosure: Plastic only In Figure 1, the top image indicates the top view of AP510i. In the bottom one, you can see the side view of AP510i. Figure 1 Top and Side View of AP510i Number Description 1 2 3 4 5 Kensington lock 12V DC Power Supply Console Port LAN 2 (GE) LAN 1 (5 GE) LEDs Status The LEDs are located on the front face of the AP but are not visibly marked. Table 3 AP510i LED Status LED Icon Description LED Color Status GE1 Ethernet GE2 Ethernet GREEN AMBER AMBER GREEN PURPLE AMBER GREEN Radio #1 Status GREEN AMBER WHITE GREEN AMBER BLUE OFF Radio #2 Status IoT (BLE) Normal operational status Non-operational status 100 Mbps 1000 Mbps 2.5G/5G 100 Mbps 1000 Mbps 2.4GHz 5GHz Sensor 5GHz 5GHz Indicates BLE is enabled Non-operational status For detailed installation information about the AP510i, see the ExtremeWireless AP510i Installation Guide. Verifying the AP510i Box Contents Verify the contents of the box and ensure that the following items are available:
Table 4 Contents of the AP510i Box Quantity Item 1 1 1 1 2 2 AP510i Quick Reference Mounting Bracket for 802.11ax Indoor AP Cloud Quick Start Card AP510i access point Phillips Pan-head wood screws Screw-in anchors Mounting and Connecting the AP Electrical Hazard: Only qualified personnel should perform installation procedures. Use these instructions as guidelines for mounting and connecting the AP510i easily and safely. The AP510i comes with a Mounting Bracket (#37201) that can be used to mount the AP on a flat t-bar with flat ceiling tiles, flat surfaces, and beams. An adaptor and brackets are available for mounting the AP to non-flat ceiling tiles and t-bars. To mount the AP510i on a junction/gang box, use the optional bracket (WS-MBI-WALL04; #30516). All additional and optional parts are sold separately. 1 USB Port Table 1 AP510i Powering Methods Power Source Description Power over Ethernet
(PoE) External 12V DC power supply (optional; ordering part #37219- PWR 12VDC, 3A, 2.5mm x 5.5mm connector) Power is provided through the RJ45 Ethernet port (LAN port) to the right of the 12V DC port of AP510i, compliant to be powered by 802.3af and 802.3at. This is the preferred method of powering the AP on ceiling and high wall installations. The AP510i can also be powered by an external DC power supply plugged into an AC source. Plug the supplys input jack into the DC-In port. Note: PoE is disabled when external power supply is used. Mounting the AP on a Dry or Wood Wall/Solid Flat Ceiling Pre-installation checklist:
The mounting surface, item, and hardware must be able to support the AP in all environmental conditions. The mounting surface should be flat. To install the AP on a dry wall or flat surface:
Option 1: Using the Main Mounting Bracket 1 Use the mounting bracket as a template and mark the hole centers on the wall. Note: The four feet of the bracket and the direction of the arrow mark must be vertical and pointing up and the flat part of the bracket must be touching the surface it is being attached to. 2 Insert the screws into the holes of the mounting bracket and use the screw-
in anchors if needed. 3 Insert the Ethernet cables RJ45 connector into the LAN1/GE1 port. 4 Insert the AP onto the brackets four feet and slide it down to lock it in place. Option 2: Using an optional Wall and Box bracket Note: Mounting the AP to a flat ceiling requires the WS-MBI-
WALL04 (#30516) bracket, two Philips Pan-head screws, and two screw-in anchors. 1 Install the WS-MBI-WALL04 bracket onto a wall/ceiling with two screws and anchors if appropriate, and ensure that the locking tab is on the top side. Figure 3 Mounting the AP using the optional wall and box bracket Use the optional wall and box bracket as a template and mark the holes to be used. For wall mounting procedure, Extreme Networks recommends using the A or B hole centers. Mark the hole centers to be used, on the attachment surface. Drill the holes and attach the bracket using the screws and anchors 2 Connect the LAN/Ethernet cable to the AP. 3 Insert the AP onto the keyhole posts and slide the AP and lock it into place provided in the kit. at about 1/4th inch. Mounting the AP to a Suspended or Drop Ceiling The AP510i can be mounted to a suspended or drop ceiling directly using the mounting bracket on the t-bar. If there is a ceiling tile protrusion, add the optional T-bar adaptor to the main mounting bracket prior to T-bar installation. Option 1: Using the Main Mounting Bracket to a Flat T-bar Before installation ensure that:
The base thickness of the T-bar that supports the ceiling tile is 0.031. The maximum base thickness of the T-bar of the T-bar is 0.055. Note: The T-bar width can be either 9/16 (15mm) or 15/16 (24mm). 1 Remove the ceiling tiles, push and rotate the main mounting bracket onto the T-bar in such a way that the center angled locking tabs of the main bracket gets attached to the T-bar (Figure 4). Figure 4 Attaching the main mounting bracket to a T-bar 2 Replace the tiles to hold the T-bar in place. 3 Hold the AP and rock it back and forth to ensure it is securely mounted. 4 Attach the Ethernet cables RJ45 connector to the LAN1/GE1 port. Option 2: Mounting the AP by attaching an adaptor to the main bracket Note: Mounting the AP to a suspended or drop ceiling requires the optional adapter (Universal Mounting Kit for WLAN APs; # KT-
135628-01). The adaptor requires a flat t-bar and fits a ceiling tile with up to a 0.35 protrusion from the T-bar. 1 Attach the T-bar adaptor by lining up the small bends on the adaptor with the long raised parts on the main bracket, pull up on the adaptors locking pin, and twist. Make sure the locking pin goes into the locking pin hole on the main bracket and locks in place. Figure 5 Attaching the adapter to the main bracket 2 Slide the T-bar holder onto the T-bar and replace the tiles to hold the adaptor onto the T-bar. 3 Hold the AP and rock it back and forth to ensure that it is securely mounted. 4 Attach the Ethernet cables RJ45 connector to the LAN/GE port. The optional WS-MBI-DCMTR01 (#30518) adaptor can also be used for T-bar installations without the mounting bracket. For detailed instructions, see the ExtremeWireless AP510i Installation Guide. Mounting the AP to a Bracket on a Junction or Gang Box To mount the AP to a Bracket on a Junction or Gang box:
1 Use the Wall and Box Bracket WS-MBI-WALL04 (#30516). 2 Remove the screws from the junction/gang box. 3 Line up the bracket holes on the junction/gang box and ensure that they align. If the holes do not align, drill new holes. Note: When you line up the holes, the locking tab on the bracket must be pointing up and the junction/gang box must be fully covered by the bracket. The bracket must be square to the rest of the room walls and the two holes that are being used must be on the opposite side of large center hole on the bracket. Note: If the holes that you need to use are not near the corners of the bracket, break off the corner to decrease brackets visibility once the AP is installed. 4 Using the holes aligned together or the new ones drilled, attach the bracket to the junction/gang box using the screws removed from the box earlier. Caution: Over tightening the screws will cause the bracket to bend. If the bracket bends, you will not be able to slide the AP onto the keyhole posts. 5 Connect the LAN/Ethernet cable to the AP. 6 Align the keyhole slots and posts and slide the AP onto the bracket until you hear it lock in place. Mounting the AP to a Beam Pre-installation checklist:
The beam must be able to support the AP in all environmental conditions. The beam should be flat. Before attaching the AP onto a beam, verify that:
Beam attachment area is at least 0.5 (12.7mm) wide and as long as the APs largest dimension. Beam mounting surface is less than 0.650 (16.5mm) thick. To attach an AP to a beam, attach a beam clip (Accessory BRKT-000147A-01) to the mounting bracket:
1 Attach the adapter to the mounting bracket by using a twisting motion. 2 Attach the mounting bracket to the AP. 3 Place the adapter on a beam in such a way that there is enough space between the screw and clamp to be tightened. 4 Use the screw and clamp on the top of the adapter to secure the AP in place on the beam. 5 Insert the Ethernet plug into the AP. Connecting a Power Supply to the AP510i If you need to power the AP510i with an external 12V DC power supply, you can plug the power cord into the power connector on the back of the AP. There is no wall mount for the 12V DC power supply. When the device is powered on, the power LED on the front face of the AP is lit. Refer to the ExtremeWireless AP510i Installation Guide for information about optional power supplies. LAN/Console Connections The AP510i has two LAN (Ethernet) ports and a Console port. During administration and maintenance through the LAN or Console, the AP must still have a power connection through either an Ethernet PoE cable or a DC power supply. Regulatory and Compliance Information Safety Guidelines This section contains notices that are intended to protect your personal safety and prevent damage to the equipment. Qualified Personnel:
Electrical Hazard: Only qualified personnel should perform installation procedures. Within the context of the safety notes in this documentation, qualified persons are defined as persons who are authorized to commission, ground and label devices, systems, and circuits in accordance with established safety practices and standards. A qualified person understands the requirements and risks involved with installing outdoor electrical equipment in accordance with national codes. Warning: MPE Statement - Mobile device: This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 26cm between the radiator & your body. Federal Communications Commission (FCC) Notice Warning: Dclaration d'exposition aux radiations: Cet quipement est conforme aux limites d'exposition aux rayonnements ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 26cm de distance entre la source de rayonnement et votre corps. Other Countries Brazil Este produto est homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Resoluo n. 242/2000 e atende aos requisitos tcnicos aplicados. Este equipamento no tem direito proteo contra interferncia prejudicial e no pode causar interferncia em sistemas devidamente autorizados. Para maiores informaes, consulte o site da ANATEL www.anatel.gov.br Hazardous Substances This product complies with the requirements of Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the Increase the separation between the equipment and receiver. receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. Warning: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 26cm between the radiator & your body. Industry Canada Notice This device complies with ISEDs licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d ISED applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Caution: The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. Caution: Avertissement: les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux. Warning: IC Radiation Exposure Statement: This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 26cm between the radiator & your body. CE Information The device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range. AT EE IT PT BE FI LV RO BG FR LT SK HR DE LU SI CY EL MT ES CZ HU NL SE DK IE PL UK All Operational Modes 2.4GHz: 802.11b, 802.11g, 802.11n (HT20), 802.11n (HT40), 802.11ax (HEW20), 802.11ax
(HEW40), 802.15.4 (Thread), Bluetooth (LE) 5GHz: 802.11a, 802.11n (HT20), 802.11n (HT40), 802.11ac (VHT20), 802.11ac (VHT40), 802.11ac (VHT80), 802.11ac (VHT160), 802.11ax (HEW20), 802.11ax (HEW40), 802.11ax
(HEW80), 802.11ax (HEW160) The frequency and the maximum transmitted power in EU are listed below:
2412-2472MHz: 19.98 dBm 2402-2480MHz (LE): 6.23 dBm 5180-5240MHz: 22.98 dBm 5260-5320MHz: 22.98 dBm 5500-5700MHz: 29.98 dBm 2405-2480MHz: 6.48 dBm European Waste Electrical and Electronic Equipment
(WEEE) Notice In accordance with Directive 2012/19/EU of the European Parliament on waste electrical and electronic equipment (WEEE):
1 The symbol above indicates that separate collection of electrical and electronic equipment is required. 2 When this product has reached the end of its serviceable life, it cannot be disposed of as unsorted municipal waste. It must be collected and treated separately. 3 It has been determined by the European Parliament that there are potential negative effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment. 4 It is the users responsibility to utilize the available collection system to ensure WEEE is properly treated. For information about the available collection system, please contact Extreme Environmental Compliance at Green@extremenetworks.com. Declaration of Conformity in Languages of the European Community English Finnish Dutch French Swedish Danish German Greek Icelandic Italian Spanish Portuguese Malti Hereby, Extreme Networks, declares that the radio equipment type
(AP510i) is in compliance with Directive 2014/53/EU. For full text of the EU Deceleration of Conformity, please contact Extreme Regulatory Compliance at compliancerequest@extremenetworks.com Valmistaja Extreme Networks vakuuttaa tten ett Radio LAN device
(AP510i) tyyppinen laite on direktiivin 2014/53/EU oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. Hierbij verklaart Extreme Networks dat het toestel Radio LAN device
(AP510i) in overeenstemming is met de essentile eisen en de andere relevante bepalingen van richtlijn 2014/53/EU. Par la prsente Extreme Networks dclare que l'appareil Radio LAN device (AP510i) est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 2014/53/EU. Hrmed intygar Extreme Networks att denna Radio LAN device
(AP510i) str I verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr av direktiv 2014/53/
EU. Undertegnede Extreme Networks erklrer herved, at flgende udstyr Radio LAN device (AP510i) overholder de vsentlige krav og vrige relevante krav i direktiv 2014/53/EU. Hiermit erklrt Extreme Networks die bereinstimmung des "WLAN Wireless Controller bzw. Access Points" (AP510i) mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 2014/53/EU. Extreme Networks Radio LAN device (AP510i) 2014/53/EU. Extreme Networks lysir her med yfir a thessi bunadur, Radio LAN device (AP510i), uppfyllir allar grunnkrofur, sem gerdar eru i R&TTE tilskipun ESB nr 2014/53/EU. Con la presente Extreme Networks dichiara che questo Radio LAN device (AP510i) conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 2014/53/EU. Por medio de la presente Extreme Networks declara que el Radio LAN device (AP510i) cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 2014/53/EU. Extreme Networks declara que este Radio LAN device (AP510i) est conforme com os requisitos essenciais e outras disposies da Directiva 2014/53/EU. Hawnhekk, Extreme Networks, jiddikjara li dan Radio LAN device
(AP510i) jikkonforma mal-htigijiet essenzjali u ma provvedimenti ohrajn relevanti li hemm fid-Dirrettiva 2014/53/EU. ExtremeMobilityTM Access Points Quick Reference AP510i-FCC AP510i-WR AP510i-FCC-TAA Copyright 2019 Extreme Networks, Inc. All Rights Reserved. Notice Legal Notices Extreme Networks, Inc. reserves the right to make changes in specifications and other information contained in this document and its website without prior notice. The reader should in all cases consult representatives of Extreme Networks to determine whether any such changes have been made. The hardware, firmware, software or any specifications described or referred to in this document are subject to change without notice. Trademarks Extreme Networks and the Extreme Networks logo are trademarks or registered trademarks of Extreme Networks, Inc. in the United States and/or other countries. All other names (including any product names) mentioned in this document are the property of their respective owners and may be trademarks or registered trademarks of their respective companies/owners. For additional information on Extreme Networks trademarks, please see:
www.extremenetworks.com/company/legal/trademarks/
Documentation, Installation Videos, & Support For product support, including Documentation and Installation Videos, visit:
www.extremenetworks.com/documentation P/N 9035993-01